User manual ULINE ECHELON 2015R - INSTALLATION GUIDE

TM Installation Guide 2015R -- Refrigerator www.U-LineService.com Phone (414) 354-0300 · FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 · FAX (414) 354-5696 OnlineService@U-Line.com ©2005 U-Line Corporation 02/2005 2015R -- Refrigerator TM Contents Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Swing/Clearances Information . . . . . . . . . . . . . . Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . Side-By-Side Installation Instructions . . . . . . . . . . . . . . Custom 1/4'' Door Panel Insert . . . . . . . . . . . . . . . . . . . Full Overlay Door Panel . . . . . . . . . . . . . . . . . . . . . . . . . Checking Door Alignment . . . . . . . . . . . . . . . . . . . . . . Adjusting Door Alignment . . . . . . . . . . . . . . . . . . . . . . Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . Leveling Information . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation of the 2015R . . . . . . . . . . . . . . . . . . . . . . . . Relocating the Shelves . . . . . . . . . . . . . . . . . . . . . . . . . Installation Troubleshooting . . . . . . . . . . . . . . . . . . . . . Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Start-Up Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 5 5 5 6 7 7 8 12 12 13 13 13 14 14 14 15 15 16 1 Follow Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit. · This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes. Safety Alert Definitions Safety items throughout this guide are labeled with a Danger, Warning or Caution based on the risk type: DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death. WARNING Warning means that failure to follow this safety statement could result in serious personal injury, or death. CAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury, property or equipment damage. www.U-LineService.com 2 02/2005 TM 2015R -- Refrigerator General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: 2 Inspect and Plan You have received a carton containing your 2015R Refrigerator with a package inside containing a User Manual and a Product Registration Card. Complete and mail the Product Registration Card or register online at www.U-LineService.com. Once your unit is installed, keep the User Manual and this Installation Guide in a safe place for future reference. Your unit is Black, White or Stainless Steel. Black and White units have a reversible door with a slightly contoured handle across the top. They come with a flush mounted door panel that, when removed, will accept a custom 1/4-inch thick door panel or a 3/4-inch thick full overlay door panel. Stainless Steel units are covered with a protective coating and have been ordered left- or righthand hinged. The Stainless doors are not reversible and do not accept custom panels. Please carefully follow the directions that apply to your unit and your intended design. WARNING SHOCK HAZARD -- Electrical Grounding Required. · Keep the unit unplugged throughout installation except during testing. · Never remove the round grounding prong from the plug and never use a two-prong grounding adapter. · Never use an extension cord to connect power to the unit. · Always keep your working area dry. CAUTION · Use care when moving and handling the unit. Use gloves to prevent personal injury from sharp edges. · Do not lift the unit by the door or door handle. · Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille, which may cause the unit to malfunction. Tools/Materials Required · 7/64" Allen wrench · Screwdrivers -- slotted and Phillips head · 1/4-inch thick door panel material and cutting tools (Black or White units) · Full Overlay Door Panel Kit (part number U-OL2015B -- Black or part number U-OL2015W -- White), 3/4-inch door panel overlay, cutting tools, drill and bits (Black or White units) Inspection Unwrap and inspect the unit on a flat, level surface capable of supporting its entire weight. Removing Protective Coating (Stainless Steel Units Only) When inspecting/installing a Stainless Steel unit, the protective coating covering the unit must be removed first. Start at a corner of the unit/door and pull back the protective coating to remove it from the unit/door. 02/2005 3 www.U-LineService.com 2015R -- Refrigerator TM After all the protective coating has been removed from the unit/door, clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft cloth. Do NOT use abrasive cleaning agents. Note: If cleaning with mild detergent and warm water solution and soft cloth, the unit MUST be treated with Claire Stainless Steel Polish and Cleaner or comparable product to prevent discoloration. 