User manual TEXECOM PREMIER 24

Veritas User Guide Quick Reference Guide THANK YOU FOR VOTING TEXECOM THANK YOU FOR VOTING TEXECOM USER GUIDE Security Control Panels Issue 2 1 INS167 Overview Premier Series User Guide 1. Overview Introduction Users of the alarm system will be assigned a unique 4, 5 or 6 digit User code. User codes are used to arm and disarm the system. Some User codes can also access additional options such as, system tests and omitting zones. Keypads will be installed throughout the premises, usually one at each entry/exit door. The keypads are used to perform all of the system operations i.e. Arming, Disarming etc. Most User codes can be used at any keypad on the system. However, Local Users will only be able to use certain keypads on the system. The Emergency Keys In case of emergency, the alarm system can provide three immediate emergency alarms by pressing and holding two specific keys for two seconds. !" The emergency keys can be enabled/disabled for each keypad on the system. The Panic alarm can be programmed for either audible or silent operation. The Panic alarm can be programmed for either instant or delayed operation. Emergency Alarm Panic Alarm (PA) Fire Medical Press Keys !&" #&$ %&& The Quick Arm Keys The `Quick Arm' keys allow the system to be armed without having to enter a User code first. !" The `Quick Arm' keys will only work if the keypad has been programmed to allow arming in this way. To FULL arm the system, press '. To PART arm the system, press !, ( or " followed by ). Keypad Lock The keys on the keypad can be locked to prevent unwanted access to the system. To Lock the keys, press * and + together. To Unlock the keys, press * and + together again. 2 INS221 !" The Emergency keys will NOT operate with the keys locked. Premier Series User Guide Overview LED Indicators Five LED indicators have been provided to indicate the status of the system. LED Power Status On Flashing Meaning AC mains is present on the control panel AC Mains is not present, the control panel is running on the standby battery The system requires attention, contact your installer The system does NOT require attention All zones are secure and the system is ready to be armed One or more zones are active The system has zones (with the `Force Omit' attribute) that are active The system is armed (can also be programmed for other indications) The system is unarmed (can also be programmed for other indications) One or more zones are omitted No zones are omitted Service On Off Ready On Off Flashing Info. On Off Omit On Off Zone Faults During Arming Before attempting to arm the system, ensure that the premises are secure (all doors and windows closed etc.) and the Ready light is on. If an attempt is made to arm the system with any zones active (e.g. door ajar, open window, etc.) the internal sounders will bleep repeatedly (fault tone) and the display will show the zones that are active. The fault tone will stop and the exit tone will resume when all zones are secure. If it is necessary to leave a zone open then it must be omitted (see page 8 for details). !" !" INS221 If an active zone cannot be secured then it may be `in fault', in this case contact the alarm company immediately. Arm Fail - Failing to Arm If the exit procedure is started and zones are still `Active' at the end of the exit procedure, an Internal alarm will occur (internal sounders only) and the strobe light on the external sounder will flash. If this occurs the arm fail must be cleared and the zone in fault identified before the system can be armed (see page 6 for details on clearing an Arm Fail). The Ready LED To help prevent faults during arming a Ready light has been provided, see table above for details on how the Ready LED operates. 3 Operating the Alarm System Premier Series User Guide 2. Operating the Alarm System To FULL Arm the System The system is FULL Armed when ALL zones are ON (not omitted). !" ' Your Installer may have programmed the system so that it can be set by just pressing , if this is the case then there is no need to enter the User code below. 1. Ensure that the premises are secure (all doors and windows closed etc.) and the Ready light is on 2. Enter a valid User code ,,,, 3. Press * to arm The exit tone will sound 4. Leave the premises When the system has armed the exit tone will stop To PART Arm the System The system is PART Armed, when ONE OR MORE zones have been left OFF (omitted) i.e. the landing or a bedroom. !" The system is only Part Armed when zones are omitted using the `Part Arm' procedure (omitting zones manually (see page 8 for details) is not classed as Part Arming). The bottom line of the display is programmable for each Part Arm. Your Installer may have programmed the system so that it can be Part Armed by just pressing !, ( or " followed by ), if this is the case then there is no need to enter the User code below. 