User manual TVIX HD M-5000U

User Manual TViX HD M-5000U /M-5000A All specifications and information are subject to changes without further notices Safety Notice Keep your TViX away from heated areas, such as sunlit areas, heaters etc. Set it up in well ventilated places. Ensure that a free airflow is maintained around the appliance. Do not set the TViX up in places that are exposed to oil, water, dust, humidity or rain and wind. Keep all magnetic materials away from the TViX. Magnetic materials such as speakers or magnets may erase or cause damage to the data stored in the hard disk. Do not try to disassemble or remodel the device. Doing so may cause malfunction or fire. Do not touch the power plug with wet hands or use defective power cables & electric outlets. It may cause electric shocks or fire. Do not drop the device. Doing so may cause critical damage to the hard drive. The socket-outlet shall be installed near the equipment and shall be easily accessible. 2 Usage Precautions Please read the following usage precautions before using your TViX HD. Make sure the power is off when you connect the A/V cable between the TViX and the TV. When cleaning the TViX product, pull out the power cord and then wipe it with a soft piece of dry cloth. When connected to the computer through the USB cable the TViX HD acts as an external USB storage device (In this state, there is no video/audio output and the VFD will show as USB ON). For normal TViX play mode, disconnect the USB cable connected to the computer and turn on the TViX HD. When the TViX HD is playing and the USB is connected to the computer, a USB ON icon will be displayed on the center of the screen. Disconnecting the USB port will show the original screen. Make sure the jumper setting of the hard disk which is installed on the TViX HD is set as Single Master. Otherwise the hard disk will not be recognized by TViX HD. When detaching the HDD, please let the heat out sufficiently. The supplied cables and accessories are recommended for customized best performance of the TViX HD. Using other cables or accessories may not provide best performance. If you want to unplug the device, press the Stop button in 'Unplug or Eject Hardware'. Windows 98SE and Windows ME does not support NTFS file format. However, NTFS file format is available on Windows 2000/XP. "Primary Partition" is recommended when creating two or more partitions with a single hard disk drive. If you choose FAT32 file format on Windows 2000/XP, the drives maximum size will be limited to 32GBs. If you want to use a single drive letter of 32GBs or more, you have to format on Windows 98SE/ME. The certification sticker mark is on the bottom of the device. The Difference between M-5000A from M-5000U. - M-5000U will power up after the main power switch (at the back of the unit) is turned on. - M-5000A will power up only after you press power switch on the top of the unit or using remote tranceiver. Other functional features are exactly same and both use the same firmware. You can insert the character using remote-numeric key. Number 1 key is changed as @ when this key is pressed. : / _ - ** Some functions will require you to update the firmware in first. 3 Table of Contents Safety Notice .............................................................................................................................................. 2 Usage Precautions ..................................................................................................................................... 3 1 Introduction.................................................................................................5 1.1 1.2 1.3 1.4 Multimedia Player ....................................................................................................................... 5 Audio Player ............................................................................................................................... 6 External Storage ......................................................................................................................... 6 Specifications.............................................................................................................................. 7 2 Name of Each Part......................................................................................8 2.1 2.2 2.3 2.4 Unit Control................................................................................................................................. 8 Front VFD ................................................................................................................................... 8 Cable Connection ....................................................................................................................... 9 Package Contents ...................................................................................................................... 9 3 Installation and Connection.....................................................................10 3.1 3.2 3.3 3.4 3.5 Making an HDD Folder ............................................................................................................. 10 Video Connection ......................................................................................................................11 Audio Connection ..................................................................................................................... 13 LAN Connection........................................................................................................................ 14 HDD Installation/Exchange....................................................................................................... 22 4 TViX HD Setup Menu ................................................................................24 4.1 4.2 Audio/Video Setting .................................................................................................................. 24 MISC Setting............................................................................................................................. 