Planning Information Built-In Model 601RG All Refrigerator with Glass Door Lighted electronic control panel Serial and model number plate 601RG Triple-pane UV resistant lowenergy glass door Adjustable spill-proof glass shelves Model 601RG/F Framed Egg container Four-sided magnetic gaskets Model 601RG/O Overlay High humidity compartment Door closers Hermetically sealed refrigeration units Front venting allows unit to be completely built in Removable kickplate (Stainless steel design shown) Model 601RG/S (P/B) Stainless Steel With the installation of a harness kit, these appliances are Star-K compliant to meet strict religious regulations in conjunction with specific instructions found on star-k.org. You may purchase this harness kit through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero.com. The Sub-Zero Model 601RG all refrigerator with glass door is available in your choice of the framed, overlay or stainless steel design application. Three stainless steel finishes are offered--classic (/S), platinum (/P) and carbon (/B). handsome addition to Sub-Zero's inventory of models offers you the ability to complement the commercial looking kitchen with ease. There are, obviously, no door shelves, but there is no loss of storage space in this unit. A roll-out utility drawer is available as an option. Even with the glass door on this unit, you can assure your clients that this model still meets Department of Energy numbers. This Dimensions in parentheses are in millimeters unless otherwise specified. 11/06 1 Planning Information Built-In Model 601RG F E AT U R E S 36" (914) wide all refrigerator with glass door Energy Star qualified Sub-Zero's refrigeration system ensures the freshest food and energy efficiency Shallow-depth design means access is easy to any area of the refrigerator Electronic digital controls are up front and easy to use Bright interior lighting Adjustable, spill-proof glass shelves High-humidity crisper drawer is large and deep with removable divider and smooth sides for easy cleaning Door alarm will let you know with an audible beeping if your refrigerator door is left ajar Triple-pane UV-resistant low-energy glass door improves insulation Front venting allows unit to be completely built in and serviced from the front UL approved for US and Canada Two, five and twelve year residential warranty ­ exclusions apply; warranty information can be found on our website, subzero.com OVERALL DIMENSIONS 35 1/4" (895) 3/8" (10) FRAME EXTENSION 23 7/8" (606) BEHIND FRAME 73" (1854) 36 1/16" (916) 36" (914) 24" (610) 36" (914) Stainless steel design shown. Dimensions may vary by ± 1/8" (3). Dimensions in parentheses are in millimeters unless otherwise specified. 2 Planning Information Built-In Model 601RG S P E C I F I C AT I O N S Model 601RG Overall Width Overall Height MODEL OPTIONS All Refrigerator with Glass Door 36" (914) 73" (1854) 24" (610) 20.1 cu ft (569 L) 72 3/4" (1848) 36 1/16" (916) 115 V AC, 60 Hz, 15 amp circuit 400 kWh / $ 37 Overall Depth 601RG/F 601RG/O 601RG/S 601RG/P 601RG/B Refrigerator Capacity Minimum Height (levelers in) Door Swing Clearance Electrical Requirements Framed Design Overlay Design Classic Stainless Steel Platinum Stainless Steel Carbon Stainless Steel You must allow 90 days from order to delivery for platinum and carbon finishes. Annual Energy Usage (based on 9.06 cents per kilowatt hour) Energy Star Qualified Shipping Weight ACCESSORIES Side panels in white, almond and classic stainless steel Extended framed handle Stainless steel and polished chrome handles for overlay design Roll-out deli basket Dozen egg container with lid 90° and 105° door stop kits Accessories are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero.com. Framed ­ 400 lbs (181 kg) Overlay ­ 400 lbs (181 kg) Stainless Steel ­ 430 lbs (195 kg) Model 601RG has a triple-pane UV-resistant low-energy glass door Special Note Specifications are subject to change without notice. Dimensions in parentheses are in millimeters unless otherwise specified. 3 Planning Information Built-In Model 601RG I N S TA L L AT I O N S P E C I F I C AT I O N S 24" (610) ROUGH OPENING DEPTH TOP VIEW 351/2" (902) ROUGH OPENING WIDTH 723/4" (1848) ROUGH OPENING HEIGHT LOCATE ELECTRICAL WITHIN SHADED AREA 24" (610) 6" (152) 11" (279) E FRONT VIEW DIMENSIONS Finished Rough Opening Width Finished Rough Opening Height Finished Rough Opening Depth Location of Electrical See Installation Instructions shipped with unit for detailed specifications. Refer to the Sub-Zero Design Guide pdf file for additional specifications. 35 1/2" (902) 72 3/4" (1848) 24" (610) Within shaded area Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Built-In Model 601RG I N S TA L L AT I O N N OT E S Refer to the illustrations and specifications for overall dimensions, finished rough opening dimensions and installation specifics. Allow the door to open a minimum of 90° or you'll have problems removing drawers. With the door opening at 90°, you may have to move drawers slightly to clear the door interior. Refer to the minimum door swing clearance in the specifications chart. For corner installations, allow for a minimum 3" (76) filler so that the door can open to 90°. If you're using raised panels, consider using a wider filler. A 90° door stop is available as an accessory. When units are installed side by side, a filler strip is recommended. The width of this filler strip will vary depending on the configuration and panels you use. An anchoring kit may also be used to attach two units together. This kit is available through your Sub-Zero dealer. Be sure to add the filler strip width to your finished rough opening dimension. In any sideby-side installation without a filler strip, add an additional 1/2" (13) to your combined numbers. This will allow for the proper width. Refer to the full-scale illustrations at the end of this section for specifics on door openings and filler size alternatives. If your client has chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and handle hardware. You