Precautions Before you use this scanner, please read and observe the following. IMPORTANT! This scanning radio has been manufactured so that it will not tune to the radio frequencies assigned by the FCC for cellular telephone usage. The Electronic Communications Privacy Act of 1986, as amended, makes it a federal crime to intentionally intercept cellular or cordless telephone transmissions or to market this radio when altered to receive them. The installation, possession, or use of this scanning radio in a motor vehicle may be prohibited, regulated, or require a permit in certain states, cities, and/or local jurisdictions. Your local law enforcement officials should be able to provide you with information regarding the laws in your community. Changes or modifications to this product not expressly approved by Uniden, or operation of this product in any way other than as detailed by this Operating Guide, could void your authority to operate this product. EARPHONE WARNING! Be sure to use only a monaural earphone or 32 stereo headset. Use of an incorrect earphone or stereo headset might be potentially hazardous to your hearing. The output of the phone jack is monaural, but you will hear it in both headphones of a stereo headset. Set the volume to a comfortable audio level coming from the speaker before plugging in the monaural earphone or a stereo headset of the proper impedance (32 ). Otherwise, you might experience some discomfort or possible hearing damage if the volume suddenly becomes too loud because of the volume control or squelch control setting. This might be particularly true of the type of earphone that is placed in the ear canal. WARNING! Uniden does not represent this unit to be waterproof. To reduce the risk of fire or electrical shock, do not expose this unit to rain or moisture. Astro®, DPL®, Digital Private Line®, Motorola®, PL®, PRIVACY PLUS®, Private Line®, SMARTNET®, and SMARTZONE® are registered trademarks of Motorola, Inc. 2 LTR® is a registered trademark of E.F. Johnson Co. EDACS® is a registered trademark of M/A-COM Private Radio Systems Inc. Uniden® and Bearcat® are registered trademarks of Uniden America Corporation. Trunk TrackerTM, Trunk TrackingTM, and Close CallTM are proprietary trademarks of Uniden America Corporation. Other trademarks used throughout this manual are the property of their respective holders. Power Related Issues Important: To prevent memory from being corrupted, do not unplug the AC adapter during the time the memory is accessed for programming or auto store. Notes: · If when you connect the AC adapter the [VOL] /Power Switch is ON, the scanner may not power on. Should this occur, simply turn the control OFF, then ON again. · If the scanner loses power (as when you turn off your car's ignition with the scanner's power switch on), it can lose some system settings such as display color and backlight. To ensure that such settings persist, either change the setting using the scanner's menu or power the scanner off then back on using the power switch after making such setting changes.When you turn off the scanner using the power switch, the scanner remembers the last settings and mode. When you turn power back on, it resumes the previous mode. Precautions 3 Table of Contents Precautions........................................................................................................................................ 2 Power Related Issues ................................................................................................................... 3 Table of Contents ............................................................................................................................. 4 The FCC Wants You To Know ......................................................................................................... 9 Scanning Legally ............................................................................................................................. 9 Introduction .................................................................................................................................... 11 Feature Highlights .......................................................................................................................... 12 General ....................................................................................................................................... 12 GPS ............................................................................................................................................. 15 Weather ....................................................................................................................................... 15 Search ......................................................................................................................................... 15 Auto Store 16 Priority ......................................................................................................................................... 16 PC Control and Cloning 16 Memory Storage Limits .................................................................................................................. 16 Search Lockout Limits ................................................................................................................... 17 About This Manual ......................................................................................................................... 17 Using the Scroll Control [FUNC] ................................................................................................. 17 How the Scanner's Controls Are Represented in This Manual ................................................... 18 Entering Text Within A Menu Option ........................................................................................... 18 A Short User's Guide to Assist the First-Time Scanner Enthusiast .......................................... 19 Understanding Scanning and the BCD996T ................................................................................ 21 Understanding the Scanner's Memory .......................................................................................... 21 Understanding Quick Keys ............................................................................................................ 21 What is Scanning? ......................................................................................................................... 22 What is Searching? ........................................................................................................................ 22 What is CTCSS/DCS? ................................................................................................................... 22 Conventional Scanning .................................................................................................................. 23 Simplex Operation ......................................................................................................................... 23 Repeater Operation ....................................................................................................................... 24 What is Trunk Tracking? ................................................................................................................ 24 Trunked Scanning .......................................................................................................................... 25 Types of Trunking Systems ........................................................................................................... 25 Motorola Trunking ....................................................................................................................... 25 EDACS Trunking ......................................................................................................................... 26 LTR Trunking .............................................................................................................................. 27 Startup Configuration ..................................................................................................................... 28 Setup/Operation .......................................................................................................................... 28 Multi-Site Trunking ......................................................................................................................... 28 I-Call (Motorola/EDACS) ................................................................................................................ 29 Where To Get More Information .................................................................................................... 29 Information On The Internet ........................................................................................................ 29 Included With Your Scanner ......................................................................................................... 30 Setting Up Your Scanner ............................................................................................................... 31 Base Station .................................................................................................................................. 31 4 Setting Up an Audio Recording Device or Computer Recording ................................................... 33 Vehicle Installation ......................................................................................................................... 33 Mounting Using the Bracket ........................................................................................................ 33 Mounting Using the DIN-E Sleeve .............................................................................................. 34 Removing the Scanner from the DIN-E Sleeve ........................................................................... 36 Mounting Using ISO Technique .................................................................................................. 36 Removing the Display Sticker ..................................................................................................... 37 Connecting an Optional Antenna ................................................................................................... 37 Connecting an Earphone/Headphone ........................................................................................... 37 Connecting an Extension Speaker ................................................................................................ 38 Controls, Keys, and Functions ..................................................................................................... 39 A Look At The Display ................................................................................................................... 44 Operation ........................................................................................................................................ 45 Turning On the Scanner and Setting the Squelch ......................................................................... 45 Startup Key Operation ................................................................................................................... 45 Conventional ............................................................................................................................... 45 Trunked ....................................................................................................................................... 