User manual TASCAM CD-01U

» CD PLAYER OWNER'S MANUAL D00864010A CD-01 U /CD-01UPro Important Safety Precautions O CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. For U.S.A. TO THE USER This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION Changes or modifications to this equipment not expressly approved by TEAC CORPORATION for compliance could void the user's authority to operate this equipment. For the customers in Europe WARNING This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Pour les utilisateurs en Europe AVERTISSEMENT Il s'agit d'un produit de Classe A. Dans un environnement domestique, cet appareil peut provoquer des interférences radio, dans ce cas l'utilisateur peut être amené à prendre des mesures appropriées. Für Kunden in Europa Warnung Dies ist eine Einrichtung, welche die Funk-Entstörung nach Klasse A besitzt. Diese Einrichtung kann im Wohnbereich Funkstörungen versursachen; in diesem Fall kann vom Betrieber verlang werden, angemessene Maßnahmen durchzuführen und dafür aufzukommen. CE Marking Information a) Applicable electromagnetic environment: E4 b) Peak inrush current: 5.2 A 2 TASCAM CD-01U/CD-01UPro Important Safety Instructions O 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 Only use attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tipover. · Do not install this apparatus in a confined space such as a book case or similar unit. · The apparatus draws nominal non-operating power from the AC outlet with its POWER switch in the off position. · The apparatus should be located close enough to the AC outlet so that you can easily grasp the power cord plug at any time. · An apparatus with Class I construction shall be connected to an AC outlet with a protective grounding connection. · Do not expose this apparatus to drips or splashes. · Do not place any objects filled with liquids, such as vases, on the apparatus. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. TASCAM CD-01U/CD-01UPro 3 Safety S Oafety Information This product has been designed and manufactured according to FDA regulations "title 21, CFR, chapter 1, subchapter J, based on the Radiation Control for Health and Safety Act of 1968", and is classified as a class 1 laser product. There is no hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the protective housings. The label required in this regulation is shown 1. CAUTION · DO NOT REMOVE THE PROTECTIVE HOUSING USING A SCREWDRIVER. · USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. · IF THIS PRODUCT DEVELOPS TROUBLE, CONTACT YOUR NEAREST QUALIFIED SERVICE PERSONNEL, AND DO NOT USE THE PRODUCT IN ITS DAMAGED STATE. Optical pickup: Type: KSM-900AAA Manufacturer: SONY Corporation Laser output: Less than 0.5 mW on the objective lens Wavelength: 775 to 815 nm 4 TASCAM CD-01U/CD-01UPro Table of contents 1 - Introduction Supplied accessories ..................................6 Environmental considerations .....................6 Some notes and precautions ..........................6 Beware of condensation .....................6 Back up memory .................................6 Rack - mounting the unit .......................7 Handling of compact discs ...........................7 7 - Advanced operations Auto Cue ......................................................18 Auto Ready .................................................18 Resume .........................................................18 Call ....................................................................18 Incremental play ..................................................19 Repeat playback .........................................19 A to B repeat playback ...............................19 Intro check .......................................................20 Output in monaural ..............................................20 Power on play ................................................20 Pitch control ..................................................20 Changing the playback speed without changing the key (Key original) ...................21 Program playback .......................................21 Editing a programmed track ......................21 Adding a track to the program .................21 Deleting a programmed track ....................22 Fade in and fade out .......................................22 Relay play ................................................22 Time display switching ..............................23 End of disc/track warning ......................................23 Eject block .............................................23 Fader start/Event start ..............................23 Fader start/stop .....................................23 