26 5 Easy Usage of TViX HD ............................................................................28 5.1 5.2 5.3 Play Video Files ........................................................................................................................ 28 Play Audio Files ........................................................................................................................ 29 Play Image Files ....................................................................................................................... 30 6 Using the remote control .........................................................................31 6.1 6.2 6.3 Basic Functions ........................................................................................................................ 31 Descriptions of Each Buttons ................................................................................................... 32 Extra Features .......................................................................................................................... 39 7 8 Firmware Upgrade ....................................................................................43 Using USB Connection with the PC........................................................45 8.1 8.2 8.3 8.4 Windows 98SE Driver Installation ............................................................................................ 45 Making a Partition and Formatting the HDDs under Windows 98SE / ME............................... 49 Making a Partition and Formatting the HDDs under Windows 2000 / XP ................................ 51 Unplug or Eject Hardware ........................................................................................................ 54 9 Appendix - Technical Terms ....................................................................55 10 GNU General Public License ...................................................................57 4 1 Introduction 1.1 Multimedia Player TViX HD is a standalone, multimedia hard disk player which plays digital videos, digital music, digital still images and DVD files to a TV display and home entertainment system. You can enjoy digital contents in your living room without having to burn discs or having to play it back on a DVD or CD player anymore. TViX HD plays back DVD movies with the full functionality of DVD navigation. You can create your own virtual DVD library by storing your personal collection of DVDs in .ISO or .IFO format and watch them exactly as if they were running from the original DVDs (all original features included: Menu, Chapter, Audio Stream, Subtitle, Fast Forward, Rewind, Slow, Pause, Step Forward, Repeat, Search etc.). TViX HD plays back high definition video (up to 1920x1080i) and still images. Pre-recorded HDTV programs from a digital TV set-top box or personal digital video contents taken by a HDVTM camcorder can be played back with the TViX HD on a high definition display. The TViX HD features a DVI connector and component, which will match the high resolution of HD level video contents. Using the latest EM8621 processor, TViX HD supports the latest multimedia formats (WMV9 & WMV HD) as well as MPEG4 3.11,4.0 and 5.0. Using the high definition DVI output, you can directly connect the TViX HD to your HDTV. TViX HD supports DTS hardware decoder to mix DTS sound into 2 channels for a more dynamic sound quality. The TViX HD can be networked with a PC system using its built-in LAN port. You are able to navigate to a PC file through TViX HD's network and play the file from its original destination without having to copy it into the TViX first. The TViX HD can be networked with a PC system using its built-in LAN port. You are able to navigate to a PC file through TViX HD's network and play the file from its original destination without having to copy it into the TViX first. We're supporting the file copy via LAN. With two USB2.0 host ports, you can now attach additional external USB hard drives to further extend the storage capacity or transfer files from another USB device such as a thumb drive. You can also playback files from a digital camera, USB flash driver, USB flash card reader, or a MP3 player. ** For the further functions, please refer to following FAQ. http://www.tvix.co.kr/eng/faq 5 1.2 Audio Player TViX HD can play a variety of audio files such as FLAC, MP3, Ogg Vorbis or WMA (Windows Media Audio) through the TV speaker and any other audio systems. You can listen to your favorite music files nonstop, by organizing a custom winamp playlist. Now you can enjoy music all day without changing CDs. You can watch picture slideshows with the option of background music (supports music slideshows using picture images). 1.3 External Storage If you connect to a USB 1.1 port, the TViX HD will work at USB 1.1 speed, so we strongly recommend that you use USB 2.0. It can be used as an external device to save video, audio, image files, data, program backups, etc. USB 2.0 enables TViX HD to become an external storage device which supports up to 480Mbps. It supports Plug & Play, so Windows will automatically recognize TViX HD. If you connect the USB port when playing the TViX HD, the VFD will show as USB ON. When you disconnect the USB, you do not have to reboot the TViX HD for continuous use. If you are a Windows98SE user, you should download a USB storage driver from our website www.tvix.co.kr/Eng before you connect your TViX HD with your system. You do not need to install a driver in Windows ME/2000/XP. You can download NetShare installer from our website www.tvix.co.kr/Eng before you configure NFS network. If you select to NFS mode, you can play the TP or DVD jukebox without stutter. 