45 Search Range ............................................................................................................................. 45 Scanning Systems ......................................................................................................................... 46 Preprogrammed System Tips ........................................................................................................ 47 Selecting Systems to Scan ............................................................................................................ 47 Selecting System Channel Groups ................................................................................................ 47 Locking/Unlocking Systems ........................................................................................................... 48 Locking/Unlocking Channels ......................................................................................................... 48 ID Scan/ID Search Mode ............................................................................................................... 48 Holding On a System ..................................................................................................................... 49 Holding On a Channel ................................................................................................................... 49 Quickly Storing an ID During ID Search ........................................................................................ 49 Quick-Storing Channels or Talk Group ID's (TGID) ...................................................................... 49 Trunking Activity Indicators ............................................................................................................ 50 Toggling the Display Mode ............................................................................................................ 51 Optimizing P25 Performance ........................................................................................................ 52 Conventional System .................................................................................................................. 52 Trunked System .......................................................................................................................... 52 Using the Menu .............................................................................................................................. 54 Programming General Settings .................................................................................................... 55 Setting and Using the Backlight ..................................................................................................... 55 Setting the Dimmer ..................................................................................................................... 55 Setting the Backlight Color .......................................................................................................... 56 Adjusting the Key Beep ................................................................................................................. 56 Setting the Audio AGC .................................................................................................................. 56 Setting the Display Orientation ...................................................................................................... 57 Adjusting the Display Contrast ...................................................................................................... 57 Setting the GPS Format ................................................................................................................ 57 Setting the Position Format ......................................................................................................... 57 Setting the Time Format .............................................................................................................. 58 Setting the Time Zone ................................................................................................................. 58 Setting the Distance Units ........................................................................................................... 58 Table of Contents 5 Setting the Serial Port Speed ........................................................................................................ 58 Displaying Scanner Information ..................................................................................................... 59 Viewing Memory Used ................................................................................................................ 59 Viewing the Firmware Version and Electronic Serial Number ..................................................... 59 Initializing the Scanner's Memory .................................................................................................. 59 Connecting Your Scanner to a Personal Computer ....................................................................... 60 Volume/Squelch with PC Control ................................................................................................ 60 Wired Cloning ................................................................................................................................ 60 Programming Your Scanner .......................................................................................................... 62 System Settings .......................................................................................................................... 63 System Options ........................................................................................................................... 63 Site Settings ................................................................................................................................ 65 Channel Settings ......................................................................................................................... 66 Programming Conventional Systems ............................................................................................ 66 Programming Trunked Radio Systems .......................................................................................... 67 Programming System Settings ...................................................................................................... 67 Editing the System Name ............................................................................................................ 67 Specifying the Correct System Type ........................................................................................... 68 Programming System Options .................................................................................................... 68 Programming Sites ........................................................................................................................ 76 Programming Channel Groups ...................................................................................................... 83 Setting Up a Channel Group ....................................................................................................... 83 Editing a Channel Group Name .................................................................................................. 83 Setting the Group Quick Key ....................................................................................................... 84 Editing Channels ......................................................................................................................... 84 Locking Out Channel Groups ...................................................................................................... 84 Deleting Channel Groups ............................................................................................................ 85 Programming Channels ................................................................................................................. 85 Creating a Channel ..................................................................................................................... 85 Editing the Channel Name (Alpha Tag) ...................................................................................... 85 Editing Frequencies .................................................................................................................... 86 Editing the Talk Group ID ............................................................................................................ 86 Setting the Audio Type ................................................................................................................ 87 Selecting CTCSS/DCS Tones ..................................................................................................... 87 Quick CTCSS/DCS Save ............................................................................................................ 88 Setting Channel Modulation Method ........................................................................................... 88 Setting Channel Attenuation ....................................................................................................... 89 Setting Channel Priority .............................................................................................................. 89 Setting Channel Alert .................................................................................................................. 90 Set Record ..................................................................................................................................... 90 Searching and Storing ................................................................................................................... 93 Service Search .............................................................................................................................. 93 Quick Search ................................................................................................................................. 94 Custom Search .............................................................................................................................. 94 Editing a Custom Search Range ................................................................................................... 95 Search With Scan .......................................................................................................................... 96 Set Delay Time .............................................................................................................................. 98 Set Attenuator ................................................................................................................................ 98 Set Record ..................................................................................................................................... 98 6 Assigning a Search Range to a Search Key ................................................................................. 98 Saving a Found Channel (Quick Save) ......................................................................................... 99 Auto Search and Store .................................................................................................................. 99 Selecting a System to use for Storing ......................................................................................... 99 Conventional Search and Store .................................................................................................. 