User manual SYLVANIA 6842PFM

PLASMA DISPLAY Owner's Manual 6842PF M Before you can view a picture on the plasma display, you must first connect the unit to an external video source. See page 18 of the owner's manual. IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER READING OWNER'S MANUAL, PLEASE CALL TOLL FREE 1-800-605-8453, OR VISIT OUR WEB SITE AT http://www.SylvaniaConsumerElectronics.com. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The important note is located on the rear of the cabinet. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. PORTABLE CART WARNING S3126A RADIO-TV INTERFERENCE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. The serial number of this product may be found on the back of this unit. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Date of Purchase Dealer Dealer Address Dealer Phone No. Model No. Serial No. 2 When moving the plasma display Due to the weight of this plasma display, two people should be used when moving it. Both people should make sure to grasp the top of the display with one hand and the base of the display with the other hand, as in the following illustration. Regarding This Manual · Product and company names appearing within this manual are trademarks or registered trademarks of their respective owners. · Although special care has been taken to ensure that all information contained within this manual is correct at time of writing, the information is subject to change without notice. · Make sure to read the manual carefully and follow all instructions contained within. We will not be held responsible for any damages caused by improper use or handling of this product. · Reproducing this manual by any means, in whole or in part, is prohibited. Figure 1 Optional Accessories To mount the plasma display on a wall, the following accessory is available: VISIONMOUNTTM Flat Panel TV Wall Mount from SANUS SYSTEMS, for large flat panel televisions (32" to 60"). Refer to page 21 for mounting the plasma display. NOTE: The wall mounts are not supplied with the plasma display. # CAUTION · This PDP "6842PF M" is for use only with the Sanus Systems Model VMPL. Wall Mount. Using with other wall mounts may result in instability, causing possible injury. · When mounting the plasma display with the Sanus Systems wall mount, make sure to mount it on the wood studs inside the wall, as failure to do so may result in instability, causing possible injury. · Refer to the instruction manual included with the wall mount for details when securing the plasma display to the wall. 3 IMPORTANT SAFETY INSTRUCTIONS Thank you for purchasing this plasma display. Please make sure to read this manual before using the plasma display and pay particular attention to the Safety Instructions enclosed within. When you have finished reading this manual, store it in a safe place for easy access in the future. CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 INSERTING THE REMOTE CONTROL BATTERIES . . . . . . . . . . . . . . . . . . . . . .5 REMOTE CONTROL RANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 COMPONENT NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 MAIN UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 OPERATING THE PLASMA DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 BASIC OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 SELECTING THE INPUT SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 CHANGING THE ASPECT RATIO (SCREEN MODE) . . . . . . . . . . . . . . . . . . . . . . . . .10 STILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 SLEEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 NAVIGATING THE SET UP MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Layout of the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ENTERING THE MAIN MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 PICTURE SELECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Automatically Adjusting the Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Manually Adjusting the Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Initializing the Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 WINDOW SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 