1. Ensure that the premises are secure (all windows and doors not being omitted are closed) and the Ready light is on 2. Enter a valid User code ,,,, 3. Press ) 4. Use keys ! - " to select the required Part Arm 5. Press * to arm normally or press - to arm silently The exit tone will sound (if silent arm has not been selected) 6. Leave the protected area When the system has armed, the exit tone (if sounding) will stop 4 INS221 Premier Series User Guide Operating the Alarm System To ARM Individual Areas If the system has been split up into separate areas of protection i.e. Area 1 = House, Area 2 = Garage, Area 3 = Shed etc. These areas can be individually selected for FULL or PART arming as required. !" Areas are selected by using keys ! - . (the select an area followed by ' or +). / key can also be used to Only areas that exist on the system can be selected. (A `Star' means the area can be selected and a `Dot' means the area cannot be selected). Pressing 0 will select/deselect all areas, pressing ' will toggle between the first 8 areas and the second 8 areas (where applicable). 1. Ensure that the premises are secure (all windows and doors not being omitted are closed) and the Ready light is on 2. Enter a valid User code ,,,, 3. Press ' 4. Use keys ! - . to select the required areas 5. Press * or - to FULL arm the areas Or 5. Press )!, ( or " followed by * or - to PART arm the areas The exit tone will sound (if silent arm has not been selected) 6. Leave the premises When the system has armed, the exit tone (if sounding) will stop To DISARM the System The entry time is divided into two sections, the Entry time and the 2nd Entry time. If the Entry time expires, an Internal alarm will occur and the 2nd Entry time will start. If the 2nd Entry time expires, an Intruder alarm will occur (all internal and external sounders). !" It is perfectly normal for the 2nd Entry time to be programmed as zero, in which case, an Intruder alarm will occur as soon as the Entry time expires. 1. Enter the premises via the designated entry point The entry tone will start 2. Enter a valid User code ,,,, The entry tone will stop INS221 5 Operating the Alarm System Premier Series User Guide To DISARM the System When Not in Entry 1. Enter a valid User code ,,,, 2. Press * To CANCEL the Exit Mode Once the exit mode has been started you should leave the premises immediately, however, if for some reason you decide not to leave, the exit mode must be cancelled. 1. Enter a valid User code ,,,, 2. Press * The exit tone will stop. To CLEAR an Arm Fail When the system tries to arm with zones active (open), the internal sounders will sound and the external strobe will be flashing to indicate a problem. For details on preventing an Arm Fail condition, please refer to page 3. !" If you were not present when the Arm Fail occurred or you do not clear the Arm Fail, the internal sounders will continue to sound and the external strobe will continue to flash. 1. Enter a valid User code ,,,, The internal and external sounders will stop, the external strobe will continue to flash and the number of the zone that caused the Arm Fail will be displayed. 2. Enter a valid User code ,,,, and press 12 To SILENCE an Alarm When an alarm occurs on the system, the internal and external sounders will normally sound for a pre-programmed time (normally 15 minutes). !" If you were not present when the alarm activated, the internal and external sounders may have already stopped but the external strobe will still be flashing. When alarm information is being displayed, pressing the SCROLL key will slow down the display and also allow manual scrolling through the events. 1. Enter a valid User code ,,,, The internal and external sounders will stop and the number of the zone that caused the alarm will be displayed. The alarm now needs to be reset. 6 INS221 Premier Series User Guide Operating the Alarm System To RESET After an Alarm USER Reset Once the alarm has been silenced (see page 6 for details), the system will need to be reset. !" If the system has been programmed, to be reset by an Engineer, pressing 1 will not return the display to normal, if this is the case see ENGINEER Reset for details. The system may have been programmed to be reset by Anti-code, if this is the case, see ANTI-CODE Reset for details. 1. Enter a valid User code ,,,, 2. Press 1 The external strobe will stop, the system will chime and the display will return to normal. ENGINEER Reset If the system has been programmed to be reset by an Engineer following an alarm activation, you will still be able to silence the alarm by entering a valid User code (see page 6 for details). !" The system cannot be armed again until the alarm has been reset. 1. Contact the telephone number on the display (if programmed) or the telephone number on the last page of this User Guide ANTI-CODE Reset If the system has been programmed to be reset using an Anti-Code following an alarm activation, you will still be able to silence the alarm by entering a valid User code (see page 6 for details). 1. Enter a valid User code ,,,, 2. Press 1 The display will show a random code number i.e. 4281. 3. Contact the telephone number on the display (if programmed) or the telephone number on the last page of this User Guide and quote the random code number You will be given a 4-digit Anti-Code i.e. 5624. 