99 Trunked Search and Store ........................................................................................................ 100 Using the Close Call Feature ...................................................................................................... 101 Setting Close Call Options ........................................................................................................... 101 Close Call Hits ............................................................................................................................. 103 Close Call Hits with Scan ............................................................................................................ 103 Search and Close Call Options ................................................................................................... 105 Managing Locked-Out Frequencies .......................................................................................... 105 Unlocking All Frequencies ......................................................................................................... 106 Reviewing Locked-Out Frequencies ......................................................................................... 106 Searching for Subaudible Tones ............................................................................................... 106 Screening Out Broadcast Sources ............................................................................................ 106 Finding Repeater Output Frequencies ...................................................................................... 107 Setting the Maximum Auto Store Value .................................................................................... 108 Setting the Modulation Type .................................................................................................... 108 Setting Attenuation .................................................................................................................... 109 Setting Data Skip ...................................................................................................................... 109 Setting the Delay Time .............................................................................................................. 110 Setting the Search Frequency Step .......................................................................................... 110 Setting Record .......................................................................................................................... 110 Adjust P25 Level ....................................................................................................................... 111 Priority Scan ................................................................................................................................ 111 Using Weather Alert (SAME) ....................................................................................................... 113 Searching For a Weather Broadcast ........................................................................................... 113 Turning Weather Alert On/Off ...................................................................................................... 114 Programming a SAME Group ...................................................................................................... 114 Setting WX Alert Priority .............................................................................................................. 115 Fire Tone-Out ................................................................................................................................ 116 Setting Tone-Out Standby ........................................................................................................... 116 Setting Up Tone-Out .................................................................................................................... 116 Tone-Out Multi-Channel Monitoring ............................................................................................ 118 Set Record ................................................................................................................................... 118 Using the BCD996T with a GPS .................................................................................................. 119 Device Compatibility .................................................................................................................... 119 Connecting Your Scanner to a GPS Device ................................................................................ 119 Initial Scanner/GPS Operation .................................................................................................... 119 Location-Based (GPS) Scanning ................................................................................................. 120 Another Example of Multiple Site Creation .................................................................................. 121 Non-Radio Location Based GPS Features .................................................................................. 121 Setting the Options ...................................................................................................................... 122 For POI Only ............................................................................................................................. 123 For Dangerous Xing, and Dangerous Road Only ........................................................................ 123 Deleting a Location ...................................................................................................................... 124 GPS Display Mode ...................................................................................................................... 125 Table of Contents 7 GPS Review Location Mode ........................................................................................................ 126 Care and Maintenance ................................................................................................................. 128 General Use ................................................................................................................................. 128 Location ....................................................................................................................................... 128 Cleaning ....................................................................................................................................... 128 Birdies .......................................................................................................................................... 128 Troubleshooting ........................................................................................................................... 129 Specifications ............................................................................................................................... 132 Reference ...................................................................................................................................... 135 Preset Fleet Maps ....................................................................................................................... 135 User Defined Fleet Maps ............................................................................................................. 137 Type I Programming Information .............................................................................................. 137 Size Code Restrictions ............................................................................................................. 138 Preprogrammed Systems and Lockout Options ....................................................................... 139 Preprogrammed Systems with Quick Keys ............................................................................... 140 CTCSS Frequencies .................................................................................................................... 141 DCS Codes .................................................................................................................................. 141 Index .............................................................................................................................................. 143 One-Year Limited Warranty ......................................................................................................... 150 8 The FCC Wants You To Know This scanner has been tested and found to comply with the limits for a scanning receiver, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This scanner generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this scanner does cause harmful interference to radio or television reception, which can be determined by turning the scanner on and off, you are encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna · Increase the separation between the scanner and the receiver This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Scanning Legally Your scanner covers frequencies used by many different groups, including police and fire departments, ambulance services, government agencies, private companies, amateur radio services, military operations, pager services, and wireline (telephone and telegraph) service providers. It is legal to listen to almost every transmission your scanner can receive. However, there are some transmissions that you should never intentionally listen to. These include: · Telephone conversations (cellular, cordless, or other private means of telephone signal transmission) · Pager transmissions · Any scrambled or encrypted transmissions According to the Electronic Communications Privacy Act (ECPA), you are subject to fines and possible imprisonment for intentionally listening to, using, or divulging the contents of such a conversation unless you have the consent of a party to the conversation (unless such activity is otherwise illegal). This scanner has been designed to prevent the reception of cellular telephone transmissions and the decoding of scrambled transmissions. This is done to comply with the legal requirement that scanners be manufactured so they are not easy to modify to pick The FCC Wants You To Know 9 up these transmissions. Do not open your scanner's case to make any modifications that could allow it to pick up transmissions that are illegal to monitor. Modifying or tampering with your scanner's internal components or using it in a way other than as described in this manual could invalidate your warranty and void your FCC authorization to operate it. In some areas, mobile and/or portable use of this scanner is unlawful or requires a permit. Check the laws in your area. It is also illegal in many areas (and a bad idea everywhere) to interfere with the duties of public safety officials by traveling to the scene of an incident without authorization. A license is required to use this product in Canada. 