Event start ...........................................24 Restoring factory default settings ...................24 External parallel control ........................................24 2 - Remote control unit Some notes and precautions .......................8 Batteries ........................................................8 Inserting batteries .....................................8 3 - Connections Audio equipment .......................................9 Connecting analog audio equipment ...........9 Connecting digital audio equipment ..........9 Power source ................................................9 4 - Features and their functions Front panel ..................................................10 Display .......................................................11 Rear Panel ...................................................12 Remote Control Unit ..................................12 5 - Menu operation Menu configuration ...................................14 Menu operation .........................................14 Operation basics .........................................14 8 - Specifications Specifications ........................................................25 Dimensional drawing ................................26 Error Messages ...........................................26 6 - Playback Discs for playback .......................................15 About finalization .......................................15 For MP3 CDs ............................................15 Playback modes ..........................................16 Basic playback operation ...........................16 Using headphones .......................................16 Track selection ............................................16 Selecting by track number .......................17 Search ..........................................................17 Frame search ...................................17 TASCAM CD-01U/CD-01UPro 5 1 - Introduction OE Environmental considerations Thank you for your purchase of the TASCAM CD01U/CD-01U Pro CD player. Before connecting and using the unit, please take time to read this manual thoroughly to ensure you understand how to properly set up and connect the CD-01U/CD-01U Pro, as well as the operation of its many useful and convenient functions. After you have finished reading this manual, please keep it in a safe place for future reference. Supplied accessories In addition to this manual, the CD-01U/CD-01U Pro have been packed with the following: RC-01UC remote control unit 2 AAA batteries Power cord Rack-mounting kit Warranty document Should any of these items be missing, or if you encounter any damage, please contact your TASCAM supplier. This unit was packed in its carton with special materials in order to prevent any damage during shipment. Please save the carton and packing materials in the event you need to transport the unit in the future. Environmental considerations The CD-01U/CD-01U Pro may be used in most places, but to maintain top performance and prolong operating life, do not place it in the following locations. On an unsteady surface, or where there is frequent vibration or resonance Near a window or where it can be exposed to direct sunlight Near heating or air conditioning vents, or in very hot or cold places Places with high humidity or poor ventilation Next to tuners, televisions or video decks, as this could cause noise or affect video images Some notes and precautions Connect the CD-01U/CD-01U Pro only to the specified power source. When unplugging the cord, grasp the plug itself. Clean only with a dry cloth. Do not use benzene, paint thinner or other agents that could damage the surface. Dust or grime on the top cover can be removed with a soft cloth lightly moistened with a diluted mild detergent solution. Beware of condensation If the unit is moved from a cold to a warm place, or used after a sudden temperature change, condensation inside the unit may occur, resulting in moisture on the internal mechanism or an inserted disc, thus impairing proper operation. Should this occur, leave the player turned on for one or two hours so that the condensation can evaporate before you begin operation. Also, please remove all discs from the unit if it will be moved, or not operated for an extended period of time. Backup Memory Even when the power is turned off, the following settings are retained. Playback mode Time display mode Auto ready ON/OFF Auto cue ON/OFF Pitch control value All menu settings 6 TASCAM CD-01U/CD-01UPro 1 - Introduction OE Environmental considerations Rack-mounting the unit Use the rack-mounting kit to mount the unit in a standard 