DVR-X4/IP Operating Instructions Four Camera DVR System SPECO TECHNOLOGIES 200 New Highway Amityville. NY 11701 Tel. 631-957-8700 Fax. 631-957-9142 www.specotech.com 1 Digital Video Recorder 4 Channel Digital Video Recorder The Factory Default Password is: ADMIN (Administrator): 1 Please refer to page 14 of this manual for "Operation and Setup" Do not change the password before reading this entire manual. 2 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN! CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This label may appear on the bottom of the unit due to space limitations. The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated " dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance (Servicing) instructions in the literature accompanying the appliance. WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNITS NOT SPECIFICALLY DESIGNED FOR OUTDOOR USE TO RAIN OR MOISTURE. Attention: installation should be performed by qualified service Personnel only in accordance with the National Electrical Code or applicable local codes. 3 Power Disconnect. Units with or without ON-OFF switches have power supplied to the unit whenever the power cord is inserted into the power source ; however, the unit is operational only when the ON-OFF switch is in the ON position. The power cord is the main power disconnect for all unites. 4 1.Before reading this document................................................ 5 6 6 7 8 2.Unit Description.................................................................. Front Panel..................................................................... Rear Panel........................................................................ Controller........................................................................ 3.Installation........................................................................ 9 4.Operation........................................................................... 13 Log-in ........................................................................... 13 Record ........................................................................... 14 Play .............................................................................. 19 Setting ........................................................................ 22 5.HDD Bay........................................................................... 6.Specification & Configuration.......................................... 39 37 5 1. Be sure to read this manual before using stand alone DVR Model 1. This document is intended for both the administrator and users of stand alone DVR Model. 2. This manual contains information for configuring, managing and using stand alone DVR Model. 3. To prevent fire or electrical shock, do not expose the product to heat or moisture 4. Be sure to read this manual before using stand alone DVR Model. 5. For questions and technical assistance of this product, contact your local dealer. Strong recommendation on installation of the DVR unit 1. Check electricity at the place you want to install the DVR unit. Make sure it is stable and meets our electricity requirements. Unstable electricity will cause malfunction of the unit or cause critical damage to the unit. 2. Several chips on the main board of the DVR unit and hard disk drive inside the unit generate heat, and it must be properly discharged. Do not put any objects just beside exhaust port on the left side of the unit and do not close up an opening on the right side of the unit. 3. Put the DVR unit at well-ventilated place and do not put heat-generating objects on the unit. When it is installed inside 15 inch mounting rack together with other devices, please check built-in ventilation fan of the rack is properly running. 6 2. Unit Description 1. Front Panel 12 11 14 1 2 3 4 5 6 7 8 9 10 13 If the Input window is covered, the remote controller may not work If several buttons are simultaneously or incorrectly pressed, the system may not function properly. 1.CH1:Camera 1 In Full Screen. 2.CH2:Camera 2 In Full Screen. 3. CH3:Camera 3 In Full Screen. 4. CH4:Camera 4 In Full Screen. 