10 Introduction Your BCD996T scanner is a state-of-the-art scanner radio with Trunk Tracker IVTM and automatic scanning capabilities. You can store in the dynamic memory conventional frequencies such as police, fire/emergency, marine, air, amateur, and other communications. You can store and scan services that use Trunked Radio Systems and so much more. You can use the scanner's Scroll Control to quickly select channels and frequencies, and you can automatically program channels in a system using the Auto Store feature. Use your scanner to monitor: · Analog and digital trunked public safety systems (unencrypted only) · Police and fire departments (including rescue and paramedics) · NOAA weather transmissions · Business/Industrial radio and utilities · Marine and amateur (ham radio) bands · Air band · Railroad · Military and Civilian Aircraft Your scanner can monitor the following bands Lower Edge 25.0000 28.0000 29.7000 50.0000 54.0000 72.0000 76.0000 88.0000 108.0000 137.0000 144.0000 148.0000 150.8000 162.0000 174.0000 216.0000 225.0000 380.0000 764.0000 794.0000 Frequency (MHz) Upper Edge Modulation 27.9950 AM 29.6800 NFM 49.9900 NFM 53.9800 NFM 71.9500 WFM 75.9950 FM 87.9500 WFM 107.9000 FMB 136.9750 AM 143.9875 NFM 147.9950 NFM 150.7875 NFM 161.9950 NFM 173.9875 NFM 215.9500 WFM 224.9800 NFM 379.9750 AM 512.0000 NFM 775.9875 NFM 805.9875 NFM Step (kHz) 5.0 20.0 10.0 20.0 50.0 5.0 50.0 100.0 25.0 12.5 5.0 12.5 5.0 12.5 50.0 20.0 25.0 12.5 12.5 12.5 Introduction 11 Lower Edge 806.0000 849.0125 894.0125 1240.0000 Frequency (MHz) Upper Edge Modulation 823.9875 NFM 868.9875 NFM 956.0000 NFM 1300.0000 NFM Step (kHz) 12.5 12.5 12.5 25.0 Note: The scanner's frequency coverage is not continuous and does not include the cellular telephone or UHF TV bands. Feature Highlights General Close CallTM RF Capture Technology -- Instantly detects and tunes to nearby transmissions with no additional programming. See "Using the Close Call Feature" on Page 101 for more information. Close Call Do-Not-Disturb -- Checks for Close Call activity in between channel reception so active channels are not interrupted. Close Call Temporary Store -- Temporarily stores and scans the last 10 Close Call hits so that you can continue to monitor activity on those frequencies, even after you are out of Close Call detection range. Dynamically Allocated Channel Memory -- Your scanner's 6,000 channels are organized so that it more closely matches how radio systems actually work, making it easier to program and use your scanner and determine how much memory you have used and how much you have left. Preprogrammed Systems -- Your scanner is preprogrammed with over 500 agencies covering police, fire, and ambulance operations in the 25 most populated counties in the US, plus the most popular digital systems. A list of the scanner's preprogrammed systems is on Page 140. 100 Quick Keys -- You can set the scanner so you can quickly select systems and groups by using the keypad. This makes it easy to listen to or quickly lock out those systems or groups you don't want to scan. 13 Service Searches -- Frequencies are preset in separate Public Safety, News, HAM Radio, Marine, Railroad, Air, CB Radio, FRS/GMRS, Racing, TV Broadcast, FM Broadcast, Military, Air, and Special searches, to make it easy to search for specific transmissions. "Soft" Search Keys -- Lets you quickly search specified ranges. 12 Channel Lockout -- You can lock out any system, group, frequency, or channel while scanning. If you lock out a system or group, any channels belonging to that system or group are also locked out. Frequency Lockout -- You can lock out up to 500 frequencies (250 permanently locked out + 250 temporarily locked out). The scanner skips locked-out frequencies while using the Close CallTM feature or while searching. CTCSS and DCS Squelch Modes -- Prevent interference from stations not using the tone code you select. Analog and Digital Audio AGC -- Helps automatically balance the volume level between different radio systems. Fire Tone-Out Standby -- Lets you set the scanner to alert you if a two-tone sequential page is transmitted. You can set up to 10 settings (transmit frequency, tone frequencies) then select one for standby monitoring. Up to ten tone-outs on the same RF setting can be scanned at one time. Broadcast Screen -- Sets the scanner to ignore Close CallTM or search hits on known broadcast frequencies including common pager frequencies. Custom Screen -- Lets you input up to 10 frequency ranges that the scanner will ignore during Close CallTM or search operation. Scan/Search Delay -- The scanner pauses at the end of a transmission to wait for a reply. You can set the delay time for each system you scan, and while searching and using the Close CallTM feature. Attenuator -- Reduces the input strength of strong signals by about 20 dB. Repeater Reverse -- Automatically switches to the input frequency on a conventional repeater system. Channel Alert -- Alerts you when there is activity on any channel you specify using your choice of nine unique alert tones. Memory Check -- Lets you see at a glance how much total memory is left. Search with Scan Operation -- Lets you include selected service searches or custom search ranges during normal scan operation. Custom Alerts -- For each alert in the scanner (such as channel alert, Close Call alert, emergency alert), you can select from 9 different tone patterns and also set the alert volume level independently from the main volume level. Introduction 13 Automatic Channel Step -- Accepts frequencies on any valid channel step, even if it does not fall within the band plan's default step. Frequency Step -- Lets you select a frequency step (5, 6.25, 7.5, 8.33, 10, 12.5,15, 20, 25, 50 or 100 kHz) for manual mode and search mode. Text Tagging -- You can name each system, group, channel, talk group ID, custom search range, and SAME group, using up to 16 characters per name. Data Skip -- Allows your scanner to skip unwanted data transmissions and reduces the affect of birdies. Duplicate Frequency Alert -- Alerts you if you try to enter a duplicate name or frequency already stored in a system. Memory Backup -- If power is lost or disconnected, the scanner retains the frequencies you programmed in its memory. Temporary Lockout -- Makes it easy to temporarily lock out a system, channel, or frequency. The lockout is cleared when you turn power off, then back on so you don't have to remember to unlock the channels later. Startup Configuration -- Lets you easily manage multiple configurations for your scanner. Single-Handed Function Control Operation -- You can tap the Function/Scroll Control to enable the Function mode. It reverts to normal mode in about 3 seconds from your last press if no other action occurs. Record Out Jack -- Using the appropriate cable and audio recording device with signal control, you can record live audio of designated channels. Display and Keypad Backlight -- Makes the display and keypad easy to see in dim light using two color options and six light levels plus off. Vehicle Power Connection (Orange Wire) -- Lets you connect to your vehicle's dimmer circuit to also dim the scanner's display with the vehicle's dimmer control. Trunk Tracker IVTM Operation -- Follows unencrypted conversations on analog Motorola, Motorola Astro 25 (APCO 25), EDACS, EDACS SCAT, and LTR trunked radio systems, including systems in VHF, UHF, 700 MHz, 800 MHz, and 900 MHz bands. The scanner can scan both conventional and trunked systems at the same time. Multi-Site Trunking -- Lets you share system channels across multiple sites to more efficiently use the scanner's memory and more easily select sites to monitor. 14 Control Channel Only Scanning -- If the scanner is set to scan a Motorola system, you can set it so it scans using only control channel data. You do not have to program voice channel frequencies into memory in this mode as long as all possible control channels are programmed. Adaptive Digital Threshold -- Automatically sets the digital decode threshold for APCO 25 systems. GPS Location Based Scanning -- If you connect a GPS unit to the scanner it can automatically enable and disable systems based on the Location Information (longitude, latitude, Range) that you provide. GPS Non-Radio Based Features -- The scanner alerts you to Dangerous Intersections, Speed Alerts, and Points of Interest that you program into the scanner. GPS Display Mode -- Lets you display extended GPS information such as Distance to a POI, Direction to a POI, Time to a POI, Speed, Position, and more. Weather Weather Search -- Lets your scanner receive your local NOAA weather transmission. SAME Weather Alert -- Lets your scanner sound an alert when a SAME weather alert signal is transmitted on a NOAA weather channel. The scanner also displays the transmitted alert type. This helps you quickly find out about severe weather in your area and lets you avoid false alarms. WX Priority -- Lets your scanner alert you when a weather alert is transmitted on a NOAA weather channel. Search Service Search -- Lets you quickly select and search the scanner's preprogrammed frequencies. Custom Search -- Lets you program up to 10 custom search ranges. You can search any of these ranges simultaneously. CTCSS/DCS Search -- Lets the scanner search for CTCSS or DCS tones or codes on any channel or during a search. The scanner can identify up to 50 CTCSS tones and 104 DCS codes. Introduction 15 Quick Search -- Lets you search from the currently-tuned frequency if you are searching a conventional system. Auto Store Frequency AutoStore -- Automatically stores all active frequencies into the selected conventional system. Talk Group ID AutoStore -- Automatically stores all new talk group ID's into a channel group you select. Priority Priority Scan -- Priority channels let you keep track of activity on your most important conventional channel(s) while monitoring transmissions on other channels. Priority Plus -- You can set the scanner so it scans only the priority channels. PC Control and Cloning PC Control -- You can transfer programming data to and from your scanner and your personal computer, and control the scanner using a computer. This helps you find frequencies listed on the Internet and load them into the scanner. Free PC control and programming software will be available at http://www.uniden.com. Clone Mode -- You can clone all programmed data, including the contents of the scanner's memory, menu settings, and other parameters from one BCD996T scanner to another BCD996T scanner. Memory Storage Limits Systems 500 Sites 1000 Sites per Systems 256 Groups per System 20 Channels per Trunked Systems 250 Total Channels 6000 Trunked Frequencies per Site* 750-1000 Channels per Conventional Systems 1000 * depending on the number of TGID in the system. 