User manual UFREE SCOOTER SCOOTER ELETTRICO FS-E07

UFREE SCOOTER www.scooter-manufacturer.com OWNER / OPERATORS MANUAL ELECTRIC SCOOTER FS - E07 A CAUTION: Read and understand this manual thoroughly before operating and handling Scooter. Please follow All safety procedures and warnings to reduce risk of electric shock! WARNING: 24V electric operated toy! Not recommended for children age under 12 years old. UFREE SCOOTER www.scooter-manufacturer.com TABLE OF CONTENTS INTRODUCTION ........................................... .......PAGE 1 ITEM IDENTIFICATION...........................................PAGE 1 SAFETY WARNINGS.................................................PAGE 2 ADJUSTMENTS AND OPERATION.............................PAGE 3-6 UNFOLDING AND FOLDING- ............ ...............................PAGE 3 HANDLEBARS......................................................PAGE 3 FOOT OPERATED POWER SWITCH.............................PAGE 4 FOOT OPERATED MECHANICAL BRAKE.....................PAGE 4 RANGE AND SPEED....................................................PAGE 4 CHARGING............................................................PAGE 4-5 SCOOTER OPERATION................................................PAGE 5 REMOVABLE PLATFORM, BATTERY ACCESS...............PAGE 6 DRIVE BELT ADJUSTMENT, REPLACEMENT................PAGE 6 BATTERY INFORMATION..........................................PAGE 7 TROUBLESHOOTING GUIDE.......................................PAGE 7 REPLACEMENT PARTS.........................................PAGE 8-9 UFREE SCOOTER www.scooter-manufacturer.com INTRODUCTION Thank you for your purchase of the Electric Scooter. The scooter will provide you with hours of fun and help you get some exercise, something we all need today. The scooter is an environmentally friendly mode of transportation since it is pollution free and whisper quiet. The scooter costs only pennies a day to operate and is completely portable with the quick fold mechanism. You can store it in the car and take it with you on the train, bus, or ferry! Your scooter will provide best results on a smooth and flat terrain. You can always assist your scooter, especially on hills, by push kicking like a traditional push powered scooter. Please be sure to operate your scooter safely and be aware of pedestrians. Be observant of all local and state laws involving scooter usage. Pay attention to ALL SAFETY WARNING and CAUTIONS noted within this manual. Following these warning and cautions will give you many hours of enjoyable and safe riding. ITEM IDENTIFICATION Before operating, familiarize yourself with these items (see fig. 1): FIG. 1A GRIPS SNAP PINS HANDLEBAR T-FRAME HEIGHT -ADJUSTER 110V INPUT, 24V OUTPUT BATTERY CHARGER QUICK-RELEASE BRAKE PEDAL AND FOLDING & LOCKING POWER CUT-OFF MECHANISM SWITCH REMOVA BLE PLAT STEERING ADJUSTMENT NUTS MOTOR BATTERY COMPARTMENT ADJUSTABLE TENSION DRIVE BELT HANDLEBARS DOWN TUBE FOOT OPERATED POWER SWITCH TOOLS REQUIRED FOR MAINTENANCE: PHILLIPS SCREWDRIVER, FLAT SCREWDRIVER, AND ADJUSTABLE WRENCH(S). (All not furnished) ALWAYS WEAR A HELMET CHARGE BATTERY AFTER EVERY USE 1 UFREE SCOOTER www.scooter-manufacturer.com WARNING BEFORE YOU ATTEMPT