Planning Information Built-In Model 695 Side-by-Side Refrigerator / Freezer with Ice and Water Dispenser Front venting allows unit to be completely built in Hermetically sealed refrigeration units Serial and model number plate Lighted electronic control panel Model 695/F Framed Automatic ice maker Adjustable dairy compartment Freezer utility rack Adjustable spillproof glass shelves Adjustable wire shelves Bulk ice dispenser Adjustable door shelves Model 695/F Partial Framed Roll-out freezer baskets Adjustable roll-out utility basket Adjustable door shelves Four-sided magnetic gaskets Egg tray Removable kickplate Model 695/O Overlay High humidity crisper drawer (Stainless steel design shown) Door closers With the installation of a harness kit, these appliances are Star-K compliant to meet strict religious regulations in conjunction with specific instructions found on star-k.org. You may purchase this harness kit through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero.com. Model 695/S Classic Stainless Steel The Sub-Zero Model 695 side-by-side refrigerator / freezer with ice and water dispenser is available in your choice of the framed, partial framed, overlay or stainless steel design application. The stainless steel model comes with classic stainless steel wrapped doors. Sub-Zero offers two distinctive different models with ice and water dispensing through the door. This sideby-side unit is 48" (1219) wide and the dispenser is placed on the refrigerator door to offer a sleek look and most efficient use of interior storage space. Dimensions in parentheses are in millimeters unless otherwise specified. 11/06 1 Planning Information Built-In Model 695 F E AT U R E S 48" (1219) wide side-by-side refrigerator / freezer with ice and water dispenser Framed, overlay and classic stainless steel applications provide complete design flexibility If you choose not to use custom wood panels above or below the glasswell, you can order a partial framed accessory kit for your framed unit ­ the kit includes molding and a stainless steel panel that surrounds the glasswell and runs the total height of the refrigerator door With the framed retrofit accessory kit, existing Model 690 door panels can be used on a new Model 695 framed unit Sub-Zero's dual refrigeration system ensures the freshest food and energy efficiency Shallow-depth design means access is easy to any area of the refrigerator Electronic digital controls are up front and easy to use Bright interior lighting Adjustable, spill-proof glass shelves High-humidity crisper drawer is large and deep with removable divider and smooth sides for easy cleaning ­ there are even two added storage drawers Door alarm will let you know with an audible beeping if your refrigerator or freezer door is left ajar Automatic ice maker provides an ample supply of crescent-shaped ice ­ also has a bulk ice dispenser Solid core doors with magnetic gaskets and door closers Front venting allows unit to be completely built in and serviced from the front Meets strict Department of Energy requirements UL listed for US and Canada Two, five and twelve year residential warranty ­ exclusions apply; warranty information can be found on our website, subzero.com OVERALL DIMENSIONS 471/4" (1200) 237/8" 3/8" (10) FRAME EXTENSION (606) BEHIND FRAME 84" (2134) 291/4" (743) 48" (1219) 48" (1219) 24" (610) Stainless steel design shown. Dimensions may vary by ± 1/8" (3). Dimensions in parentheses are in millimeters unless otherwise specified. 2 Planning Information Built-In Model 695 S P E C I F I C AT I O N S Model 695 Overall Width Overall Height MODEL OPTIONS Side-by-Side Refrigerator / Freezer with Ice and Water Dispenser 48" (1219) 84" (2134) 24" (610) 18.2 cu ft (515 L) 9.8 cu ft (278 L) 83" (2108) 29 1/4" (743) 115 V AC, 60 Hz, 15 amp circuit 1/4" Overall Depth 695/F 695/F 695/O 695/S Refrigerator Capacity Freezer Capacity Minimum Height (levelers in) Door Swing Clearance Electrical Requirements Framed Design Partial Framed Design (accessory kit required) Overlay Design Classic Stainless Steel ACCESSORIES Plumbing Requirements Water Supply Annual Energy Usage (based on 9.06 cents per kilowatt hour) Shipping Weight copper line 20­100 psi FRAMPAR ­ Partial framed kit includes molding and a stainless steel insert panel for above and below the glasswell on a framed unit FRAMRET ­ Framed retrofit kit includes moldings and stainless steel insert panels to accommodate existing Model 690 framed door panels Louvered, panel or stainless steel grilles in 1" (25) increments from 10" (254) to 15" (381) high Front and grille panels for framed design in white, almond and classic stainless steel Side panels in white, almond and classic stainless steel Stainless steel and polished chrome handles for overlay design Gallon door shelf Dozen egg container with lid 90° and 105° door stop kits Accessories are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero.com. 747 kWh / $ 68 Framed ­ 610 lbs (277 kg) Overlay ­ 610 lbs (277 kg) Stainless Steel ­ 656 lbs (298 kg) Overlay design is now available for this ice and water dispensing unit Special Note Specifications are subject to change without notice. Dimensions in parentheses are in millimeters unless otherwise specified. 3 Planning Information Built-In Model 695 I N S TA L L AT I O N S P E C I F I C AT I O N S 24" (610) ROUGH OPENING DEPTH EXTEND WATER LINE APPROX. 36" (914) FROM BACK WALL SHUT-OFF VALVE TOP VIEW 7" (178) E 6" (152) LOCATE ELECTRICAL WITHIN SHADED AREA 471/2" (1207) ROUGH OPENING WIDTH 833/4" (2127) ROUGH OPENING HEIGHT WITH STANDARD 11" (279) GRILLE 751/2" (1918) LOCATE WATER SUPPLY WITHIN SHADED AREA 3" (76) 18" (457) 6" (152) W FRONT VIEW DIMENSIONS Finished Rough Opening Width Finished Rough Opening Height Finished Rough Opening Depth Location of Electrical Location of Water Supply 47 1/2" (1207) 83 3/4" (2127) 24" (610) Within upper shaded area Within lower shaded area See Installation Instructions shipped with unit for detailed specifications. Refer to the Sub-Zero Design Guide pdf file for additional specifications. Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Built-In Model 695 I N S TA L L AT I O N N OT E S Refer to the illustrations and specifications for overall dimensions, finished rough opening dimensions and installation specifics. Allow the doors to open a minimum of 90° or you'll have problems removing drawers. With the doors opening at 90°, you may have to move drawers slightly to clear the door interior. Refer to the minimum door swing clearances in the specifications chart. For corner installations, allow for a minimum 3" (76) filler so that the door can open to 90°. If you're using raised panels, consider using a wider filler. A 90° door stop is available as an accessory. Be sure to add the filler strip width to your finished rough opening dimension. In any sideby-side installation without a filler strip, add an additional 1/2" (13) to your combined numbers. This will allow for the proper width. Refer to the full-scale illustrations at the end of this section for specifics on door openings and filler size alternatives. If your client has chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and handle hardware. You will not have to install front panels. If your client has chosen the framed or overlay design, you will be adding front panels to give the unit the custom Sub-Zero look. The overlay design also allows you to add your own handles, or you may choose accessory handles available through your Sub-Zero dealer. Refer to pages 6­12 for detailed information on adding panels. For Built-In models with an automatic ice maker, rough in the water supply line. Connect a 1/4" OD copper line to the house supply, being sure to use an easily accessible shut-off valve between the supply and the unit. Do not use self-piercing valves. A saddle valve kit (4200880) is available from your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero.com. A line filter is required when water conditions have a high sediment content. The ice maker operates on water pressure of 20 psi (1.4 bar) to 100 psi (6.9 bar). In some cases a reverse osmosis water filter system may not be able to maintain the minimum water pressure consistently. The water line should be routed up through the floor within 1/2" (13) from the back wall and no higher than 3" (76) off the floor. If you have to come through the wall, make sure the water line is no more than 3" (76) from the floor. Locate water supply within the shaded area shown in the installation illustration. Regardless of the routing, allow 3' (.9 m) of excess copper tubing to remain outside the wall or floor for easy connection to the unit. A 115 volt, 60 Hz, 15 amp electrical supply is required. The supply circuit for this appliance must be protected by a 15 amp fuse or circuit breaker. It is recommended that a separate circuit, serving only this appliance, be provided. All Built-In models are equipped with a 6' (1.8 m) power supply cord with a 3-prong grounding plug which must be plugged into a mating 3-prong grounding type wall receptacle. Locate electrical within the shaded area shown in the installation illustration. You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with an anti-tip blocking kit. If there is a solid soffit above the unit with clearance between the unit and the soffit of 1" (25) or less, you won't need to block the unit. For installations with clearances of more than 1" (25), you must block the unit with the anti-tip blocking kit (wood block and hardware) provided with each Built-In unit. Refer to the Built-In Installation Instructions packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Built-In Model 695 A D D I N G PA N E L S F R A M E D PA N E L S PANELS 1/4" (6) THICK OR LESS In your plan for panels, be sure you are working with the Sub-Zero panel design family called for in your design. If you have chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and handle hardware. You will not have to install front door panels. If you and your client have ordered a framed or overlay design model, you will be adding panels to give the unit the custom Sub-Zero look. Specifications on the following pages provide installation considerations for framed and overlay door panels. Side panels can be used with the framed, overlay and stainless steel design applications. Refer to specifications on page 12. Trim reveal 1/4" (6) min 1/4" (6) Panel Framed door panel 1/4" (6) thick or less F R A M E D PA N E L S PANELS THICKER THAN 1/4" (6) Trim reveal 1/4" (6) min Rout to 1/4" (6) thickness If the thickness of the custom panels is less than 1/4" (6), they must be backed up with a sheet of shim material to build the total thickness to 1/4" (6). If the panel is thicker than 1/4" (6), an edge must be routed around the panel to ensure a proper fit. Refer to the illustrations on this page. IMPORTANT NOTE: Routing, recessing or optional extended handles may be required on raised panels for finger clearance under the handle. Refer to the full-scale illustrations on pages 13­16. IMPORTANT NOTE: The weight of each panel cannot exceed 50 lbs (23 kg). The traditional framed models come with an 11" (279) louvered grille and elegant full-length handle. Optional extended full-length handles that provide additional finger clearance for raised panels are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero.com. For framed door panel dimensions and dimensions for the optional panel grille for the framed application, refer to specifications on page 7. To install framed panels, refer to the installation instructions shipped with each unit. These instructions can also be found on our website, subzero.com. Framed door panel thicker than 1/4" (6) Dimensions in parentheses are in millimeters unless otherwise specified. 6 Planning Information Built-In Model 695 F R A M E D PA N E L S H W For framed models, the refrigerator door panel must include a cut-out to accommodate the glasswell and bezel. The thickness of the panel in this area can range from 1/4" (6) to a maximum of 1 1/8" (29). If the panel is thicker, prov ...