Tandberg 220/420LTO Half Height LTO1 and LTO2 Tape Drive Quick Installation Guide Revision 4 ­ February 2006 Mechanical Installation For mechanical mounting specifications, please refer to Figure 1. Allowed mounting position is either horizontal with the indicator LEDs to the right, or vertical with the LEDs up. The drive occupies a half-size 5.25-inch slot with standard holes for mounting screws on both sides of the drive chassis and at the bottom of the drive. Figure 1 Important! Mounting screw requirements · · · · · · Mounting specifications Only M3 (metric) screws must be used for mounting the drive Maximum permitted screw penetration: 2.5 mm Minimum required screw penetration: 2.0 mm Screw torque, mounting screws: 0.5 Nm Screws are supplied with all the Tandberg 220/420LTO drive variants Bags with 4 screws and 4 SCSI ID jumpers are available (Ordering no. 43 32 65) Do not use longer screws or higher screw torque than specified! Figure 2 Allowed mounting orientations 2 SCSI Identification Make sure that the drive unit has the proper SCSI-ID before it is connected to a computer system. Refer to manuals for host computer and application software to obtain the correct ID. For correct mounting of ID-jumpers at the rear of the drive, please refer to Figure 3 and Table 1. External drives have a thumb-wheel switch to set the SCSI-ID (see Figure 6). Power Connector Service Connector SCSI Connector Figure 3 The factory default drive number setting is SCSI ID = 2. If the drive has to be set up with a different unit number, the jumpers (on the Service Connector) have to be connected according to Table 1. Example: SCSI ID = 3 Drive connectors SCSI ID=0 SCSI ID=1 SCSI ID=2 SCSI ID=3 SCSI ID=4 SCSI ID=5 SCSI ID=6 SCSI ID=7 SCSI ID=8 SCSI ID=9 SCSI ID=10 SCSI ID=11 SCSI ID=12 SCSI ID=13 SCSI ID=14 SCSI ID=15 Table 1 Service Connector jumper settings for SCSI ID (Dark = Jumper mounted) 3 SCSI Cable Host SCSI-bus Internal Terminator Connector Last SCSI Device 10 cm Figure 4 SCSI cable (Ordering no. 43 20 51) (Ordering no. 43 20 53) (Ordering no. 43 26 17) (Ordering no. 43 32 64) · Internal SCSI-LVD/SE-cable with 5 connectors · Internal, removable SCSI-LVD/SE-terminator · External, removable SCSI-LVD/SE-terminator · External SCSI 68HD/VHDCI 320MBs-cable Termination The SCSI-bus cable must be terminated in both ends according to SCSI specifications. If the tape drive is the last device on the bus, the bus must be terminated within 10 cm of the tape drive connection. Tandberg 220/420LTO has a combined SCSI-LVD/SE interface embedded. The PC-98 Specification specifies that the termination of the SCSI-bus system is a part of the SCSI-cable and not a part of the SCSI-device. As a result, termination cannot be turned on or off directly on the tape drive itself. For internal devices, a SCSI-cable with an integrated terminator or a separate terminator applied to the end connector of the cable, 10 cm from the last device, must be used. External devices must be terminated with an external terminator on the last device on the SCSI-bus. Software Installation For Software Application support and software drivers, please see www.tandberg.com. Then select SUPPORT and Select Product. For installation of Backup Application software, refer to the software vendor's software application user guide supplied with the software or on the software vendor's web. 4 Front LED Indicators Figure 5 Light Emitting Diodes (LED) Drive State READY LED (Green left) ACTIVITY LED (Green) CLEAN LED (Amber) FAULT LED (Amber right) LED-test. The LEDs are turned ON one-by-one. Power-On Self-Test starts in parallel with the LED-test . Cartridge not loaded. Cartridge loaded, no activity Cartridge loaded, activity Cleaning Cartridge loading or unloading Unrecoverable drive failure Over temperature Media Error (wrong, write protected or harmed media) ON ON ON ON OFF ON ON OFF OFF ON / OFF OFF OFF OFF OFF Flashing Flashing Flashing OFF OFF Flashing ON / OFF ON / OFF ON / OFF ON ON / OFF ON / OFF ON / OFF ON / OFF OFF OFF OFF OFF OFF Flashing ON Flashing Table 2 Front LED behavior during normal operation 5 Media and Capacities To achieve and maintain the maximum quality of your Tandberg Data tape drive, we recommend using Tandberg Data media. Drive Model Tandberg 220LTO Tandberg 420LTO LTO1, 2, 3 LTO Ultrium Generation 2 (Native format) LTO Ultrium Generation 1 (Read/Write compatible) Cleaning Cartridge for LTO1, LTO2 and LTO3 609 m 609 m 200 GByte 100 GByte 43 27 44 43 26 30 43 26 31 Media Name Tape Length 609 m Capacity (Native) 100 GByte Ordering no. 43 26 30 LTO Ultrium Generation 1 (Native format) Table 3 Media alternatives External Tabletop Enclosure ON/OFF Switch Cooling Fan SCSI_ID Switch Power Connector SCSI Interface Connectors Figure 6 External tabletop enclosure, rear side Power Requirements Tandberg 220/420LTO in external tabletop enclosure: AC Input: 100 VAC / 0.6 A or 240 VAC / 0.3 A, 50-60 Hz Tandberg 220/420LTO as standalone: DC Input (typical operation): 5 VDC / 2.1 A, 12 VDC / 0.6 A Heat Dissipation Tandberg 220/420LTO as standalone: Operating: 18 W Sleep mode with cartridge inserted: 9 W 6 Total customer satisfaction is of the utmost importance to Tandberg Data. We guarantee that this product left our premises defect free. If you are not satisfied with the quality of this product, please contact your distributor or the nearest Tandberg Data office to have the problem solved! For more documentation and information, please see our website www.tandberg.com. 7 Tandberg Data International headquarter Tandberg Data ASA, Kjelsåsveien 161, Oslo, P.O. Box 134 Kjelsås, N-0411 Oslo, Norway. Tel: +47 22 18 90 90. Fax: +47 22 18 95 50. www.tandberg.com Worldwide subsidiaries Tandberg Data Corp., 13000 Gregg Street, Poway, CA 92064, U.S.A. Tel: 858-726-1800. Fax: 858-726-1801 Tandberg Data GmbH, Feldstrasse 81, D-44141 Dortmund, Germany. Tel: +49 231 5436 0. Fax: +49 231 5436 111. Tandberg Data S.A.S., 16/18 Ave. Morane-Saulnier, F-78941 Vélizy Cedex, France. Tel: +33 1 39 26 01 01/00800-82632374. Fax: +33 1 34 65 02 89 (for technical support: 00800-07867243). Tandberg Data (Asia) Pte. Ltd, 20 Bendemeer Road, #04-05 Cyberhub, Singapore 339914, Tel: +65 6396 0786. Fax: +65 6396 0787. Tandberg Data (Japan) Inc., Eitaibashi Eco-Piazza Bldg. 8th floor 29-13, Shinkawa 1-chome, Chuo-ku Tokyo 104-033, Japan Tel: +81 3 5566 2871. Fax: +81 3 5566 2875. Tandberg Data Ltd., Bloxham Mill Business Centre, Barford Road, Bloxham, Banbury, Oxfordshire, OX15 4FF, United Kingdom Tel: +44 (0) 8450706916. Specifications subject to change without notice. All trademarks are the property of their respective owners. ©2006 Tandberg Data ASA. All Rights reserved. Part No. 433261-04. February 2006.