SWITCHING THE DISPLAY LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 SETTING THE SCREEN SAVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 EXTERNAL INPUT TERMINALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 CONNECTING DEVICES TO THE AV INPUT TERMINALS . . . . . . . . . . . . . . . . . . . .18 VIDEO Signal Connection (Basic Signal Transfer) . . . . . . . . . . . . . . . . . . . . . . . . .18 S-VIDEO Signal Connection (Better Signal Transfer) . . . . . . . . . . . . . . . . . . . . . . .18 CONNECTING DEVICES TO THE COMPONENT INPUT TERMINALS . . . . . . . . . . .19 Component Signal (Y, Cb/Pb, Cr/Pr) Connection (Best Signal Transfer) . . . . . . . . .19 CONNECTING PLASMA DISPLAY TO AUDIO SYSTEM . . . . . . . . . . . . . . . . . . . . . .20 AUDIO Signal Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 CONNECTING THE POWER CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 ATTACHING A WALL MOUNT BRACKET (SOLD SEPARATELY) . . . . . . . . . .21 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 CLEANING THE PLASMA DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 REFERENCIA RÁPIDA EN ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 INSTALACIÓN DE LAS PILAS EN EL CONTROL REMOTO . . . . . . . . . . . . . .26 NOMBRES DE LOS COMPONENTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 UNIDAD PRINCIPAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 CONTROL REMOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 4 SUPPLIED ACCESSORIES This product comes with the following accessories: Please confirm that they are included. POWER VOL MUTE SCREEN MODE STILL INPUT SELECT DISPLAY MENU PREVIOUS SLEEP P Owner's Manual (1EMN20890A) P Remote Control (NE801UD) P AA batteries x 2 P Quick Connection Guide (1EMN20891) P Power cable (WBC0182LTE01) NOTE: If any of these accessories are missing, please contact your dealer. INSERTING THE REMOTE CONTROL BATTERIES 1 Remove the back cover of the remote control while pressing the tab on the back cover down with your finger. 3 Replace the back cover of the remote control. 2 Insert two AA size batteries, making sure that the polarities of the batteries match the symbols inside the remote control. NOTE: · Do not insert a mix of old and new batteries. · Do not insert a mix of different brands of batteries or different types of batteries. · Always use new, fresh batteries as replacement. · Never attempt to charge, heat, burn or take apart batteries. REMOTE CONTROL RANGE Operate the remote control within a 30 degree angle on both sides of the infrared sensor on the main unit. You can operate the remote control from a distance of several yards away from the main unit. NOTE: Other devices which use infrared beams, sunlight, fluorescent lights, etc., may affect the range and effectiveness of the remote control. Make sure the plasma display is positioned in a place which minimizes interference from them. With in 30 degrees Approximately 5.5 yds (5 m) POWER VOL MUTE SCREEN MODE STILL STANDBY ON POWER VOLUME INPUT SELECT With in 30 degrees Approximately 5.5 yds (5 m) INPUT SELECT Approximately 7.6 yds (7 m) DISPLAY MENU PREVIOUS SLEEP 5 CONTENTS / SUPPLIED ACCESSORIES / INSERTING THE REMOTE CONTROL BATTERIES / REMOTE CONTROL RANGE COMPONENT NAMES MAIN UNIT Front Figure 2 Rear Figure 3 STANDBY ON POWER VOLUME INPUT SELECT Input Terminals STANDBY ON POWER R AUDIO L VOLUME INPUT SELECT 7 VIDEO2 1 2 3 Infrared Sensor AUDIO OUT S-VIDEO2 Output / Input Terminals AU D I O R AUDIO R R L VIDEO1 S-VIDEO1 L Y Pb Pr AC IN 4 5 L COMPONENT 1 COMPONENT 2 R INNER JACKS L Y Pb Pr 6 7 8 9 1 2 3 4 5 POWER button: Turns the power ON or in STANDBY. ON indicator: Lights up when the power is ON. STANDBY indicator: Lights up when the power is in the standby mode. Disappears when the power is ON. INPUT SELECT button: Selects input terminals. VOLUME K(up) / L(down) button: Increases or decreases the volume. 6 7 8 9 AUDIO OUT: Output terminals for audio. AUDIO/VIDEO/S-VIDEO: Input terminals for an audio and video signal. You can select either VIDEO or S-VIDEO. COMPONENT: Input terminals for a component signal. You can make Y-Pb-Pr progressive or interlaced connection. AC IN terminal: Connect the supplied power cable for a standard AC outlet. 