19-inch equipment rack, as shown below. Remove the feet of the unit before mounting. If you are mounting the unit in a rack, leave 1U of space above it and 10cm (4 in) or more of space at the rear. The CD-01U/CD-01U Pro can be mounted in any angle between 0 to 90 degrees. SeeEnvironmental considerationson the previous page. Handling of compact discs The CD-01U/CD-01U Pro have been designed for the playback of CD-DA format discs and MP3 files recorded in ISO9660 format. In addition to ordinary 5-inch and 3-inch CDs, it can also play properly recorded CD-R and CD-RW discs. When removing a CD from its case, press down on the center of the disc holder to free the CD, then lift the disc out, holding it carefully by the edges. Removing a disc Keep discs away from direct sunlight, and places of high heat and humidity. If left in such places, warping could result. Do not affix any labels or stickers to the label side of the disc. Do not write on the disc with a ballpoint pen. Please do not insert discs that have adhesive remaining from tape or stickers that have been removed. If they are inserted into the player, they could stick to the internal mechanism, requiring removal by a technician. Hold the CD like this Only use circular compact discs. Avoid using non-cir cular promotional, etc. discs. The CD-01U/CD-01U Pro cannot play unfinalized CD-R/RW discs. Avoid getting fingerprints on the signal side (opposite the label side). When cleaning, wipe gently with a soft cloth from the center towards the outside edge. Dust and grime may cause skipping, so keep discs clean and store them in their cases when not being played. Do not use a C-thru disc. The unit does not support a C-thru disc. Therefore, you may not be able to insert a C-thru disc or may not be able to remove a C-thru disc that has been successfully inserted to the unit. In the latter case, try to press the DISPLAY and EJECT keys simultaneously, which may solve the problem. Do not use the DualDisc. DualDisc is two-sided playback only discs. Insertion or ejection of a DualDisc into/from CD-01U/CD-01U Pro is likely to cause scratches to the surface of the DualDisc. Scratched discs may not play in CD products. A DualDisc may not play in CD-01U/CD-01U Pro and a DualDisc could get stuck in and may not be able to be removed from the CD-01U/CD-01U Pro. Do not use any record spray, anti-static solutions, benzene, paint thinner or other chemical agents to clean CDs as they could damage the delicate playing surface. Discs should be returned to their cases after use to avoid serious scratches that could cause the laser pickup to skip. TASCAM CD-01U/CD-01UPro 7 2 - Remote control unit Some notes and precautions When the remote control will not be used for an extended period of time, please remove the batteries to prevent the possibility of battery acid leakage which could damage the unit. Should leakage occur, remove and discard the batteries, and wipe the battery case thoroughly with a cloth. Avoid getting the battery liquid on the skin. After cleaning, replace with new batteries. The remote control functions by using an infrared light signal. When using the unit to control the CD01U/CD-01U Pro, other devices that are turned on could be operated by its signal. If the range of remote operation becomes smaller, or commands do not always function properly, the batteries have become weak and should be replaced. Always replace both batteries with new batteries of the same type. Point the remote control to the remote sensor on the main unit. Do not obstruct the path between the remote control and the remote sensor. Batteries If batteries are used improperly, or if leakage or breakage occurs, the unit will not function. Please observe the cautions indicated on the batteries and their packaging to ensure proper usage. Confirm + and - polarity and follow the indications when inserting new batteries into the remote control. Do not use old and new batteries together. Even if the battery is the same size, the voltage may differ. Do not use batteries of different specifications together. Do not attempt to recharge batteries that are nonrechargeable. Do not open or disassemble batteries, throw them into a fire or put them in water. Inserting batteries 1. Open the lid. 2. Confirm +/- polarity, and insert two AAA batteries. 