2356, 2358, 2359 & 2360 Instruc tion Manual DELUXE MIXMASTER ® MIXER Mode d'Emploi BAT TEUR DELUXE MIXMASTER ® s s Instruzioni per l'Uso DELUXE MIXMASTER ® MIXER Gebrauchs anleitung DELUXE MIXMASTER ® MIXER Anvandarhandledning DELUXE MIXMASTER ® MIXERN s s Manual de Iinstruccione s BATIDORA MIXMASTER ® DELUXE IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed including the following: 1. Read all instructions before using the Mixer. 2. To protect against risk of electrical shock, do not put Mixer in water or other liquid. This may cause personal injury or damage to the product. 3. Close supervision is necessary when Mixer is used by or near children, or incapacitated persons. 4. Unplug from outlet while not in use, before putting on or taking off parts and before cleaning. 5. Avoid contacting moving parts. Keep hands, hair, clothing, as well as spatulas and other utensils away from beaters during operation to reduce the risk of injury to persons and/or damage to the Mixer. 6. If the power supply cord of this appliance is damaged, it must only be replaced in a repair shop appointed by the manufacturer, because special tools are required. 7. The use of attachments not recommended or sold by Sunbeam may cause fire, electrical shock or injury. 8. Do not use outdoors or for commercial purposes. 9. Do not let cord hang over edge of table or counter or touch hot surfaces, including the stove. 10. Remove beaters from Mixer before washing. 2 11, Do not place Mixer or bowls on or near a hot gas or electric burner, or in a heated oven. 12. Do not use Mixer for other than intended use. 13. Do not leave Mixer unattended while it is operating THIS UNIT FOR HOUSEHOLD USE ONLY When your Mixmaster" Mixer is first used, you may experience an odor and possibly a slight wisp of smoke from your mixer motor. This is caused by the heat curing of the insulation which protects the motor and is normal. After the first few uses, this effect will disappear. FOR PROOUCTS PURCHASEO IN U.S & CANADA ONLY: TO reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized plug only one way. If the plug does not fit fully in the outlet: reverse the plug. If it still does not fit, contact a qualified electrician. 00 NOT ATTEMPT TO OEFEAT THIS SAFETY FEATURE. FEATURES Thank you for choosing the Sunbeam Deluxe Mixmaster® Mixer. For generations we have been helping cooks prepare moist cakes, light and fluffy meringue, and chewy cookies. You can even make bread with your Sunbeam® Deluxe Mixmaster® Mixer. The Sunbeam® Deluxe Mixmaster® Mixer offers you a choice of 12 different mixing speeds. The bowl-fit beaters and bowls have been designed to mix ingredients thoroughly and evenly. ® The Mix-Finder® dial tells you at a glance which mixing speed to use. No problem ejecting the beaters either ­ just push the ejector button beside the handle. When making bread, the Sunbeam® Deluxe Mixmaster® electronically controls the speed of the dough hooks to deliver just the right power for proper kneading action. You'll love being able to make so many things with your mixer! 11 1 2 3 10 9 8 7 4 5 6 1. Beater Ejector 2. Large Mixing Bowl 3. Small Mixing Bowl 4. Bowl-Fit Beaters 5. Turntable 6. Dough Hooks 7. Stand 8. Worklight* 9. Mixer-Release Trigger 10. Mix-Finder® Dial 3 11. Mixing Guide * Some models do not have the worklight feature. ASSEMBLING THE STAND MIXER Before assembling the mixer, be sure the Mix-Finder® dial is in the ZERO position and the electric cord is unplugged. ATTACHING THE TURNTABLE Place the revolving turntable into the base of the stand using the socket corresponding to the size of the bowl. As you release the mixer-release trigger, the top of the top of the trigger should clamp around the metal pivot. For models equipped with a head-lock feature­To lower the mixer-head for normal operation, support the mixer head with one hand. Then press in on the head-lock latch. Gently lower the mixer head until the mixer head is in a normal operating position. Latched Opening Ball Bearing Extension Mixer-Release Trigger Small Bowl Large Bowl ATTACHING THE MIXER HEAD Press in on the mixer-release trigger, located at the rear of the stand. For models equipped with a head lock feature ­ While pressing in on the