User manual SYMPHONIC WF20D4

OWNER'S MANUAL COLOR TV/DVD WF20D4 (20 inch) SUPPLIED ACCESSORIES Remote Control Unit Batteries Owner's Manual Owner's Manual INSTRUCCIONES EN ESPAÑOL INCLUIDAS. As an ENERGY STAR ® Partner, our company has determined that this product meets the ENERGY STAR ® guidelines for energy efficiency. ENERGY STAR ® is a U.S. registered mark. NE228UD 2 AA Batteries 1EMN20057 If you need additional assistance for set-up or operating after reading owner's manual, please call TOLL FREE : 1-800-242-7158. Or visit our WEB SITE at http://www.funai-corp.com Please read before using this equipment WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1.Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2.Retain Instructions-The safety and operating instructions should be retained for future reference. 3.Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4.Follow Instructions-All operating and use instructions should be followed. 5.Cleaning-Unplug the unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5. 6.Attachments-Do not use attachments not recommended by the unit manufacturer as they may cause hazards. 7.Water and Moisture-Do not use this unit near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8.Accessories-Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the unit. Any mounting of the appliance PORTABLE CART WARNING AVERTISSEMENT POUR UNE should follow the manufacturer's TABLE ROULANTE PORTATIVE instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appli- S3126A ance and cart combination to overturn. Accessoires- Ne placez pas cette appareil sur une table roulante, un support, un trépied, une console ou une table instable. Cette appareil risquerait de tomber, pouvant gravement blesser quelqu'un et l'appareil même pourrait être sérieusement endommagé. N'utilisez qu'une table roulante, un support, un trépied, une console ou une table recommandé par le fabriquant, ou vendu avec l'appareil. Pour n'importe quelle installation de l'appareil, on devra suivre les instructions du fabriquant et l'on devra utiliser les accessoires d'installation recommandés par le fabriquant. L'ensemble combiné de l'appareil avec une table roulante devra être déplacé avec précaution. Des arrêts brusques, une force excessive et des surfaces inégales peuvent provoquer le renversement de l'ensemble combiné de l'appareil/table roulante. 9. Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the unit and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat register. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10.Power Sources-This unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For unit's intended to operate from battery power, or other sources, refer to the operating instructions. 11.Grounding or Polarization-This unit is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. ­2­ EN 0C28 F IGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECT RICAL CODE ANTE NNA L EAD I N WI RE GROUND CLAMP A NTENNA DI SCHARG E UN I T (NEC SECTION 8 10 -2 0) EL ECT RI C SE RV I CE EQ U I PM EN T G RO UNDI NG CO NDUCT ORS (NEC SECTION 8 10 -2 1) G RO UND CL AM PS NEC - NATI O NAL EL ECTRI CAL CO DE POWER SERVI C E G RO UNDI NG EL EC TR O DE SYST EM (NEC ART 2 50 , PART H) S2 8 9 8 A 12.Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 13.Outdoor Antenna grounding-If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A) 14.Lightning-For added protection for this unit receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power-line surges. 15.Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16.Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 17.Object and Liquid Entry-Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit. 18.Servicing-Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 19.Damage Requiring Service-Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged or frayed. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation. e. If the unit has been dropped or damaged in any way. f. When the unit exhibits a distinct change in performancethis indicates a need for service. 20.Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards. 21.Safety Check-Upon completion of any service or repairs to this unit, ask the service technician to perform routine safety checks to determine that the unit is in proper operating condition. 22.Heat-This unit product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. ­3­ EN 0C28 PRECAUTIONS IMPORTANT COPYRIGHT INFORMATION Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. RADIO-TV INTERFERENCE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. LASER SAFETY This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM. LOCATION: INSIDE, NEAR THE DECK MECHANISM. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. A NOTE ABOUT RECYCLING This product's packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes. The serial number of this product may be found on the back of the unit. No other unit has the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file. Date of Purchase Dealer Purchase from Dealer Address Dealer Phone No. Model No. Serial No. ­4­ EN 0C28 LOCATION For safe operation and satisfactory performance of your unit, keep the following in mind when selecting a place for its installation: · Shield it from direct sunlight and keep it away from sources of intense heat. · Avoid dusty or humid places. · Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top or bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes. · Install unit in a horizontal position. · Avoid locations subject to strong vibration. · Do not place the unit near strong magnetic fields. · Avoid moving the unit to locations where temperature differences are extreme. SYMBOLS USED IN THIS MANUAL The following symbols below appear in some headings and notes in this manual, with the following meanings TV : Description refers to TV operation (in the TV mode). DVD-V : Description refers to playback of DVD video discs (in the DVD mode). CD : Description refers to playback of audio CDs (in the DVD mode). MP3 : Description refers to playback of MP3 discs (in the DVD mode). QUICK : Description refers to the items to be set by the QUICK mode (in the DVD mode). AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE · Do not handle the power cord with wet hands. · Do not pull on the power cord when disconnecting · · · it from an AC wall outlet. Grasp it by the plug. If by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to our Authorized Service Center for servicing. Do not put your fingers or objects into the unit disc loading tray. Do not place anything directly on top of the unit. WARNING Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place or after heating a cold room or under conditions of high humidity. If a DVD is played in a unit which has moisture, it may damage the DVD and the unit. Therefore when the condensation occurs inside the unit, turn POWER on and allow at least 2 hours for the unit to dry out. ­5­ EN 0C28 TABLE OF CONTENTS C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2 C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4 LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .5 WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 SYMBOLS USED IN THIS MANUAL . . . . . . .5 C TABLE OF CONTENTS . . . . . . . . . . . . . . . . . .6 C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 C OPERATING CONTROLS AND FUNCTIONS . . .8 INSTALLING THE BATTERIES . . . . . . . . . . .9 C PREPARATION FOR USE . . . . . . . . . . . . . . .10 ANTENNA/CABLE CONNECTIONS . . . . . . .10 CONNECTING TO EXTERNAL INPUT JACKS .11 CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL INPUT JACKS, MD DECK OR DAT DECK (for DVD only) . .11 CONNECTING TO A DOLBY DIGITAL DECODER (for DVD) . . . . . . . . . . . . . . . . . . .12 TV SECTION C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .13 SELECTING THE LANGUAGE . . . . . . . . . . .13 CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . .13 DELETING (OR ADDING) CHANNEL(S) . . .14 C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .15 WATCHING A TV PROGRAM . . . . . . . . . . . .15 DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15 PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15 SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .16 CLOSED CAPTION SYSTEM . . . . . . . . . . . .16 V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .17 DVD SECTION C ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . .19 PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . .19 DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . .19 C PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . .20 BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . .20 GENERAL FEATURES . . . . . . . . . . . . . . . . . .20 DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . .20 TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . .20 RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 STEP BY STEP PLAYBACK . . . . . . . . . . . . .21 FAST FORWARD/REVERSE SEARCH . . . . .21 SLOW FORWARD / SLOW REVERSE . . . . .21 C SEARCH FUNCTION . . . . . . . . . . . . . . . . . .22 TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . .22 TITLE / CHAPTER SEARCH . . . . . . . . . . . . .22 TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . .22 MARKER SETUP SCREEN . . . . . . . . . . . . . .22 C SPECIAL PLAYBACK FUNCTION . . . . . . . .23 REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .23 RANDOM PLAYBACK . . . . . . . . . . . . . . . . .23 C PLAYING A MP3 DISC . . . . . . . . . . . . . . . . . .24 MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . .24 REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .24 RANDOM PLAYBACK . . . . . . . . . . . . . . . . .24 C CHANGING THE SETTINGS . . . . . . . . . . . .25 SUBTITLE LANGUAGE . . . . . . . . . . . . . . . .25 AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . .25 STEREO SOUND MODE . . . . . . . . . . . . . . . .25 CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . .25 BLACK LEVEL SETTING . . . . . . . . . . . . . . .25 VIRTUAL SURROUND . . . . . . . . . . . . . . . . .25 C THE ON-SCREEN INFORMATION . . . . . . .26 C CHANGING THE DVD SETUP ITEMS . . . .27 LANGUAGE SETTING . . . . . . . . . . . . . . . . .27 DISPLAY SETTING . . . . . . . . . . . . . . . . . . . .28 AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . .28 PARENTAL CONTROL . . . . . . . . . . . . . . . . .29 INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . .29 C TROUBLESHOOTING GUIDE . . . . . . . . . . .30 C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .32 DISC HANDLING . . . . . . . . . . . . . . . . . . . . . .32 C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .33 C ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover ­6­ EN 0C28 FEATURES TV Mode DVD Mode ¡Dolby Digital sound · 181 channel capability PLL frequency synthesiz· · er tuner with direct station call (A converter may be necessary to view scrambled cable channels.) Infrared remote control Trilingual on screen menu display selectable in English, Spanish or French The Sleep Timer function enables you to shut off the power without pressing POWER after a desired time period. ¡Closed Caption Decoder This unit can handle Dolby Digital surround sound having 5.1 channels when connected to a Dolby Digital decoder. ¡Still/fast/slow/step playback Various playback modes are available including still pictures, fast forward/reverse, slow motion and step frames. ¡Random playback for audio CD and MP3 ¡Sleep Timer This unit can shuffle the order of tracks to play them in random order. ¡Program playback for audio CD and MP3 You may view specially labeled (cc) TV programs, movies, news, etc. with either a dialogue caption or text display added to the program. ¡Auto Shut Off Function You can program the order of tracks to play them in any desired order. ¡DVD menus in a desired language You can display DVD menus in a desired language, if available on a DVD. ¡Screen saver/Auto power-off functions If there is no air signal input from the antenna terminal and no operation for 15 minutes, the unit will turn itself off automatically. ¡V-CHIP Enables parents to prevent their children from watching inappropriate material on TV. The screen saver program starts when there is no input from the unit for 5 minutes in the stop mode. When the screen saver program is activated for 15 minutes, the power is automatically turned off. ¡Subtitles in a desired language You can select a desired language for the display subtitles, if that language is available on a disc. ¡Selecting a camera angle You can select the desired camera angle, if a disc contains sequences recorded from different angles. ¡Choices for audio language and sound mode You can select the desired audio language and sound mode, if different languages and modes are available on a disc. ¡Parental lock You can set the control level to limit playback of discs which may not be suitable for children. ¡Automatic detection of discs This unit automatically detects if the loaded disc is DVD, audio CD or MP3 on disc. ¡On-screen display Information about the current operation can be displayed on a TV screen, allowing you to confirm the currently active functions (such as program playback), on the TV screen using the remote control. ¡Search Chapter search / Title search / Track search / Time search ¡Repeat Chapter / Title / Track / Group / All / A-B ¡Marker The part designated by user can be called back. ¡Resume Play User can resume to playback from the part at which the play was stopped. ¡Virtual Surround ¡Bit rate indication ¡DRC (Dynamic range control) You can control the range of sound volume. ­7­ EN 0C28 OPERATING CONTROLS AND FUNCTIONS TV/DVD FRONT PANEL [Fig. 1] VIDEO L­AUDIO­R POWER VOLUME CHANNEL STOP SKIP PLAY SKIP OPEN/ PAUSE CLOSE ­SEARCH­ HEADPHONE 1 2 3 4 5 6 7 8 9 10111213 14 REMOTE CONTROL [Fig. 2] 7. Remote Sensor Window 8. STOP Button [page 20] Stops operation of the disc. POWER PICTURE SELECT OPEN/ CLOSE 4 36 16 1 4 7 SLEEP 2 5 8 0 SKIP 3 CH. 13 34 6 6 9 +100 VOL. 17 9 11 10 5 35 19 18 8 33 32 31 30 29 9. SKIP H Button [page 21] Plays back from the beginning of the current chapter or track. SEARCH (REV) E Button (Front Panel) [page 21] During playback or in the pause mode, press and hold button down for a few seconds to change reverse playback speed. 