3. Close the lid. 7m 8 TASCAM CD-01U/CD-01UPro 3 - Connections Before connecting the CD-01U/CD-01U Pro to other units, please read their operation manuals thoroughly to ensure proper connection. Turn the power on only after all connections have been made. Audio equipment Connecting analog audio equipment Connect analog stereo amplifiers, mixers and recorders to the analog line outputs. Connecting digital audio equipment Digital stereo amplifiers, mixers and recorders can be connected through the optical digital output terminal. Connection cables are not supplied with this unit. Do not bundle the pin connection cords with the power cord as noise or diminished sound quality could result. Power source This unit has been designed to operate on the specified power voltage only. Do not plug the power cord into outlets of any other voltage. TASCAM CD-01U/CD-01UPro 9 4 - Features and their functions Front panel 1 POWER switch 2 Disc slot Insert CD into the slot, label side upwards. 3 Remote signal sensor 4 EJECT key Ejects a disc. This key cannot be used when Eject Block is on and disc is being played back. 5 Display The display is used to show the current status of the unit, as well as the current menu settings. 6 PITCH (MENU) control knob Push this control to turn the pitch control function on or off. When it is on, pitch value is shown on the Display, and pitch can be controlled +/- 12.5%. Even when the power is turned off, the pitch control ON/OFF setting is retained. When in shift mode, functions as the menu dial when rotated, and as the ENTER key when pushed. When playback is paused and SHIFT indicator is lit, frame accurate search can be performed using with this knob. 7 SKIP (INDEX/DIR SEARCH) keys Use these to perform track searches. When SHIFT indicator is lit, searches the index (Audio CD discs) or directory (MP3 discs). 8 SEARCH (A.CUE, A.RDY) keys Performs review or cue playback (search). When in shift mode, selects the Auto Cue level or turns the Auto Ready mode on and off. 9 PHONES level control Adjusts the headphone output level. 0 DISPLY key Pressing this key changes the time mode on the display. Even when the power is turned off, the time mode is retained. When in menu mode, exits the menu mode. q SHIFT key and indicator Turns the shift mode on and off. When in shift mode, the indicator lights and other keys have shift functions which indicated under the keys. Pressing this key again exits shift mode. w ¥? (JOG) key and indicator Changes the playback mode between playback and pause. The indicator stays on solid in playback mode and flashes in pause mode. When playback is paused and SHIFT indicator is lit, frame accurate search can be performed using with the PITCH knob. e CALL (PLAY MODE) key Locates the playback to the last play start point. When SHIFT indicator is lit, selects the playback mode. r ª (INTRO CHECK) key Use this key to stop playback. When Incremental Play is activated, pressing this key pauses at the beginning of next track. When in shift mode, enters Intro Check mode. t PHONES jack Use a standard pair of stereo headphones, equipped with a 1/4-inch plug, with this jack. 10 TASCAM CD-01U/CD-01UPro 4 - Features and their functions Display 1TRACK indicator 2 Track number display Shows the track number. In the menu mode, shows the menu number. 3 MP3 indicator Lights when a MP3 CD-ROM disc is inserted. 4 INDEX/DIR indicator Shows the index number (CD-DA) or directory number (MP3). 5 T and REMAIN indicators When the time mode is set to remain time mode, these indicators light. Total remain mode: Both T and REMAIN indicators light. Track remain mode: REMAIN indicator lights. 6 Time display This section is used to show time values, menu information or messages. 8 REPEAT indicators Indicates the current repeat mode. 9 PITCH indicator and pitch value display When pitch control is activated, shows the pitch value and PITCH indicator lights. In the menu mode, shows the menu parameters. 0 A.CUE indicator Lights when Auto Cue function is turned on. q A.RDY indicator Lights when Auto Ready function is activated. w RELAY indicator Lights when Relay Play mode is activated. e FADE indicator Lights when Fade in/out is turned on. r MONO indicator Lights when in Mono output mode. t RESUME indicator Lights when Resume mode is on. y INCR indicator Lights when Incremental Play is activated. 7 Play mode indicators Indicates the current playback mode. RANDOM: Random playback mode S: Single playback mode PGM: Programmed playback mode u KEY ORIGINAL indicator Lights when Key Original function is turned on. TASCAM CD-01U/CD-01UPro 11 4 - Features and their functions Rear panel 1 ANALOG OUTPUT terminals The analog line output terminals are for RCA pin jacks. The maximum output level is +6 dBV. 2 DIGITAL (OPTICAL) OUTPUT terminal Provides the digital audio signal in S/PDIF format. This connector outputs the 44.1KHz digital signals constantly even if pitch control is activated. 