6 REMOTE CONTROL Figure 4 1 POWER VOL 2 3 4 5 6 7 MUTE SCREEN MODE STILL DISPLAY 9 MENU PREVIOUS SLEEP 10 11 8 1 2 3 4 5 6 7 8 POWER button: Turns the main power ON or in STANDBY. VOL K(up) / L(down) button: Increases or decreases the volume. MUTE button: Turns the audio off or on. SCREEN MODE button: Selects aspect ratios available for the screen. STILL button: Pauses the image shown on the screen. INPUT SELECT button: Selects input terminals. DISPLAY button: Displays the name of the selected input terminal on the screen. SLEEP button: Sets the sleep timer. 9 MENU button: Accesses the setup menu, allowing you to access various settings. the setup menu. 10 PREVIOUS button: Moves up one level in 11 K(up) / L(down) button: Selects the various modes in the setup menu. {(left) / B(right) button: Selects and adjusts levels for the various settings. B(enter) button: Also used as the enter button. 7 COMPONENT NAMES INPUT SELECT OPERATING THE PLASMA DISPLAY BASIC OPERATIONS POWER VOL 3 POWER MUTE SCREEN MODE Adjust the volume and screen size according to your requirements. Perform adjustments to the volume (VOL K / L button), screen aspect ratio (SCREEN MODE button), and picture settings (MENU button). NOTE: · When you adjust the volume with the VOL K / L button, a message such as the following is displayed on the screen. This message disappears a few seconds after performing adjustments. STILL INPUT SELECT INPUT SELECT DISPLAY The following is a simple explanation of the procedure for turning the power of the display ON or in STANDBY, and the procedure for selecting the input signal. The procedure described here is for the remote control, however the POWER, INPUT SELECT and VOLUME buttons on the plasma display can also be used in the same way. · If you turn the audio mute on, a message slowly flashes on the screen. At this time, if you press another button, this flashing stops. 1 Press the POWER button. Confirm that the STANDBY indicator is lit before pressing the POWER button. The power turns ON and the ON indicator on the main unit lights up. The STANDBY indicator on the main unit disappears. · To turn the audio mute off, either press the MUTE button again or press the VOL K / L button. · If you press either the PREVIOUS, K, L, B or { button in a mode apart from the image adjustment mode. A message such as the following is displayed. 4 Press the POWER button to turn the power STANDBY. The ON indicator on the main unit disappears and the STANDBY indicator lights up. NOTE: · Even if the power is turned STANDBY, the main unit is in the standby mode. In order to shut the main power of the display OFF, it is necessary to remove the Power cable from the power outlet. 2 Select the input signal by pressing the INPUT SELECT button. Each time you switch the input, the name of the selected input terminal is displayed on the screen for a few seconds. NOTE: · "No signal" is displayed on the screen if there is no input from the selected terminal and there is no message currently displayed on the screen for volume adjustment or the setup menu, etc. · If there is no video signal and there has been no operation from the remote control or the buttons on the main unit for more than 15 minutes, the auto shut-off function activates and the display switches to standby mode. 8 SELECTING THE INPUT SIGNAL Selecting the Input Signal POWER VOL MUTE SCREEN MODE 1 Press the INPUT SELECT button to select the input signal. Each time you switch the input signal, the name of the selected input terminal is displayed on the display for a few seconds. The INPUT SELECT button cycles through the input terminals in the following pattern: Video 1 (S-Video 1) Video 2 (S-Video 2) Component 2 Component 1 STILL INPUT SELECT INPUT SELECT DISPLAY DISPLAY The procedure for selecting the input signal described here is for use with the remote control. However, the INPUT SELECT button on the plasma display can also be used in the same way. NOTE: Displaying the Current Input Signal 1 Press the DISPLAY button. The name of the current input terminal is displayed on the screen. 