6 1.4 Specifications Sigma Design EM8621 7 Alpha-Numeric Character 5 Digit Numeric Display Format :.wmv, .avi, .mpg, .vob, .mp4, .asf, .tp, .trp , .IFO, .ISO Main Chipset VFD Display Video Codec : MPEG 1 / 2 / 4, AVI, XVID Resolutions up to 1920 x 1080i MP3, WMA, AAC, Ogg, PCM, M4A, FLAC, WAV AC3, DTS Pass Through and Down Mixing JPG USB2.0 Host 2 Ports USB2.0 Target 1 Port Audio Photo Connectivity LAN (10/100Mbps) Multi I/O Jack (Optional Breakout Box) Video DVI, Component, S-Video, Composite, Audio Digital : Coaxial, Optical / Analog: Stereo AV In / Out File Formats Subtitle ODD Support Language FAN FAN Control Main Memory Flash ROM Shape Dimension Weight NTFS, FAT32 Text Subtitle : smi,sub,srt,aqt,utf,lrc / Image Subtitle : sub (with idx) Through USB 2.0 Host English, French, German, Spanish, Italian, Portuguese, Swedish, Norwegian, Danish, Japanese, Korean 40mm Brushless FAN Temperature Sensing, Variable Speed Main Memory 8 Mbyte Cylindrical 131mm (Diameter) 185mm (Height) 1,200g (without HDD) 1,800g (with HDD) Internal Power 90~240V Free Voltage 7 2 Name of Each Part 2.1 Unit Control Basic functions can be done without the remote control. POWER button Function button STOP button PLAY button SETUP button 2.2 Front VFD Information will be displayed on the VFD. Video out mode Play mode and information VFD shows current Folder/Filename while navigation. Due to display(VFD) restriction we only support English alphabets. 8 2.3 Cable Connection You can connect the TViX to a TV display or audio Amplifier using the A/V cable. USB Input Port Cooling Fan Optical Port S-Video Video Stereo Component Coaxial USB Host Multi I/O Port Power On/Off LAN Port Unit Power 2.4 Package Contents TViX HD M-5000U Remote Control A/V Cable Manual Power cable x 2 USB Cable 9 3 Installation and Connection 3.1 Making an HDD Folder 1. As shown in the picture below, one end of the USB cable should be connected to the USB connector of the TViX and the other end to the computer. CAUTION! The USB cable has a different shape on both ends. We use a USB 2.0 type "A" Plug(male) to "B" Plug(male). 2. After connecting to the PC, turn on the power of the TViX. 3. Double click the icon `My Computer' on your monitor and you will see a newly created drive; TViX (D:) as shown in picture `A'. (The name of the drive can be changed.) 4. For easy usage, double click TVIX (D:) and make separate folders named video, audio, and photo. Then store all your files accordingly to each folder. 10 3.2 Video Connection We support DVI, Component, S-Video, Composite video output for connecting to the TV and each output needed to change settings on the TViX HD. The highest quality components are as follows: DVI > S-Video > Composite. 3.2.1 Connection with an Ordinary (Composite) TV Output Connect the TViX HD and your TV using the yellow video cable. Turn on the TViX HD and TV. Select an appropriate video input mode on your TV until you get the initial TViX HD screen. 3.2.2 Connection to S-Video Output Connect the TViX HD and your TV using the S-Video cable. Turn on the TViX HD and TV. Select an appropriate video input mode on your TV until you get the initial TViX HD screen. (The S-Video cable is not included and has to be purchased separately.) 11 3.2.3 Connection to Component Output Connect the TViX HD and your TV with the component cables. Turn on the TViX HD and TV. Select an appropriate video input mode on your TV (in this case, the Component input mode). 3.2.4 Connection to DVI Output Simply connect your TViX HD to the DVI port on the TV. However, if the TV has a HDMI port only, you need to buy a HDMI cable to convert the DVI data and then you will be able to see the processing digital signal. CAUTION After you connect the video cable to your TV, press the TV Out button repeatedly on your remote control until you get the initial TViX screen. * The component cable is not included in the TViX and must be purchased separately. 12 3.3 Audio Connection 3.3.1 Connection to 2 CH Normal TV Connect the left(white) and right(red) sound output to the appropriate terminal of your TV or Hi-Fi system. 3.3.2 Connection to 5.1CH Amplifier (Digital) If you have a multi-channel decoder/amplifier with an optical/coaxial input, you can enjoy 5.1 CH high quality sound through the coaxial or optical cables. The illustration on the left shows where to connect the coaxial cable. Optical cable connection is done in a similar method. (These cables are not included in the package and must be purchased separately.) CAUTION If no sound is heard after connecting the Optical or Coaxial Cable, you have to change the audio setup of TViX to Digital. . 13 3.4 LAN Connection 3.4.1 Connect PC via Network < When connecting the computer directly to the TViX HD > Connect the LAN cable to the LAN port of both the TViX HD and the PC. TIPS In this case, you generally use a LAN cross cable type. If the computer's LAN card was connected to an Internet line, you can install an additional LAN card to your PC and connect that LAN card to the TViX. < When connecting with IP Router or Hub > Connect the LAN cable to the LAN port for an IP Router or Hub. TIPS In this case, you generally have to use Direct LAN Cable type. With NFS, M-5000U can play tp files on a PC flawlessly through LAN. We recommend NFS connection than SAMBA. You need to install TViX Netshare program on a PC but the setting became much easier SAMBA method. You can download NetShare installer from our website www.tvix.co.kr/Eng before you configure NFS network. Please refer to the Netshare program manual for detailed instructions. http://www.tvix.co.kr/eng/support/Manual.aspx You may skip the 3.4.2 section if you select to NFS network. 14 3.4.2 Set Network Configurations Under Windows XP (For SAMBA Mode) 1) Select the folder you want to share. Right-click that folder and click `Sharing and Security' in the popup menu. 2) Check `Share this folder' on the network and type in the share name `tvixhd1 (this is the only available one at the moment)'. 3) Use `Everyone' if `Everyone' is displayed, otherwise you don't have to change anything. Also, add `Everyone' to the security tab. 4) After that, the shared folder will be displayed like the following picture. 15 5) Move to 'Settings' > 'Control Panel' > 'Administrative Tools' > 'Computer Management' > 'Local Users and Groups' > 'Users', and double click `Guest'. CAUTION This is for Windows XP Professional. Windows XP Home users cannot see this window. If you cannot find `Administrative Tools' in the Control Panel, click "Switch to classic view" in the upper-left corner of the screen. 