INSTALLING A TAPE DRIVE IN This document explains how to install or replace a tape drive in the Tandberg StorageLibrary T24 or Tandberg StorageLibrary T48. Please read the entire section that you are using prior to beginning the procedure. PREPARING FOR INSTALLATION OR REPLACEMENT Note: If your library is installed in a rack, it is not necessary to remove the library from the rack to complete this procedure. It is also not necessary to disconnect the Ethernet cable from the back of the library. Obtain these items--a #2 Phillips screwdriver and a small flat-blade screwdriver. Ensure that the environment is free of conditions that could cause electrostatic discharge (ESD)--If possible, use an antistatic mat and a grounded static protection wristband during installation. If a mat and wristband are not available, touch a known grounded surface, such as a computer's metal chassis. Warning Warnung Before performing any installation or maintenance procedures, be sure that the library's power switch is off and that the power cord is disconnected from the library and the outlet. Vor der Ausführung von Installations- oder Wartungsarbeiten ist darauf zu achten, daß der Library-Netzschalter auf "Aus" gestellt ist und daß das Anschlußkabel vom Library und der Steckdose entfernt ist. Antes de realizar cualquier procedimiento de instalación o de mantenimiento, comprobar que el interruptor de alimentación de la biblioteca está apagado y que el cable de alimentación no está enchufado ni a la biblioteca ni a la toma de corriente. Advertencia Copyright 2006 Tandberg Data and Exabyte, EZ17, M2, VXA, and VXAtape are registered trademarks; ExaBotics, MammothTape, and SmartClean are trademarks; SupportSuite is a service mark. Linear Tape-Open, LTO, the LTO Logo, Ultrium and the Ultrium Logo are trademarks of HP IBM, and Quantum in , the US and other countries. All other product names are trademarks or registered trademarks of their respective owners. 433680-01 October 2006 www.tandberg.com GENERAL INFORMATION Both the StorageLibrary T24 and StorageLibrary T48 Library accommodate Ultrium 3 (LTO-3) or Ultrium 2 (LTO-2) tape drives in half height (HH) or full height (FH) configurations. Neither library will accommodate LTO-1 tape drives. ! Important StorageLibrary T24 or StorageLibrary T48 library. Purchase tape drive kits only from Tandberg Data or Tandberg-approved suppliers. The tape drives must be specially configured (at the factory) for use in a To view this information... Installing additional tape drives Replacing a tape drive with the same configuration (half height -to- half height or full height -to- full height) Replacing a half height tape drive with a full height tape drive Reconfiguring the library (this step must be completed for the library to operate) Resuming operation Confirming the installation go to... page 8 page 14 page 19 page 25 page 26 page 28 Note: Most of the illustrations show SCSI configurations. Use the same steps to install Fibre Channel tape drives. Information that is specific to the individual libraries is indicated as follows: StorageLibrary T24--One full height tape drive or two half height tape drives StorageLibrary T48--One or two full height tape drives, or one, two, three, or four half height tape drives 2 OF 28 REFERENCE ILLUSTRATIONS StorageLibrary T24-- StorageLibrary T24 Half Height Tape Drive Cover Plate (P) Upper SCSI cover plate (S) Lower SCSI cover plate (S) StorageLibrary T24 Full Height Tape Drive Cover Plate (P) StorageLibrary T24 Full Height Fibre Channel Tape Drive Cover Plate (P) Serial cable (C) Connect to tape drive (white) Connect to library (black) ! Important Be sure to use the serial cable (C) that came with your replacement kit. The serial cables are specifically configured (at the factory) for use with the individual tape drives. 