mixer-release trigger, press in on the head-lock latch. This is best accomplished by using the thumb and forefinger of the same hand and pressing inward. This will open the top of the stand to receive the mixer head. Place the mixer head on the top of the stand so that the metal pivot, located on the bottom of the mixer head, goes into the open groove on the top of the stand. Mixer Head Mixer-Release Trigger Metal Pivot Be sure the mixer head is securely attached to the stand before using. NOTE: This mixer is NOT intended for use away from the stand. ADDING THE MIXING BOWL Place the desired mixing bowl onto the turntable so that the groove in the bottom of the bowl fits into the correct groove in the turntable. Mixing bowls should NEVER be used in a conventional oven, microwave oven, on top of the range, or on any other heated surface. NOTE: If mixing bowls are scratched or chipped, do not use mixer. Mixer bowl should not be used to blend in hot liquids. Stand 4 Attaching the Beaters Be sure the Mix-Finder® dial is in the ZERO position and unplug electric cord from the electrical outlet. Lift mixer head up and back to pull it out of the way of the bowl, while holding in an upright position. Side of Bowl Conical Beater Square Beater NOTE: It is important that the beaters go into the correct sockets. Otherwise the mixer will not give you the proper mixing action. Do not risk ruining a recipe or damaging your mixer. Read the following instructions carefully. One of the beaters is conical in shape and has a nylon button on the bottom. It goes into the socket on the side of the mixer nearest the side of the bowl. The other beater is square-shaped and goes into the socket nearest the center of the bowl. See beater symbols located on the front of the mixer head. Insert the beaters, one at a time, using a combination pressing and twisting motion, until the beaters snap into position. If a beater should not properly snap into place, pull it out of the socket and rotate it one quarter turn. Reinsert the beater into the socket until it snaps into position. Attaching the Dough Hooks Set the Mix-Finder® dial in the OFF position and unplug the electric cord from the electrical outlet. Lift mixer head up and back to tilt it out of the way of the bowl, while holding in an upright position. NOTE: The dough hooks must go into the correct sockets. The mixer will operate with the dough hooks in the wrong position. However, you will not get proper kneading action and you could risk ruining a recipe or damaging your mixer. Read the following instructions carefully. Square Beater Conical-Shaped Beater Nylon Button 5 The dough hook with the small washer and foot goes into the socket on the side of the mixer nearest the side of the bowl. The other dough hook with the large washer goes into the socket nearest the center of the bowl. See the dough hook symbols located on the front of the mixer head. About the Worklight Feature Some of our models have a worklight that lights the area inside the mixing bowl. As soon as the electric cord is plugged in, the worklight will glow. It will continue to glow until the electric cord is unplugged from the electrical outlet. Worklight Beater-Bowl Drive Adjustment Automatic bowl rotation is factory set. Occasionally, a simple adjustment may be necessary when the bowl fails to rotate. To make this adjustment, tilt the mixer head back. Hold the mixer head in an upright position and locate the adjustment screw on the underside of the mixer head. Loosen the locking nut and turn the adjustment screw on the underside of the mixer head. Loosen the locking nut and turn the adjustment screw clockwise, to lower the mixer head; or counter clockwise, to raise the mixer head. Retighten the locking nut. The beater with the nylon button should lightly touch the bottom of the mixing bowl. Locking Nut Operating Instructions About the Mix-Finder® Dial The Mix-Finder® dial is used for turning the mixer ON and OFF and for selecting its 12 mixing speeds. Rotate the Mix-Finder® dial in a clockwise direction, to increase mixing speed; and in a counterclockwise direction, to decrease mixing speed. As you rotate the Mix-Finder® dial, notice that a numbered speed is aligned with the indicator