TO RIDE THE SCOOTER, PLEASE READ AND UNDERSTAND THE FOLLOWING: ·NEVER RIDE THE SCOOTER ON PUBLIC STREETS OR ROADS. CHECK LOCAL ORDINANCES WHERE RIDING IS PERMISSIBLE. ·MINIMUM AGE IS RECOMMENDED AT 10 YEARS OLD TO OPERATE THE SCOOTER. MAXIMUM RIDER WEIGHT IS 180LB. ·ALWAYS WEAR AN APPROVED SAFETY HELMET WHEN RIDING. BE COOL...BE SAFE! *WEAR SHOES WHEN RIDING, NEVER BAREFOOTED. ·AVOID RIDING ON GRAVEL SAND. GRASS SLICK OR WET SURFACES. SCOOTER IS DESIGNED TO BE USED ON DRY SMOOTH SURFACES. ·NEVER RIDE SCOOTER OVER CURBS OR JUMPS. THIS SCOOTER IS NOT DESIGNED FOR THIS TYPE OF RIDING. THE RETAILER, DISTRIBUTOR, IMPORTER, AND MANUFACTURER WILL NOT BE RESPONSIBLE FOR ANY INJURIES TO THE RIDER OR DAMAGES TO THE SCOOTER THAT OCCUR FROM THIS TYPE OF RIDING OR ACTIVITIES. ·POWER IS AT FULL POWER WHEN FOOT OPERATED POWER SWITCH (THROTTLE) IS ENGAGED. BE PREPARED. ·BRAKE IS DESIGNED TO CONTROL SPEED AS WELL AS FOR STOPPING. ·NEVER RIDE THE SCOOTER WITH MORE THAN ONE PERSON. MULTIPLY RIDERS COULD LEAD TO LOSS OF CONTROL. ·KEEP HANDS, FEET, HAIR, AND SHOESTRINGS AWAY FROM ALL MOVING PARTS. ·NEVER LEAVE CHILDREN UNATTENDED WITH THE SCOOTER. THIS COULD LEAD TO POTENTIAL HAZARDS! ·FAMILIARIZE YOURSELF WITH THE SCOOTER AND CHECK ALL FASTENERS FOR TIGHTNESS BEFORE EACH USE. ·DO NOT STORE BATTERIES NEAR HIGH TEMPERATURES, BATTERIES CAN EXPLODE. ·DO NOT EXPOSE CHARGER TO MOISTURE OR USE IF DAMAGED. REGULARLY CHECK THE CORD. PLUG & ENCLOSURE FOR ANY DAMAGE THE CHARGER MUST NOT BE USED UNTIL THE DAMAGE IS REPAIRED. ·NEVER OPERATE SCOOTER WHILE IMPAIRED. CAUTION: IT IS RECOMMENDED TO ALWAYS PUSH START THE SP007 TO REDUCE THE START LOAD ON THE MOTOR. YOUR SCOOTER MOTOR WILL HAVE A MUCH LONGER LIFE WITH PUSH ASSISTANCE. CAUTION: ELECTRICALLY OPERATED TOY! RECOMMENDED TRANSFORMER MUST BE USED. CAUTION: THE TRANSFORMER IS NOT A TOY! RISK OF ELECTRIC SHOCK! CAUTION: CHARGER FOR DRY LOCATION AND WDOOR USE ONLY! CHARGE BATTERY AFTER EVERY USE 2 UFREE SCOOTER www.scooter-manufacturer.com ADJUSTMENTS AND OPERATION UNFOLDING AND FOLDING Your scooter is shipped in the folded and locked position. To unfold lift the Quick Release Handle and the opposite side. Adjustable Spring Loaded Handle (fig. 2). Turn the Spring Loaded Handle. This will allow you to lift the Handlebars to the upright position. Lock the Spring Loaded Handle into the small round Guide Hole. Clamp down the Quick Release Handle. Check for a secure lock. Reverse this procedure to fold. There is Tightness control Adjustment Nut on the Spring Loaded Handle. LIFT QUICK RELEASE HANDLE ADJUSTMENT FIG.2 SNAP PINS HANDLEBARS Insert Grips into Handlebar T-Frame as shown in fig 3.Be sure that Snap Pins fit into, and lock the small holes in the top of the T-Frame. With the handlebars in the upright & locked position, and the rider standing on the platform with ONE FOOT ON THE BRAKE, adjust the Handlebar height to just below the rider's waistline. This is accomplished by loosening the Height adjuster (fig. 3) while holding onto the handlebars ...move the handlebars to the desire d height and tighten Height Adjuster. Be sure Height Adjuster is tight. RAISE HANDLEBA GRIPS R T FRAME LOOSEN LOWER TIGHTEN FIG.3 3 UFREE SCOOTER