3 CONTROL I/O (RS-232C) connector This RS-232C interface allows control by a computer or by other serial controllers. Consult your TASCAM dealer the TASCAM web site for details of this port if you wish to use it. 4 RELAY IN/OUT jacks These jacks are used to perform the relay play operation between two or more CD-01U/CD-01U Pro, or perform the fader start or event start operation. 5 ANALOG OUTPUT (BALANCED) terminals (CD01U Pro only) The analog line output terminals are for XLR connectors. The maximum output level is +20 dBu. 6DIGITAL (AES/EBU) OUTPUT terminal (CD-01U Pro only) Provides the digital audio signal in AES/EBU format. This connector outputs the 44.1KHz digital signals constantly even if both control is activated. 7CONTROL I/O (PARALLEL) connector (CD-01U Pro only) Parallel control from an external devices can be performed. 8 IN Connect the power cable supplied with the CD01U/CD-01U Pro. Remote Control Unit 1 EJECT BLOCK key This turns the Eject Block mode on and off. 2 DISPLAY key Pressing this key changes the time mode on the display. 3 PLAY MODE key This selects the playback mode. During selection, the playback mode is indicated on the display in the following manner. Normal playback (in disc order): no indication Single playback: S lights up Program playback: PGM lights up Random playback: RANDOM lights up 4 EJECT key Press this to eject the disc. This key cannot be used when Eject Block mode is on and the disc is being played back. 12 TASCAM CD-01U/CD-01UPro 4 - Features and their functions 5 PITCH key +/- keys Use these keys to perform the pitch control function. 6 KEY ORIG key This turns the Key Original function on and off. 7 A.CUE/DEL key Sets the Auto Cue level. During program input, the selected program number track is deleted. 8 A.RDY/INS key Turns the Auto Ready function on and off. During program input, inserts a track into the program list. 9 REPEAT key Turns the Repeat Play mode on and off. Pressing and holding this key for one second or more enters the Repeat A-B mode. 0 INTRO CHECK key Enters the Intro Check mode. q MENU key Enters the Menu mode. w ENTER key Confirms the menu options and confirms the settings and editing on the menu. e PREV key Selects the previous menu option or setting on the menu. r NEXT key Selects the next menu option or setting on the menu. t Number keys These are used to select track numbers. y CLEAR key During track number input, the track number is cleared when this key is pressed. u PGM key Pressing this key enters the Program mode. i SKIP keys Use these keys to skip to the previous track or the next track. o SEARCH keys During playback or playback standby, press the key continuously for review or cue playback (search). p INDEX/DIR SEARCH key Use this key to select the index (Audio CDs) or directory (MP3 discs). a JOG +/- keys Pressing the key in pause mode performs the frame accurate search. s¥PLAY key Press this key to start CD playback. When incremental play function is activated, pressing this key play start from the next track. d READY key When this key is pressed during playback or while stopped, enters standby mode. f CALL key Locates the playback to the last play start point. gª STOP key Use this key to stop playback. When incremental play function is activated, pressing this key pauses at the beginning of the next track. TASCAM CD-01U/CD-01UPro 13 5 - Menu operation The various settings and editing operations possible with the CD-01U/CD-01U Pro are performed through menu options shown on the display. Among the many No. Menu Function Parameter Underlined values are factory default settings menu setting options, some may be made directly using the keys on the remote control. Manual reference Page 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 KEY-0 BLOCK REPEAT PROG FADE RELAY TIMER MONO RESUME EOM INCR PITCH RS232C F-PRE U-DATA Key Original Eject Block Repeat Playback A-B Repeat Playback Program Fade In/Out Relay Playback Fader/Event Start Power on Play Mono Output Resume EOM Time 25, 30, 35 sec. Incremental Play Pitch Step Baud rate setting Factory Preset User Data ON, OFF ON, OFF OFF, ON, A-B rogram operation OFF, 0.5-10.0 OFF, ON, FDR ON, OFF ON, OFF ON, OFF OFF, 5, 10, 15, 20, ON, OFF 0.1, 0.5, 1.0 % 96, 192, 384 (SURE) ON, OFF Key Original Eject Block Repeat Playback Program Playback Fade In/Out Relay Play 23 Power on play Output in Mono Resume EOM Incremental Play Pitch Control Restoring the default setting ÆÆ 21 23 19 19 21 22 21 20 20 18 23 19 20 24 ÆÆ When digital output signal from the AES/EBU terminal is not received correctly on the other digital equipment , set the user data to OFF then try again. Operation basics 1 Press the PITCH knob on the front panel when SHIFT indicator is lit or press the MENU key on the remote control. Menu No. Menu Parameter 4 Use the PITCH knob on the front panel or PREV/NEXT keys on the remote control to select the setting value. 