on top of the mixer head. This numbered speed indicates the speed at which the mixer is operating. Rotate the Mix-Finder® dial until the indicator is opposite the numbered speed you wish to use. Speed Indicator Mix-Finder® Dial Mixing Guide 6 Adjustment Screw Mixing Guide The mixing guide on your mixer has been designed to help you take the guess work out of preparing foods. Next to each of the numbered speeds on the Mix-Finder® dial are descriptions of the mixing task best suited to that mixing speed. Use those descriptions as a mixing guide when preparing your favorite recipes. Speed Setting 1 Mixing Guide Example Fold-Kneaded Use when mixing dry ingredients or when folding two portions of a recipe together, such as a beaten egg white into a batter or when directions call for LOW speed. Use for kneading bread. Stir Blend Use when stirring liquid ingredients or when gentle action is needed to moisten dry ingredients. Use when quick breads require a brisk action, just enough to blend ingredients but not enough to develop a smooth batter. Use when mixing dry ingredients and liquid ingredients together alternately in a recipe. Use when recipe calls for combining ingredients together. Use when preparing packaged cake mixes or when directions call for MEDIUM speed. Use when creaming sugar and butter together. Use to whip potatoes or to develop a smooth batter. Use to whip whipping cream or to develop a light, fluffy texture. Use to beat air into whipped desserts. Use when preparing light, fluffy frostings and candies. Use when aerating eggs and egg whites. Use when directions call for HIGH speed. 2 3 4 5 6 7 8 9 10 11 12 Mix Combine Cake Mixes Cream Whip Whip/Cream Desserts Frostings Egg Whites NOTE: Due to variations in ingredient temperatures and quantities, the Mixing Guide speeds are only suggested. If necessary, adjust speeds as needed to achieve desired results. 7 CARING FOR YOUR MIXER EJECTING THE BEATERS OR DOUGH HOOKS After you've finished mixing, turn the Mix-Finder® dial to OFF and unplug the electric cord from the electrical outlet. Push the ejector button located near the handle to remove beaters or dough hooks. Scrape excess batter off the beaters using a rubber or plastic spatula. Do not strike beaters on the rim of the bowl. To remove the worklight lens, place the Mix-Finder® dial in the ZERO position and unplug mixer from electrical outlet. Remove beaters or dough hooks from mixer sockets and remove bowl from turntable. Holding the mixer head in an upright position, use a small screwdriver to remove the screw holding the worklight lens in place. CLEANING YOUR MIXER To clean the mixer, wipe the mixer head, stand, and turntable with a damp cloth, then dry. DO NOT IMMERSE THE MIXER HEAD OR STAND IN WATER. Avoid the use of abrasive cleaners, as they may mar the finish of the mixer. Wash the beaters and bowls in hot, soapy water after each use. Rinse thoroughly and dry. Beaters and bowls may also be washed in an automatic dishwasher. Squeeze the worklight lens, as shown, until the tabs on the lens clear the housing. Tilt the worklight lens down and out of the housing. CARE AND CLEANING OF THE WORKLIGHT (For models with worklight feature only.). To clean the worklight lens, wash in warm, soapy water. Rinse and dry thoroughly. To replace the worklight bulb, unscrew from socket. Replace with new bulb. The worklight bulb should be replaced as soon as it burns out. You may also wish to remove the worklight lens periodically for cleaning. 8 NOTE: Replacement bulbs may be purchased from local hardware or department stores or from your nearest authorized Sunbeam Service Center (6 watt maximum bulb can be used.) To replace the worklight lens, repeat the steps described in "To remove the worklight lens" in reverse order. MIXING AND BAKING SUGGESTIONS · Ingredients should be added to the mixing bowl as they are specified in the recipe. When combining dry and wet ingredients, you may wish to moisten ingredients on Speed 1 or 2, then turn to the desired mixing speed. · Use the mixing speed that is recommended in the recipe. When using a recipe that is not in this book, use the handy mixing guide on the Mix-Finder® dial of the mixer to help you find the correct speed to use. ...