www.scooter-manufacturer.com ADJUSTMENTS AND OPERATION FOOT OPERATED POWER SWITCH (Throttle) The Scooter is equipped with a Spring-Loaded Foot Operated Power Switch located towards the front of the scooter platform (fig. 1): When depressed, the power is on and the motor and rear wheel causes the scooter to move forward. FOOT OPERATED MECHANICAL BRAKE The Rear Wheel Brake is activated by applying foot pressure to the Round Brake Pedal (fig 1) located on top of the rear end of the scooter platform. This Brake is a friction brake ...the hander you press the more braking action you will have. This Brake also has a micro switch that disconnects the power to the motor. RANGE AND SPEED When fully charged, the scooter will cover approximately 10 miles on level ground with a 100 LB. rider top speeds approximately 10MPH with a 100LB. Rider on level ground and calm winds. NOTE -These figures are estimates only, they will vary. STEERING ADJUSTMENT NUTS, BICYCLETYPE You will need to periodically check your steering for play or looseness. The steering tightness can be adjusted by turning the ROUND HAND NUT clockwise and locking with the hex niut (fig 1) CHARGING When shipped the batteries are fully charged. Charging the Batteries after every use is recommended. For extended battery life, DO NOT discharge Batteries completely before recharging. Following this simple rule: When the starts to slow down on level ground, it's time to recharge. CHARGING PROCEDURE In order -with charger in hand, locate the Charge Socket under the scooter (fig 4). Plug the charger into the Charger Socket. Next, plug the charger into a standard 110/220 volt electrical out-let. Charging temperature between 50 to 100F. DO NOT OVER-CHARGER-SEE CHART when finished unplug Charger from the wall outlet then scooter and replace cap over the charge socket. IMPORT. To insure that the batteries are fully recharged before use but are not overcharged, please follow the charging times recommended. BATTERY OVERCHARGING DOES NOT RESULT LONGER RUN TIMES. HOWEVER, OVERCHARGING DAMAGES THE BATTERIES AND REDUCES THEIR LIFESPAN. ALWAYS WEAR A HELMET CHARGE BATTERY AFTER EVERY USE 4 UFREE SCOOTER www.scooter-manufacturer.com Charging Procedure SCOOTER BATTERY CHARGING SCOOTER USETIME (BATTERDISCHARING) CHARGINGTIME (DONOTOVERCHARGE) 0 MINUTES -------------- 3-4 HOURS 20 MINUTES -------------- 5-6 HOURS 30 MINUTES-- ---------- 6-8 HOURS POWER USE REQUIREMENTS CAN VARY DEPENFING ON RIDER TRAVERSED. TIMES ARE RECOMMENDED AVERAGES. STD 110V WALL OUTLET 2 CHARGE SOCKET 1 IN ORDER: STEP 1, THEN 2 SCOOTER OPERATION FIG. 4 FIRST, ALWAYS WEAR AN APPROVED HELMET, EYE PROTECTION, SHOES AND FOR INEXPERIENCED RIDERS, WE RECOMMENDED GLOVES, KEEN AND BELOW THE PADS (fig 5). Before riding, be sure to have a clear unobstructed level path ahead of the rider firmly grab the Handlebars, place your front foot onto the platform just behind the Power Switch (BLACK BUBBLE). Go ahead and push off like a regular push scooter to engage the motor simply press the Power Switch with the front foot...To disengage the motor and to SLOE/STOP press the Brake Pedal with heel of your rear foot . UES THE BRAKE TO CONTROL YOUR SPEED. As you become