3 Prepare Site Your U-Line product has been designed for either freestanding or built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for electrical connection in the rear. Note: Unit can NOT be installed behind a closed cabinet door. Exterior Cleaning (As Required) Black and White Models: · The door, grille and cabinet may be cleaned with a mild detergent and warm water solution. Do not use solvent-based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft, clean towel to prevent water spotting. Stainless Steel Models: · Stainless steel models can discolor when exposed to chlorine gas, pool chemicals, salt water or cleaners with bleach. · Keep your stainless steel unit looking new by cleaning with a good quality all-in-one stainless steel cleaner/ polish on a monthly basis. For best results use Claire Stainless Steel Polish and Cleaner, which can be purchased from U-Line Corporation. (The part number is 173348.) Comparable products are acceptable. Frequent cleaning will remove surface contamination that could lead to rust. Some installations may require cleaning on a weekly basis. · Do not clean with steel wool pads. · Do not use cleaners that are not specifically intended for stainless steel (this includes glass, tile and counter cleaners). · If any surface discolors or rusting appears, clean it quickly with Bon-Ami or Barkeepers Friend Cleanser and a non-abrasive cloth. Always clean in the direction of the grain. Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems. · Use of abrasive pads such as Scotchbrite will cause the graining in the stainless to become blurred. · Rust that is allowed to linger can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible. Cut-Out Dimensions 34-1/4" to 35-1/8" 7" 23-1/4" 1" Figure 1 Follow the cut-out drawing in Figure 1. The 15-3/16" width allows 1/4" for ease in installation and removal of the unit. 24" is the counter depth in most installations. The unit is 23-1/4" deep including the handle on Black and White models and 23-1/4" deep including the door and not the handle on Stainless Steel models (see Figure 2). www.U-LineService.com 4 02/2005 TM 2015R -- Refrigerator Product Dimensions 23-1/4" Including Handle 25-3/8" Including Handle Reversing the Door (Black and White Units Only) All U-Line units (except Stainless Steel models) may be left- or right-hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side. The top hinge hardware will be used on the bottom of the other side and the bottom hinge hardware will be used on the top of the other side (see Figure 4). To reverse the door: 1. Remove top hinge screw pin from door (7/64" Allen wrench or Phillips screwdriver, depending Figure 4 on your unit's construction) (see Figure 5). Remove door by tilting forward and lifting off bottom hinge pin. 2. Remove plastic screw plugs (3 each, top and bottom) from new hinge location. Do not discard (see Figure 6). 34-1/8" 34-1/8" 14-15/16" Black and White 14-15/16" Stainless Steel Figure 2 Please note that the unit has adjustable feet that can add one additional inch to height during leveling or to match adjacent cabinets (see Figure 32 on Page 13). Door Swing/Clearances Information Black and White units have a zero clearance for the door to open 90° (see Figure 3). Stainless Steel models require a minimum of 2-1/8" door clearance to accommodate the handle if the unit is installed next to a wall or similar type of structure. Screw Plugs Wall 1/4" Min. Wall 2-1/8" Min. Figure 5 Figure 6 3. Remove top hinge (3 screws), reinstall hinge screw pin, and remount on opposite side BOTTOM (see Figure 7). 21" 21" 16-1/2" 90° Door Swing 90° Door Swing 16-1/2" Black and White Stainless Steel Figure 3 02/2005 5 www.U-LineService.com 2015R -- Refrigerator TM 4. Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge (see Figure 8). Other Site Requirements Power Supply The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). See Electrical Specifications on Page 13. Hinge Screw Pin Door Closer Inserts Environmental Requirements The surrounding air temperature must be at least 50°F (10°C) but must not exceed 110°F (40°C). Black and White units may be installed outdoors in a covered area. Stainless Steel 2015R units are deemed suitable for outdoor use by UL. The unit must not be located near heat-generating equipment or in direct sunlight. Figure 7 Figure 8 5. Remove existing bottom hinge (3 screws) and remount on opposite side TOP. Remove hinge screw pin. 6. Remove the plastic hole plug from the top of the door to allow the pivot pin to be inserted in the new location. Install the plug into the vacated hole on the opposite side. 7. With bottom of door facing up, remove pivot plate (2 screws), flip over, and remount on opposite side of door (see Figure 9). Be sure notch in plate faces center. Figure 9 8. Holding door upright with top of door tilted forward, place hole of door pivot plate on bottom hinge screw pin (see Figure 10). 9. Tilt top of door into position in top hinge and install top hinge screw pin. 10. Install plastic screw plugs removed in Step 2 in old hinge holes (3 each, top and bottom). Figure 10 www.U-LineService.com 6 02/2005 TM 2015R -- Refrigerator Side-By-Side Installation Instructions For a complete refreshment center, install your 2015R Refrigerator beside a U-Line Ice Maker, Combo, or Wine Captain Model (see Figure 11 for typical cut-out). Note that each Side-By-Side Installation will be different. · Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit's Installation Guide. For example: Placing a 2015R Refrigerator next to a 2015 series unit would require a cut-out width of: 15-3/16" + 15-3/16" = 30-3/8" Placing a 2015R Refrigerator next to a 2075 series unit would require a cut-out width of: 15-3/16" + 24-3/16" = 39-3/8" · No trim kit is required. However, 1/4-inch space needs to be maintained between the units to ensure unobstructed door swing. · Units must operate from separate, properly grounded electrical receptacles placed according to each unit's Electrical Specifications. Typical Side-By-Side Cut-Out 4 Prepare and Install Door Panel (Black and White Units Only) Two types of custom door panels can be installed on your Black or White unit to harmonize with or accent the surrounding décor: a Custom 1/4" Insert or a Full Overlay. If no custom door panel is used, go on to 5 Adjust Door. Custom 1/4'' Door Panel Insert Door Panel Preparation A custom door panel can be inserted into the doorframe. Custom door panels can be flat or raised, as long as the maximum panel thickness where inserted into the door reveal (channel) is 1/4"-thick. For raised panels, the depth of the reveal is 1/4" on all four sides. IMPORTANT Raised panels will reduce the door's 90° swing/zero clearance if the unit is installed next to a wall or similar type of structure (see Page 5). Cut the panel insert to the following dimensions. Custom 1/4" Dimensions: Width: Height: 14-1/32" 28-5/32" The door panel must not weigh more than 20 lbs. Door Panel Installation Install the insert as follows: 1. Remove the door shelves by first pulling shelves up at a 45° angle then straight out (see Figure 33 on Page 14). 34-1/4" to 35-1/8" 7" 1/4" Space Between Appliances 23-1/4" CAUTION Use care when handling the insert. Insert edges may be sharp. 2. Remove top hinge screw pin (7/64" Allen wrench or Phillips screwdriver, depending on your unit's construction, see Figure 12). Remove door by tilting forward and lifting off bottom hinge pin. 1" Figure 11 02/2005 7 www.U-LineService.com 2015R -- Refrigerator TM Full Overlay Door Panel Door Panel Preparation A full overlay door panel completely covers the doorframe and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit (P/N U-OL2015B -- Black or P/N U-OL2015W -- White). Appropriate hardware, Modified Handle, Replacement Hinges and a copy of these instructions will be included in the kit. 1. Cut the overlay to the following dimensions (see Figure 15). Full Overlay Dimensions: 3. Pull door gasket out of groove (top edge of door only). Start in the middle and pull outward, moving toward the edge (see Figure 13). This may take some force. Do not remove the three screws behind gasket. 4. Remove two outside screws holding door handle. Slightly separate door handle from door (see Figure 14). 5. Pull handle up and off. 6. Remove and discard existing panel and cardboard spacer. 7. Slide custom door panel insert into 1/4-inch channel in door front. 8. Holding door gasket out of the way, replace handle Figure 14 on door, making sure it is seated properly on insert and that screw holes line up. 9. Install two small screws removed in Step 4. 