5.QUAD:Changes to quarterly split screen or Full display screen. 6.PTZ: Selects PTZ function to be controlled. 7.PIP/MARK:Assigns PIP(Picture in picture)or MARK IMAGE to protect selected image from being overwritten. 8.FRZ:Display screen is paused during live view or playback. 9.SPEED/SEQ:The display screen automatically rotates. Speed = FF or Rewind during playback. 10.ZOOM:Enlarges the display screen by 200% 11.PLAY/ENTER:Play-Back 12.MENU: System SETUP. 13.Direction button: Use Right/Left/Up/Down arrow keys to navigate menu 14.Lamps: Status indicator 7 2. Rear Panel 1 2 3 4 5 6 7 8 1. RS232 Connection 2. Sensor Input/Output and RS-485 output. 3.TCP/IP Connect 4. Camera Connections with Loop out. 5.BNC Out to monitor 6.S-Video 7.DC Power 8.Fan When connecting with other applications or equipment, be sure to turn off the system. 8 3.Controller 1. 1:Camera 1 In Full Screen. 2. 2:Camera 2 In Full Screen. 3. 3:Camera 3 In Full Screen. 4. 4:Camera 14In Full Screen. 5.QUAD:Changes to quarterly split screen or Full display screen. 6.PIP/MARK:Assigns PIP(Picture in picture)or MARK IMAGE to protect selected image from being overwritten. 7.FRZ:Display screen is paused during live view or playback. 8.SPEED/SEQ:The display screen automatically rotates. Speed = FF or Rewind during playback. 9.ZOOM:Enlarges the display screen by 200% 10.PLAY/ENTER:Play-Back 11.MENU: System SETUP. 9 3.Installation Procedure 1.Camera Connection Connect the camera to the CAMERA INPUT on the Rear Panel of the system. DC LEVEL V.P CH1 CH2 CH3 CH4 VIDEO DC CH1 CH2 CH3 CH4 LENS VIDEO AC24V/DC12 LOOP MONITOR Rear part of CAMERA 2. Monitor Connection (Composite Connection Method) Connect the monitor to the MONITOR OUT on the Rear Panel of the system CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 LOOP MONITOR VIDEO A IN OUT VIDEO B IN OUT VIDEO C IN OUT 10 3. Monitor (S-VHS) Connection Connect S-VIDEO Monitor to MONITOR OUT(S-VHS) on the Rear Panel of the system. CH1 CH2 CH3 CH4 VIDEO A IN OUT VIDEO B IN OUT VIDEO C IN OUT CH1 CH2 CH3 CH4 LOOP MONITOR 4.Sensor Connection Connect the Sensor to the SENSOR INPUT/OUTPUT on the Rear Panel of the system Terminal block RELAY ALARM C NNG DDDD O CON 4321 M D Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Alarm1 Alarm2 Alarm3 Alarm4 GND NO( Normal Open ) NC( Normal Close) COM M N O G ND 4 3 C 2 D C O (1)Relay output : COM+NC, COM+NO OR COM+NC+NO (2)Alarm input : Short-circuit between Alarm1, Alarm2, Alarm3 or Alarm4 and GND is recognized as alarm. N D 1 D D 11 Internal Circuit 5 V D1 Thus, there is a danger of damage, when the sensor input goes to a Negative level or voltage higher than 5V. 5. Network Connection Connect RS-232C, Modem and LAN 6. HDD connection Main board HDD (Default) HDD (Option) (1)Please make it sure to leave HDD cable as folded up small (tied up) (2)when you connect single HDD to I/O Board of DVR unit, and place port 1 at connector of I/O Board and connect HDD to port 3 as shown above picture. (3)When you connect 2 HDD to I/O Board of DVR unit, first unfold HDD cable and place port 2 at connector of I/O Board, and connect no.1 HDD (4)Select jump: Second HDD in slave position 12 7.Power Connection Connect the power to the POWER CONNECTION on the Rear Panel of the system, system will work. DC 12V 13 4. Operation 1. Log-in 1.Power "ON" the unit. Press MENU button to enter the system menu. 2.LOGIN DVR SYSTEM window appears. 3.Use 1.2.3.4 button to enter password that has 1 to 8 numbers. Factory Default password is: "1" Press MENU again to enter Setup features 4. Use MARK button to clear a digit that was entered incorrectly. 5. After entering the password, press MENU button to go back to the system menu. If password entered does not match previously set number ERROR message is displayed. Factory default password is as below. The system is equipped with two passwords. CURENT PW INPUT ADMIN (Administrator): 1 USER (Low Level Operator): 2 "User" will be locked out of certain features for security reasons. "Admin" has full feature access. (1)We recommend that you change the password. To change password go to ID/PW setup from the Miscellaneous menu. (2)Be sure to memorize the changed password. (3)When logged into USER MODE, only DISPLAY SETUP and TIME/DATE TYPE SETUP is possible. 