INSTALLING THE IN A RACK Both the Tandberg StorageLibrary T24 and the Tandberg StorageLibrary T48 are designed for installation in a standard 4-post, 19-inch rack. The Tandberg StorageLibrary T24 uses 2 units (2U) of rack space The Tandberg StorageLibrary T48 uses 4 units (4U) of rack space ! Important Two-post racks will not support either the Tandberg StorageLibrary T24 or the Tandberg StorageLibrary T48. The rack-mount kit includes the following items: 18 ­ M5 x 12 Crest CupTM screws (black) 2 ­ sets of side support rails (left-side front and back rails and 2 ­ M3 x 8 Crest Cup screws (silver) right-side front and back rails) 8 ­ washers BEFORE YOU BEGIN Select an appropriate location--The maximum recommended ambient temperature for the library is 40° C (104° F). Install the library in an environment compatible with this temperature limit. A ventilated rack is recommended. Ensure that the work area is free from conditions that could cause electrostatic discharge (ESD). Discharge static electricity from your body by touching a known grounded surface, such as a computer's metal chassis. Ensure that the robot is "parked" and that the shipping key is in place prior to moving the library. See the Product Manual at www.tandberg.com for instructions. Obtain the following tools: #2 Phillips screwdriver Level Tape measure Copyright 2006 Tandberg Data and Exabyte, EZ17, M2, VXA, and VXAtape are registered trademarks; ExaBotics, MammothTape, and SmartClean are trademarks; SupportSuite is a service mark. Linear Tape-Open, LTO, the LTO Logo, Ultrium and the Ultrium Logo are trademarks of HP IBM, and Quantum in , the US and other countries. All other product names are trademarks or registered trademarks of their respective owners. 433679-01 October 2006 www.tandberg.com Warning Before performing any installation or maintenance procedures, be sure that the library power switch is in the off position and that the power cord is disconnected from the library and the outlet. Vor der Ausführung von Installations- oder Wartungsarbeiten ist darauf zu achten, daß der Library-Netzschalter auf "Aus" gestellt ist und daß das Anschlußkabel vom Library und der Steckdose entfernt ist. Antes de realizar cualquier procedimiento de instalación o de mantenimiento, comprobar que el interruptor de alimentación de la biblioteca está apagado y que el cable de alimentación no está enchufado ni a la biblioteca ni a la toma de corriente. Warnung Advertencia ASSEMBLING THE RAILS 1. Measure the depth of your rack--Using a tape measure, measure the inside distance from the front mounting holes of your rack to the back mounting holes. 2. Position the front and back sections of the left-side rail as shown in Figure 1, with the front rail section on top of the back rail section. Spread the sections to the distance you measured in step 1. 3. Assemble the left rail using four M5 screws, as shown in Figure 1. Keep the screws loose so that you can adjust the length of the assembled rail, if necessary. Left-side rails (viewed from front) Back flange Back section Small back flange (attach the library here in final step) Front section Front flange M5 screw (black) Figure 1 Assembling the left-side rail 2 OF 8 4. Assemble the right-side rail in the same way (see Figure 2). Right-side rails (viewed from the back) Front flange Front section Back section Back flange M5 screws (black) Figure 2 Assembling the right-side rail ATTACHING THE RAILS TO THE RACK 1. Left side rail assembly--Position the left-side rail assembly in the rack so that the front flange is behind the front screw holes in the rack (see Figure 3). Back of Rack Rack rail (back) Depth of rack (E) M5 screw (A) (black) Back flange (D) Rack rail (front) Level Front rack screw holes (B) M5 screw (A) (black) Front of Rack Front flange (C) Figure 3 Attaching the left-side rail to the rack 3 OF 8 2. Front of rack--Insert an M5 screw (A) through one of the front rack screw holes (B) and engage the pem nut in the rail flange (C). If your rack has square mounting holes or the holes are much larger than the screws provided in the kit, use a washer. Finger-tighten the screw. Insert an M5 screw (A) through a second screw hole (B) and engage the pem nut on the second screw hole in the rail flange (C). If necessary, use a washer. Finger-tighten the screw. 3. Adjust the length of the rail assembly as necessary to fit the depth of the rack (E). 4. Back of rack--Make sure the rail assembly is level, then use M5 screws (A) to attach the back flange (D) of the rail to the inside of the rack, using the same procedure as step 2. If your rack has square mounting holes or the holes are much larger than the screws provided in the kit, use a washer. Finger-tighten the screws. 5. Using a #2 Phillips screwdriver, tighten the screws securing the rails to the front and back of the rack. 6. Using a #2 Phillips screwdriver, tighten the four screws holding the rail assembly together. 7. Right side rail assembly--Repeat steps 1 through 6 for the right-side rail assembly. Make sure that the right rail assembly is at the same level as the left rail assembly. ATTACHING THE LIBRARY TO THE RAILS To attach the library to the rails: 1. From the front of the rack, place the library onto the shelf created by the rails. Tandberg StorageLibrary T24 Weight Warning-- Warning The library weighs 43 pounds (19.5 kg). Two people are needed to move or lift the library. Most of the weight is toward the back of the library. Die Library wiegt 19.5 kg Es sind mindestens 2 Personen erforderlich, um die Library zu bewegen oder zu heben. Der hintere Teil Library hat das gröte Gewicht. La biblioteca montada sobre bastidor pesa 19.5 kg Se necesitan dos personas para mover o levantar la biblioteca. La parte trasera de la biblioteca es la de mayor peso. Warnung Advertencia 4 OF 8 Figure 4 Placing the Tandberg StorageLibrary T24 on the rails Tandberg StorageLibrary T48 Weight Warning-- Warning The library weighs 69.4 pounds (31.5 kg). Two people are needed to move or lift the library. Most of the weight is toward the back of the library. Die Library wiegt 31.5 kg Es sind mindestens 2 Personen erforderlich, um die Library zu bewegen oder zu heben. Der hintere Teil Library hat das gröte Gewicht. La biblioteca montada sobre bastidor pesa 31.5 kg Se necesitan dos personas para mover o levantar la biblioteca. La parte trasera de la biblioteca es la de mayor peso. Warnung Advertencia Figure 5 Placing the Tandberg StorageLibrary T48 on the rails 5 OF 8 2. Remove the shipping key from the library. Carefully slide the library all the way back until it makes contact with the small flanges at the back of the rails (see Figure 7 and Figure 7). 3. From the back of the rack, attach the library to the rails by inserting an M3 (the two smaller screws) screw into each of the small flanges. Tighten the screws using a #2 Phillips screwdriver. Tandberg StorageLibrary T24-- Back of rack M5 x 12 (black) screws (total qty installed = 16) (total qty shipped = 18) Insert M3 x 8 screws here (one on each side) Figure 6 Attaching the Tandberg StorageLibrary T24 to the rails at the back of the rack 6 OF 8 Tandberg StorageLibrary T48-- Back of rack M5 x 12 (black) screws (total qty installed = 16) (total qty shipped = 18) Insert M3 x 8 screws here (one on each side) Figure 7 Attaching the Tandberg StorageLibrary T48 to the rails at the back of the rack ADDITIONAL INFORMATION Library operation and use--reference the individual Product Manuals at www.tandberg.com Technical support--go to www.tandberg.com For a more complete list of weight warnings (multiple languages), see the Library Safety Notices at www.tandberg.com 7 OF 8 NOTES 8 OF 8