10. Starting at the corners and working inward, push door gasket into place on door. 11. Place door on bottom hinge pin and install upper hinge screw. 12. Reinstall the door shelves by lining up the bosses and first pushing straight in, then down at a 45° angle (see Figure 33 on Page 14). Go on to 5 Adjust Door. Figure 15 14-3/4" 1/8" 1/8" Figure 12 Figure 13 Width: Height: 14-3/4" 29-7/8" The door panel must not weigh more than 20 lbs. 3/4" 13/16" Relief Notch for Pivot Plate Rear View of Wood Panel 29-7/8" IMPORTANT Rear View of wood panel for right-hand hinge shown. Use mirror image for left-hand hinges. 2. Create a relief (see Figure 15) for pivot plate by cutting notch in top corner and coinciding back corner of overlay panel. Refer to Figure 16 for exact specifications. www.U-LineService.com 8 02/2005 TM 2015R -- Refrigerator 13/32" 0.177" Dia. (#16 Drill) x 11/16" Deep 3/8" 13/32" 4. Drill hole for upper door hinge (top of panel) (see Figure 16, Top View). 0.177" diameter (#16 drill) x 11/16" deep 5. Drill hole for lower door hinge (see Figure 16, Bottom View). 5/16" diameter x 1/4" deep 3/8" 13/16" Top View Door Bottom: 5/16" Dia. x 1/4" Deep Chamfer 1/32" x 45° Bottom View CAUTION 1/8" 13/32" 1/32" R 1/8" 1/8" It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed. 13/16" 1-17/32" 7/16" Installation Instructions Removing Existing Door 1. Remove the door shelves by first pulling shelves up at a 45° angle then straight out (see Figure 33 on Page 14). 3/4" Side View 1/8" R 5/16" Dia. x 1/2" Deep 13/16" Back View Figure 16 Route notch in top corner of overlay panel as shown (see Top and Side Views). Top of notch is entire depth of panel, front to back. Width: 13/16" Depth: 1/8" Route notch in backside of top corner of overlay panel (see Back and Side Views). Width: 13/16" Depth: 1/8" Height: 1-17/32" from top edge of panel (less 1/8" for depth of notch on top of panel) Radius of corner notch: 1/8" (see Back View) 3. Drill holes for pivot plate mounts (see Figure 16, Back View). 5/16" diameter x 1/2" deep, from the routed surface 2. Remove top hinge screw pin (7/64" hex key or Phillips screwdriver, depending on your unit's construction). Remove the door by tilting forward and lifting off the bottom hinge pin. 3. Pull door gasket out of the groove (top edge of door only). Start in the middle and pull outward, moving toward the edge (see Figure 17). This may take some force. New Handle Old Handle Figure 17 Figure 18 CAUTION Be careful not to drill too deep! Drilling holes too deep may destroy your door panel. 4. Remove the three screws located on the back of the handle (see Figure 18). 02/2005 9 www.U-LineService.com 2015R -- Refrigerator TM 5. Remove the top handle and discard. (This handle will be replaced with the Modified Handle included in the Full Overlay Door Panel Kit.) 6. Remove the two screws located on both sides of the lower handle. Remove the handle. 7. Attach the Modified Handle to the lower handle using the three screws removed in Step 4. Set aside. 8. Slide the existing door panel out of the doorframe. Attaching the Full Overlay Panel 1. Tap nylon inserts into the top holes drilled in the overlay panel. Use two #6 screws to attach top pivot bracket to the overlay panel (see Figure 19). Rear View of Wood Panel Drill 5/32" x 3/8" Deep for use with #10 x 5/8" Wood Screw and Nylon Spacer ­ 6 Places 27" ± 1/4" 14-5/16" ± 1/4" Typical Wood Panel 1" ± 1/8" Top Pivot Plate 8 mm Plug Insert Two Required #6 X 5/8" Flat Head Screw Two Required 1" ± 1/32" 1" ± 1/32" Figure 21 4. Attach the door panel to the overlay panel using #10 x 5/8" wood screws and nylon spacers. The nylon spacers fit between the overlay panel and the door panel as shown in Figure 22. The spacers allow the original door panel to slide back into the 1/4"-thick door reveal (channel). Figure 19 2. Place and tape the existing door panel on the back of the overlay panel (see Figure 20) and drill holes through both panels according to Figure 21. Remove tape adjoining the panels and enlarge the six holes in the overlay panel using a 0.201" (#7) drill. 3. If a user-supplied cabinet handle will be used, attach its hardware to the overlay panel at this time. Typical Wood Panel Top Pivot Plate Door Panel Back of Wood Panel Tape Removed Door Panel #10 x 5/8" Round Head Screw Six Required Plastic Spacer Six Required Figure 22 Side of Wood Panel 5/16" Bottom 3/8" Both Sides Bottom of Wood Panel Figure 20 www.U-LineService.com 10 02/2005 TM 2015R -- Refrigerator 5. Remove the existing bottom pivot plate and replace with the Full Overlay pivot plate (see Figure 23). 