6) Uncheck `Account is disabled' 16 7) `GUEST' must be shown as the following image (a red X mark should not be shown on `Guest'). 8) Move to 'Control Panel' > 'Network connections', and select `Local area connections' properties by right clicking the mouse. 9) Remove "Guest" from the `User Rights Assignment' > `Deny access to this computer from the network' option. 17 10) Move to `Access this computer from the network', and then select `Properties' by right clicking the mouse or double clicking it. 11) Click `Add User or Group' 12) Type in "Guest" and then click the "OK" button. 13) Press OK, and Guest will be registered. 18 < When connecting Computer to TViX directly > In this case, you have to use Cross LAN cable type generally.. If the computer's LAN card was connected to Internet line, you can mount additional LAN card to your PC and connect that additional LAN card to TViX 1. Move to `Control Panel' > `Network connections', and select `Properties' properties by right click of mouse. 2. When Windows 2000 or XP, Check "Allow other network users to connect through this computer's internet connection" 3. Double click `TCP/IP->LAN card' that you want to use on your computer. You must select the additional LAN card. Check `Specify an IP address', and write `IP address' & `Subnet mask' that you want to use. Ex) IP address : 192.168.0.1 Subnet mask : 255.255.255.0 19 < When connecting with IP Router or Hub > If you have already been provided a dynamic IP address from a DHCP Server or IP Router in your local area network, you don't need to write a static IP address. Use `Obtain an IP address automatically on' or write an IP address & Subnet mask that the DHCP Server or the IP Router provides. Select `Control Panel' > `Network Connections', and select `Status' properties by right clicking the mouse. After clicking the Support tab, you should see an IP Address. (ex: 192.168.1.127) < Disable Windows Firewall > 14) Move to `Control Panel' > `Network Connections', and select `Properties' by right clicking the mouse. Click the `Advanced' tab. Disable `Internet Connection Firewall'. 15) If you use service pack 2, click `Settings' at `Windows Firewall'. 16) Check `Off' and then click `OK' 20 3.4.3 Setting Network Configurations in TViX HD 1) Press [SETUP] on the remote control to view the setup screen. On that screen, select MISC setting-Network disk and write the IP address in the Server IP. (ex: 172.28.1.70) The default is DHCP and if you want to set Static IP, you can select to change Static IP on the IP setting. If you used the DHCP you don't need to assign the IP address because it's assigned automatically. 2) If you cannot access via LAN with DHCP setting, we recommend to use the Static IP setting. 3) Select 'Control Panel > 'Network Connections', and select 'Status' properties by right clicking the mouse. After clicking the Support tab, press details, and you can see the Network connection details. Write IP address, Subnet Mask, default gateway and DNS server. You must write different IP address like below image. (ex: 172.28.1.70 172.28.1.168) Forth address is different compare with PC's IP address. 4) When the setting is successfully finished, you will be able to see the shared folder. Network Disk is supported up to 4 PC system. You can see the partition on the network icon like below image. 5) You may check for detailed usage at the TViX website (www.tvix.co.kr/Eng) 21 3.5 HDD Installation/Exchange Warning: If you change the HDD of a TViX equipped with an HDD, the warranty will be voided. Power Connector 1. Assembling the TViX HD is very easy. Just follow the instructions below: Use a driver and screw the hard disk on to the guide board. Set the jumper to `Single Master'. < Jumper Settings > The `Jumper Setting' differs according to the HDD manufacturers, so please refer to the instructions of the specific HDD provided by the HDD manufacturers. SAMSUNG Seagate IBM Western Digital 2. Open the cover case in the direction of the arrow. PULL LOCK OPEN 22 3. Place the HDD in the TViX HD board. 4. Connect the power cable and the IDE cable. When inserting the HDD, take precautions to protect the IDE cable from being damaged. POWER Cable IDE Cable 5. Close the case by pushing the cover towards the direction of the arrow and then lock it. LOCK OPEN 23 4 TViX HD Setup Menu 4.1 Audio/Video Setting This section indicates the Audio/Video settings. Setup password protection is available. You can set password to enter into setup menu. (on MISC menu inside SETUP) .This will block children changing setup accidentally. The password is 1111 Audio : Digital DTS Audio : Digital WMA Audio : Analog(PCM) AAC Audio: Analog(PCM) TV Standard : NTSC NTSC/PAL Auto Switch TV Type : 4:3 letter Box Analog(PCM) Digital Video Port : Composie/S-video Video Out Color : YPbPr Video Out Mode : 480i/576i NTSC PAL Off 4:3 letter Box 4:3 Pan-Scan 16:9 Composie/S-video Component/DVI YPbPr RGB 480i/576i 480P/576P 720P 1080i Apply Now * Audio : You can set the mode of audio output by each audio codec used. - If you set Audio to Digital, you can set DTS and WMA to digital or analog. - Please set this according to the audio format your receiver supports. * Analog : Select this when you connect the audio with a stereo RCA cable (the RED and WHITE cable) You can set the mode of audio output by each audio codec used. If you set Audio to Digital, you can set DTS and WMA to digital or analog. Please set this according to the audio format your receiver supports. * Digital : Select this when you connect the audio with an optical or coaxial cable for digital audio connection to the Decoder/Amplifier. There will be no analog audio out from the analog audio port of the TViX HD. * TV Standard : The default video setting of the TViX HD is COMPOSITE (NTSC/S-VIDEO or PAL C/SVIDEO). This is the most general setting and works with almost all TVs. * NTSC/PAL Auto Switch : is used when the video out is changed according to the NTSC or PAL format. * TV Type : 4:3 Letter Box / 4:3 Pan & Scan for ordinary TVs / 16:9 for Wide TVs like HDTV or Plasma TV. If the ratio of the TV is 4:3, select the 4:3 letter box or 4:3 Pan & Scan. If the ratio is 16:9, select 16:9. * The 4:3 Letter box can show the original ratio of the multimedia file in 16:9. 