Planning Information Undercounter Model 249R Refrigerator / Freezer Freezer compartment Interchangeable door hinge Interior light Serial and model number plate Removable wire shelves Model 249R One piece interior Stationary door shelves Four-sided magnetic gasket Front venting with removable kickplate Door closer from the full-size units Sub-Zero offers in its Built-In and Integrated lines of refrigeration, we round out our product line-up with a line of traditional Undercounter refrigeration which meets all of the exacting standards you have grown to expect from Sub-Zero. If you cannot run water to the space and still want to have the capability of having some ice at your disposal, this unit is for you. It maximizes the refrigeration space and keeps the freezer to a minimum. Keep in mind, however, that unit does not have automatic defrost, but it may be just right for your clients. Aside MODEL 249R Undercounter refrigerator / freezer combination unit 24" (610) depth-true design for a complete built-in look Door accepts custom panels Smooth surface, easy-to-clean one piece interior Freezer compartment has two ice cube trays Manual defrost Interchangeable hinge allows door swing to be reversed in the field Front venting with removable kickplate allows unit to be serviced from the front Solid core door with magnetic gasket and door closer UL approved for US and Canada Two, five and twelve year residential warranty-- exclusions apply; warranty information can be found on our website, subzero.com Dimensions in parentheses are in millimeters unless otherwise specified. 11/06 1 Planning Information Undercounter Model 249R S P E C I F I C AT I O N S Model 249R Overall Width Overall Height Overall Depth O P T I O N A L D O O R PA N E L S Undercounter Refrigerator / Freezer 23 7/8" (606) 33 13/16" (859) 24" (610) 4.4 cu ft (125 L) .7 cu ft (20 L) 34 1/4" (870) 25 3/8" (645) 115 V AC, 60 Hz, 15 amp circuit 354 kWh / $ 33 120 lbs (54 kg) White Enamel Steel Almond Enamel Steel Classic Stainless Steel Refrigerator Capacity Freezer Capacity Minimum Height Required Door Swing Clearance ACCESSORIES Electrical Requirements Hinge conversion kit Overlay panel conversion kit Accessories are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero.com. Annual Energy Usage (based on 9.06 cents per kilowatt hour) Shipping Weight Special Note Door accepts custom wood panels or panels are available as sales accessories Specifications are subject to change without notice. OVERALL DIMENSIONS 33 13/16" (859) 25 3/8" (645) 23 7/8" (606) 24" (610) 24" (610) Dimensions may vary by ± 1/8" (3). Dimensions in parentheses are in millimeters unless otherwise specified. 2 Planning Information Undercounter Model 249R I N S TA L L AT I O N S P E C I F I C AT I O N S 24" (610) ROUGH OPENING DEPTH TOP VIEW 24"(610) ROUGH OPENING WIDTH LOCATE ELECTRICAL WITHIN SHADED AREA 7" (178) 341/2" 81/2" (216) (876) ROUGH OPENING HEIGHT 7" (178) E 101/2" (267) FRONT VIEW DIMENSIONS Finished Rough Opening Width Finished Rough Opening Height Finished Rough Opening Depth Location of Electrical See Installation Instructions shipped with unit for detailed specifications. 24" (610) 34 1/2" (876) 24" (610) Within shaded area Dimensions in parentheses are in millimeters unless otherwise specified. 3 Planning Information Undercounter Model 249R I N S TA L L AT I O N N OT E S Refer to the illustrations and specifications for overall dimensions, finished rough opening dimensions and installation specifics. A 115 V AC, 60 Hz, 15 amp fused electrical supply is required. It is recommended that a separate circuit, serving only this appliance, be provided. All Undercounter models are equipped with a power supply cord with a 3-prong grounding plug which must be plugged into a mating 3-prong grounding type wall receptacle. Locate electrical within the shaded area shown in the illustration on page 3. You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. Refer to the Undercounter Installation Instructions packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Undercounter Model 249R F R A M E D PA N E L S Framed door panels must be 1/4" (6) thick around the perimeter. If the panel is thicker than 1/4" (6), an edge must be routed around the panel to ensure a proper fit. Refer to the illustrations on this page. PANELS 1/4" (6) THICK OR LESS IMPORTANT NOTE: The weight of the panel cannot exceed 20 lbs (9 kg). Trim reveal 1/4" (6) min F R A M E D PA N E L D I M E N S I O N S WIDTH 1/4" (6) HEIGHT Panel Door Panel Handle Recess Location (A) 23 5/8" (600) 30 " (762) 15" (381) 20 lbs (9 kg) Framed door panel 1/4" (6) thick or less Maximum Panel Weight PANELS THICKER THAN 1/4" (6) Trim reveal 1/4" (6) min Rout to 1/4" (6) thickness Framed door panel thicker than 1/4" (6) 4" A H W Framed Door Panel Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Undercounter Model 249R O V E R L AY PA N E L OVERLAY PANEL Rear View 1/8" (3) 5/16" (8) The overlay door panel design allows for a decorative panel to cover the door trim for a more seamless appearance. To achieve this look, the most common way is to work with three panels ­ the decorative 3/4" (19) thick overlay panel, a 0.10" (3) thick spacer panel and a 1/4" (6) thick backer panel. An accessory kit (OVERPAN) is required in order to accommodate the proper installation of the overlay panel. Additional specifications will be provided with the accessory kit. IMPORTANT NOTE: An area must be notched out on the back edge of the overlay panel at both the top and bottom hinges to avoid interference as shown in illustration on this page. Keep in mind that the Sub-Zero door panels have the potential for hitting adjacent cabinets and / or countertops when they are opened. You need to be aware of your surrounding cabinetry and space limitations when using the overlay units. Refer to the full-scale illustration on page 7. You will need to follow the exact dimensions and panel placement for your model to ensure a proper fit. Refer to the overlay panel specifications below. 1" Notch Required for Hinge Clearance (top and bottom) (25) Notch required for hinge clearance H IMPORTANT NOTE: The weight of the panel assembly cannot exceed 20 lbs (9 kg). IMPORTANT NOTE: The total thickness of all panels for an overlay model must be at least 5/8" (16) thick. W Overlay Door Panel O V E R L AY PA N E L D I M E N S I O N S WIDTH HEIGHT Door Panel Door Spacer Door Backer 24" (610) 23" (584) 23 5/8" (600) 30 5/16" (770) 29 3/8" (746) 30" (762) 20 lbs (9 kg) Maximum Weight (panel assembly) Dimensions in parentheses are in millimeters unless otherwise specified. 6 Planning Information Undercounter Model 249R O V E R L AY PA N E L 145° DOOR OPENING (TOP VIEW) 24" (610) CABINETRY OPENING *MODEL 249 OVERLAY MUST EXTEND A MINIMUM OF 1-13/16" (46) BEYOND SURFACE OF ADJOINING CABINETRY AND MUST BE 1" (25) FROM ADJACENT CABINETRY TO ALLOW THE MAXIMUM DOOR SWING DOOR CLOSED 1"* (25) 3/4" (19) 113/16" (46) DOOR PANEL DOOR PANEL DOOR OPEN @ 145° 145°* Dimensions in parentheses are in millimeters unless otherwise specified. 7 ...