UFREE SCOOTER www.scooter-manufacturer.com ELECTRIC SCOOTER FS ­ E11 UFREE SCOOTER www.scooter-manufacturer.com INSTRUCTION 1. Safety caution Please follow all the instructions mentioned in this manual and operate it correctly. 1.1 To ensure your and other people's safety, please obey all traffic rules and regulations, the user should ride it on the slow lane without taking anybody. 1.1.2 To ensure this scooter to have a long life, please read the manual instructions before your operation to this scooter. Don't lend it to the people who can't operate this scooter correctly. 1.1.3 Since the speed is fast, please be careful to use it in the snow or rain weather, have a brake in advance when braking is necessary. 1.1.4 Without adult's supervision, minors mustn't operate this scooter. 1.2 Operation instruction 1.2.1 To check if the scooter is in good situation. 1.2.2To turn on the switch, the power light is on; it means the power is connected. 1.2.3 To hold two handle bars, lift the kickstand off the ground, turn the right accelerator at anticlockwise movement slowly, the scooter will speed up. 1.2.4 This scooter has the function of braking with power disconnect, when riding, use the brake to disconnect the power if necessary, and ensure to be safety. 1.2.5 When the volt of battery is lower 20.5V, the warning "beep" is sounding, please stop riding and charge soon. 1.2.6 When finishing ride, please turn off the switch and put down the kickstand. 1 UFREE SCOOTER www.scooter-manufacturer.com 1.3 Charge instruction 1.3.1 To avoid damaging the battery, it is a must to use the charger appointed to charge the battery. 1.3.2 To confirm the charger input voltage in accordance with the socket voltage, then connect, if the red and green light in the charger are on, it means the power is connected. When the red light is becoming green, indicate the battery is full. 1.3.3 Charge time is not more than 18 hours. 1.3.4 To finish charge, please disconnect the power and unplug the charger plug. 1.3.5 Before storage, please charge the scooter fully; also suggest to charge the scooter per month. 1.4 Caution: 1.4.1 When riding on the smooth road at low windy speed, under the safety condition, should not stop and start the scooter frequently. 1.4.2 To ensure the battery to be in good condition, please charge it in time after your riding. 1.4.3 Should not start up the scooter frequently on the grade road. 2. Frame and instruction 2.1 This scooter is equipped with the battery of high power and lead-acid free of maintenance. The battery is located in the best place, make the gravity point low, and insure the balance & safety to the rider. 2.2 This scooter is equipped with the electric driving control non-grade HUOER accelerator system, which can protect the motor and battery effectively and have a safety operation. 2 UFREE SCOOTER www.scooter-manufacturer.com 2.3 One special full automatic charger is used to this scooter, which can avoid overcharge. 3. Main technical parameter and function index 3.1 Entire scooter specification: Max speed: 12.5 miles/hour Range per charge: 10 miles Max load: 200 lbs Incline capacity: approx. 4° Net weight including battery: 45 lbs Tyre: 12" pneumatic 3.2 Motor parameter: Rated power: 250W-350W Rated volt: 24V 3.3 Battery: Type: high power lead-acid storage battery free of maintenance Current: 12AH Voltage: 12Vx2 3.4 Charger: Input volt: 110-220V Charge time: 6-8H 4. 4.1 Assemble and adjust method Assemble 4.1.1 Take out the scooter from the carton. (Figure 1) 4.1.2 Loose the flat bolt in the handle bar, remove the pin and insert the connector to handle bar, then insert the pin shaft, tighten the bolt, turn and tighten the folding unit to steady the handle. (Figure 2) 3 UFREE SCOOTER www.scooter-manufacturer.com Assemble the handle bar, put the accelerator correct location, fix it with hex spanner. (Figure 3) 4.2 Assemble the saddle pipe, adjust and tighten. (Figure 4) 4.3 Adjust the rear brake 4.3.1 Adjust the rear adjusting bolt, tighten the brake bar to insure rear wheel not turning, loose the brake bar, rear wheel turning freely. (Figure 5) 4.3.2 If brake shoe (brake rubber) wear-tear too much, please replace it in time. 4.4 Front wheel assembly, maintenance and service. 4.4.1 Loose the front shaft nut, remove the special washer to the hole (O6.5), tighten front shaft nut, insure the front wheel in correct location. (Figure 6) 4.5 Adjust the chain 4.5.1 Loose the rear shaft nut. 4.5.2 Loose the bolts on both sides, move the rear wheel backside, adjust and make the chain running freely, tighten rear shaft nut. (Figure 7) 4.6 Assembly the rear wheel 4.6.1 Loose the rear shaft nut, put off the chain, take out the rear wheel. 4.6.2 Put the chain, adjust the bolts on both sides, finally, tighten the rear shaft nut. (Figure 8) 5. Maintenance and service 5.1Daily inspection and service 4.1.3 4 UFREE SCOOTER www.scooter-manufacturer.com 5.1.1To make sure if the motor has the clash, noise etc. Abnormal phenomenon while running, please repair it in time if necessary. 5.1.2To check if all parts and connectors are fixed well. 5.1.3To check if the brake works well, any problem, please adjust or replace. 5.1.4To check if all control and stay lines are perfect & flexible. Should not have any jamming phenomenon. 5.1.5To check the pressure of two wheels to be up to instruction. 5.1.6 Please clean the scooter after use. 5.2 Regular inspection and maintenance Please fill the front & rear axle, chain wheel etc. with lubricant regularly. Chart 1 term inspection and maintenance 300miles 600miles 1200miles 1800mile Brake A I A I Different control L I L I Tyre I I I I All the connect lines I I T I Front fork and frame I I I I Note: I-inspection, clean and adjust T: tighten A: adjust L: lubricate 5 UFREE SCOOTER www.scooter-manufacturer.com 6. Troubleshooting Please see the chart 2. Chart 2: troubleshooting Numb Troubles Reason 1 The speed control 1. The battery is order or the 2. The magnet steel is lower than l0km/h. mechanism steel cable is loose. 3. The spring of jamming or loosing 2 The electric 1. The battery wire is rotating after 2. The magnet steel power supply. mechanism steel cable is loose. 3. The wire plug of machinery is loose 4. Burn out the blown 5. Lead wire of the broken. 3 The driving distance 1. The type is short of of the requirement 2. Failure of the charged once. 3. Failure of 4. The battery is aged 5. Charging and new battery is 6. Many ascents, low heavy wind, the road surface isn't weight is over 200 Over many brake 4 The charger can't be 1. The charging 2. Fuse burned out. 3. The lead of the 5 No displaying of the 1. Start the electric charging state of the see if the battery and the electric than 20.5V; can't start. 2. The battery bus is Removing Fully charge the Clamp it after Replace the spring. Repair and Clamp after Repair and replace; Replace the blown Reconnect. Fully charge the Repair the charger; Change the Change the battery; Continually using battery, charge and it more than 10 Tighten the run-in; Change the blown Reconnect. Replace a new Reconnect and 6 UFREE SCOOTER www.scooter-manufacturer.com Horn switch Head light Accelerator Saddle Brake Turning light switch Switch panel 7 UFREE SCOOTER www.scooter-manufacturer.com 8 UFREE SCOOTER www.scooter-manufacturer.com E-SCOOTER Figure 2 Figure 3 Figure 4 Figure 5 9 UFREE SCOOTER www.scooter-manufacturer.com E-SCOOTER Figure 6 Figure 7 Figure 8 10 ...