2 To clear the name of the current input terminal, press the DISPLAY button again or wait for a few seconds. NOTE: · To redisplay the name of the input terminal, press the DISPLAY button again. · When switching the input signal, audio mute turns ON temporarily. · S-VIDEO1 takes preference over the VIDEO 1 jack, as does S-VIDEO 2 over the VIDEO 2 jack. Therefore, if there is input to the VIDEO and S-VIDEO terminals at the same time, the S-VIDEO signal is displayed on the screen. If the S-VIDEO cable is not connected to the plasma display, the VIDEO signal will be displayed on the screen. · Any of the following display formats: 480i, 480p (progressive), 1080i and 720p (progressive) signals can be connected to the COMPONENT1 and 2 terminals. If one of these video signals is detected, the format of the input signal is displayed after the name of the current input terminal as the following. · A "No signal" message appears if there is no video signal and there is no message currently displayed on the screen for volume adjustment or the setup menu, etc. If there continues to be no video signal for some seconds, "No signal" slowly moves around the screen. · If there is no video signal and there has been no operation from the remote control or the buttons on the main unit for more than 15 minutes, the auto shut-off function activates and the display switches to standby mode. 9 OPERATING THE PLASMA DISPLAY OPERATING THE PLASMA DISPLAY CHANGING THE ASPECT RATIO (SCREEN MODE) POWER VOL MUTE SCREEN MODE SCREEN MODE STILL Each time you change the screen mode, the name of the selected mode is displayed on the screen for a few seconds. The SCREEN MODE button switches between the screen modes in the following pattern. Normal Full Wide Zoom INPUT SELECT DISPLAY NOTE: · When switching the input signal, the audio mute turns ON temporarily. · You can only select the "Normal" and "Zoom" screen modes for 1080i and 720p video signals connected to the COMPONENT terminals. By changing the aspect ratio of the screen you can select the manner in which you wish to view the picture. 1 2 Press the SCREEN MODE button to display the current screen mode. Press the SCREEN MODE button a second time to change the screen mode. Mode Normal Picture Explanation Normal will display a 4:3 picture at its standard 4:3 size. For 1080i and 720p video signals, a picture will be displayed at 16:9 size. Normal Full Full Full will display a 4:3 picture at a 16:9 size, with horizontal elongation necessary to fill the screen. Wide Wide Wide will display a 4:3 picture at a 16:9 size, with less horizontal elongation necessary to fill the screen because a little bit of the top and bottom will be cut off. Zoom Zoom Zoom will magnify the entire 4:3 picture to fill the screen, with no horizontal elongation to fill the screen, as more of the top and bottom are cut off. Use this mode to view letterboxed 4:3 picture content to get a widescreen picture. A 16:9 picture will be magnified similarly, but to a lesser extent. 10 STILL POWER VOL SLEEP INPUT SELECT DISPLAY MUTE SCREEN MODE MENU PREVIOUS STILL STILL INPUT SELECT SLEEP SLEEP DISPLAY 1 1 Press the STILL button. The still mode turns on, and the image displayed on the screen is frozen. Press the SLEEP button. The sleep timer is displayed on the screen. NOTE: NOTE: · When the still mode is on, the message "Still" slowly flashes on the screen. · When the still mode is on, the audio is muted. · You cannot turn the still mode on when there is no video signal or when switching between video signals. · If the sleep timer is activated, the remaining time is displayed on the screen. If not activated, "0 minutes" is displayed. 2 Press the SLEEP button to set the time. The SLEEP button switches between the times. 0 minutes 10 minutes 90 minutes 2 Press the STILL button again to turn the still mode off. NOTE: · You can also press the INPUT SELECT, DISPLAY, SLEEP, VOL K(up) / L(down), MUTE, SCREEN MODE or MENU buttons to turn the still mode off. The timer starts counting down after the message displaying the set time disappears (after a few seconds). NOTE: · The remaining time displayed for the sleep timer changes in steps of 1 minute. · To change the set time, repeat the above procedure. 