Visit us at: www.swisherinc.com OWNER'S MANUAL MODEL NO. WB80042F THE FINISHING TOUCH 42" FINISH CUT MOWER SELF PROPELLED WALK BEHIND Read and follow all Safety Rules and Instructions before operating this equipment. Rev. 12.18.2002 Assembly Operation Service and Adjustment Repair Parts 1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093 PHONE (660) 747-8183 FAX (660) 747-8650 Made In The Manufacturing quality lawn care equipment since 1945 ONWB842 USA SAFETY AND OPERATIONAL DECALS Replace decal immediately if damaged. Order by part number from Swisher Mower and Machine Co. Inc. OD36 ­ DEFLECTOR DECAL OD30 ­ WARNING DECAL OD43 ­ FLYING DEBRIS DECAL OD55 ­ DANGER DECAL OD29 ­ SPINNING BLADE DECAL SERVICE AND ADJUSTMENTS Stop engine, let all moving parts come to a complete stop. Disconnect spark plug. BLADE SPINDLE BELT TRANSMISSION BELT BLADE DRIVE BELT BELTS CONFIGURATION BLADE SPINDLE BELT REPLACEMENT REMOVAL · · · · Stop engine, let all moving parts come to a complete stop. Disconnect spark plug. Remove belt cover. Remove Blade Drive Belt. (See Blade Drive Belt replacement.) Pull tension idler away from Blade Spindle Belt to relieve tension. Remove belt. · · · · INSTALLATION Pull tension idler away from belt. Install belt according to above configuration. Install Blade Drive Belt as shown. Install belt cover and tighten hardware. · BLADE DRIVE BELT REPLACEMENT REMOVAL · · · · Stop engine, let all moving parts come to a complete stop. Disconnect spark plug. Disengage all blade controls by releasing the bails. Remove belt cover. Rotate belt off pulleys and pull belt through motor belt guide. INSTALLATION · · · · Route belt as shown. Adjust engage idler tension. Belt should be snug during engagement of blade latch. Too much tension will not allow the blade latch to function properly. Tighten nuts on blade engage cable when finished. Install belt cover and tighten hardware. WHEEL DRIVE BELT REPLACEMENT REMOVAL · · · · Stop engine, let all moving parts come to a complete stop. Disconnect spark plug. Remove belt cover. Remove Blade Drive Belt, (See "Blade Drive Belt replacement") Locate belt guide for wheel drive belt and loosen. Remove wheel drive belt. · · · · INSTALLATION Install belt as shown. Adjust belt guide snug against motor pulley and back off ¼". Tighten belt guide hardware. Install Blade Drive Belt (see "Blade Drive Belt installation"). Install belt cover and tighten hardware. · · Check for loosened bolts, nuts, springs, etc. often. Replace filters, spark plugs as needed. Keep blades in good working order. Adjust Nuts WHEEL BRAKE ADJUSTMENT Adjustment may be necessary if the unit does not stay in position on a hill with the operator bails released, or if the brake drags while in neutral with the "GROUND CONTROL" bail engaged. PROCEDURE · · · · Stop engine, let all moving parts come to a complete stop. Disconnect spark plug. Release "GROUND CONTROL" bail. Adjust nuts forward or backward. When the "GROUND CONTROL" bail is disengaged there should be constant tension on the brake arm. All tension should be off brake arm when "GROUND CONTROL" bail is engaged. Tighten adjustment nut when finished and re-attach spring, if necessary. · WHEEL DRIVE BELT ADJUSTMENT Adjustment may be necessary if loss of traction occurs due to belt slippage. PROCEDURE · · Adjust "GROUND CONTROL" cable in or out to achieve maximum traction. Too much tension will not allow the "GROUND CONTROL" bail to fully activate. Too little tension will allow the belt to slip, resulting in loss of traction. "GROUND CONTROL" bail should fully close against handlebars when functioning properly. · · OVERALL ASSEMBLY When ordering painted parts, please indicate with corresponding letters: C = Red Parts TK = Textured Black Parts REPLACEMENT PARTS When ordering painted parts, please indicate with corresponding letters: C = Red Parts; TK = Textured Black Parts (ex. 4207TK, 4237C) Item # Description Part # 1 Motor Base 4270 2 Wire Link BRS6H 3 Link Spring T2SM 4 5/16-18 Serrated Flange Nut NB170 5 5/16-18 x 21/2 Grade 5 Bolt NB138 6 Shift Linkage 4282 7 Blade Driver Housing B99 8 Brake Spring BT297 9 Brake Pad BP370 10 Blade Engage Idler 4262 11 1/2 -13 Nut NB213Z 12 Brake Pad Clip BP370S 13 5/16 Flat Washer NB556 14 3/8 -16 2-way Locknut NB280 15 5" Chain Links AS080 16 3/8-16 x 2 Grade 2 bolt NB231 17 1/2-13 x 5 Grade 5 bolt NB155 18 Blade Engage Idler Kit 4280 19 1/8 x 1 Cotter Pin NB126 20 Center & Left