5 Press the PITCH knob on the front panel or ENTER key on the remote control. Pressing the DISPLAY key on either the front panel or the remote control exits the menu mode. 2 Use the PITCH knob on the front panel, or PREV/NEXT keys or number keys on the remote control to select the menu item. 3 Press the PITCH knob on the front panel or ENTER key on the remote control. 14 TASCAM CD-01U/CD-01U Pro 6 - Playback Discs for playback The CD-01U/ CD-01U Pro can playback the types of discs listed below. Ordinary audio CDs available commercially (recorded in CD-DA format). CD-R and CD-RW discs recorded in CD-DA format, and properly finalized. MP3 files recorded in ISO9660 format on CD-R and CD-RW discs, and properly finalized. CD-R/RW discs that have not been finalized cannot be played back. Make sure the disc has been properly finalized before loading into the player. About finalization Even if audio data is recorded onto a CD-R/RW disc, if the TOC (table of contents corresponding to the recorded data) is not written on the disc after recording, the disc cannot be played back on conventional CD players. Finalization is the process of writing the TOC on the disc. A number of record companies have released titles on copy control CD discs as a means of protecting artist copyrights. Some of these discs do not comply with standard CD format specifications, and may not be able to be played on this unit. The CD-01U/CD-01U Pro can play back MP3 files recorded in formats which conform to ISO9660 level 1, level 2 and Joliet. For MP3 CDs CDs containing MP3 files can be played by the CD01U/CD-01U Pro with the following limitations on the number of files and directories. Maximum number of directories: 254 Maximum number of MP3 files: 255 File format: MPEG 1 audio layer 3 Bit rate: 32kbps to 320kbps Sampling frequency: 44.1KHz, Stereo File extension: mp3, Mp3, mP3, MP3 MP3 files are played as the order in the following diagram. In this manner, playback is performed from the top level directories. The CD-01U/CD-01U Pro can only read the files in the first session of a multi-session disc. ID3 tag display for MP3 playback is not supported. : Folder (Directory) : MP3 File TASCAM CD-01U/CD-01UPro 15 6 - Playback Playback modes There are four different playback modes. The mode selected is indicated on the display. Normal (continuous) playback mode: no indication lamp Single playback mode: S is lit Program playback mode: PGM is lit Random playback mode: RANDOM is lit The playback mode can be selected using the PLAY MODE key on the remote control. Pressing the key changes the playback mode in the following order: Cont Single Program Random You can also select the playback mode pressing the CALL/PLAY MODE key on the front panel when in SHIFT mode. While the mode can be changed from any playback mode, the explanation in this manual will assume the user is starting from the normal Continuous mode. Basic playback operation 1 Push the POWER switch to turn on the unit. The display will indicate NO DISC. 2 Insert a disc into the slot, label side upwards. After a disc is inserted, the total playing time and number of tracks will be displayed. Do not force the disc into the slot, the CD-01U/CD01U Pro will pull the disc when partially inserted. 3 Press the ¥? key on the front panel or ¥ key on the remote control unit. The play indication will light up, and playback begins from track 1. The number of the current track in play is indicated on the display. To stop playback, press the ª key on the front panel or remote control unit. To pause playback, press the ¥? key on the front panel again or key on the remote control unit. The indication will blink, and the unit will enter playback standby mode. To resume playback, press the ¥? key or the front panel or ¥key on the remote control. To remove the disc Press the EJECT key on either the front panel or remote control unit. You can insert back a disc into the slot by pressing the EJECT key or pull the disc and slot it in again. When Eject Block is activated, EJECT key cannot be used when disc is being played back. To play a desired track Press the SKIP key to select the desired track or numerical keys. Using headphones Plug the headphone cord into the PHONES jack. Adjust the volume with the volume control. ume too high. Listening at high volumes for extended periods of time may result in permanent hearing damage. When using headphones, take care not to turn the vol- Track selection Select