4-663-200-03 (1) AIT Library Page 4 Quick Start Guide Page 10 ___________________________ JP ________________________________ GB LIB-81 © 2002 Sony Corporation INFORMATION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Caution The mains plug on this equipment must be used to disconnect mains power. Please ensure that the socket outlet is installed near the equipment and shall be easily accessible. Notice Use the power cord set approved by the appropriate testing organization for the specific countries where this unit is to be used. WARNING Before performing any installation or maintenance procedures, be sure that the library power switch is in the off position and that the power cord is disconnected from the library. WARNING The standalone library weighs around 13.5 kg. At least 2 people are needed to move or lift the library. Make sure you install the rack-mount library in the lowest possible location in the rack. For best results, use a rack with extension support legs. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. This device requires shielded interface cables to comply with FCC emission limits. If you have any questions about this product, you may: · Call Sony Technical Support at 1-888-530-7669 · Write to: Sony Electronics, Inc., Attn: ISSC Chantilly, Technical Support 4200-Q Lafayette Center Drive Chantilly, VA, 20151-1208 · Or email: issc@am.sony.com 2 Declaration of Conformity Trade Name: Model No.: Responsible Party: Address: Telephone No.: SONY LIB-81 Sony Electronics Inc. 680 Kinderkamack Road, Oradell, NJ 07649 USA 201-930-6972 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Diese Ausrüstung erfüllt die Europäischen EMC-Bestimmungen für die Verwendung in folgender/folgenden Umgebung(en): ·Wohngegenden ·Gewerbegebiete ·Leichtindustriegebiete (Diese Ausrüstung erfüllt die Bestimmungen der Norm EN55022, Klasse B.) ACHTUNG Zur Trennung vom Netz ist der Netzsecker aus der Steckdose zu ziehen, welche sich in der Nähe des Gerätes befinden muß und leicht zugänlich sein soll. HINWEIS Hinweis: Der höchste Schalldruckpegel beträgt 70 dB(A) order weniger gemäß ISO7779. Operating environment Installation Horizontal Temparature 10 ºC to 35 ºC Relative Humidity 20 % to 80 % (no condensation) Ratings Input Voltage 100 - 240 V Frequecny 50 / 60 Hz Current AIT-1 Model AIT-2 Model AIT-3 Model Weight approx. 13.5 kg 50W (Max) 50W (Max) 55W (Max) LED Notice: This product is classified as a CLASS 1 LED PRODUCT. Bei diesem Laufwerk handelt es sich um ein LED-Produkt der Klasse 1. The LED of the barcode reader incorporated inside this product complies with IEC 60825-1. LED (barcode reader) Wavelength: 630-660 nm 3 ........................................................................................5 .......................................................................5 ...........................................................................6 ..........................................................6 .........................................7 / ...................................................................8 ....................................................................................9 © 2002 Sony Corporation. All rights reserved. SonyStorStationAdvanced Intelligent Tape VCCI B 4 13.5kg 2 PDF CD-ROM CD-ROM PDF LIB-81 1 1 SCSI 1 1 CD-ROM 1 ACY-FL81 4 1 1 1 1 2 JP PDF CDROM / 5 13.5kg 1 43 0m m 66 0m m 2 ± 1 1° 1° 1° 1° EIA STANDARD 19 150mm 430mm 150mm 660mm 6 / SCSI LVD Ultra2 Wide SCSI AIT-3 Ultra 160/m SCSI LVD 68 SCSI PDF 2 SCSI 2 SCSI 1 SCSI SCSI 2 1 2 HVDHigh Voltage DifferentialSCSI SCSI Wide SCSI Wide SCSI LVDLow Voltage DifferentialSCSI SCSI SCSI 12m 2m 30cm SCSI SCSI PDF SCSI SCSI SCSI PDFSCSI 1 7 / 3 10 DHCP 30 PDF 2 1 SCSI ID PDF LIB-81 Initializing 1 2 MENU 2 v 9.System Down ENTER Menu 7.Move Tape 8.Password 9.System Down 12:34 Jan/01/2001 12:00:00 [ENTER] to set the Date and Time [CANCEL] to exit 3 2.Shutdown ENTER System Down 1.Reset 2.Shutdown 12:34 2 ENTER CANCEL PDF 2 4 ENTERto activate ENTER Shutdown READY AIT3 [ENTER] to activate 1 5 2 6 3 7 4 8 Shutdown *** wait a minute *** 8 / 5 PDF PDF Ready for shutdown Press the power switch on the rear of the Library PDF 3 10 9 Table of Contents Unpacking ............................................................ 11 Checking the Package Contents ......................... 11 Installing the AIT library ................................... 12 Connecting the Power Cable .............................. 12 Connecting to the Host Computer ..................... 13 Turning the Power On/Off .................................. 14 What's next? ........................................................ 15 © 2002 Sony Corporation. All rights reserved. Trademarks · Sony, StorStation and Advanced Intelligent Tape are trademarks or registered trademarks of Sony Corporation in this country, other countries, or both. · Other product names are trademarks or registered trademarks of their respective owners in this country, other countries, or both. 10 Unpacking Note Checking the Package Contents After opening the package, make sure that all of the following items are present. Contact your dealer if anything is missing. The Operating Instructions for this manual are provided in PDF format on the CD-ROM. After setting up the equipment as described in this manual, please read the Operating Instructions (PDF) on the CD-ROM and make necessary settings. · · · · · · · LIB-81 main unit (1) Power cable (1) SCSI terminator (1) Quick Start Guide (1) CD-ROM (this manual) (1) Air Filter (ACY-FL81) (4) Safety Notice (1) Notes · The AIT library weighs approximately 13.5 kg / 29.8 lbs. At least two people are needed in order to handle the library. Handling the AIT library on your own could result in back injury or other accidents resulting in injury or damage to the AIT library. · You will need the box, packing materials and transport screw if you wish to move or transport the AIT library in the future. Retain them for future use. 1 Remove the AIT library from the box as indicated on the box. Remove the packing materials, such as plastic covers and tapes. With a coin, remove the transport screw from the library bottom and set it in the bottom hole (safe position). Remove the transport screw by turning it counterclockwise. 