10. PLAY Button [page 20] Starts playback of the disc contents. Press to change to DVD mode when TV mode. +10 V.SURR MUTE PLAY REV STOP PAUSE SLOW DISC MENU FWD 12 DISPLAY 23 20 21 22 15 24 25 ENTER SETUP TITLE RETURN CLEAR SEARCH MODE REPEAT A-B 11. SKIP G Button [page 21] Plays back from the beginning of the next chapter or track. SEARCH (FWD) D Button (Front Panel) [page 21] During playback or in the pause mode, press and hold button down for a few seconds to change forward playback speed. 12. PAUSE Button [page 21] Pauses the current disc operation. 13. OPEN/CLOSE Button [page 20] Press to insert discs into or remove them from the tray. 14. HEADPHONE Jack To connect headphone (not supplied) for personal listening. 15. MODE Button [pages 23-25] Activates program playback or random playback mode when playing CDs or MP3. 16. Number Buttons TV Mode: [page 15] Press two digits to directly access the desired channel. Remember to press 0 before a single digit channel. +100 Button Press to select cable channels which are higher than 99. DVD Mode: [page 22] Press to enter the desired number. +10 Button Press to enter the desired numbers which are greater than 9. MODE AUDIO SUBTITLE ANGLE 28 27 26 1. Disc loading tray 2. VIDEO input Jack [page 11] Connect to the video output jack of a video camera or VCR. 3. AUDIO L/R input Jacks [page 11] Connect to the audio output jacks of a video camera or VCR. 4. POWER Button [page 13] Press to turn the power on and off. 5. VOLUME K/L (VOL. m/n) Buttons Press to control the volume level for the DVD and TV. 6. CHANNEL K/L (CH. K/L) Buttons [page 14] Press to select memorized channel. Press to change to TV mode when DVD mode. ­8­ EN 0C28 TV/DVD REAR VIEW [Fig. 3] COAXIAL ANT. 37 17. SLEEP Button [page 16] Press SLEEP to display the sleep timer and start the function. The shut off time can be determined by the number of times you press this button. (0, 30, 60, 90 or 120 minutes) 18. REV h Button [page 21] Press to view the DVD picture in fast reverse motion. Press PAUSE, then press this button to begin slow motion playback. Press this button repeatedly to change the reverse speed of slow motion. FWD g Button [page 21] Press to fast forward the Disc. Press PAUSE, then press this button to begin slow motion playback. Press this button repeatedly to change the forward speed of slow motion. 19. V.SURR (VIRTUAL SURROUND) Button 38 39 Press to accept a setting. 32. Arrow Buttons TV Mode: [page 13] Press to select a setting mode from the menu on the TV screen. Press to select or adjust from a particular menu. DVD Mode: [page 20] Use when making settings while watching the display on a TV screen. 33. DISC MENU Button [page 20] Displays the menus in the DVD. 34. SELECT Button [page 20] Press to change to TV mode, external input mode or DVD mode. NOTE: When you select the DVD mode by this button, press PLAY or OPEN/CLOSE first. Otherwise, the DVD features are not operated. [page 25] Press to set virtual surround on/off. 20. SETUP Button [pages 13,27-29] Press to enter or exit the TV menu or DVD setup mode. 21. TITLE Button [page 20] Displays the title menu. 22. CLEAR Button [pages 22-24] Resets a setting. 23. DISPLAY Button TV Mode: Press to display the channel number on the screen. If you press it again, the channel number will disappear. DVD Mode: [page 26] Displays the current status on the TV screen for checking purposes. 24. SEARCH MODE Button [page 22] Press to locate a desired point. 25. AUDIO Button [page 25] Press to select a desired audio language or sound mode. 26. SUBTITLE Button [page 25] Press to select a desired subtitle language. 27. REPEAT Button [page 23] Repeats playback of the current disc, title, chapter, group or track. 28. ANGLE Button [page 25] Press to change the camera angle to see the sequence being played back from a different angle (if available). 29. REPEAT A-B Button [page 23] Repeats playback of a selected section. 30. RETURN Button [page 25] Returns to the previous operation in the DVD setup mode. 31. ENTER Button [pages 13, 20] 35. MUTE Button Press MUTE to turn off the sound portion of the TV program. (Volume level display turns LIGHT RED from LIGHT BLUE.) Press MUTE again or press VOL. m or nto restore sound. 36. PICTURE Button [page 15] Press to enter picture adjustment mode. 37. Power cord Connect to a standard AC outlet (120V/60Hz). NOTE: Remove the power cord from the hook to avoid breaking a wire before you connect to a standard AC outlet. 