16 Search Lockout Limits Frequencies 500 Temporary L/O Frequencies 250 Permanent L/O Frequencies 250 Skipped Search Mode Close Call Mode Review Menu Mode About This Manual The screen displays used in this manual are representations of what might appear when you use your scanner. Since what you see depends on the frequencies and user IDs for your area and the settings you select, you might notice some differences between what is in this manual and what appears on your scanner. To get the most from this manual, review the contents to become familiar with the basic functions available. If you are new to scanning or trunk tracking, start with the following short introduction to scanning and follow-up with the enclosed reprinted article on Programming provided with the courtesy of Popular Communications magazine. Using the Scroll Control [FUNC] The Scroll Control is a dual purpose control. It also lets you switch to secondary function operations. When used in this manner, you see F in this manual. Located prominently on the right of the BCD996T's front panel, the knob/switch lets you easily control channel selection, plus Normal and Function Modes, as well as how most of the information appears on the display. To adjust menu settings, change channels in Hold mode, and resume scanning: Simply turn the Scroll Control. To use F tap the Scroll Control. This action is written in shorthand as F which is fully explained in the next section. When you tap the control f appears and remains in the upper left corner of the display for 3 seconds. During this time, press any button to access the button's second function. Or, press and hold the Scroll Control for 2 seconds. The scanner beeps, and the function is "latched" so that is does not return to normal mode until you tap the Scroll Control again. f flashes at approximately 1 second intervals. If you select Function while scanning, the BCD996T continues to scan, but holds on the current system until the function operation is cancelled. Introduction 17 How the Scanner's Controls Are Represented in This Manual To help navigate the scanner's menus, the steps shown in this manual show the displays you see and the keys you press or control you operate to get a desired result. We use a form of shorthand symbols to save space. The following example shows you how to use the scanner's menu to edit an existing system name. It shows you the key to press in brackets [MENU] to select a menu option and the option you see on the LCD in Boldface Courier type (Program System) when you press [MENU]. It also instructs you to turn the Scroll Control (shown as ) to view a series of choices then press or tap the Scroll Control (the shorthand action shown as F to enter a choice such as Edit Name. [MENU] Program System F Select the system Edit Name F F Then, edit the system name. Entering Text Within A Menu Option To enter a letter, turn the Scroll Control ( ) until the letter, numeral or other character you want appears. To move the cursor to the left, press [4]. To move the cursor to the right, press [6]. To clear a character, press [.No] twice. To clear all characters, press [.No] three times. To accept an entry, press F or press [EYES]. To cancel an entry, press [MENU]. 18 A Short User's Guide to Assist the First-Time Scanner Enthusiast Welcome to the family of Uniden scanner users. You have just unpacked your Uniden BCD996T scanner. You are anxious to scan and hear something so you rotate the [VOL/POWER] control and wait a moment as the opening Message and Copyright screens confirm the model information. Then, if you live in a residential area, you probably hear nothing or very little. Why? The reason is simple. The programmable BCD996T does not instinctively know where you are and what you wish to listen to. Take a few minutes to assist in the `educating your scanner' process so you can enjoy listening for the first time and feel good about your purchase. Before proceeding, first follow the steps on Page 45 to set the volume and the squelch levels. Once set correctly, these settings let you listen at a comfortable level and let the scanner provide a signal whose strength is sufficient to be heard clearly. Always be sure to connect the provided antenna. There are several options that quickly assure you that your scanner works. The easiest is to activate the scanner's Weather System. Refer to Page 113 for the steps to tune to the nearest NOAA (National Oceanic and Atmospheric Administration) broadcast. Once you establish that the scanner operates using the NOAA information, and if you live in one of the areas listed on the Preprogrammed charts immediately following Page 140, you are ready to enter the exciting world of trunk tracking. Uniden has made it easy for you to start scanning. We have preprogrammed the BCD996T with more than 500 agencies across the U.S. If you live in one of the preprogrammed areas, simply press [SCAN/SEARCH] to start scanning. Then, press [.No] and the two-digit quick key for your area. One of the preprogrammed systems has common frequencies used across the country. By default, this system is enabled. To turn this system on or off, press [.No]. If you do not live in one of the preprogrammed system areas, refer to Page 140. There, you can follow the steps to select and search among the most popular service systems. Finally, you may decide to program the scanner yourself. To correctly program the BCD996T scanner begin on Page 62. The two programming steps are 1. Plan the system A Short User's Guide to Assist the First-Time Scanner Enthusiast 19 2. Program the system based on the plan. Enclosed with the materials provided with your scanner is a reprinted article from Popular Communications, which, in clear, easy-to-understand language, tells you how to start the programming session. The article also includes a glossary of terms and other valuable data. Be sure to take time out to look it over before proceeding. To provide you with useful sized worksheets and instructions to complete them, we have established links at our company website. Visit, http://www.uniden.com/scanners to see a list of helpful forms. But first, visit http://www.radioreference.com and locate the system nearest your location that you want to scan. If you register and pay a small fee, you can download a ready-to-use formatted PDF complete with the data from your selected system. Otherwise, you can print the blank worksheet on our web page as you would any other web based page. The programming data of a large metropolitan area may consist of many pages depending on how extensive the area's Public Service System Talkgroups are. Don't be overwhelmed. Begin by choosing the Talkgroups of interest to you. Begin by transferring the data from the Radio Reference website to the worksheets you obtain from the Uniden website and from there, to the scanner. You can visit one of the Radio Reference forums and potentially learn of someone in your immediate area who has programmed the same model scanner in your area. Then, by using the Clone feature or by exchanging files that you each have transferred to a computer using the Uniden Advanced Scanner Director (UASD) software you can install the programmed data into your scanner. Once you have either programmed or selected the option that lets you start experiencing scanning, spend the next few minutes learning the basics of trunk tracking for an even more complete listening appreciation. 20 Understanding Scanning and the BCD996T This section provides you with additional background on how scanning works and how your scanner provides that feature. You don't really need to know all of this to use your scanner, but some further background knowledge will help you get the most from your BCD996T. Understanding the Scanner's Memory Your scanner's memory is organized in an architecture called Dynamic Allocated Channel memory. This type of memory is organized differently and more efficiently than the bank/channel architecture used by traditional scanners. Dynamic Allocated design matches how radio systems actually work much more closely, making it easier to program and use your scanner and determine how much memory you have used and how much you have left. Instead of being organized into separate banks and channels, your scanner's memory is contained in a pool. You simply use as much memory as you need in the pool to store as many frequencies, and talk group ID's as desired. No memory space is wasted, and you can tell at a glance how much memory you have used and how much remains. With a traditional scanner, when you program it to track a trunked system, you must first program the frequencies. Since you can only program one trunking system per bank in a traditional scanner, if there were (for example) 30 frequencies, the remaining channels in the bank are not used and therefore wasted. Also, since some trunked systems might have hundreds of talk groups, you would have had to enter those types of systems into multiple banks in order to monitor and track all the ID's. Understanding Quick Keys Traditional "Banked" scanners let you select and deselect banks by pressing a single digit on the keypad. The BCD996T uses a similar method to turn on and off scanning sites and systems. When you program a system or site, you assign a quick key (System/Site Quick Key, or SQK) from 0 to 99. You can use the same quick key for multiple systems, so that the systems are turned on and off together. To turn a system/site on or off, just press the digit corresponding to the assigned SQK. For two-digit SQK's, first press [.No], then enter the two-digit SQK. The BCD996T lets you assign another quick key to a group of channels within a system. This group quick key (GQK) can be from 0-9. To turn on and off channel groups, you press F while the scanner is scanning the system containing the Understanding Scanning and the BCD996T 21 channels, then press the GQK within 2 seconds. Systems can have up to 20 channel groups, and multiple channel groups can be assigned to the same GQK. What is Scanning? Unlike standard AM or FM radio stations, most two-way communications do not transmit continuously. Your BCD996T scans programmed channels until it finds an active frequency, then stops on that frequency and remains on that channel as long as the transmission continues. When the transmission ends, the scanning cycle resumes until the scanner receives another transmission. What is Searching? The BCD996T can search each of its 13 service search ranges and up to 10 custom search ranges to find active frequencies. This is different from scanning because you are searching for frequencies that have not been programmed into the scanner's channels. You set the upper and the lower values of the range and then the scanner searches for any active frequency within the limits you specify. When the scanner finds an active frequency, it stops on that frequency as long as the transmission lasts. If you think the frequency is interesting, you can program it into the scanner's memory. If not, you can continue to search. What is CTCSS/DCS? Your scanner can monitor systems using a Continuous Tone Coded Squelch System (CTCSS) and Digital Coded Squelch (DCS) system, which allow squelch to open only when the tone you have programmed with a specific frequency is received along with a transmission. CTCSS and DCS are sub-audible tone signaling systems sometimes referred to as PL or DPL (Motorola's trademarked terms for Private Line and Digital Private Line respectively). CTCSS and DCS are used only for FM signals and are usually associated with both amateur and commercial two-way frequencies. These systems make use of a special sub-audible tone that accompanies a transmitted signal. CTCSS and DCS are used for many purposes. In many cases, CTCSS and DCS are used to restrict access to a commercial repeater, so that only those units which transmit the correct tone along with their signal can "talk" to the repeater. CTCSS and DCS are also used in areas that receive interference where there are several stations with output frequencies close to each other. When this occurs, you might hear multiple communications on the same frequency. The stations might 22 even interfere with each other to the point where it is impossible to clearly receive any of the stations. A scanner, such as your BCD996T, equipped with CTCSS and DCS, can code each received frequency with a specific sub-audible CTCSS or DCS frequency or code. Then, when you receive multiple signals, you only hear the transmission with the CTCSS or DCS tone you programmed. If you do not receive the correct tone with a signal, the scanner's squelch remains closed and you hear nothing. The tables showing the available CTCSS frequencies and DCS codes are found in the Reference Section of this manual. Conventional Scanning