24 * The 4:3 Pan & Scan will adjust the image of the 16:9 multimedia file to the 4:3 of the TV screen by scaling the image. * 16:9 can adjust any ratio of the multimedia file to the TV screen with the original image. * Video Port : If you fail to see the initial TViX HD screen after turning the unit and TV on, make sure you have chosen the right TV out option by repeatedly pressing the TV Out button on the remote control. NTSC C/YPbPr(480i), PAL C/YPbPr(576i) is a special case. Select these settings if your TV is connected to TViX HD with a component output. * Video Out Mode : Select this when you connect the video through a component (YPbPr) cable. You can select the output resolution among 480P/720P/1080i. Setting it to 1080i will work on all HD grade TVs. YPbPr : 480i/576i, 480P/576P, 720P, 1080I,1080P(DVI) RGB(DSUB) : 480P/576P, 720P, 1080I,1080P(DVI),640*480, 800*600, 1024*768, 1280*1024 * Apply Now : After configuration, please press `Apply Now' to save the Video out state. If you want to exit the Setting, Select the EXIT button( ) and then press OK on the remote control. 25 4.2 MISC Setting This section indicates the MISC settings. Slide Show Effect : Slide Show Delay : Date / Time Setting : FAN Speed : Select Language : Autorun : OSD Display : Safety Lock: Subtitle/Outline: Screen Saver Remote Controller: Fade In/Out 5s Normal English ON Normal Disable White/Black Disable Common Enable Disable Enable Disable English Korean * Slideshow Effect : This is used when playing background music while watching picture slideshows. * Slideshow Delay : Set the slide show time interval (0 sec ­ 60 sec) * Date / Time Setting : Adjust the clock on the VFD by using the arrow and numeric keys. * FAN Speed : Select your Fan Speed. We recommend the Normal setting. * Select Language : Select your language preference. * Autorun : You can listen to music(audio files) without display(TV). If you select "random", it plays randomly. (Off-on-Random-Repeat-Random/Repeat) * OSD Display : Select the type of OSD display. We recommend the Normal mode. * Safety Lock : is used the password("1111") when you run the SETUP menu. * Subtitle/Outline: Change the color of the subtitle and its outline. * Screen Saver : If there is tvix_ss.jpg on the root directory, you can see this image(160*160 pixel) after 2~3 minutes. When the pause status or playback of audio(without slide show), Screen saver will work. * Remote Controller : You can select your remote type. We recommend the common setting. If there is a collusion between other device and TViX remote, you'd better A or B type referring to image. 26 4.3 Network Setting This section indicates the Network settings. IP Setting : Network Disk1 : Network Disk2 : Network Disk3 : Network Disk4 : TViX Network Info FTP Password DHCP Normal(NFS) Normal(NFS) Normal(NFS) Normal(NFS) 800510 DHCP Static IP Slow(SAMBA) Normal(NFS) * IP setting : Default setting is DHCP. If you cannot access via LAN with DHCP setting, use the Static IP setting. Please refer to Setting Network Configurations in TViX HD. * Network Disk : Write the PC's IP address in the Server IP. (ex: 192.168.001.128) Supports up to 4 Network disk server. There are two network method in TViX5000 model. One is SAMBA mode another is NFS mode. - SAMBA mode : You can play the file via network without special program, but the speed is lower than NFS mode. - NFS mode : You must install the TViX NetShare utility in to your PC, but you can play the TP or DVD jukebox without stutter. We recommend to share the NTFS file system. FAT32 file system does not contain enough information to create a lasting file name, so TViX doesn't load the file after changing the file name. For the detail instruction, you can download the NetShare installer and NetShare manual from our homepage. (www.TViX.co.kr/Eng) When several tvix is accessed to one PC, You must set to SAMBA setting. * TViX Network Info : You can see the information of TViX's Network. * FTP Password : If you want to use FTP function, you must use this password. For the detail instruction, please refer to following FAQ. - http://www.tvix.co.kr/eng/faq. ** Number 1 key is changed as @ : / _ - when this key is pressed. 27 5 Easy Usage of TViX HD 5.1 Play Video Files When installation is successfully finished, you will see screen A. You may copy a video file into the VIDEO folder in advance. 1. SETUP, VIDEO, AUDIO, PHOTO, HDTV icons. 2. Select the Video icon by using the Left/Right button. If you want to change the partition of the HDD, press the Jump/Repeat button. 3. After selecting the icon, press the OK button. 4. You will see 2 files in the Video folder. 5. Using the up/down button, select the Video file. By pressing the OK button, you will be able to play the video file. TIPS If you want to play the next video, press the NEXT(>>|) button. 28 5.2 Play Audio Files You may copy an audio file into the AUDIO folder in advance and play music files. 1. If you cannot see screen A, press the MENU button on the remote control. 2. Select the Audio icon on screen A and press the OK button. 3. You will see the audio file that you just copied. 4. Select the audio file using the up/down button. Then by pressing the OK button, you can easily play the audio file. TIPS If you want to play the next video, press the NEXT(>>|) button. 29 5.3 Play Image Files You may copy image files into the PHOTO folder in advance and play the image or photo files. 1. You may press the PHOTO button on the remote control without selecting from the menu screen. 2. Press the PHOTO button. 3. You can see the image files that you just copied. 4. Select the image files using the up/down button. By pressing the OK button, you can easily play the image files. 5. If you want to play the next video, press the NEXT(>>|) button. TIPS You can play the Video and Audio as well as the Photos with the remote control. If you connect the LAN cable or external USB, Network or USB icon is enabled. We're supporting up to 4 hard disk partition, 4 network PC, 4 USB1 partition and 4 USB2 partition. 