38. COAXIAL digital audio out Jack (DVD Audio Only) [pages 11, 12] Connect to the digital input of an external amplifier or decoder. 39. ANT. in Jack Connect to an antenna, cable system or satellite system. INSTALLING THE BATTERIES 1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow. 2)Insert 2 "AA" penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings. 3)Replace the cover. NOTES: ¡Do not mix alkaline and manganese batteries. ¡Do not mix old and new batteries. ­9­ EN 0C28 PREPARATION FOR USE ANTENNA/CABLE CONNECTIONS Satellite Box or Cable Box OUT (Not supplied) IN From Cable System or Satellite Dish VHF/UHF Antenna (Not supplied) VHF Antenna (Not supplied) From Cable System COAXIAL ANT. UHF Antenna (Not supplied) VHF/UHF or Combiner (Not supplied) or 75-ohm Coaxial Cable (Not supplied) ANT. or Note to CATV system installer: Flat twin-lead cable [Fig. 4] This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. Bent pin NOTE: Before plugging the antenna into the ANT. IN jack of the unit, check that the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the ANT. IN jack of the unit. Cable Plug (Needs to be straightened)(Straight pin) VHF/UHF COMBINED ANTENNA A VHF UHF 75 ohm combination antenna can be connected to ANT terminal. CABLE WITH CONVERTER/DESCRAMBLER BOX OR SATELLITE BOX If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic connection shown here. Channel selection must be made with the converter box or satellite box. This means that channels cannot be changed using the TV/ DVD Remote Control. TO VIEW A SCRAMBLED/UNSCRAMBLED CHANNEL 1.Set the TV/DVD channel selector to the output channel of the Cable Converter Box or Satellite Box. (Ex. CH3) 2.Select the channel to view on your Cable Converter Box or Satellite Box. VHF/UHF SEPARATE ANTENNAS In some areas it will be necessary to use an outdoor antenna. CABLE WITHOUT CONVERTER/ DESCRAMBLER BOX Use this connection if your cable system connects directly to your unit without a converter box. Use the TV/ DVD Remote Control to select channels. ­ 10 ­ EN 0C28 CONNECTING TO EXTERNAL INPUT JACKS When you watch a program recorded on another source (VCR or video camera), use the audio/video input jacks on the front of the unit. Connect the audio/video output jacks of another source to the AUX AUDIO L/R and VIDEO jacks of this unit. Then press SELECT until "AUX" appears on the screen. NOTE: · When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the monaural VCR (another source) to the AUDIO L jack of this unit. The audio will output in both L and R channel equally. [Front of the TV/DVD] To the [Another source] audio output jacks VIDEO L­AUDIO­R Audio/Video cables (not supplied) etc. To the video output jack VIDEO L­AUDIO­R [Fig. 5] CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL INPUT JACKS, MD DECK OR DAT DECK (for DVD only) Use an audio coaxial digital cable available at retail for the audio connections. Amplifier equipped with digital input jacks, MD deck, DAT deck, etc. COAXIAL ANT. To COAXIAL DIGITAL AUDIO INPUT jack To DIGITAL AUDIO OUT (PCM/BITSTREAM) COAXIAL jack (only DVD AUDIO OUT) [Fig. 6] NOTES: · The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound by an MD or DAT deck. · Be sure to turn off the power to all components in the system before connecting another component. · Refer to the Owner's Manuals for the components to be connected to the unit. · Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD using incorrect settings may generate noise distortion and may also damage the speakers. (Refer to page 28 to set DOLBY DIGITAL to OFF.) ­ 11 ­ EN 0C28 CONNECTING TO A DOLBY DIGITAL DECODER (for DVD) If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, it outputs a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the unit up to a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound as enjoyed in movie theaters. Use audio coaxial digital cables available at retail for the audio connections. Front speaker (left) Center speaker Front speaker (right) COAXIAL ANT. Dolby Digital decoder To COAXIAL DIGITAL AUDIO INPUT jack Surround speaker (right) Subwoofer To DIGITAL AUDIO OUT (PCM/BITSTREAM) COAXIAL jack Surround speaker (left) [Fig. 7] NOTES: · Be sure to turn off the power to all components in the system before connecting another component. · Refer to the Owner's Manuals for the components to be connected to the unit. · If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode. (Refer to page 28 to set DOLBY DIGITAL to ON.) · Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD using incorrect settings may generate noise distortion and may also damage the speakers. Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. ­ 12 ­ EN 0C28 TV SECTION SET UP FOR USE SELECTING THE LANGUAGE TV CHANNEL SET UP TV You can program the tuner to scan all the channels you receive in your area. NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the unit channel selector to the output channel of the cable box or satellite box (Ex CH3), then select the channel to be viewed on the Cable Box or Satellite Box. Make sure ... · Press POWER to turn on the unit. 1 Plug in the TV/DVD power cord Plug the unit power cord into a standard AC outlet. NOTE: · If any digits appear in the corner of the screen, press POWER without unplugging the power cord. Make sure ... · Press POWER to turn on the unit. NOTE: This function effects only the language on the screen menu and not the audio source. 1 2 Select "LANGUAGE" - TV SETUP - Select "CHANNEL SET UP" - TV SETUP B CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] Press SETUP on the remote control. Press Arrow (K/L) to point to "LANGUAGE". CHANNEL SET UP V-CHIP SET UP B LANGUAGE [ENGLISH] CAPTION [OFF] Press SETUP on the remote control. Press Arrow (K/L) to point to "CHANNEL SET UP". Then press ENTER. 3 Select "ENGLISH", "ESPAÑOL" or "FRANÇAIS" 2 Begin auto ch programming ­ CHANNEL SET UP ­ ADD / DELETE CH (CATV) B AUTO CH PROGRAMMING Select "ENGLISH", "ESPAÑOL"= Spanish or "FRANÇAIS"= French using ENTER. 4 Exit the Language mode Press SETUP to return to TV mode. NOTE: If for some reason the menu is in Spanish or French, press SETUP, press Arrow (K/L) to point to "IDIOMA [ESPAÑOL]" or "LANGAGE [FRANÇAIS]", then press ENTER, then press SETUP on the remote control. Press Arrow (K/L) to point to "AUTO CH PROGRAMMING". Then press ENTER. The tuner scans and memorizes all the active channels in your area. 3 After scanning The tuner stops on the lowest memorized channel. · When AUTO CH PROGRAMMING is activated where there is no TV signal input, "NO TV SIGNALS" will appear on the display after the completion of the channel scanning. · The unit may recognize TV channels to be CATV channels by the receiving conditions. In this case, try auto ch programming again after checking antenna connection. ­ 13 ­ EN 0C28 DELETING (OR ADDING) CHANNEL(S) TV The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.) 1 Select "CHANNEL SET UP" - TV SETUP B CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] Press SETUP on the remote control. Press Arrow (K/L) to point to "CHANNEL SET UP". Then press ENTER. 2 Select "ADD/DELETE CH" ­ CHANNEL SET UP ­ B ADD / DELETE CH (CATV) AUTO CH PROGRAMMING Press Arrow (K/L) to point to "ADD/DELETE CH". Press ENTER. 3 Enter the desired channel number Press Arrow (K/L) until your desired channel number appears. 08 (You can also use the number buttons or CHANNEL(CH.) K/L to enter it) (Example: CH8) · You must precede single-digit channel numbers with a zero (Example: 02 ... 09). · When selecting cable channels which are higher than 99, press +100 first, then press the last two digits. (Example: to select channel 125, first press +100, then press 2 and 5). ADD / DELETE 4 Delete (or add) it from (or into) memory Press ENTER. The channel number changes to light red. The channel is deleted from memory. · To delete another channel, repeat steps [3] and [4]. · If you press ENTER again, the channel is memorized again. Added channel: Light blue. Deleted channel: Light red. 5 Exit the channel setup mode Press SETUP to return to TV mode. NOTE: To confirm that channel(s) has been deleted or added, press CHANNEL(CH.) K/L. ­ 14 ­ EN 0C28 TV OPERATION WATCHING A TV PROGRAM TV PICTURE CONTROL TV The unit's picture controls ­ BRIGHT, CONTRAST, COLOR, TINT and SHARPNESS ­ are preset to factory specifications. Although they are usually the best, you may need to make some further adjustments for a more natural looking image. Make sure ... · The unit is turned on. 1 2 Turn on the TV/DVD Press POWER to turn on the unit. Select the channel number Press CHANNEL(CH.) K/L to select your desired channel number or press the number buttons. Notes for using the number buttons on the remote control: · You must precede single-digit channel numbers with a zero (Example: 02 ... 09). · When selecting cable channels which are higher than 99, press +100 first, then press the last two digits. (Example: to select channel 125, first press +100, then press 2 and 5). Remember: ¡If the unit is connected to a cable box or satellite box, it must be on CH3 or CH4, then the channel to be viewed must be selected on the cable box or satellite box. 1 Select "PICTURE CONTROL" Press PICTURE on the remote control. 