a more skilled rider, you will use a combination of brake and power to achieve optimum operation. Be sure to recharge the batteries after using. ALWAYS WEAR HELMET FOOT OPERATED BRAKE FOOT OPERATED POWER SWITCH FIG.5 ALWAYS WEAR A HELMET 5 UFREE SCOOTER www.scooter-manufacturer.com ADJUSTMENTS AND OPERATION REMOVEABLEPLATFORM The Platform is removable to gain access to the Batteries. To remove, remove the four deck screws with a Phillips screwdriver (fig 6) and remove Brake Pedal and spring. Platform will lift off of Scooter Frame. Reverse procedure to replace platform. SCREW (4) PLATFORM BRAKE PEDAL SPRING CAREFULLY REMOVE SCREWS, SPRING AND BRAKE PEDAL TO GAIN BATTERY ACCESS. FIG. 6 DRIVE BELT ADJUSTMENT AND REPLACMENT Periodic adjustment of the Drive Belt is required. The Belt will become loose after hours of operation. When it does, the Belt will make a popping noise while accelerating. When this occurs, you must tighten Drive Belt immediately to tighten Belt, loosen Rear Axle Nuts slightly and rotate the Belt Adjuster Discs equally (fig. 7). Tighten Axle Nuts and recheck belt tension. If Belt is damaged or worn please contact YOUR LOCAL DISTRIBUTOR for a replacement. Be sure to specify Scooter. Rremove rear wheel from scooter to replace belt. Reassemble, see Belt Alignment. Drive Belt Alignment. lf you experience either the Drive Belt coming off the Drive Gear or Wheel Gear and/or rubbing against the scooter frame, there most likely is belt misalignment. To realign carefully place the upside down on a Sturdy surface(table, stool, etc.) and determine the direction of Belt side movement(fig.8).You will need to move the Rear Wheel left or right slightly to realign. To do this loosen Axle Nuts slightly and Rotate Belt Adjuster Discs. Tighten Axle Nuts and Check alignment by engaging power. Recheck alignment after riding-readjust if necessary. .BRAKE PLATFORM DRIVE BELT REAR WHEE LL MOTOR SIDE VIEW BELT ADJUSTMENT BELT ADJUSTER DISC(S) FIG. 7 PLATFORM DRIVE GEAR AXLE NUTS BELY ADJUSTER DISCS BELT UNDERSIDE VIEW MOTOR BELT ALIGNMENT FIG. 8 6 UFREE SCOOTER www.scooter-manufacturer.com IMPORTANT BATTERY INFORMATION BATTERY CARE 1. Store Scooter and Charge Batteries at a temperature between 50 and 100 F. The higher the temperature, the faster the Batteries will self discharge. Try to keep your Batteries charged. Inspect Batteries occasionally and keep the terminals clean & connections tight. 2. Handle your Batteries and Charger with care. DO NOT drop them. Running the Batteries completely down (discharging) will shorten their life span. DO NOT OVERCHARGE, SEE CHARGING TIMES CHART. 3. We suggest that you purchase additional batteries for extra power requirements. REPLACEMENT BATTERIES Even with proper care, rechargeable batteries will not last forever. When Batteries will not hold a charge, please call the LOCAL DISTRBUTOR. IMPORTANT: These batteries are Lead Acid based and must be recycled properly. DO NOT throw any battery into the household waste and or trash. Contact your local waste service for proper disposal. DO NOT return the scooter to the place of purchase if you encounter problems. Please check the following Troubleshooting Guide or call