Conventional scanning is a relatively simple concept. Each group of users in a conventional system is assigned a single frequency (for simplex systems) or two frequencies (for repeater systems). Any time one of them transmits, their transmission always goes out on the same frequency. Up until the late 1980s, this was the primary way that radio systems operated. Even today, there are many 2-way radio users who operate using a conventional system: · Aircraft · Amateur radio · FRS/GMRS users · Broadcast AM/FM/TV stations · Many business radio users When you want to store a conventional system, all you need to know are the frequencies they operate on. When you are scanning a conventional system, the scanner stops very briefly on each channel to see if there is activity. If there isn't, the scanner quickly moves to the next channel. If there is, then the scanner pauses on the transmission until it is over. Simplex Operation Simplex systems use a single frequency for both transmit and receive. Most radios using this type of operation are limited to line-of-sight operation. This type of radio is frequently used at construction job sites, and with inexpensive consumer radios such as GMRS/FRS radios. The range is typically 1-15 miles, depending upon the terrain and many other factors. Understanding Scanning and the BCD996T 23 Repeater Operation Repeater systems use two frequencies: one transmits from the radio to a central repeater; the other transmits from the repeater to other radios in the system. With a repeater-based system, the repeater is located on top of a tall building or on a radio tower that provides great visibility to the area of operation. When a user transmits (on an input frequency), the signal is picked up by the repeater and retransmitted (on an output frequency). The user's radios always listen for activity on the output frequency and transmit on the input frequency. Since the repeater is located very high, there is a very large line of sight. Typical repeater systems provide coverage out to about a 25-mile radius from the repeater location. What is Trunk Tracking? Your BCD996T is designed to track the following types of trunking systems. · Motorola Astro 25 (APCO 25) trunking systems. · Motorola Type I, Type II, Type IIi hybrid, SMARTNET, and PRIVACYPLUS analog trunking systems, which are extensively used in 800 MHz communication systems. · LTR trunking systems · EDACS SCAT trunking systems · EDACS trunking systems When tracking these types of systems, you might want to remember that your scanner can track more than one trunking system at a time and scan conventional and trunked systems at the same time. Conventional scanning is a simple concept. You enter a frequency used by someone you want to monitor into your scanner's memory. For example, the police in your area might transmit on 460.500 MHz, the fire department on 154.445 MHz, the highway department on 37.900 MHz, etc. So when your scanner stops on a frequency, you usually know who it is, and more importantly, you can stop on a channel and listen to an entire conversation. This type of scanning is easy and fun. However, as the demand for public communications has increased, many public radio users do not have enough frequencies to meet their needs, creating a serious problem. Trunking radio systems help solve this problem. 24 Trunked Scanning While conventional scanning worked great while there were only a few groups wanting to use the frequencies, with the advent of smaller, lower-cost radios more and more agencies and businesses wanted to take advantage of the utility of 2-way radio. As a result, the bands that were used most became full, so new users were not able to take advantage of the technology as quickly as they wanted. Trunking solved this frequency shortage by allowing multiple groups to use the same set of frequencies in a very efficient way. While each type of trunking system operates a little differently (see the next few sections), they all work on the same basic premise: even in a system with a lot of users, only a few users are ever transmitting at any one time. Instead of being assigned a frequency, as with conventional systems, each group is assigned a talk group ID. A central computer controls the frequency each group operates on. This frequency selection is made each time a user transmits. So, while on a conventional system queries, replies, and follow-ups are all on a single frequency, they could each be on completely different frequencies on a trunked system. This semi-random frequency assignment made monitoring such a system impossible prior to Uniden's invention of the TrunkTracker scanner. Not only does your BCD996T scan channels like a conventional scanner, it actually follows the users of a trunked radio system. Once you know and program a talk group's ID (TGID), you won't miss any of the action. If you are a new scanner enthusiast, you might want to read the first part of this manual and use your scanner in conventional mode before you begin trunk tracking. Understanding scanning fundamentals and terminology will make trunk tracking much easier. If you are already an experienced scanner operator, you can review the programming worksheets and their associated pages on the Uniden website. Types of Trunking Systems Trunking systems divide a few frequencies among many different users, but the way that each system does this is slightly different. This section describes some of the technical data behind Motorola, EDACS, and LTR trunked radio systems. Motorola Trunking While there are different types of Motorola trunking systems, they all use the same basic trunking method. The system consists of one control channel (or as many as 4 per system but only one is active at any one time), plus one or more voice Understanding Scanning and the BCD996T 25 channels (typically 10, 20, or 28 total channels). When a user presses Push To Talk (PTT) to transmit, their radio first sends the person's talk group information to the control channel. The computer then assigns that talk group to a specific voice channel and transmits that data over the control channel. All radios in that talk group switch over to the assigned voice channel and the user can begin speaking. This all typically takes place in about a second. The person transmitting hears a beep from their radio when the channel is assigned. Then it is OK to start talking. The systems in use are: Motorola Type I -- the radios send the radio ID, the fleet and subfleet talk group ID to the control channel each time they transmit. To program a Type I system, you need to know the system's fleet map. The most common fleet maps are included in the Reference section in this manual. You can also find fleet map resources on the web such as at http://www.radioreference.com. Motorola Type II -- the radios only send the radio ID and radio channel code to the control channel. The central computer keeps a database of radio ID's and which talk group is assigned to which channel code for each radio, so with this system the user's radio sends only about 1/3 the data as a Type I system with each transmission. Type II systems do not use Fleet-subfleet talk groups; instead they use a 5-digit ID for each talk group. Type IIi Hybrid -- these systems support a mix of both Type I and Type II users. Like Type I systems, you must know the system's fleet map to ensure proper tracking. Motorola ASTRO 25 (APCO 25) -- these radios are similar to Type II systems, but send only the radio ID and radio channel code to the control channel, transmitting voice in digital form. EDACS Trunking EDACS trunking works in much the same way as Motorola trunking with a couple of major differences. In an EDACS system, each frequency used by the system is assigned a Logical Channel Number (LCN) so that less data needs to be transmitted by the control channel. Talk groups are assigned in an Agency-Fleet-Subfleet (AFS) hierarchy.There is one variation of EDACS called SCAT that your BCD996T can monitor. Logical Channel Numbers -- each frequency used by the system is assigned an LCN. This information is programmed into each user radio. When a user presses PTT, their radio sends their AFS information to the control channel. The computer then assigns that talk group to a channel and sends the LCN so that all other 26 radios in that talk group will switch to the correct channel. To program an EDACS system in your scanner, you will need to know both the frequencies used by the system and the LCN for each frequency. Agency-Fleet-Subfleet -- talk group ID's for EDACS systems are assigned in a way that makes it easy to see at a glance the affiliation of the user. Each radio is assigned a 2-digit agency identifier from 00 -- 15. For example, 01 might be used by the police, 02 by the ambulance service, 03 by the fire department, and so on. Each agency is then subdivided up to 16 times to provide fleet identification, and then 8 more times to identify subfleets. For example, the complete AFS for the Police Department West District's dispatch channel might be 01-062. 01 identifies the agency as the police department, 06 identifies the fleet as the West district, and 2 identifies the subfleet as the dispatch channel. While these assignments are somewhat arbitrary and vary from system to system, there are many resources on the web for finding the assignments for most systems. Because of the logical hierarchy of the AFS system, your BCD996T lets you assign wildcard ID's that let you, for example, use only one ID memory to identify all units in either an agency or a fleet. EDACS SCAT -- (Single Channel Autonomous Trunking) systems operate on a single channel and alternate control data with analog voice traffic. While your BCD996T cannot track ID's in this system, it can eliminate the control data so that all you hear is the voice transmissions when you monitor this type of system. LTR Trunking LTR (Logic Trunked Radio) systems are trunking systems used primarily by business or private communications service providers, such as taxicabs, delivery trucks, and repair services. These systems encode all control information as digital sub audible data that accompanies each transmission, so there is no separate control channel. Users on an LTR system are assigned to specific talk groups, which are identified by the radio as six digit numbers. These numbers are in the form AHHUUU, where: A = Area code (0 or 1) H = Home repeater (01 through 20) U = User ID (000 through 254) When the scanner receives a transmission on a channel set to the LTR mode, it first decodes the LTR data included with the transmission. In the ID search mode, the scanner stops on the transmission and displays the talk group ID on the display. In the ID scan mode, the scanner only stops on the transmission if the LTR Understanding Scanning and the BCD996T 27 data matches a talk group ID that you have stored in the talk group ID list and have not locked out. LTR systems are frequently programmed so that each radio has a unique user ID. Startup Configuration Setup/Operation The Startup Configuration option lets you quickly and automatically lock and unlock systems based on your desired configuration. Simply hold down a number button while powering on the scanner or while the opening screens are displayed. Systems assigned to that number are automatically unlocked and systems assigned to other numbers are automatically locked. Systems that are not assigned to any startup configuration are left unchanged. You could use this feature to give you quick, single-press Quick Key access to your favorite systems even when you travel to other locations. For example, if you program your scanner as follows: System/Site Quick Key 1 2 3 Configuration 1 Fort Worth Tarrant County Arlington Configuration 2 Phoenix Mesa Mariposa Cnty When you are in the Fort Worth area, press [1] while turning on the scanner. System Quick Keys [1], [2], and [3] then allow you to select between the local systems. When you travel to the Phoenix area, hold [2] while turning on the scanner. Now, the Fort Worth systems are locked out and System Quick Keys [1], [2], and [3] allow selection between the Phoenix-area systems. Multi-Site Trunking Some systems covering a very large geographic area use multiple antenna sites that each operate on different frequencies, but that use the same Talk Group ID's for traffic. When programming such a system, you program each site's frequencies and other settings into the system, then program the channels into channel groups within that system. Each site can have its own quick key, so you can turn each individual site on or off while you scan. Since all sites share all the channels within the system, multi-site trunking is much more efficient than programming each site as a separate system. 