desired tracks for playback with the skip keys on the front panel or on the remote control. To restart playback from the beginning of the track in play, press the µ once. To skip to the previous track, press µ twice. To skip to the next track, press once. When Auto Cue is off and the CD-01U/CD-01U Pro is in stop or play mode, playback begins after selecting the track. When Auto Cue is off and the CD-01U/CD-01U Pro is in pause mode, the beginning of selected track is located ,and the unit enters playback standby mode. When Auto Cue is on and the CD-01U/CD-01U Pro is in play mode, playback begins after selecting the track. When Auto Cue is on and the CD-01U/CD-01U Pro is in pause or stop mode, when a track is selected, the point where sound begins (not where the track begins) on that track is located, and the unit enters playback standby mode. 16 TASCAM CD-01U/CD-01UPro 6 - Playback Selecting by track number Using the number keys on the remote control, the number of the desired track can be entered directly. Even numbers with two (Audio CD) or three (MP3) digits can be entered easily. For example: Track 9 (Audio CD): press 0 then press 9. Track 9 (MP3): press 0, 0, and 9. Frame search During playback standby, using the PITCH knob in shift mode performs the frame accurate search. Also, during playback standby, pressing the JOG +/keys on the remote control performs the frame search. This function does not operate with MP3 discs. Search During playback or playback standby, pressing the SEARCH keys continuously enables the search of a desired portion within a track for playback. The search function does not operate with MP3 discs. TASCAM CD-01U/CD-01UPro 17 7 - Advanced operations Auto Cue When the Auto Cue function is turned on and a track is selected, the point where sound begins (not where the track begins) on that track is located to and the unit enters pause mode. When the ¥ key is pressed, playback begins at exactly that point. Turning the Auto Cue function on and off Press the µ key on the front panel when SHIFT indicator is lit or A.CUE/DEL key on the remote control to select the auto cue level. Auto cue level: OFF (default), -24, -30, -36, -42, -48, -54, -60, -66, -72 (dB) When the Auto Cue function is activated, A.CUE indicator is lit on the display. Even when the power is turned off, the Auto Cue setting is maintained. Auto Cue is not supported for MP3 playback. During stop mode, to cue to the start of sound on track one, just press the key. Auto Ready When the Auto Ready function is on, after each track is played, playback standby mode is entered at the beginning of the next track. The behavior of Auto Ready function is follows. Continuous play mode: Pause the beginning of the next track when playback of the current track is finished. Single play mode: Pause the beginning of the current track when playback of the current track is finished. Program play mode: Pause the beginning of the next programmed track when playback of the current track is finished. When the Auto Cue function is also on, playback standby mode is entered at the beginning of the sound on the selected track, and not the beginning of that track. Turning the Auto Ready function on and off Press the key on the front panel when SHIFT indicator is lit or A.RDY/INS key on the remote control to turn the function on and off. When the Auto Ready function is on, A.RDY indicator is lit on the display. Even when the power is turned off, the Auto Ready setting is maintained. Resume When the resume function is on, the playback stop position is memorized and playback starts from that position when playback is resumed. In the case of MP3 discs, the playback starts from the beginning of the last playing track when playback is resumed. Turning the Resume function on and off Set the resume function on and off on the menu (menu number 09 RESUME). When the Resume function is on, RESUME indicator is lit on the display. Even when the power is turned off, this setting is maintained. Call Pressing the CALL key on either the front panel or remote control locates the unit to last play start point, and the unit enters playback standby mode. This function is not supported for MP3 playback. 