4. Replace the door closure assembly onto the bottom pivot post (see Figure 25). Be sure that bosses on closers align with holes in hinge and hinge plate. Existing Door Existing Bottom Pivot Plate (Remove and Discard) Wood Panel Bottom Pivot Plate (5/8" Longer Than Existing Bottom Pivot Plate, Flush Side Facing Out) #8-32 x 3/8" SEMS Hex Screw Two Places Door Closure Top Door Closure Bottom Boss Existing Door Figure 23 IMPORTANT Door panel and overlay panel must be aligned properly or the door will not operate correctly. Assembling the Door 1. Install the assembled panel by sliding the original door panel back into the doorframe. 2. Replace the two-piece Modified Handle assembly and secure with the two screws removed in Step 6 under Removing Existing Door. 3. Starting at the corners and working toward the center, push the door gasket back into place. Installing the Door 1. Remove the existing hinges from the unit, saving the door closure assembly. 2. Install the new Replacement Top Hinge onto the unit (see Figure 24). Figure 25 Boss #8-32 x 1/2" Flat Head Screw Three Places Wood Panel Bottom Hinge Plate (5/8" Longer than Existing Bottom Hinge Plate) Pivot Post IMPORTANT Pivot posts must be cleaned. Closers must also be clean and greased to ensure proper operation. 5. Place the modified door onto the pivot post. 6. Position door and install the pivot post into the top hinge (using the 7/64" hex key or Phillips screwdriver). 7. Adjust door as needed for proper closure. 8. Reinstall the door shelves by lining up the bosses and first pushing straight in, then down at a 45° angle (see Figure 33 on Page 14). Go on to 5 Adjust Door. Pivot Post Wood Panel Top Hinge Plate (5/8" Longer than Existing Top Hinge Plate) #8-32 x 1/2" Flat Head Screw Three Places Top Pivot Plate Door Panel Figure 24 3. Install the pivot post into the new Replacement Bottom Hinge (using the 7/64" hex key or Phillips screwdriver) and install the hinge onto the unit. 02/2005 11 www.U-LineService.com 2015R -- Refrigerator TM 5 Adjust Door Checking Door Alignment The unit's door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation. Slotted Mounting Holes Notch IMPORTANT Properly aligned, the door should be 1/8" below the top of the unit's cabinet, NOT flush with the top (see Figure 26). Raise Outside Door Edge Lower Outside Door Edge Figure 28 1/8" Figure 26 1. Compare the top edge of the door to the top edge of the cabinet. 2. If the door edge is 1/8" below and parallel to the top of the cabinet, go on to 6 Prepare Power Supply. If it is not, note whether the side opposite the hinge needs to be moved UP or DOWN, and use the following procedure. Note: If door is adjusted correctly, but panel is not square with the adjacent cabinets, slight adjustments can be made by drilling the holes in the vinyl coated steel panel slightly oversized. See Figure 21 on Page 10. 3. See Figure 28. If the top far edge of the door needs to move UP, move the hinge plate toward the outside of the door and retighten screws. If the top far edge of the door needs to move DOWN, move the hinge plate toward the inside of the door and retighten screws. 4. Mount the door to recheck alignment and repeat Steps 2 and 3 if further adjustment is necessary. 5. When top edge of door is parallel to top edge of cabinet, remove the door and ensure the two screws are secure. 6. Remove the door closers from the bottom hinge, clean thoroughly and lubricate the mating surfaces with petroleum jelly. 7. Reinstall the closers, lining up the bosses with holes in hinge and hinge plate (see Figure 29). 8. Mount the door, install top hinge pivot pin and go on to 6 Prepare Power Supply. Door Closer Inserts Adjusting Door Alignment 1. Remove top hinge screw pin (7/64" Allen wrench or Phillips screwdriver, depending on your unit's construction, see Figure 27). Remove door by tilting forward and lifting off bottom hinge pin. 2. With door upside-down, loosen but do not remove Figure 27 the two screws on the door's bottom hinge plate. Boss Figure 29 www.U-LineService.com 12 02/2005 TM 2015R -- Refrigerator 6 Prepare Power Supply 7 Level the Unit Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current). An individual, properly grounded branch circuit or circuit breaker is recommended. GFCI (ground fault circuit interrupter) is usually not required for fixed location appliances and is not recommended for your unit because a GFCI could be prone to nuisance tripping. However, be sure to consult your local codes. See Figure 30 for recommended receptacle location. Leveling Information Note: It is recommended that the unit is level. 