2 Select item you want to adjust 3 Adjust sound Press Arrow (K/L) until desired control is displayed. BRIGHT CONTRAST COLOR TINT SHARPNESS BRIGHT ­PPPPPPPCPPPPPPP+ Y Press VOLUME(VOL.) X/Y to adjust the volume. VOLUME 20 3 C CC C C C CCCCCCCCCC Adjust the picture control NOTE: · If you press CHANNEL(CH.) K/L in the DVD mode, you can change the TV channels. Even if you turn off the unit in the DVD mode, when you turn it on again, it will go into the TV mode. Press Arrow (s / B) to adjust to your desired level within 5 seconds. NOTE: · At step [3], the picture adjustment display will disappear from the TV screen after about 5 seconds unless you press any buttons, even though you may not be finished. In this case, repeat from step [1]. s to decrease brightness to decrease contrast to pale to purple to soft B to increase brightness to increase contrast to brilliant to green to clear DEGAUSSING Magnetism from nearby appliances and speakers might affect the color of the TV picture. If this happens, move this unit away from the appliance. If the color is still not correct, disconnect power cord from AC outlet then reconnect it after 30 minutes. BRIGHT CONTRAST COLOR TINT SHARPNESS · If there is a power failure of any kind, the unit will retain its memory for this feature. ­ 15 ­ EN 0C28 SLEEP TIMER TV The Sleep Timer function enables you to shut off the power without pressing POWER after a desired time period. NOTE: If the unit displays a black box on the TV screen, this means that the unit is set to the TEXT mode. To clear screen, select [CAPTION1], [CAPTION2] or [OFF]. Make sure ... · The unit is turned on. 1 Set "SLEEP TIMER" Press SLEEP on the remote control. You may change the sleep time with pressing SLEEP repeatedly. The timer is set up to 120 minutes, 30 minutes each time SLEEP is pressed. 1 SLEEP 120 MINUTE Select "CAPTION" - TV SETUP - Press SETUP on the remote control. Press K or L to point to "CAPTION". CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] B CAPTION [OFF] To cancel the sleep timer: Press SLEEP repeatedly until "SLEEP 0 MINUTE" is displayed. NOTES: · When you disconnect the unit from the AC outlet, or if you have a power failure, the sleep time will be lost. · To view the time left for sleep timer press SLEEP once when SLEEP display disappears. After 10 seconds, display will disappear again. 2 Select your desired caption menu - TV SETUP - Press ENTER until your desired caption menu appears. ([CAPTION1], [CAPTION2], [TEXT1] or [TEXT2]) CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] B CAPTION [CAPTION1] 3 Exit the caption setting mode CLOSED CAPTION SYSTEM TV You can view specially labeled (cc) TV programs, movies, news, etc. with either a dialogue caption or text display. CAPTION mode: By choosing the caption mode, you can watch dramas, movies and news while captioning the dialogues and the contents of news. TEXT mode: By choosing the text mode, you can watch half screen text information if you want. 1-2: You may get these captions or text information by selecting either "1" or "2". Caption "2" is used, usually for a second language if available. Press SETUP to return to TV mode. TO CANCEL THE CLOSED CAPTION SYSTEM Repeat steps [1] to [2], select [OFF] using ENTER. Press SETUP on the remote control to return to TV mode. WHEN THE CLOSED CAPTION MODE IS ON The On-Screen Display will disappear after 5 seconds. · This is also true when MUTE is pressed. · If there is a power failure of any kind, the unit will retain its memory for this feature. NOTE: Not all programs are broadcast with closed captions. Your television is designed to provide error free closed captions from high quality antenna, cable and VCR signals. Conversely, poor quality signals are likely to result in caption errors or no captions at all. Common signal conditions which may cause captions errors are listed below: · Automobile ignition noise · Electric motor brush noise · Weak snowy reception on TV screen · Multiplex signal reception displaying picture ghosts or airplane flutter. ­ 16 ­ EN 0C28 V-CHIP SET UP TV V-CHIP enables parents to prevent their children from watching inappropriate material on TV. V-CHIP reads the ratings for programming (except for news and sports programs, unedited movies on premium cable channels and Emergency Broadcast System signals), then denies access to programming if the program's rating meets the limitations you select. In this case, "PROTECTED PROGRAM by ..." message appears on the TV screen. To block ratings, follow the steps below. · Programming may be rated by the Motion Picture Association of America (MPAA) or according to the Television Parental Guidelines. In order to block any inappropriate programming, set your limits in both places (MPAA RATING and TV RATING). · When you select a rating category and set it to · [BLOCK], the higher rating will change to [BLOCK] automatically. Also, the lower