28 I-Call (Motorola/EDACS) I-calls are direct unit-to-unit transmissions that are not heard by other system users. Your BCD996T can receive I-call transmissions. See "Setting I-Call (Motorola and EDACS Systems Only)" on Page 72 for more information about monitoring I-call transmissions. Where To Get More Information By itself, this manual only provides part of what you need to know to have fun scanning -- how to program and use the scanner. Other sources provide additional information. Information On The Internet The Internet is the best source for current frequencies and information about scanning. Many web sites are dedicated to providing lists of frequencies for your area. Many have built-in database search engines to assist you. Make a list of the agencies you want to listen to, then look up the frequencies and systems used by those agencies. Here are a few useful sites: · http://www.scannermaster.com * -- frequency resources. You can also call them at 1 800 SCANNER (hours are from 10:00 a.m. to 5:00 p.m. Eastern Time Monday through Friday). · http://www.radioreference.com * -- the Internet's premier source for user-supported radio system information. · http://www.bearcat1.com -- frequency information from National Communications. · http://svartifoss2.fcc.gov/reports/index.cfm * -- conventional frequency information on file with the US Government · http://groups.yahoo.com/group/BCD996T * -- a group for people interested in discussing the BCD996T. * - These web sites are not affiliated with Uniden Corporation. For more information about Uniden and our products, visit http://www.uniden.com. Understanding Scanning and the BCD996T 29 Included With Your Scanner AC Adapter (P/N AD-1009) BCD996T Scanner Cigarette Lighter Adapter Power Cord Three Wire DC Power Cord -- See Step 5, "Mounting Using the DIN-E Sleeve" on Page 34 Mounting Bracket and Hardware DIN-E Sleeve and Removal Keys for vehicle installation Push-on type Telescopic Antenna Remote PC to Scanner Cable (scanner plug to Front PC Connecter) Owner's Manual and other printed material If any of these items are missing or damaged, immediately contact your place of purchase or Uniden Customer Service at: (800) 297-1023, 8:00 a.m. to 5:00 p.m., Central, Monday through Friday. 30 Setting Up Your Scanner These guidelines will help you install and set up your new scanner: The BCD996T can be placed on a convenient surface in your home as a base station, and connected to a standard outlet that supplies 120VAC, 60Hz. You must use either the supplied antenna or an electrically correct outdoor antenna, properly and safely mounted at your chosen site. The scanner is also designed to accommodate the DIN-E and ISO-DIN automotive mounting configurations. A DIN-E sleeve is supplied. The unit can also be placed above or beneath the dash of your vehicle using the supplied bracket and mounting hardware. · If your scanner receives interference or electrical noise, move the scanner or its antenna away from the source. · To improve the scanner's reception, use an optional external antenna designed for multi-band coverage. (You can purchase this type of antenna at a local electronics store). If the optional antenna has no cable, use 50-75 coaxial cable for lead-in. A mating plug might be necessary for the optional antennas. · Use an optional mono earphone or mono headset with proper impedance (32 ) for private listening. Read the precautions on the inside front cover of this Owners Manual. · Do not use the scanner in high-moisture environments such as the kitchen or bathroom. · Avoid placing the scanner in direct sunlight or near heating elements or vents. Base Station This is the simplest approach to let you get started quickly. Decide on a location that is convenient to a nearby wall outlet, has desk space to let you complete your programming worksheets, will safely allow the indoor antenna to be extended, or near a window to use an outdoor antenna. Setting Up Your Scanner 31 BCD996T Desk Surface Bracket Wood Screws Mounting Feet (4) To secure the radio, by means of the mounting bracket, to a surface, follow the steps below: 1. Attach the four protective rubber feet to the mounting bracket when you casually use the scanner on a flat surface. Should you desire to permanently mount the scanner, remove the feet and use wood screws through the bracket as described in Steps 2 and 3. 2. Use the bracket as a template to mark positions for the two mounting screws. 3. At the marked positions, drill holes slightly smaller than the screws. 4. Remove the paper backing from each washer and stick one inside of each bracket's ear, aligning the washer's hole with the bracket's hole. 5. Align the bracket with the threaded holes on the sides of the radio case so the bracket is beneath the radio. Secure the bracket using the two threaded knobs. Never overtighten the knobs. Once the radio is positioned, connect it to a source of AC power using the supplied 13.8V, 750 mA AC adapter. Insert the barrel of the AC adapter to the jack on the rear, upper right side of the radio marked . 32 WARNING! Use only the Uniden-supplied AC adapter with this scanner. Insert the connector of the supplied indoor telescoping antenna to the BNC Antenna Connector and apply moderate pressure to secure it. Setting Up an Audio Recording Device or Computer Recording It is best if you plan ahead when you initiate the basic setup of the scanner if you include the components to record incoming reception. You need only an audio recording device which can be controlled by a Voice Operated module (VOX) either externally or from within the unit and the correct connecting cable. The REC jack on the rear apron provides a constant-level audio output which is not affected by the setting of the volume control. Use a mono or stereo cable that ends in a 3.5mm plug for the scanner. The recorder might have its own requirements as to the proper plug. Check the recorder's instructions to be sure. Connect the cable to an external or internal VOX control so that the recorder activates when audio is present. You can also connect the cable to the appropriate input jack on your PC so that with controlling software, you can record to your hard disc. In order for the function to operate, you must set the channel to record. You must also set the system's record option to either All Channel, which will record all channels regardless of any channel's setting, or Marked Channel which only lets recording occur if you have selected record for that channel. Which you choose will depend on various factors. Vehicle Installation You can mount your scanner in your vehicle, using either the supplied bracket or the supplied DIN-E sleeve. Mounting Using the Bracket With the bracket removed from the radio, use the holes in the bracket as a template to initially mark the location you plan to use in your vehicle. Be absolutely certain of what might be behind the mounting surface before making any holes, be it above, or below, or in front of your dash, armrest console, or other location. If you Setting Up Your Scanner 33 drill carelessly, expensive damage can result. If in doubt, consult your vehicle dealer's service department or a qualified professional installer. Important: AVOID AIRBAG DEPLOYMENT ZONES. Ignoring this installation concern may result in bodily harm and the inability of the airbag to perform properly. Mounting Screws Star Washers 1. Using appropriate screws or other hardware, secure the bracket. 2. Insert the scanner and insert the bracket knobs to lock the scanner in position. 3. Attach the Cigarette Lighter Power Cord to the rear of the scanner and plug the adapter end into a dash mounted 12V DC socket. 4. Attach a suitable mounted mobile antenna to the antenna jack on the back of the scanner. Mounting Using the DIN-E Sleeve If you are unsure about how to install your scanner in your vehicle using the DIN-E sleeve, consult your automobile manufacturer, dealer, or a qualified installer. Before installing, confirm that your scanner fits in the desired mounting area and you have all the necessary materials to complete the task. Your scanner requires a 2 x 7-1/8 x 5-5/16 inch (50 x 180 x 135 mm) mounting area. Allow an additional 2-3/8 inch (60 mm) space behind the unit for connectors and wires. 34 Hole in dash DIN-E Sleeve BCD996T with outer case removed 1. Remove the bracket if previously attached. 2. Remove the four Philips screws on the rear that secure the outer metal case and pull off the case with care. 3. Install the DIN sleeve into the opening in your dashboard, lip facing out. 4. Push out the top and bottom tabs to hold the sleeve firmly in place. 5. Before inserting the scanner in the sleeve, attach the cable from the previously mounted antenna. Attach the DC Power leads. RED goes to a positive (+) connection on your fuse block while BLACK connects to the vehicle's chassis ground (-). 6. Connect the ORANGE lead to one side of the headlamp switch so that when you activate the headlights, the scanners LCD backlight dimmer level changes color and intensity. Be sure all the connections are routed away from any potentially pinching or slicing sheet metal. 7. Slowly slide the scanner into the sleeve until it locks in place. 8. To remove the unit, see "Removing the Scanner from the DIN-E Sleeve" on Page 36. Note: if you plan to connect a GPS unit or external speaker at a later time, expect to remove the unit for ease of making those connections. Setting Up Your Scanner 35 Removing the Scanner from the DIN-E Sleeve If you plan to connect other devices or wires to the radio, such as a GPS unit, at a later time, you should plan to remove the scanner from the DIN-E sleeve. This is easily done using the provided Removal Keys. Refer to the illustration that shows the removal key(s), on Page 30. Fully insert both Removal Keys into the slots on the left and the right edges of the radio's dress panel. You cannot remove the radio if only one key is available. Press in fully and the radio will unlock from the sleeve making withdrawal from the sleeve possible. Store the keys in a safe place for future use. Removal Keys Mounting Using ISO Technique Some vehicles can take advantage of another approach to mounting a radio in a vehicle, called the ISO technique. However, this technique requires a very detailed and thorough knowledge of the technique. Therefore, we strongly suggest that if you have any doubt about your experience and abilities, please consult with a professional installer who is familiar with the ISO approach to radio installation. To begin the process, it is first necessary to remove the scanner's outer metal sleeve from the inner chassis. Unthread the four screws in the rear of the unit. Slide the cover toward the rear and off. Once the sleeve is removed, you will see threaded, metric machine screw holes on either side of the chassis cabinet. Uniden does not supply these screws. Their diameter, length, and screw type should be chosen by a qualified installer based on the internal vehicle bracket which will be used in securing the scanner chassis. 