11 OPERATING THE PLASMA DISPLAY You can freeze the image displayed on the screen. You can select the sleep timer. OPERATING THE PLASMA DISPLAY NAVIGATING THE SET UP MENU In the setup menu, you can specify settings for picture adjustment, picture position, language and screen saver. NOTE: · If you do not press any buttons for approximately 20 seconds, the display automatically exits the menu mode. Layout of the Setup Menu The various functions in the setup menu are outlined below: MAIN MENU Picture select Picture mode Dynamic Manual News Brightness Contrast Color Tint Sharpness Cool Color temp. Reset Normal Warm Movie Window setting H-Position V-Position Français Language English Español Slow Detail Screen saver Fast Off 12 ENTERING THE MAIN MENU INPUT SELECT PICTURE SELECT INPUT SELECT DISPLAY DISPLAY K MENU PREVIOUS MENU PREVIOUS MENU SLEEP MENU SLEEP PREVIOUS B L The display enters the main menu and the MAIN MENU is displayed on the screen. "Picture select" is selected on the MAIN MENU. 2 Press the B (ENTER) button. The PICTURE SELECT menu is displayed on the screen. NOTE: · If you press the PREVIOUS button or the MENU button on the MAIN MENU, the menu is cancelled. · For procedures which use the ENTER button, use the B button as the ENTER button. NOTE: · Press the PREVIOUS button to return to the MAIN MENU. Pressing the MENU button cancels the menu. · Picture select display will disappear from the TV screen automatically after about 20 seconds if you do not press any buttons. 13 OPERATING THE PLASMA DISPLAY 1 Press the MENU button. 1 Enter the main menu with the MENU button. OPERATING THE PLASMA DISPLAY INPUT SELECT Manually Adjusting the Picture Settings DISPLAY K MENU PREVIOUS 1 PREVIOUS B SLEEP Select "Picture mode" on the PICTURE SELECT screen with the K / L buttons. Select "Manual" with the { / B buttons. The display enters the manual mode, and you can specify individual adjustments. MENU { L 2 3 Automatically Adjusting the Picture Settings Select the mode to adjust with the K / L buttons. The modes rotate in the following order: "Picture mode" - "Brightness" - "Contrast" - .. ...- "Reset" - "Picture mode" 1 2 Select "Picture mode" on the PICTURE SELECT screen with the K / L buttons. Select the automatic adjustment mode according to the type of picture displayed on the screen with the { / B buttons. 4 Adjust the selected mode using the { / B buttons. NOTE: · If you have selected Brightness, Contrast, Color, Tint, or Sharpness, the menu display disappears, and a bar for adjusting the selected mode appears in the center of the bottom of the screen. · You can select "Color temp." among three modes: "Normal", "Warm" and "Cool". · If you select "Reset" and press the B (ENTER) button, the adjusted values return to their initial settings. 5 6 To adjust a different mode, repeat steps 3 and 4. Press the PREVIOUS button to return to the Picture mode. NOTE: · Pressing the MENU button cancels the menu. NOTE: · There are 3 modes for automatically adjusting the picture settings; "News", "Movie" and "Dynamic". In these modes, you cannot adjust the individual picture settings below "Brightness" even if they are selectable. · MANUAL refers to manual picture settings adjustment. Initializing the Adjustments 1 2 Select "Reset" on the PICTURE SELECT screen with the K / L buttons. Press the B (ENTER) button. The settings you specified individually are initialized (return to their default factory settings). NOTE: · The default factory settings are as follows: PICTURE MODE: Manual BRIGHTNESS: 31/63 CONTRAST: 45/63 COLOR: 31/63 TINT: 31/62 SHARPNESS: 1/2 COLOR TEMP.: Normal 3 Press the PREVIOUS button to return to the MAIN MENU. NOTE: · Pressing the MENU button cancels the menu. 14 WINDOW SETTING INPUT SELECT 4 Select the mode to adjust with the K / L button. Select "H-Position" to move the picture horizontally (left or right) and select "V-Position" to move the screen vertically (up or down). DISPLAY K MENU PREVIOUS MENU { SLEEP 5 B Adjust with the { / B buttons. The { / B buttons are also used for moving the picture vertically. L 6 Press the PREVIOUS button to return to the MAIN MENU. NOTE: · Pressing the MENU button cancels the menu. 1 2 Enter the main menu with the MENU button. Select "Window setting" on the MAIN MENU screen with the K / L buttons. If there is no input from a video signal, "Window setting" is grayed out and you cannot select it. SWITCHING THE DISPLAY LANGUAGE INPUT SELECT DISPLAY K MENU PREVIOUS MENU { SLEEP PREVIOUS B L You can select the language displayed on the screen from English, French and Spanish. 