3 OF 28 Serial cable (C) Drive 2 Top serial connector (not used) Drive 1 Bottom serial connector Figure 1 StorageLibrary T24 serial cable routing--full height tape drive Serial cable (C) Drive 2 Second serial connector Bottom serial connector Drive 1 Figure 2 StorageLibrary T24 serial cable routing--half height tape drives Power cable (D) Library power connector Middle power connector (not used in this configuration) Bottom power connector Figure 3 StorageLibrary T24 power cable routing--full height tape drive Power cable (D) Top power connector (upper TD) Library power connector Middle power connector (lower TD) Figure 4 StorageLibrary T24 power cable routing--half height tape drives 4 OF 28 StorageLibrary T48-- StorageLibrary T48 Tape Drive Cover Plate (P) Half Height SCSI configuration SCSI cover plate (S) SCSI cover plate (S) StorageLibrary T48 Tape Drive Cover Plate (P) Full Height Fibre Channel configuration Serial cable (C) Connect to tape drive (white) Connect to library (black) ! Important Be sure to use the serial cable (C) that came with your replacement kit. The serial cables are specifically configured (at the factory) for use with the individual tape drives. 5 OF 28 Serial cable (C) Drive 4 Drive 3 Drive 2 Top serial connector (not used) Third serial connector (not used) Second serial connector Bottom serial connector Drive 1 Figure 5 StorageLibrary T48 serial cable routing--full height tape drives Serial cable (C) Drive 4 Drive 3 Top serial connector Third serial connector Second serial connector Bottom serial connector Drive 2 Drive 1 Figure 6 StorageLibrary T48 serial cable routing--half height tape drives 6 OF 28 Power cable (D) Library power connector Top power connector (not used in this configuration) Third power connector Second power connector (not used in this configuration) Bottom power connector Figure 7 StorageLibrary T48 power cable routing--full height tape drives Power cable (D) Library power connector Top power connector Third power connector Second power connector Bottom power connector Figure 8 StorageLibrary T48 power cable routing--half height tape drives 7 OF 28 INSTALLING ADDITIONAL TAPE DRIVES To install an additional tape drive (or tape drives), follow these steps: 1. Preparing for replacement-- a. Power off the library (press the 0 on the back of the unit) b. Disconnect the power cord, the SCSI or Fibre Channel cable(s), and the terminator (if one is installed). c. Power off the host d. Remove the tape drive cover plate (P). Set the plate and the screws aside. Back of library Tape drive cover plate (P) Power OFF (press the 0) Screws Screws Disconnect power cord Figure 9 Note: Tape drive cover plate (StorageLibrary T24 library shown) This figure shows the StorageLibrary T24 SCSI library with one half height tape drive installed. Remove the StorageLibrary T48 tape drive cover plate (SCSI and Fibre Channel) the same way. 2. Removing the internal cooling plates and disconnecting cables-- ! Important Remove as many internal cooling plates as necessary to add tape drives, but leave all empty tape drive bays covered. The plates are required for proper cooling. 8 OF 28 a. Remove the two screws (A) holding the tape drive cooling plate (B). Remove the plate, and discard it and the screws. Screws (A) Cooling plate (B) Looking inside back of library Retaining tab Single half height tape drive (cables removed for clarity) Figure 10 StorageLibrary T24 tape drive cooling plate b. Disconnect the power cables (D) from all of the tape drives. 3. Installing the tape drive-- ! Important Do not mix full height and half height or SCSI and Fibre Channel tape drives in the StorageLibrary T48 library, as it does not support mixed tape drive configurations. a. Locate the serial cable (C) that came in your replacement kit and attach it to the appropriate serial connector inside the library. StorageLibrary T24 library serial cable connections-- Half height tape drive--see Figure 2 Tape drive Half height Quantity Second tape drive Single tape drive Install in this opening... Top Bottom Serial connector Top Bottom Internal label Drive 2 Drive 1 9 OF 28 StorageLibrary T48 library serial cable connections-- Full height tape drive--see Figure 5 Half height tape drive--see Figure 6 Tape drive Quantity Fourth tape drive Half height Third tape drive Second tape drive Single tape drive Full height Second tape drive Single tape drive Install in this opening... Top Third Second Bottom Top Bottom Serial connector Top Third Second Bottom Second Bottom Internal label Drive 4 Drive 3 Drive 2 Drive 1 Drive 2 Drive 1 b. While holding the cables to the side, slide the new tape drive directly into the library, leaving it a short distance out to access the