3-252-842-12(1) Remote Commander RM-V202 4 Enter the component's code number. For example, if you're entering the code for a Philips VCR, you would press -35. 5 Press and release the ENT button to store the code number in the Commander's memory. 0 3 ENT 5 Your Code Number Changing the Component Type on the CBL/ SAT and DVD buttons At the factory, "cable box" is assigned on the CBL/SAT button and "DVD player" on the DVD button. By completing the following procedure, you can change this setting so that you can set up any component on these buttons. 1 While pressing the SET button, press the POWER button. 2 Press the CBL/SAT or DVD button. 3 Press and release the x (stop) button. 4 Press and release one of the following buttons; 1 to assign a VCR 2 to assign a DAV 3 to assign a digital satellite receiver, a digital cable box or a digital video recorder 8 to assign a TV 9 to assign an analog cable box - to assign a DVD 5 Press and release the ENT button. 6 Enter the component's code number by following steps 2 to 6 of "Entering the Code Number", or steps 1 to 7 of "Searching for the Correct Code." Operating a DVR (Digital video recorder) Operating a digital cable box 3 To use the "FAVORITE" function 4 To switch the output of the SAT receiver to the TV. (When connecting a TV cable or antenna to the receiver, the output switches between a TV and SAT program). 6 To turn on the display. 8 To move the cursor upward, downward, to the left, or to the right. 9 To call up the MENU display. 0 and ql To play. *2N: *2m: To rewind. *2M: To fast-forward. *2zREC: To record, press N while pressing zREC. First release N, then release zREC. To stop recording, perform the same procedure. *2x: To stop. *2X: To pause. and qd To change the channel. (for example, to change to channel 5, press 0 and 5, or press 5 and ENT). CH+: Channel up. CH­: Channel down. To exit the setting menu. To turn on the display of a shortcut menu. To call up the title bar and toggle the title bar on/off in CABLE mode. To bring up the Station Index when a program guide is not displayed. To select the channel that is highlighted. DAV (DVD/Receiver combo) 3 To select numbers 10 and above. 4 To change the input mode. 5 VOLUME +: Volume up (DAV). VOLUME ­: Volume down (DAV). 6 To show the current play status on the screen. 7 To mute the volume. Press again to turn muting off. Remote Button Descriptions SET TV POWER VCR CBL / SAT DVD General 1 To set up the Commander, press SET while pressing POWER. 2 Component select buttons. To switch to the operations of each component, press the button on which that component is assigned. 5 Volume up: + Volume down: ­ 7 To mute the volume on TV. qa To turn on and off the power of the selected component. Operating Instructions Manual de instrucciones (parte posterior) © 2003 Sony Corporation Printed in China 6 Go to "Step 2: Checking if the Code Number Works" to finish setting up. 1 4 7 PIP VOL 2 5 8 0 TV / VIDEO DISPLAY 3 6 9 ENT CH If you press a wrong button in step 4 Press the POWER button while pressing the SET button and then go back to step 2. English Step 2: Checking if the Code Number Works SLEEP MUTING RECALL For the customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Installing the Batteries Before replacing the batteries, have new ones ready beforehand. Slide open the battery compartment and insert two size AA (R6) batteries (not supplied). Be sure to line up the + and ­ on the batteries with the + and ­ on the battery compartment. 1 Power on the component you want to set up. 2 Aim the Remote Commander at the component and press a button to check if that button works. For example, press the POWER button to see if it works on your component . 3 Check that the other buttons of the Commander is operating the corresponding functions of the component. You can write down the code number on the label inside the battery compartment lid. If the Commander Doesn't Seem to Be Working... · First, try repeating these setup procedures using the other codes listed for your component (see the supplied "Component Code Numbers"). · If ­ after trying all the codes listed for your component ­ you still cannot get the Commander to work properly, try the search method described in "Searching for the Correct Code." MENU GUIDE OK REC 1 2 Operating a Component 1 Press the button of the desired component on the Commander. TV VCR CBL / SAT DVD 3 (*1LIST) To call up the title of the recorded program. 4 To switch the output of the SAT receiver to the TV. (When connecting a TV cable or antenna to the receiver, the output switches between a TV and SAT program). (*1THUMBS+) To select the desired recorded program. (It is necessary to have recorded the desired program). 6 To turn on the display. (*1THUMBS­) To select the desired recorded program. (It is necessary to have recorded the desired program). 8 To move the cursor upward, downward, to the left, or to the right. 9 To call up the MENU display. (*1EPG) To access to all aspects of the service. 0 and ql N: To play. m: To rewind. M: To fast-forward. qs qf qg qh qj qk Operating a TV 3 To operate the Picture-inPicture function. Press each button or combination of buttons as described in the table below. 4 To change the input mode. 6 To display the current channel on TV. 8 To move the cursor upward, downward, to the left, or to the right. 