2 · In addition to the above, other documentation and papers may also be included in the package. · These instructions (this Quick Start Guide) are also included in PDF format on the CD-ROM. GB Transport screw Safe position Unpacking / Checking the Package Contents 11 Installing the AIT library The library weighs about 13.5 kg (29.8 lb.) and has the following dimensions. Before installing the library, make sure that the surface on which you are placing it is large and strong enough. Connecting the Power Cable 1 Confirm that the power switch on the rear of the AIT library is turned off (a is pressed). 43 0m m (16 .9 i n.) 66 0m m .0 (26 in. ) 2 Also, set the library horizontally so that its front and sides are inclined by no more ±1 degree in any direction. Front Connect one end of the power cable to the power supply connector and the other end to the electric outlet. 1° 1° Side 1° 1° With the rack mounting kit, ACY-RK2 (sold separately), the AIT library can be installed on an EIA_STANDARD 19-inch rack. Contact your dealer for information about the rack mounting kit. Note Install the AIT library on a horizontal surface near an AC power outlet. Also, leave a gap of about 150mm (5.9 in.) behind the rear of the unit to allow air to circulate. Rear 150mm (5.9 in.) Front 430mm (16.9 in.) 660mm (26.0 in.) 12 Installing the AIT library / Connecting the Power Cable 2 Connecting to the Host Computer Connect the AIT library and the host computer with a SCSI cable. This section explains general connecting steps. To connect, use the Ultra2 Wide SCSI LVD cable sold at stores. However, when using a model equipped with an AIT-3 drive, use an Ultra 160/m SCSI LVD cable. The library side uses the 68-pin half pitch connector. When connecting other SCSI devices together with the AIT Library, see "Connecting SCSI Peripheral Devices" in the "Others" chapter in the "Operating Instructions" (PDF). Caution Attach the SCSI cable and terminator as shown in the figure below. 1 Use a SCSI cable (sold at stores) to connect the AIT library to the host computer. 2 Attach the provided terminator to connector. Host computer 1 Terminator 2 · Do not connect the AIT library to the HVD (High Voltage Differential) SCSI bus. If connected, the library or other devices on the SCSI bus may be damaged. · When connecting the Wide SCSI cable, turn off all of the connecting devices, including the libraly and the host computer. · When connecting the AIT library as the last device on the SCSI bus, be sure to attach the provided terminator. · In LVD (Low Voltage Differential) SCSI, make the total length of the SCSI cable (internal and external), which connects the host computer and the device at the end of the SCSI bus, shorter than 12 meters (39 ft. 4.4 in). (The length of the AIT library internal cable is 2 meters (78.7 in.).) · Using SCSI cables longer than 30cm (11.8 in.) to connect between devices is recommended. · SCSI cables cannot be branched. Notes · For information about the SCSI bus, refer to "SCSI Specifications" in the "Others" chapter, in the "Operating Instructions" (PDF). · Prepare the necessary SCSI cables. For information about SCSI cable specifications, refer to "SCSI Cable and Terminator Specifications" in the "Others" chapter, in the "Operating Instructions" (PDF). 1 Confirm that the power to the host computer and AIT library are turned off. Connecting to the Host Computer 13 3 Turning the Power On/ Off Turn the Power On Turn on the AIT library power, then turn on the host computer power. After pressing the power switch on the rear of the library, wait at least 10 seconds before turning on the host computer. When using DHCP, wait a least 30 seconds. Then go to "Initial Setup" in "Installation" chapter 2, in the "Operating Instructions" (PDF). Notes 1 Press the power switch on the rear of the library. · If you start the host computer before the library, the SCSI ID is not detected correctly. Therefore, you must always start the library before starting the host computer. · If the library does not work as above, refer to "Troubleshooting" in the "Others" chapter, in the "Operating Instructions" (PDF). Turn the Power Off Before turning off the library, perform the system shutdown procedure from the control panel. When you have performed the procedure, you can turn off the library. The following message appears and the startup process begins. (Startup takes several minutes.) LIB-81 Initializing When the startup process ends, the library enters the time setting mode. 1 2 At the status display, press the [MENU] button for two seconds. Press the v button to select "9. System Down", then press the [ENTER] button. Menu 7.Move Tape 8.Password 9.System Down 12:34 3 Jan/01/ ...