rating will change to [VIEW] automatically. When you set "TV-Y" to [VIEW], all ratings will change to [VIEW] automatically. Selection TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA Rating Category Explanations Appropriate for all children Appropriate for children seven and older General Audience Parental Guidance suggested. Unsuitable for children under 14 Mature audience only TV RATING SET UP Make sure ... · The unit is turned on. 1 Select "V-CHIP SET UP" - TV SETUP - Press SETUP on the remote control. Press Arrow (K/L) to point to "V-CHIP SET UP". Then press ENTER. CHANNEL SET UP B V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] 2 Input Access code ACCESS CODE Press the number buttons to enter 4digit access code. The default code is 0000. ____ 3 Select "TV RATING" B ­ V-CHIP SET UP ­ TV RATING MPAA RATING CHANGE CODE Press Arrow (K/L) to point to "TV RATING". Then press ENTER. When you select TV-Y7, TV-PG, TV-14 or TV-MA and you press ENTER, the sub-ratings will appear on the TV screen. If you select the rating category (example: TV-PG) and turn it [BLOCK] or [VIEW], the sub-ratings (example: V for Violence) will turn [BLOCK] or [VIEW] automatically. You can set the sub-ratings to [BLOCK] or [VIEW] individually when the rating category is set to [BLOCK]. To set the sub-ratings individually, follow the steps below. · When you select [TV-Y7]: Press Arrow (K/L) to select "FV" (Fantasy Violence). Then press ENTER to select [BLOCK] or [VIEW]. · When you select [TV-PG], [TV-14] or [TV-MA]: Press Arrow (K/L) to select "D"(Suggestive Dialog), "L"(Coarse Language), "S"(Sexual Situation) or "V"(Violence). Then press ENTER to select [BLOCK] or [VIEW]. NOTE: When you select [TV-MA], "D" does not appear on the TV screen. · The sub-ratings which are set to [BLOCK] appears next to the rating category in the TV RATING menu. TV­Y7 [BLOCK] B FV [BLOCK] TV­PG [BLOCK] BD L S V [BLOCK] [BLOCK] [BLOCK] [BLOCK] B TV­Y TV­Y7 ( ) TV­G TV­PG (DLSV ) TV­14 (DLSV ) TV­MA ( LSV ) [VIEW] [VIEW] [VIEW] [BLOCK] [BLOCK] [BLOCK] 4 Select your desired item B TV­Y TV­Y7 ( TV­G TV­PG ( TV­14 ( TV­MA ( ) ) ) ) [VIEW] [VIEW] [VIEW] [VIEW] [VIEW] [VIEW] Press Arrow (K/L) to point to your desired item. Then press ENTER to select [BLOCK] or [VIEW]. 5 Exit the V-Chip setting mode Press SETUP on the remote control to return to original mode. ­ 17 ­ EN 0C28 MPAA RATING SET UP Make sure ... · The unit is turned on. CHANGE ACCESS CODE To change access code, follow the steps below. 1 1 Select "V-CHIP SET UP" - TV SETUP CHANNEL SET UP B V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] Select "V-CHIP SET UP" - TV SETUP CHANNEL SET UP B V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] Press SETUP on the remote control. Press Arrow (K/L) to point to "VCHIP SET UP". Then press ENTER. Press SETUP on the remote control. Press Arrow (K/L) to point to "VCHIP SET UP". Then press ENTER. 2 Enter 4-digit access code ACCESS CODE 2 Enter 4-digit access code ACCESS CODE Press the number buttons. The default code is 0000. ____ Press the number buttons. The default code is 0000. ____ 3 Select "MPAA RATING" B ­ V-CHIP SET UP ­ TV RATING MPAA RATING CHANGE CODE 3 Select "CHANGE CODE" B ­ V-CHIP SET UP ­ TV RATING MPAA RATING CHANGE CODE Press Arrow (K/L) to point to "MPAA RATING". Then press ENTER. Press Arrow (K/L) to point to "CHANGE CODE". Then press ENTER. 4 Select your desired item G PG PG­13 BR NC­17 X [VIEW] [VIEW] [VIEW] [BLOCK] [BLOCK] [BLOCK] 4 Enter 4-digit access code NEW CODE ____ Press Arrow (K/L) to point to your desired item. Then press ENTER to select [BLOCK] or [VIEW]. Selection G PG PG-13 R NC-17 X Rating Category Explanations General Audience Parental Guidance suggested. Unsuitable for children under 13 Restricted; under 17 requires accompanying parent or adult guardian No one under 17 admitted Mature audience only Press the number buttons to enter your desired access code in the NEW CODE space. Then enter the same code in the CONFIRM CODE space. V-CHIP SET UP screen will appear on the screen. · If you enter wrong code, repeat step [4], making sure you enter the same new code exactly in the confirm code space. CONFIRM CODE ____ 5 Exit the V-Chip setting mode Press SETUP on the remote control to return to original mode. NOTE: · If you unplug the power cord or a power failure occurs, the changed access code will be lost and will return to default (0000). Change your access code again as necessary. · When you select the rating category and set it to · [BLOCK], the higher rating will change to [BLOCK] automatically. Also, the lower rating will change to [VIEW] automatically. When you set "G" to [VIEW], all ratings will change to [VIEW] automatically. 5