30 6 Using the remote control 6.1 Basic Functions Video Folder button Show DTV button Audio Folder button Photo Folder button SETUP button Jump/Repeat button TV Guide button Previous button Navigation Arrow Button REW / FF Next button Mute button Information button OK/Selection button GOTO button Sleep button Return/File open button Change TV channels Change Volume Shuffle button Subtitle button Number/Character button File mode : 1/2/3/4 : Change Partition 6/7/8/9 : change Driver Local/Network/USB1/USB @:/_- Scroll button DVD Title button DVD Menu button TV OUT button Power button Zoom button Delete file or folder TV Record button When the File list menu, 1/2/3/4 : used to change the partition (partition 1/ partition 2/ partition 3/ partition 4) 6/7/8/9 : used to change the Drive (Local/Network/Usb1/Usb2) < Changing Batteries> - Use new batteries (2 AA size batteries are included in the package). 31 6.2 Descriptions of Each Buttons The playback of multimedia files. Basically you can choose the file you want and press the OK button. For playback of DVD files copied to the HDD, please locate the cursor to VIDEO_TS.IFO file and press OK. You can do a full DVD navigation like you would do with a DVD player. 6.2.1 Video Playback When you press the VIDEO button on the remote control, only the VIDEO folder will show on the TViX HD. This only applies to the active partition if you have more than one partition. When you press the JUMP/REPEAT button on the remote control, you can select another input source. Video File Filter You can repeat the selected section with this button. When stopped, it can be used for selecting the source. In case of 2 Audio, You can select audio File Information When playing contents, you can skip or go to the previous contents with these buttons. When stopped, it can be operated as the page up/down keys. Mute shows remaining HDD space By inputting the time you can go to the frame you want. Play/Pause Go to the Previous Menu Volume Sync of Subtitle Change the Subtitle Bookmark Screen Scroll DVD Title Screen Zoom DVD Menu Select TV Out Type. When the Play menu, you can configure the sleep time 30->60->90->120->150->180 using the Function Key. SLEEP ON will blink for 30 second before turning off. 32 INFO Button : · First Press ­ Shows information of the contents. · Second Press ­ Shows the elapsed time (the progress bar is displayed on the upper left hand corner of the screen). · Third Press ­ Show remaining time. · Forth Press - INFO off · Pressing Info button while you are not playing files shows remaining HDD space. SUBTITLE Button : · Supports SMI Multi-subtitle control with the Subtitle button. · First Press : Shows the Subtitle OSD. You can change the subtitle size using the OK button. If you press UP/Down button, you can change the position of subtitle. · Subtitle color or outline is configurable on the SETUP menu. · Supports .SUB (bitmap) + .idx subtitle files · PAL format .SUB subtitles are not supported in this version. · You can go to subtitle file selection mode by pressing TITLE button (next to MENU) on a remote controller. You can navigate folders and files and press OK button on a subtitle file you want. · You can change the subtitle sync using CH +/ZOOM Button : · First Press ­ Zoom, you can change the size by pressing the arrow buttons. · Second Press ­ Full screen · Third Press ­ PAN&SCAN full screen · Fourth Press ­ Zoom Off BOOKMARK : If you stop the movie, the stop position will be automatically saved and you can resume it later anytime by pressing the "bookmark" button on the remote control. SETUP Button · Picture adjustment. Contrast Brightness Saturation. DELETE Button : is used to delete the file or folder from the TViX Local hard disk. If you configure the remote controller lock up option on the SETUP menu, You must press the password ("1111") if you want to delete the file. When you do delete the file or folder, you must play the check disk periodically. TViX player is shown the disk check message if you need to check the hard disk.. http://www.tvix.co.kr/ENG/FAQ/FAQM5000U.aspx?act=RD&id=130&pg=0&CATID=3&SCATID=2 Sleep function has been implemented. 33 - You can set sleep time by pressing function key repeatedly on a remote controller. - SLEEP ON will blink for 30 second before turning off The present playing time will be displayed with the GOTO function. FF/REW Button · AVI : 4X 8X 16X 32X. · DVD Jukebox : 2X 4X 8X 16X 32X 64X. * Press the VIDEO button and you can filter video files among those stored in the TViX HD. TIPS * Improved to save up to eight bookmarks on eight individual files. (It cannot save eight bookmarks on a single file.) * Recognizes AVI, MPG, VOB, CAT, M2P video files only. * A video file where the folder is setup with a password cannot be saved. * When replaying the same file, only the last play position will be saved (thus, bookmarked). * Among the bookmark list, a file deleted from the hard disk will be automatically deleted from the bookmark list as well. * Cannot save the bookmark list when in USB HOST or LAN mode. < DVD Jukebox Key > - When a movie is playing it operates as a play button. In the menu screen it operates as a select button. PAGE-DOWN - Go to the next chapter. PAGE-UP - Go to the previous chapter. AUDIO Button - You can change the audio. (International dubbing, DOLBY, 2CH, 5.1CH, DTS etc.) SUBTITLE - Shows the subtitle menu. MENU Button - Shows the DVD menu screen. TITLE Button - Shows the DVD title menu. ANGLE Button - If the DVD title has an angle function, you can change the angle. GOTO Button - You can choose the time, chapter and title. After choosing you can play directly. Number + OK - Play the chapter of the number directly. ** The operation of "PICTURE" and "VOLUME UP/DOWN" is the same for Video operation. 