YOUR LOCAL DISTIRBUTOR. TROUBLESHOOTING GUIDE Problem Possible Motor Does Not Start: Rear Wheel Doesn't Turn: Motor Shuts Off During Use: 1 .Batteries not connected 2.Batteries are drained 3.Electrical fault 1. Broken drive belt 2.Motor problem 1. Circuit Breaker has tripped 2.Inadequate assistance 1. Batteries not fully charged 2. Hilly Terrain 3. Cold Batteries 4. Popping sound on accelerating 5. Damaged or Old Batteries 1. Release Throtle and wait a few minutes to cool 2.Rider needs to assist more, push kick 1. Charge Batteries 2.Push, kick more 3.Warm Batteries 4.Tighten drive belt 5.Replace Batteries Causes Action 1 .Check connectors 2. Charge battery 3.Check ALL connectors 1. Replace drive belt Insufficient Range: WARNING: DO NOT RIDE ON PUBLIC STREETS AND ROAD. ALWAYS WEAR AN APPROVED HELMET, EYE PROMION, SHOES AND APPROPRIATE SAFETY GEAR. THE SCOOTER IS DESIGNED FOR AGES 10 AND UP, A SINGLE RIDER AND NOT TO CARRY MORE THAN 180LB. CHARGE BATTERY AFTER EVERY USE 7 7/13/2004UFREE SCOOTER www.scooter-manufacturer.com 8 UFREE SCOOTER www.scooter-manufacturer.com REPLACEMENT PARTS LIST 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 PART NO. 3001 3002 3003 3004 3005 3006 3007 3008 3009 3010 3011 3012 3013 3014 3015 3016 3017 3018 3019 3020 3021 3022 3023 3024 3025 3026 3027 3028 3029 3030 3031 3032 3033 3034 3035 3036 3037 3038 3039 3040 3041 3042 3043 3044 3045 3046 3047 3048 NO. REQ'D 1 1 1 2 2 1 2 1 4 1 1 1 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1 2 1 1 1 1 2 1 1 1 1 3 1 DESVRIPTION DOWN TUBE WITH HEIGHT ADJUSTER SET HANDLEBAR T-FRAME GRIP END CAPS GRIP TUBES ELASTIC CORD GRIPS FORK TUBE AXLE BEARINGS FRONT WHEEL STEERING HEX NUT STEERING ROUBD NUT STEERING BEARINGS STEERING TUBE PIVOT PIN PIN CLIPS ADJUSTMENT NUT SPRING LOCKING HANDLE LOCKING PIN BOWLWASHER SCREW SET CLAMPING HANDLE & MAIN FRAME PLATFORM DECK BATTERY CHARGE SOCKET CIRCUIT BOARD MICRO SWITCH POWER COVER PLATE MOTOR DRIVE GEAR MOTOR SPACE DRIVE BELT BRAKE PEDAL BRAKE SPRING BATTERIES CHARGER SWTICH BRACKET MICRO SWITCH, BTAKE BRAKE SHOE BELT ADJUSTER REAR AXLE RIGHT AXLE SPACE LEFT. AXLE SPACE REAR WFEEL AND SCREWS KICK STAND * SPECIFY CHROME OR PAINTED, IF PAINTED SPECIFY COLOR. 9 IF YOU HAVE ANY PROBLEMS£¬ FIRST CALL YOUR LOCAL DISTRIBUTOR TO OBTAIN SERVICE AUTHORIZATION. All repairs and/or replacements will be performed or processed through the LOCAL DISTRIBUTOR. AII returning Scooters and or Parts must have preauthorization to do so. Unauthorized returns will not be processed. Thank you for reading and understanding this manual. ALWAYS RIDE SAFELY AND ENJOY YOUR RIDING! WE ARE ALWAYS LOOKING TO IMPROVE OUR PRODUCTS AND WE WELCOME YOUR COMMENTS. AGAIN, THANKYOU FOR PURCHASING THE ELECTRIC SCOOTER WARNING 1. T0 KEEP THE BATTERY LIFE, THE SCOOTER CAN'T BE USED BECAUSE THE ELECTRIC POWER CONNECTOR IS NOT CONNECTED. 2. CAREFULLY REMOVE SCREWS, AND THEN OPEN THE PLATFORM (FIG 1). 3. TAKE OUT THE WHITE PLASTIC AND INSERTTHE ELECTRIC POWER CONNECTORS (FIG 2). 4. C0VER THE PLATFORM, THEN SCREW ON, AND YOU CAN USE THE SCOOTER IMMEDIATELY (FIG 1). SCREWS BRAKE PEDAL SPRING PLATPORM ELECTRIC CAREFULLY REMOVE SCREWS.SPRING AND BRAKE PEDAL TO GAIN BATTERY FIG. 1 FIG. 2