1. Use a level to check the levelness of the refrigerator from front to back and from side to side. Level should be placed along top edge and side edge as shown (see Figure 31). Check Level Figure 31 2. If the refrigerator is not level, adjust the feet on the corners of the unit as necessary (see Figure 32). 23-1/4" 7" Turn Foot to Adjust 1" Figure 32 Figure 30 3. Check the levelness after each adjustment and repeat the previous steps until the unit is level. Go on to 8 Install the Unit. WARNING SHOCK HAZARD -- Electrical Grounding Required. · Never remove the round grounding prong from the plug and never use a two-prong grounding adapter. · Never use an extension cord to connect power to the unit. Go on to 7 Level the Unit. Installation Tip If the room floor is higher than the floor in the cut-out opening, adjust the rear feet to achieve a total unit rear height of 1/8" less than the opening's rear height. Shorten the unit height in the front by adjusting the front feet. This allows the unit to be gently tipped into the opening. Readjust the front feet to level the unit after it is correctly positioned in the opening. 02/2005 13 www.U-LineService.com 2015R -- Refrigerator TM 8 Install the Unit Installation Troubleshooting Installation of the 2015R 1. Plug in the power cord. 2. Gently push the unit into position. Be careful not to entangle the electrical cord. 3. Re-check the leveling, from front to back and side to side. Make any necessary adjustments. The unit's top surface should be approximately 1/8" below the countertop. Q: Problem The door remains open unless it is pushed closed. A: Solution The hinges should be self-closing when the door is open approximately 8". If this is not the case, make sure the closers (at the bottom of the hinge pin) are clean, greased and installed correctly. Also, re-check leveling from front to back of the unit and readjust if necessary. Make sure that pivot plate is installed correctly. Relocating the Shelves Both the glass shelves in the refrigerator and the inner door shelves can be moved to accommodate your bottles, cans and containers. Q: Problem The custom overlay door was designed to align with the rest of the cabinet doors, but the unit has crept forward. Glass Shelves 1. Open door fully, grasp shelf firmly, lift front edge slightly, and pull straight out. 2. Choose new location and slide shelf onto the appropriate rib. A: Solution Make sure that the electrical cord is not obstructing the installation. Door Shelves 1. First pull shelf up at a 45° angle, then straight out (see Figure 33). 2. Choose new location and line up on bosses. First push straight in, then down at a 45° angle. Notch Boss Figure 33 www.U-LineService.com 14 02/2005 TM 2015R -- Refrigerator 9 Start-Up for the First Time Start-Up Troubleshooting Initial Start-Up The unit is shipped with the control preset. No adjustments should be necessary at this time. For information about Adjusting the Temperature Control, see the User Manual. Q: Problem Unit does not appear to turn on when switch is set to ON. A: Solution Make sure unit is plugged in and outlet has power (circuit breaker has not tripped). Check to see that light switch actuator bracket is contacting the light switch properly. IMPORTANT See the User Manual's Troubleshooting Guide for more solutions. 02/2005 15 www.U-LineService.com TM Who to Call Service Information If the need for service arises, contact the dealer from whom the unit was purchased. State the Model Number and Serial Number and explain the problem. The Model and Serial Number plate is located inside unit at upper right hand corner. If you need to locate a service company, you can go online at www.U-LineService.com and search for a service company by zip code. For more than four decades, U-Line has distinguished itself as the leader in built-in undercounter ice making, refrigeration and wine storage appliances. U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in undercounter icemakers, Combo® icemaker/refrigerators, Wine Captain® wine storage units, refrigerators, refrigerated drawers and refrigerator/freezers. ©2005 U-Line Corporation Publication No. 30057E 02/2005 Rev. A