34 OK Button 6.2.2 Audio Playback When you press the AUDIO button on the remote control, only the AUDIO folder shows in the TViX HD. It applies only to the active partition if you have more than one partition. Audio File Filter Displays the audio information being played Go to the Previous/Next Music. file Go to the designated time frame Input the time and press OK Play/Pause Stop playing and return to the previous menu. Mute. Volume. Random Play ** Some functions require firmware updates first. Press the AUDIO button and you can filter video files only among the files stored in the TViX HD. It applies only to the active partition if you have more than one partition. - Shuffle Function (Random Playback) Press the Shuffle button to play the files of the present directory randomly. Press the Shuffle button again to disable the shuffle mode. 35 Supports 10 Sec function when playing WMA, WAV files. 10 sec FF/REW function is available while playing audio files. Supports Lyric Files (.lrc) If the file name of a music file and .lrc file are the same, the lyrics will be displayed automatically. Supports ID3 TAG (ID3V1) when playing MP3 files - Press the INFO button to view the ID3 TAG (ID3V1). - You can see additional information recorded on the MP3 files, such as the artist, album etc. - OGG also displays basic Tag information m4a extension is supported. You can change the audio tracks on WMV files. Just press Audio key on the remote. When you play audio files, it will start slideshow if there are picture files on the same folder or Autojpg. · · It will check the same folder and then Autojpg folder. This is useful if you put the album art on the same folder 36 6.2.3 Image Playback Only the PHOTO folder will show in the TViX HD when pressing the PHOTO button on the remote control. It applies only to the active partition if you have more than one partition. Filter Image Files Only When playing contents, you can skip or go to the previous content with this button. When stopped, it operates as a page up/down key. Stop playing, return to the previous menu Go to the previous menu Random Play Screen Scroll Screen Zoom Rotate Image 90° Clockwise You can set the slideshow time interval at the SETUP menu. You can change the size of the picture with the ZOOM and SCROLL button. 37 Some non-standard JPEG files may not be displayed If you press the SETUP button, you will see in sequence the Contrast Brightness Saturation menus. In these menus, you can adjust the Contrast, Brightness and Saturation by pressing the left/right arrow buttons. When you see the picture files, you can play background music. It will check the Autoaudio or Automp3 folder on the root folder of current partition. If it plays background music, the large picture files may not seen due to the resource shortage. So if you want to see large files, you should not play background music. The currently supported maximum resolution of picture is 3264 * 2448. However, this result is without background music. With background music, the supported maximum size is 3072 * 2048. Support browsing by icon mode Make a empty file named as "icon.tvix" on the folder that you want to browse by icon. The file name for the file used for the icon files is case sensitive, it must be the exact same name as the media file except that the extension must be jpg or png(if you want to use transparency, set the transparency color as 0xC8C8C8.) To show the folder as icon, please put "folder.jpg" or "folder.png" on the folder. The maximum icon size is 720 * 480, and the best size is 100 * 136. 38 6.3 Extra Features 6.3.1 Using the AutoRun Function When you want to play music with the TViX HD but do not have any display devices, the following function may come in handy. 1. Make a folder and name it, "autorun" in the root directory of the First partition. 2. Copy media file(s) or make a sub-folder in the "autorun" folder. 3. If you want to change the setup, push the SETUP button on the remote control. Then go to the SETUP/MISC tab. Set AutoRun option to ON. If you set the AutoRun option to OFF, the function will not work. If you select `Shuffle,' files will play randomly. 4. After setting the configuration, turn off the TViX HD and then turn it on again. The TViX HD will play the media file from the first sub-folder under `/HDD1/autorun'. TViX HD will play files in the sub-folders first and then it will play the files in `/HDD1/autorun'. After the TViX HD plays all the media files, it will be repeated again from the beginning. 39 6.3.2 Using Wallpaper If you put a JEPG file named "TViX.jpg" under the folder which you want to change the wallpaper, the wallpaper of the folder will be changed. You can select any wallpaper you want by using the various JPEG files of different folders. If you want to change the basic wallpaper, put a JPEG file named TViX.jpg under the Root directory. You can use both lower and capital letters for the file name "TViX.jpg". 720*480 pixel is recommended for the size of the wallpaper. (A larger size may increase the loading time) In Windows XP, when you name the JPEG file, "Hide extensions for known file types" should be unchecked in the Tool-Folder Option-View-File/Folder. Otherwise the JPEG file could be named as TViX.jpg.JPG and you would not be able to see your desired wallpaper. 40 6.3.3 Playing Background Music while Watching Picture Slideshows (1) Make an autojpg folder in the HDD of TViX HD and copy image files. (2) While users are watching the picture slideshow, the MP3 files can be played as background music. Pressing 0 button, and you can see the audio list. You can select another file in there. TIPS * If the SHUFFLE button is pressed after you have begun playing MP3 files with the "Play" button, only MP3 files will play in shuffle play mode. * Slideshow delay time can be adjusted in the setup menu (press the "setup" button on your remote control) * You can stop/start the slide show using the REPEAT button.. * If you have a .lrc file, lyrics will be automatically shown. * The slideshow of picture mode. Slide once : It will stop after showing all files on the current folder Slide off : It will show the current picture and stop. To see next or previous file, you must change. Slide loop : It will loop forever. << Using WinAMP Playlist ( .m3u ) >> (1) Connect TViX to PC. (2) Open the files that is stored at TViX in " Winamp " Program. (3) Select the folder you want at Winamp after pressing SaveList, You should save the files at the same partition where the opened files were stored. (4) Disconnect TViX from PC/Mac safely. 