9 To call up the MENU display. qs and qd To change the channel. For example, to change to channel 5, press 0 and 5 (or press 5 and ENT). PIP operations Press PIP GUIDE m or M zREC x N X To Turn on/off the "window" picture. Turn off the "window" picture. Change the TV channel in the "window" picture. Change the input mode of the "window" picture. Move the location of the "window" picture. Swap the "main" picture and the "window" picture. Freeze the "window" picture. When to replace the batteries Under normal conditions, batteries will last up to 6 months. If the Commander does not operate properly, the batteries might be worn out. Replace the batteries with new ones. zREC: To record, press N while pressing zREC. First release N, then release zREC. To stop recording, perform the same procedure. x: To stop. X: To pause. and qd To change the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENT). CH+: Channel up. (*1PAGE+) Page up. CH­: Channel down. (*1PAGE­) Page down. To clear the setting. To exit the setting menu. (*1REPLAY) To replay. Or to go into REC/REVIEW mode during play. (After about 5-second rewind, replay begins). To bring up Master Guide. (*1Live TV) To bring up Master Guide. To bring up the Station Index when a program guide is not displayed. To select the channel that is highlighted. qf CHANNEL +: Presetting or turning frequency to a higher: +. CHANNEL ­: Presetting or turning frequency to a lower: ­. To switch the subtitle. To display the Top Menu. To change the sound. To enter the selection of the MENU display. qs Component code numbers / Números de código de componentes English TV/VCR/COMBO* Analog cable box/ Adaptador para cable analógico Brand Hamlin/Regal Jerrold/G.I Oak Panasonic Pioneer Scientific Atlanta Tocom Zenith Code No. 022, 023, 024, 025, 026 031, 001, 002, 003, 004, 005, 006, 007, 008, 018, 022, 032 027, 028, 029 019, 020, 021 014, 015 009, 010, 011 031, 016, 017 012, 013 qf qg qh qj 8 To move the cursor upward, downward, to the left, or to the right. 9 To call up the MENU. qa To turn the power on/off. qs Number buttons: To set items selected on the screen. qg qh qj qk The left row of the table shows the brand, the center row shows the component (TV, VCR or COMBO) and the right row shows the code No. * COMBO stands for the unit combined with TV and VCR. qk ql N: m: M: x: X: To play. To rewind. To fast-forward. To stop. To pause. Analog cable box, SAT (digital satellite receiver), digital cable box, DVR (digital video recorder), DVD and DAV qd To enter the setting. The left row of the table shows the brand and the right row shows the code No. Digital cable box/Decodificador digital Español TV/VCR/COMBO* Brand Sony Jerrold/G.I. Motorola Panasonic Philips Scientific Atlanta Specifications Operable distance Power requirements Battery life Dimensions Mass Approx. 7 m (23 ft) (varies depending of the component of each manufacturer) Two size AA (R6) batteries (not supplied) Approx. 6 months (varies depending on frequency of use) Approx. 55 × 200 × 32 mm (w/h/d) (2 1/4 × 7 7/8 × 1 5/16 in). Approx. 95 g (3.4 oz). (not including batteries) Code No. 013 015 015 021 016 014 *2 The operation of the built-in DVR or the video on demand. La fila izquierda de la tabla muestra la marca, la central el componente (televisor (TV), videograbadora (VCR) o COMBO), y la derecha el número de código. * COMBO significa que la unidad está combinada con un televisor y una videograbadora. Operating a digital satellite receiver 3 To use the "FAVORITE" function. 4 To switch the output of the digital satellite receiver to the TV. (When you connect a TV cable or antenna to the receiver, the output switches between a TV and SAT program). 8 To scroll through the Master Guide. 9 To call up the MENU display. qs and qd To change the channel. For example, to change to channel 5, press 0 and 5 (or press 5 and ENT). qf Channel up: + Channel down: ­ To page through the guide when a program guide is displayed. qg To bring up the Station Index. qh To tune to the last tuned station. qj To bring up the Master Guide. qk To select the channel that's highlighted. To bring up the Station Index when a program guide is not displayed. ql N: To exit the mode. Design and specifications are subject to change without notice. CBL (adaptador para cable analógico), SAT (sintonizador de recepción vía satélite digital), decodificador digital, DVR (Videograbadora digital), DVD (reproductor de discos DVD) y DAV SAT Brand DirecTV Sony Hitachi Hughes Panasonic RCA/Proscan Toshiba 2 Point the Commander directly at the component. 3 Press the button for the function you want to use. See "Remote Button Descriptions" for complete descriptions of the buttons on the Commander. Notes · Replace both batteries with new ones. · Do not take more than 3 minutes to replace the batteries; otherwise, your setting of the code numbers will be erased. Searching for the Correct Code If you've tried all the code numbers listed for your component and you still cannot get the Commander to work (or if your component is not listed in the "Component Code Numbers" tables), try these steps. 1 Power on the component you want to set up. Insert a tape or disc if necessary. 2 While pressing the SET button, press the POWER button. 3 Press the button of the component on the Commander that you want to set up. 4 Press and release the CH+ button. Then press and release the POWER button. 5 Repeat step 4 until the correct code number is found. Each time you press the CH+ button and then the POWER button, a new code number will be transmitted. Keep trying until your component operates by receiving the transmitted signal from the Commander (e.g., the power turns off, the CH+ function works, playback starts, etc). Be patient as you do this; it may take about 70 tries until the correct code number is located. 6 When the correct code is found, press the ENT button to store the code number in the Commander's memory. 7 Check that the Commander is operating the other functions of your component by pressing the corresponding buttons on the Commander. If they seem to be working properly, you're done setting up the Commander. If the component does not operate properly, repeat steps 1 to 6 and search for another code. If you still cannot get the Commander to work properly, see "Troubleshooti ...