14 2. Record 1. PLAY Changes to Playback Mode from Recording. 2. MODE When MODE button is pressed, the full screen of each channel and quarterly split screen is played by turns. With 1.2.3.4 button, select full screen of each camera. Indicates 60FPS recording speed : 60 Fields/sec Indicates recording mode REC : represents recording in Nothing Mode Field Switch Mode displayed in Quad Indicates conditions recording MOTION : records when motion is detected ALARM : records when alarm condition is detected 2002 / APR / 01 01:00:00 60FPS R EC PM CAM1 CAM2 Indicates camera channel CAM3 CAM4 Recording Basic Screen 3. PIP (1) Press PIP button. (2) Use button to choose the ADDRESS of the PIP camera. (3) Use button to select the command for PIP 15 (4)With Play/Enter button, select ON/OFF. (5)Press PIP button to come back to recording screen 1.Indic ates addres s ofc amera 001~255 3. Set ON/OFF for s elec ted c ommand 2. Select Command FOCUS FAR 2002 / APR / 01 60FPS REC PM 01:00:00 FOCUS NEAR FOCUS AUTO PAN RIGHT PAN LEFT TILT UP TILT DOWN ZOOM IN ZOOM OUT AUTO PAN LIGHT CMD WIPER CMD P/T CH1 FOCUS FAR EXIT : PRESS [P/T] CAM1 CAM2 CAM3 CAM4 PUMP CMD POWER CMD FUNTION 1 FUNTION 2 FUNTION3 PAN/TILT Control Screen (Ex: DRX-502A model) 16 4. PICTURE IN PICTURE (PIP) (1) Use1.2.3.4button to select a camera and set a full screen. PIP is not available in quarterly split screen. (2) Press PIP/MARK button. (3) With button, select the camera channel in full screen, and with button or 1.2.3.4 button, select the channel of smaller screen. (4) Press SEQ/SPEED button to make the image in smaller screen rotate. Indic ates if"SEQ" button selection. Indic ates FRZ § key s elec tion. 2002/APR/1 PM 09:22:06 60FPS REC PIP FL PIP WINDOWS MOVE : OFF MOVE ON/OFF : PRESS PRZ CAM1 PICTURE INPICTURE Screen To change the location of smaller screen, press FRZ button and use to move to desired button 17 5. FRZ (1)Live full screen pauses when FRZ button is pressed. (2) To pause quarterly split screen, press FRZ button, and with 1.2.3.4button FRZ§ message appears and the select channel. On the right of the camera name, LIVE screen. When FRZ selected,1.2.3.4button or QUAD button do not work. To move to full screen of each camera, press FRZ button once more to end Freeze mode. Indic ates if "FRZ" button selection. When #1 camera is paused in QUAD s creen LIVE screen of that channel will pause. When pressed once more, it will come back to 2002 / APR / 01 60FPS REC FRZ PM 01:00:00 CAM1 FRZ CAM2 CAM3 CAM4 PauseScreen 18 6.SEQ (1)In LIVE full screen, press SEQ/SPEED button to make picture from each channel rotate. (2) It does not operate in quarterly split screen. (3) During automatic rotation, press SEQ/SPEED button to stop automatic rotation. (4) During automatic rotation, press QUAD button to stop automatic rotation and move to quarterly split screen. To change the time interval of the automatic rotation It is possible to select between 1 second to 99 seconds. 2002 / APR / 01 60FPS REC PM 01:00:00 2002 / APR / 01 60FPS REC PM 01:00:00 SEQ A CAM1 B CAM2 C CAM3 D CAM4 Fulls creen automatic ally rotates by the v alue of SEQUENCE INTERVAL in A/B/C/D/ A/B/C.. AB CD Quarterly split (Quad) screen Automatic rotation of the Full Screen 7. Sensor Recording (1) When there is an external sensor input, the recording starts. 8. Scheduled Recording Records by date and by day of the week. 9. Recording by MOTION DETECTION Recording is stopped during SYSTEM SETUP. Recording is stopped during playback, or search in playback mode. Recording is not possible if no camera is connected. 19 3. Play 1. Playback setup (1) Press Play/Enter button to begin playback. (2) Display screen as shown on the right will appear (3) Press Play/Enter button again to start playback from START picture. (4) To come back to recording mode. press Play button. 1 Time rec ording started. 2 START END GOTO : : : 2002/APR/12 2002/APR/20 2002/APR/15 AM 07:40:38 PM 02:11:56 AM 00:00:00 Time rec ording ended. 3 Play search Mode Indi ...