4. Enter the Anti-code that has been given to you ,,,, 5. Press * If the Anti-code is correct, the keypad will bleep to indicate that the system has been reset and the display will return to normal. INS221 7 !" The system cannot be armed again until the alarm has been reset. Operating the Alarm System Premier Series User Guide To OMIT Zones It is possible to exclude (omit) individual zones when arming i.e. if a zone is `in fault'. Users with access to this function can only omit zones that have been programmed as `Omittable'. !" If the zone can be omitted, there will be a `Star' to the right of the zone number. Only zones that have the `Omit' attribute assigned to them can be omitted. A `Star' will appear to the left of the zone number to indicate that the zone has been selected for omitting. All omitted zones will be automatically reinstated the next time the system is disarmed, unless programmed otherwise. To re-instate zones manually, simply follow the instructions again. However, when the 3 key is pressed on this occasion, the zones will be re-instated. 1. Enter a valid User code ,,,, and press 3 2. Enter the zone number ,,, 3. Press 3 to omit the selected zone Repeat for other zones if required. 4. Press 4 when finished Continue to arm the system as normal. The Turn CHIME On and Off The system can be set up so that activating (opening) certain zones will cause the internal sounders to chime. This would normally be used on a front door, exit button etc. !" !" Zones will only cause the internal sounders to chime if they are selected for chime (see page Master User Guide for details on selecting which zones chime). Once a zone has been selected for chime, the Chime facility can be manually turned on and off as required. The system can also be programmed to automatically turn chime on and off under certain conditions i.e. certain times of the day, door left open etc. If no zones have been programmed for Chime, then turning Chime on and off will have no effect. To turn CHIME On 1. Press The Chime tone will sound. 8 To turn CHIME Off 1. Press The Error tone will sound. INS221 Premier Series User Guide Operating the Alarm System To CHANGE Your User Code Users with access to this option can change their own User codes. User codes are unique to each user and can be 4, 5 or 6 digits long. !" Only the User code that is entered to access the change code menu will be changed. Before changing your code, it is vital that you memorise or write down the new code you are about to program. Failure to remember your code will require an engineer visit to re-program a new code for you. This may incur a call-out charge. 1. Enter the User code that requires changing ,,,, 2. Press 4 3. Press * 4. Press ( 5. Press * 6. Enter a new 4, 5 or 6-digit User code ,,,, 7. Press * to accept the new code 8. Press 1 to exit the menu The display will return to normal. INS221 9 Quick Reference Guide Premier Series User Guide 4. Quick Reference Guide Operation To Full Arm the System To Part Arm the System Description Enter a valid User code Press Yes (or press Chime to arm silently) Enter a valid User code Press Part Select Required Part Arm Press Yes (or press Chime to arm silently) Enter a valid User code Press Area Select Required Area using keys 1 - 8 Press Yes (or press Chime to arm silently) Enter a valid User code Press Yes (if the entry mode was not started) Enter a valid User code Press Yes Enter a valid User code Press Reset Enter a valid User code Enter a valid User code Press Reset Contact Your Installation Company Enter a valid User code Press Reset Contact Your Alarm Receiving Centre Quote 4-digit code shown on display Enter 4-digit code given by Receiving Centre Press Yes Enter a valid User code Press Omit Enter Zone Number(s) Press Menu when finished Press Yes to Arm Press Chime Once to Turn ON Press Chime Again to Turn OFF Enter a valid User code Press Menu followed by Yes Press 2 followed by Yes Enter a new 4, 5 or 6 digit User code Press Yes to accept Press Reset to return to the normal display Action To Arm Individual Areas To Disarm the System To Cancel the Exit Mode To Clear an Arm Fail To Silence an Alarm To Reset After an Alarm To Engineer Reset To Anti-code Reset To Omit Zones Turn Chime On/Off To Change User Code ,,,, * or ,,,, ) !, ( or " * or ,,,, ' !-. * or ,,,, * ,,,, * ,,,, 1 ,,,, ,,,, 1 _____________ ,,,, 1 _____________ !"#$%&'((((' ,,,, * ,,,, 3 ,,,... 3 * ,,,, 4* (* ,,,, * 1 INS221 10 Premier Series User Guide Installation Details 5. Installation Details Areas No. Description Exit Time Sec. Sec. Sec. Sec. Entry Time 1 Sec. Sec. Sec. Sec. Entry Time 2 Sec. Sec. Sec. Sec. Bell Delay Min. Min. Min. Min. Bell Duration Min. Min. Min. Min. Abort Time Sec. Sec. Sec. Sec. Keypads No. Location Area Quick Arm Emergency Keys PA Fire Med User Codes User 01 Name Type Master Default 5678 N/A N/A N/A N/A N/A New Code Area Time Lock Zones No. Description Type Area Omit 1 Part Arms 2 3 INS221 11 Installation Company Details Installation Engineer: Installation Company: Address: Telephone Number: Installation Date: Service Record Date Serviced Comments Engineer Emergency Telephone Numbers For 24 Hour Call Out For Anti-Code Reset Control Panel Details Model Location Premier 24 Premier 48 Premier 88 Premier 168 Premier 640 © TEXECOM LTD. 2000 - 2005 INS221-2