Blade Driver Kit 9080 21 Blade Bearing B98 22 Center & Left Blade Shaft 9075 23 Washer B98W 24 1/4-20 x 1 Grade 5 Bolt NB250 25 1/4-20 Nylock Nut NB180 26 15" Blade 4221 27 Serrated Belleville Washer NB607 28 3/8 - 24 x 1 1/4 Grade 5 Bolt NB166 29 Blade Mounting Plate 9008 30 3/8-24 2 Way Lock Nut NB216 31 3/8-24 x 1 Grade 5 Bolt NB238N 32 Lower Blade Pulley B4104 33 Pulley Spacer 6104RS 34 Upper Blade Pulley (Center & Left Only) B104 35 3/4-16 2 Way Lock Nut NB629 36 Right Blade Shaft 9077 37 Right Blade Driver Kit 9079 38 Transmission Idler Pulley B27 39 Transmission Idler 4276 40 3/8-16 x 1 1/2 Grade 5 Bolt NB107 41 1/2-13 x 2 1/2 Grade 5 Bolt NB588 42 3/8 SAE Washer NB272 43 Transmission Idler Kit 4281 44 Tension Idler Pulley B527 45 Tension Idler 6681 Item # Description Part # 46 Tension Spring 682S 47 1/2 x 1 9/16 Shoulder Bolt NB220 48 5/16 SAE Washer NB275 49 3/8-16 Grade 2 Nut NB212 50 5/16-18 Nylock Nut NB181 51 Tension Idler Kit 4263 52 Blade Engage Pulley 7509 53 Blade Drive Belt 4220 54 Blade Spindle Belt 4219 55 Wheel Drive Belt 2414 56 Transmission Belt Guide 2451 57 1/4-20 Flange Nut NB524 58 Blade Drive Belt Guide 4234 59 8HP B&S Engine N/A 60 Upper Engine Spacer 689L 61 1/4 x 1/2 Key Stock 4258 62 Upper Engine Pulley 2411 63 Lower Engine Spacers BB105SL 64 1/4 x 1 Key Stock 9031 65 Lower Engine Pulleey 688 66 Belleville Washer 699 67 7/16-20 x 1 1/2 Grade 5 Bolt NB637 68 Height Adjust Arm 4275 69 Front / Rear Torsion Connector 4235 70 Front Torsion Bar 4233 71 Rear Torsion Bar 4236 72 3/4 x 18 GA Washer NB179 73 5/16-18 x 3/4 Serrated Flange Bolt NB596 74 Plastic Belt Cover 4257 75 3/8-16 x 3 Eye Bolt NB635 76 3/8-16 Nylock Nut NB182 77 Front Tire & Wheel 4218 78 Caster 4266 79 5/8 x 10 GA Washer NB149 80 5/8 Flanged Bearing F157B 81 Grass Chute 4261 82 5/16-18 x 8 1/2 Grade 2 Bolt NB136 83 Grass Chute Spring CH5S 84 Plastic Roller AS001 85 5/16-18 x 5 1/2 Grade 5 Bolt NB521 86 1/2 x 14 GA Washer NB177 87 5/16-18 x 4 Carriage Bolt NB101 88 Hanger Bracket 4216 89 1/2-13 2 Way Jam Lock Nut NB121 90 Rear Tire & Wheel 4217 REPLACEMENT PARTS When ordering painted parts, please indicate with corresponding letters: C = Red Parts; TK = Textured Black Parts (ex. 4207TK, 4237C) Item # 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 Description Sway Bar 3/16 x 1 1/2 Keystock 3/4 E-Clip 3/4 x 10 GA Washer 5/16-18 x 1/2 Set Screw 4 Speed Transmission 1/4 SAE Washer Shift Link 1/4-28 x 3/4 Grade 5 Bolt Brake Mount Brake Mount Kit Transaxle Brake Pivot Transaxle Brake Link 1/4-20 x 3/4 Eye Bolt 5/16-18 x 1 Grade 5 Bolt Gear Shift Spring Rear Cover 5/16-18 x 1 1/4 Serr. Flange Bolt Thrust Bearing Plastic Knob Crank Handle Transmission Pulley 3/8 Hardened Washer Wiring Harness Throttle Control 1/4-20 x 1 1/2 Grade 2 Bolt 1/4-20 x 1/2 Self-tapping Bolt ON/OFF Key Switch Throttle Console Gear Shifter Blade Engage Latch 1/4-20 x 2 1/2 Grade 5 Serr. Flange Bolt Operator Handle Transmission Cable Operator Presence Bail (Upper) Ground Control Bail (Lower) 3/16 x 1 Roll Pin Belt Guide Oil Drain Cap Oil Drain Valve 5/16-18 x 1 1/2 Serr. Flange Bolt 3/16 x 3/4 # 9 Woodruff Keystock Frame Deck Part # 4207 2434 NB621 NB184 NB192 4256 NB274 4223 NB620 4273 4271 4247 4264 V139EB NB501 TR148S 4299 NB253 T151 4857 4274 2410 NB196 4268 4226 NB104 NB114 KSM 4292 4260 4295 NB208 2402 2432 4294 4291 NB123 4283 AS123 AS122 NB254 NB638 4269 4250 THE FINISHING TOUCH 42" FINISH CUT MOWER SELF PROPELLED WALK BEHIND OWNER'S MANUAL MODEL NO. WB80042F Each cutter has its own model number. Each engine has its own model number. The model number for the cutter will be found on the right hand side of the motor base. The model number for the engine will be found on the top of the blower fan housing. All cutter parts listed herein may be ordered directly from Swisher Mower & Machine Co. Inc. or your nearest Swisher dealer. All engine parts may be ordered from the nearest dealer of the engine supplied with your cutter. WHEN ORDERING PARTS, PLEASE HAVE THE FOLLOWING INFORMATION AVAILABLE: * * * * PRODUCT ­ FINISHING TOUCH SERIAL NUMBER - _______________ MODEL NUMBER - _______________ ENGINE MODEL NUMBER - _______________ TYPE - _______________ * PART NUMBER * PART DESCRIPTION TELEPHONE - 1-800-222-8183 FAX - 1-660-747-8650 SWISHER MOWER & MACHINE CO. INC. 1602 CORPORATE DRIVE P.O. BOX 67 WARRENSBURG, MO 64093 Visit us at: www.swisherinc.com SWISHER MOWER & MACHINE CO. INC. PRINTED IN U.S.A. ...