18 TASCAM CD-01U/CD-01UPro 7 - Advanced operations Incremental play This function allows auto-cueing of the playback point to the start of the next track when the ª key on either the front panel or remote control is pressed, or a stop command is received from the external device. Turning the Incremental play function on and off Set the incremental play function on and off on the menu (menu number 11 INCR). Pressing the ª key again or receiving the stop command again, unit enters stop mode. When this mode is enabled, pressing the ¥ key on the remote control or receiving the play command from the external device starts playback from the beginning of the track following the current track. When the this function is on, INCR indicator is lit on the display. Even when the power is turned off, this setting is maintained. Repeat playback Press the REPEAT key on the remote control to turn on the repeat mode. In this mode, all the tracks on the disc are played continuously. During playback, if the repeat mode is turned on, playback continues as before, and when the last track finishes, playback resumes from the first track. If repeat mode is turned on when the deck is stopped, press the PLAY key to begin operation. Combining the repeat mode with the Program, Singletrack playback and Random playback functions will enable Program Repeat, Single-track Repeat and Random Repeat operations, respectively. Turning the Repeat play function on and off Turn the repeat play function on and off on the menu (menu number 03 REPEAT). Or press the REPEAT key on the remote control. When the this function is on, REPEAT indicator is lit on the display. Even when the power is turned off, this setting is maintained. A to B repeat playback If a specific portion between two points on the disc is specified, that portion can be played back repeatedly. 1 During playback and the repeat function is off, press and hold the REPEAT key on the remote control more than 1 second. Or set the repeat mode to A-B on the menu (menu number 03 REPEAT). REPEAT indicator flashes on the display. 2 Press the REPEAT key on the remote control or PITCH knob on the front panel at the beginning of the desired portion on the disc. A-B indicator flashes on the display. 3 At the end of the desired portion on the disc, press the REPEAT key on the remote control or PITCH knob on the front panel again. REPEAT and A-B indicators are lit up on the display, and the desired A-B section will be played repeatedly. To cancel Repeat A-B mode and resume normal playback Press the REPEAT key on the remote control once more. There are three additional ways to cancel repeat A-B mode: Press ª key. Search the other track. Eject the CD. Both repeat start (A) and end (B) points can set to within a track. This function is not supported for MP3 playback. TASCAM CD-01U/CD-01UPro 19 7 - Advanced operations Intro Check The Intro Check function allows only the beginning of each track to be played for 10 seconds. This function is operational both at stop and during normal playback. 1 Press the STOP/INTRO CHECK key on the front panel when SHIFT indicator is lit and playback stops. Or, pressing the INTRO CHECK key on the remote control to turn the intro check function on and off. Int is shown on the display. 2 Press the ¥? key on the front panel or ¥key on the remote control. This function works in normal (continuous) play mode and program play mode. To exit the intro check mode, press ª key on either the front panel or remote control, or INTRO CHECK key on the remote control. The intro check mode is also canceled when play mode is changed. Output in monaural Both analog and digital output can be set to mono output mode. Set the mono output mode on and off on the menu (menu number 08 MONO). When the this function is on, MONO indicator is lit on the display. Even when the power is turned off, this setting is maintained. Power on play By using an external timer, you can set the CD01U/CD-01U Pro to play the loaded disc automatically when the unit is turned on by the timer. 1 First, plug the power cord of the CD-01U/CD-01U Pro into the power outlet of the timer. 2 Load a CD into the unit. 3 Set the TIMER menu (menu number 07 TIMER) to on. 4 Set the timer to the desired time. Consult the timer's operation manual for details. At the set time, the power to the CD-01U/CD-01U Pro will be turned on, and playback will automatically begin. Pitch control When playing back an audio CD or MP3, the pitch (or speed) of the playback can be varied. Pitch can be varied +/- 12.5%. value is shown on the display and PITCH indicator lights. 2 Rotate the PITCH knob or use the PITCH +/- keys to set the pitch. Use the PITCH menu (menu number 12 PITCH) to adjust the pitch control steps from 0.1, 0.5, or 1.0% (Default: 0.1%). 1 Press the PITCH knob on the front panel when SHIFT indicator is unlit or press the PITCH key on the remote control to turn the Pitch Control function on and off. When the pitch control function is activated, pitch Digital output provides the 44.1KHz digital signals constantly even if pitch control is activated. 20 TASCAM CD-01U/CD-01UPro