41 6.3.4 Using Internet Radio * Notice - TViX can be connect via network - Download the .pls file or .m3u (WinAmp playlist) file. - Before play the .pls or .m3u file, you must set the network setting (DHCP or Static IP). - TViX supports only shoutcast streaming format and doesn't support other proprietary streaming formats TViX is available to shoutcast method and don't support private server. 1. Download the .pls file. You have to browse the radio station site like www.shoutcast.com SHOUTcast is Nullsoft's Free distributed streaming audio system. Thousands of broadcasters around the world are waiting for you to tune in and listen. Take a peek through the SHOUTcast directory to start browsing the most popular stations. Be sure to select your connection speed and then what kind of music you're looking for over on the right hand side for optimal listening pleasure. 2. Right click you want to play--> select Save Target As... and save the .pls file into TViX or share folder. 3. Edit the playlist file. You can edit downloaded playlist(.pls) file using the WinAMP program. 4. Run WinAMP--> Open playlist and select downloaded .pls file. 5. You can remove unnecessary items from the pls/m3u file using the PLAYLIST 6. Save the playlist to .m3u or .pls extension. 7. Point and click the .pls or .m3u file in the TViX hard disk or network share folder (ex: tvixhd1) 8. After a while, you can hear the internet radio. 42 7 Firmware Upgrade Firmware Version Check. 1. Connect the TViX HD to your TV and then turn on the TViX HD 2. Press the SETUP button on the top panel and the setup screen will be displayed. 3. Check the latest firmware version of TViX HD at www.tvix.co.kr *** You'll be posted for any firmware updates or news if you fill out the customer registration form at http://www.tvix.co.kr Downloading the Firmware. 1. Download the latest firmware from http://www.tvix.co.kr to your PC. 2. Connect the TViX HD to your PC with a USB and then turn it on. 3. Your system will recognize the TViX HD as an external hard drive. 4. Copy the latest firmware files into the root of the TVIX HD hard drive. 6. Turn off the TViX HD and bring it to your TV for firmware upgrading. How to Upgrade the Firmware 1. Connect the TViX HD to your TV 2. Select the copied firmware file (ex: TViX1.0.1.fwp) and press OK on the remote to start upgrading. 3. The following screen will be displayed. Follow the instructions on the screen. 4. Erasing the old firmware is in process. 43 5. New firmware upgrade is in process (takes about 1 minute). When the upgrade is successfully finished, the TViX HD will reboot automatically. < CAUTIONS: Safe Mode Upgrading > Even if the TViX accidentally turns off during the firmware upgrade, the safe mode will enable the TViX to be re-upgraded. Please follow the steps below: 1. Connect the TViX to your PC with a USB and then turn it on. 2. Make a tvixfw folder in your primary partition. 3. Copy the latest firmware file into the tvixfw folder of the TVIX hard drive. 4. Press the SETUP button on the top panel and turn on the TViX HD. 5. The VFD will show the copied firmware version, like HDD1/FW 1:01:00. 6. Press OK on the remote control to start upgrading. 7. The VFD will show PRE when erasing the old firmware is in process. 8. The VFD will show UPG when the new firmware upgrade is in process. 9. The TViX will automatically reboot after the upgrade has been successfully finished. 44 8 Using USB Connection with the PC TViX HD uses a 3.5" HDD as its contents storage device and works just like an external USB 2.0 hard drive when you connect it to your PC. You need to ensure that your HDD is set to master mode, and connected to the IDE cable and power cable before using it on your PC. The USB cable has a different shape on both ends. We use USB 2.0 "A" Plug (male) type to "B" Plug(male) type. After connecting to your PC, turn the power switch on. If you are a Windows98SE user, you should download a USB storage driver from our web site www.tvix.co.kr before you connect your TViX HD with your system. You do not need to install the driver under Windows ME/2000/XP. 8.1 Windows 98SE Driver Installation 1) You should download a USB storage driver from our web site www.tvix.co.kr and run installer before connecting the TViX. Press "Next" on the following pop up screen. 45 2) Press the "Finish" button to reboot. 3) After rebooting the system, connect the TViX HD. Add New Hardware Wizard will automatically pop up. 4) Select "Search for the best driver for your device" menu and then press the Next button. 46 5) Do not change any of the menus. Just click "Next". 6) As shown in the pop up the system will find DVICO USB-ATA Bridge automatically. Press the "Next" button. 7) Press the "Finish" button and the driver installation will be finished. 47 8) You will be able to see the disk drive inside the TViX HD in the Device Manager tab. < TIPS > Windows ME/2000/ XP will automatically provide the driver, so you do not have to install any extra software. Run Plug & Play when connecting the TViX HD. Right click the icon "My computer" then click properties hardware device manager to see if TViX HD has been properly installed. 48 8.2 Making a Partition and Formatting the HDDs under Windows 98SE / ME Click "Start" and select "Run" and the "Run" window will appear as shown below. Type "fdisk" in the text box of the "Run" window and then click the "OK" button. 1) The following DOS window will appear for the partition program. 2) To make a new partition, choose number 5 to select the HDD in TViX HD. 3) To make the partition for the HDD, choose the partition type and size. After selecting, make the partition. 49 4) After making partitions, do not reboot the system. Instead turn off the power of the TViX and then turn it back on. By doing so your system will reinitialize the TViX HD. 5) Run Window explorer and you will find the new disk created. Right click the new disk and choose "Format" from the pop up menu. Then start formatting your HDD in TViX HD. 50