cables. Use care not to damage the cables. c. Connect the supplied serial cable (C) and the power cable (D) to the tape drives. StorageLibrary T24 tape drive serial and power cable connections-- Serial--Route the serial cable (C) over the tape drive carrier and under the power cable as shown here; connect as shown in Figure 2 (StorageLibrary T24 HH serial cable routing). Power--Route the power cable through the tape drive carriers as shown here; connect as shown in Figure 4 (StorageLibrary T24 HH power cable routing). Press the serial cable (C) down into the carrier to prevent catching it between the tape drive and the library. Power cable (D) (route under carrier and over serial cable) Serial cable (C) (route over carrier and under the power cable) Tape drive carrier Figure 11 StorageLibrary T24--installing additional tape drives: half height connectors 10 OF 28 StorageLibrary T48 tape drive serial and power cable connections-- Full height tape drive: Serial--Route the serial cable (C) under the tape drive carrier as shown here; connect as shown in Figure 5 (StorageLibrary T48 FH serial cable routing). Power--Route the power cable through the tape drive carriers as shown here; connect as shown in Figure 7 (StorageLibrary T48 FH power cable routing). Power cable (D) Route power cable through tape drive carriers Serial cable (C) Connect top FH tape drive to second internal connector. Connect bottom FH tape drive to the bottom internal connector. Figure 12 StorageLibrary T48--installing additional tape drives: full height connectors Serial cable (C) connectors Serial cable (C) Route under carrier. 11 OF 28 StorageLibrary T48 tape drive serial and power cable connections-- Half height tape drive: Serial--Route the serial cable (C) over the tape drive carrier as shown here; connect as shown in Figure 6 (StorageLibrary T48 HH serial cable routing). Power--Route the power cable through the tape drive carriers as shown here; connect as shown in Figure 8 (StorageLibrary T48 HH power cable routing). Serial connector Power connector (D) Serial cable (C) Route serial (press down into carrier cable over tape to prevent damage) drive carrier Figure 13 Installing additional tape drives--half height connectors d. Slide the tape drive the remaining distance into the library. Install the tape drives from bottom to top--fill the bottom slot first, the second slot next, and so forth. Do not skip slots. Continue adding tape drives, as needed. 12 OF 28 4. Completing the installation-- a. Locate the tape drive cover plate (see "Reference Illustrations" on page 3). First, remove the necessary SCSI plates (S), then attach the tape drive cover plate (P) with the screws you removed earlier. ! Important The library requires both the SCSI cover plates (S) and the tape drive cover plates (P) for ESD protection. Do not leave any openings uncovered. Do not connect the SCSI cables until after you reconfigure the library. If your library has... Tape drive configuration Half height Full height Quantity two one one Four Half height Three Two One Full height Two One Attach this SCSI cover plate (S)... Location None Top None None Top Top and third Top three None Top External drive label NA NA NA None Drive 4 Drive 4 and 3 Drive 4, 3, and 2 None Drive 2a Library StorageLibrary T24 Magnum448 a This applies to both SCSI and Fibre Channel library configurations. b. Reconfigure your library--You must reconfigure your library for your backup application to recognize the new tape drive. See page 25 for instructions. 13 OF 28 REPLACING A TAPE DRIVE (SAME CONFIGURATION) To replace a tape drive with a different tape drive of the same configuration (half height to half height, or full height to full height), follow these steps. 1. Preparing for replacement-- a. Power off the library (press the 0 on the back of the unit) b. Disconnect the power cord, the SCSI or Fibre Channel cable(s), and the terminator (if present) c. Power off the host d. Remove the tape drive cover plate (P). Set the plate and the screws aside. Back of library Tape drive cover plate (P) Power OFF (press the 0) Screws Screws Disconnect power cord Figure 14 Note: Tape drive cover plate (StorageLibrary T24 Fibre Channel library) This figure shows the StorageLibrary T24 Fibre Channel lib ...