will not have to install front panels. If your client has chosen the framed or overlay design, you will be adding front panels to give the unit the custom Sub-Zero look. The overlay design also allows you to add your own handles, or you may choose accessory handles available through your Sub-Zero dealer. Refer to pages 6­10 for detailed information on adding panels. The refrigerator door panel must include a cut-out to accommodate the window. Refer to the panel specifications for exact dimensions. The glass portion of the door must be exposed and not covered by any part of the panel. A 115 volt, 60 Hz, 15 amp electrical supply is required. The supply circuit for this appliance must be protected by a 15 amp fuse or circuit breaker. It is recommended that a separate circuit, serving only this appliance, be provided. All Built-In models are equipped with a 6' (1.8 m) power supply cord with a 3-prong grounding plug which must be plugged into a mating 3-prong grounding type wall receptacle. Locate electrical within the shaded area shown in the installation illustration. You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with an anti-tip blocking kit. If there is a solid soffit above the unit with clearance between the unit and the soffit of 1" (25) or less, you won't need to block the unit. For installations with clearances of more than 1" (25), you must block the unit with the anti-tip blocking kit (wood block and hardware) provided with each Built-In unit. Refer to the Built-In Installation Instructions packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Built-In Model 601RG A D D I N G PA N E L S In your plan for panels, be sure you are working with the Sub-Zero panel design family called for in your design. If you have chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and handle hardware. You will not have to install front door panels. If you and your client have ordered a framed or overlay design model, you will be adding panels to give the unit the custom Sub-Zero look. Specifications on the following pages provide installation considerations for framed and overlay door panels. Side panels can be used with the framed, overlay and stainless steel design applications. Refer to specifications on page 10. Dimensions in parentheses are in millimeters unless otherwise specified. 6 Planning Information Built-In Model 601RG F R A M E D PA N E L S If the thickness of the custom panels is less than 1/4" (6), they must be backed up with a sheet of shim material to build the total thickness to 1/4" (6). If the panel is thicker than 1/4" (6), an edge must be routed around the panel to ensure a proper fit. Refer to the illustrations on this page. F R A M E D PA N E L S PANELS 1/4" (6) THICK OR LESS Trim reveal 1/4" (6) min IMPORTANT NOTE: Routing, recessing or optional extended handles may be required on raised panels for finger clearance under the handle. Refer to the full-scale illustrations on pages 11 ­ 14. IMPORTANT NOTE: The weight of each panel cannot exceed 50 lbs (23 kg). 1/4" (6) Panel Framed door panel 1/4" (6) thick or less The traditional framed models come with an 11" (279) louvered grille and elegant full-length handle. Optional extended full-length handles that provide additional finger clearance for raised panels are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero.com. To install framed panels, refer to the installation instructions shipped with each unit. These instructions can also be found on our website, subzero.com. The refrigerator door panel must include a cut-out to accommodate the window. Refer to the chart below for exact dimensions. The glass portion of the door must be exposed and not covered by any part of the panel. PANELS THICKER THAN 1/4" (6) Trim reveal 1/4" (6) min Rout to 1/4" (6) thickness F R A M E D PA N E L D I M E N S I O N S Framed door panel thicker than 1/4" (6) WIDTH HEIGHT Door Panel Handle Recess Location B B B 34 1/8" (867) 5815/16" (1497) A ­ 29 15/32" (749) 25 3/8" (645) 41 3/16" (1046) B ­ 4 3/8" (111) 50 lbs (23 kg) Window Cut-Out Window Cut-Out Location Maximum Panel Weight 14" (356) H A 13 3/8" (340) W Framed Door Panel C Dimensions in parentheses are in millimeters unless otherwise specified. 7 Planning Information Built-In Model 601RG O V E R L AY PA N E L S O V E R L AY PA N E L S The overlay design allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room. To achieve this look, the most common way is to work with three panels--the decorative overlay panel, a .10" (3) spacer panel and a 1/4" (6) backer panel. Depending on your cabinet manufacturer, this could be one panel routed for different dimensions or more likely, three different panels. Regardless of the physical construction of the panels (routing or three panel assembly), you will need to follow the exact dimensions and panel placement to ensure a proper fit. The top illustration on this page is a cross section view of the three panel assembly showing placement of the door / drawer / grille trim. The bottom illustration shows a rear view of the three panel assembly and critical dimensions, standard for all overlay models. Overlay models will come with no handle hardware, because the beauty of this design is that you can match the surrounding cabinetry hardware. For overlay door panel dimensions, refer to specifications on page 9. IMPORTANT NOTE: Keep in mind that the Sub-Zero door panels have the potential for hitting adjacent cabinets and/or countertops when they are opened. You need to be aware of your surrounding cabinetry and space limitations when using the overlay models. Refer to the full-scale illustrations on pages 13 ­14. IMPORTANT NOTE: The weight of each door panel assembly cannot exceed 50 lbs (23 kg). The total thickness of all panels for an overlay model must be at least 5/8" (16) thick. To install overlay panels, refer to the installation instructions shipped with each unit. These instructions can also be found on our website, subzero.com. Spacer Panel .10" (3) Overlay Panel 1/4" (6) Backer 5/16" (8) min P ...