3 Press the B (ENTER) button. The "WINDOW SETTING" menu is displayed on the screen. 1 2 3 4 Enter the main menu with the MENU button. Select "Language" on the MAIN MENU screen with the K / L buttons. Select the language with the { / B buttons. Press the PREVIOUS button to return to the MAIN MENU. NOTE: · Pressing the MENU button cancels the menu. 15 OPERATING THE PLASMA DISPLAY You can move the picture displayed on the screen up, down, left or right. OPERATING THE PLASMA DISPLAY SETTING THE SCREEN SAVER INPUT SELECT 4 Select the mode with the { / B buttons. NOTE: · There are 3 modes for the screen saver; "Off", "Slow", and "Fast". "Slow" moves 1 pixel every 5 minutes and "Fast" moves 1 pixel every minute. This prevents images burning into the screen. DISPLAY K MENU PREVIOUS MENU { SLEEP PREVIOUS B 5 Press the PREVIOUS button to return to the MAIN MENU screen. NOTE: · Pressing the MENU button cancels the menu. L Screen saver prevents the display from being etched by an unchanging image. You can specify a setting for it. 1 2 3 Enter the main menu with the MENU button. Select "Detail" on the MAIN MENU screen with the K / L buttons. Press the B (ENTER) button. The "DETAIL" menu is displayed on the screen. NOTE: · Press the PREVIOUS button to return to the MAIN MENU. Pressing the MENU button cancels the menu. 16 EXTERNAL INPUT TERMINALS The following input terminals are available. In order to view television, it is necessary to connect a tuner device (example: cable box, satellite box, DTV, etc.) to the plasma display. R AUDIO L VIDEO2 S-VIDEO2 AV Input Terminals VIDEO2 S-VIDEO2 See page 18. AU D I O AUDIO OUT L R R AUDIO L VIDEO1 S-VIDEO1 R COMPONENT 1 L Y Pb Pr COMPONENT 2 R L Y Pb Pr INNER JACKS INNER JACKS Audio Output Terminals AUDIO OUT See page 20. AV Input Terminals VIDEO1 S-VIDEO1 See page 18. Component Input Terminals COMPONENT 1 COMPONENT 2 See page 19. 17 OPERATING THE PLASMA DISPLAY / EXTERNAL INPUT TERMINALS EXTERNAL INPUT TERMINALS CONNECTING DEVICES TO THE AV INPUT TERMINALS Connect the output of the device to the input terminals of plasma display as shown in the following illustrations. NOTE: · You can select TV channels with the VCR or Cable/Satellite set top box of the program you see. · Cables shown here are not included with the plasma display. VIDEO Signal Connection (Basic Signal Transfer) Example of input signal source (DVD Player) (VCR) Antenna or cable signal Antenna, cable, satellite signal Video input to VIDEO jack Audio input to L/R jacks R AUDIO L VIDEO2 S-VIDEO2 (Cable/Satellite STB) (Camcorder) AUDIO-VIDEO 3×RCA audio video cables R Audio OUT L Video OUT S Video OUT Audio input to L/R jacks Video input to VIDEO jack AUDIO R L VIDEO1 S-VIDEO1 S-VIDEO Signal Connection (Better Signal Transfer) Example of input signal source (DVD Player) (VCR) Antenna or cable signal Antenna, cable, satellite signal Video input to S-VIDEO jack Audio input to L/R jacks R AUDIO L VIDEO2 (Cable/Satellite STB) S-VIDEO2 S-VIDEO (Camcorder) AUDIO Audio input to L/R jacks Video input to S-VIDEO jack 2×RCA audio cables R Audio OUT L Video OUT S Video OUT AUDIO R L VIDEO1 S-VIDEO1 18 CONNECTING DEVICES TO THE COMPONENT INPUT TERMINALS Connect the output of the device to the input terminals of the plasma display as shown in the following illustrations. NOTE: · Cables shown here are not included with the plasma display. Component Signal (Y, Cb/Pb, Cr/Pr) Connection (Best Signal Transfer) 480i, 480p (progressive), 1080i and 720p (progressive) signals can be connected. (Example: DVD Player) R L Y CB/PB CR/PR 3×RCA video cables Y, Cb/Pb, Cr/Pr AUDIO 2×RCA audio cables AU D I O R L Y Pb Pr (Example: Set Top Box for DTV) Antenna, cable, satellite signal COMPONENT 1 COMPONENT 2 R INNER JACKS L Y Pb Pr Y PB