36 Once the original radio is removed from the vehicle dash and the fit of the scanner is correct, be sure to connect all the power, audio, antenna, and any other cables or wires, to the scanner before the scanner is secured. The following illustration is a typical example of the ISO technique and the general side mounting screw holes often encountered. It does not actually represent your vehicle or your vehicle's mounting bracket. Only a professional installer will be able to determine the best and correct approach. Internal Bracket Dash Removing the Display Sticker Before you use the scanner for the first time, remove the protective plastic film over the display. Connecting an Optional Antenna The scanner's BNC connector makes it easy to connect a variety of optional antennas, including an external mobile antenna or outdoor base station antenna. Note: Always use 50- or 75-ohm, RG-58, or RG-8, BNC terminated coaxial cable to connect an outdoor antenna. If the antenna is over 50 feet from the scanner, use RG-8 low-loss dielectric coaxial cable. Cable loss increases with higher frequency. Connecting an Earphone/Headphone For private listening, you can plug a 1/8-inch (3.5 mm) mini-plug earphone or headphones (not supplied) into the headphone jack on the front of your scanner. This automatically disconnects the internal speaker. See "Earphone Warning" at the front of the manual for important information about using an earphone/headphone. Setting Up Your Scanner 37 WARNING! Never connect anything other than the recommended amplified extension speaker to the scanner's headphone jack. Damage to the scanner might occur. Connecting an Extension Speaker In a noisy area, an optional amplified extension speaker, positioned in the right place, might provide more comfortable listening. Plug the speaker cable's 1/8-inch (3.5-mm) mini-plug into your scanner's back-panel Ext. Sp. Jack. WARNING! Never connect any part of the headphone jack to the antenna jack or connect the radio to an installation where the antenna and audio connection are grounded. This might also damage the scanner. 38 Controls, Keys, and Functions 2 6 54 3 11 1 13 7 9 8 10 12 Antenna Connector Record Out External Spkr DC Adapter DC Vehicle Power In GPS/Remote The knobs and keys on the BCD996T produce several different actions. You can, for example, rotate the knobs as well as press them to achieve a different result. Pressing a key briefly can produce one result while pressing and holding, gives a different result. Many controls and keys behave differently depending on the mode your radio is in when you use them. Carefully examine the following table to separate those actions. Note: "Press" means press and release briefly. "Press and hold" means press and hold down for at least 2-seconds. F means Tap or Press the Scroll Control to put the scanner into Function mode then press the key under discussion. Controls, Keys, and Functions 39 Control/Key [Power/VOL] Label 1 All All Mode Action Rotate Press Result Power ON -- Volume Increase or decrease Backlight enabled and intensity changes: Green Low-Green Medium-Green High-Red Low-Red Medium-Red High Sets APCO threshold Function Press F then tap VOL Rotate Scroll Control Rotate Squelch 2 All Sets the Squelch Level to permit strong signals to be heard with no background noise or lower strength signals with some background noise Toggle: Close Call DND-CC Primary-OFF Turns on Close Call Only Mode Toggles to Tone-Out stand by mode Turn to change scanning or searching direction. Turn to select System or Search Range Press Press & Hold F Scroll Control and 3 Function F Scan or Custom Search Hold Menu All + Press Rotate Scroll Control + Rotate Rotate Rotate Press Turn to Select channel or frequency Turn to scroll to menu item-Tap to select current option Use as the key for menu choices Turn to select alpha/numeric entry for names Turn to resume scanning or searching Turn to operate alphabet skip Switches to Function Mode; To latch Function Mode, press and hold Func Toggle Priority Mode (On-Plus On-Off) Name Edit Monitor GPS Function [PRI] 4 Scan Rotate Rotate F+ Rotate Press/Tap Press 40 Control/Key [WX] Label 5 Mode WX Scan or WX Alert Scan Other Action Press Result Toggle between WX Scan and WX Alert Scan Turn to toggle WX Alert Priority On and Off Starts WX Scan Changes to GPS Mode Stores current GPS data Change GPS Display Temporarily locks out a system channel, a search frequency, or location data. Cancelled when Power is turned off. Permanently locks out system channel, a search frequency, or location data. Remains locked after power cycle. Exit the menu. Enables System Quick Key and Group Quick Key in the current system. Unlocks System, Group and Channel in the current system. Enables all System quick Keys and group Quick Keys and unlocks all systems, groups, channels, and search ranges. Unlocks all frequencies of Global Lockout List. Press Press & Hold [GPS] 6 All GPS Press Press & Hold [GPS] + F [L/O] 7 Scan Search Hold Press Press 2X Menu Scan/ Scan Hold Press Press & Hold F + Press & Hold Search Search Hold Close Call Only Close Call Hold Press & Hold Controls, Keys, and Functions 41 Control/Key [0] to [9] Label 8 Mode Scan Custom Search All Hold Close Call Tone-Out Scan Action Press Press Press Result Enable/Disable selected System/Site Quick Keys Turn on and off each custom search number Directly enter frequencies or Talk Group IDs Enable/Disable Group Quick Key [1] to [6] to start check of set search range [7/ATT] to toggle attenuator setting Switches to Display Mode- Mode 1 default Enables Trunking activity Indicators Moves the cursor left or right during name or label editing. Cancel error or warning messages Enter [.No] For frequency Enter "-" or "I" for TGID Delete current character in name edit Clear all letters in name edit Enter "-" or "I" for Direct Entry Toggle Active Channel Display On or Off Starts two-digit of (SQK) System/Site Quick Key F + Press Other than F + Press [1] Scan or GPS to [6] Other than F + Press [7] Scan or GPS All Scan/Scan Hold [4] move left [6] move right [.No] 9 Editing Name All Hold Close Call Only Tone-Out F + [0] F + [.No] Press Press Press Press Press 2X Press 3X Press Scan Scan Hold Scan F + Press Press 42 Control/Key [EYES] Label 10 Mode MENU Scan Scan Hold Search Search Hold Close Call Close Call Hold WX Scan WX Scan Hold Tone-Out Standby Action Press Press Press Result Use as the key for menu choices Edit the channel data for active channel Saves the active frequency Press Press Switches to Tone Out edit Menu to change Tone Out Settings Start Scanning Instant switch to Scan Mode [SCAN/SEARCH] 11 Scan Hold Press Other than Scan or Scan Hold or GPS Search Hold GPS Trunking Scan [HOLD/RESUME] 12 Scan Search Close Call Only WX Scan Scan Scan Hold GPS Menu All F + Press Press F + Press Press Toggle to resume searching Toggle to scanner LCD Toggle ID Search and ID Scan. Toggles HOLD on or off; In Close Call mode, error tone sounds if no frequency is detected. [MENU] 13 F + Press Initiates edit menu for current system, current search range, or current location data Back up one level in the menu. Use with Scroll Control to select menu settings Press Press Controls, Keys, and Functions 43 A Look At The Display The display has indicators that show the scanner's current operating status. The display information helps you understand how your scanner operates. The LCD screens shown here are only a few of many that you will see while in different modes. The ones we show here are more common and will assist you to get started. 1. 2. 3. 4. 5. 6. 7. Group Quick Key Site Quick Key Channel Group Name System Name Hold indicator Signal Strength indicator Close Call enabled 8. 9. 10. 11. 12. 13. 14. Talk group ID Number Talk group Frequency System Type (M, C, E, L) Modulation Type (Narrowband FM shown) Attenuation enabled Priority ON CTCSS or DCS Indicator 44 Operation Turning On the Scanner and Setting the Squelch To turn the scanner on, rotate [VOL] clockwise. Turn the knob to a comfortable sound level. Rotate the squelch control [SQ] clockwise until you either hear a broadcast or noise just stops. The control is now set for strong signals. If you desire to hear a weaker signal, turn it counter clockwise from that point until you hear background noise once more. Startup Key Operation You can setup a Startup Key Configuration so that the scanner can change the lockout for each system or each site by pressing an assigned key while you power up the scanner or an opening screen is displayed. Navigate to Set Startup Key there are differences in the menu structure for Trunked and Conventional systems. Conventional [MENU] Program System F Select the conventional system F Edit Sys Option F Set Startup Key Ffor each system. Trunked [MENU] Program System F Select the trunked system F Edit Site F Select the site F Set Startup Key F for each system or site. Search Range [MENU] Search for... Edit Service F Select a Service Range F Search with Scan F Set Startup Key F OR Operation 45 F Search for... [MENU] Edit Custom F Select a Custom Range F Search with Scan F Set Startup Key F F Assign all the systems/sites that you want to scan at the same time to the same startup key [0] to [9]. You can only assign a site/system to one startup key. To leave a system unassigned, press [.No]. Scanning Systems To begin scanning preprogrammed or programmed systems, press [SCAN/SEARCH]. The BCD996T scans all unlocked systems in all programmed and activated quick-key groups and any searches unlocked for search with scan. To enable or disable systems or sites for scanning, press the site/system's System/Site Quick Key while scanning. Notes: · If no systems are programmed, or all systems are locked out, Nothing to Scan appears. Program a system or select a system to scan. · When scanning multiple systems, the BCD996T scans systems according to the assigned quick key. Systems assigned to quick key 1 are scanned first, then 2, 3, 4, etc. Systems not assigned to a quick key are scanned last, then unlocked searches. Within a quick key, systems are scanned in the order they were assigned. · Within a system, channels are scanned according to the assigned channel group, with the same priority as described above for systems. · The BCD996T scans a system for the duration you set using the System Hold Time option (see "Setting the System Hold Time" on Page 70). For trunked systems, the scanner moves to the next system after the hold time expires, the current transmission ends, and the channel delay expires. Conventional systems operate similarly, but all unlocked channels are scanned at least one time regardless of the hold time setting. · Each search range is searched for the amount of time you set using the "Set Hold Time" option. See "Setting the System Hold Time" on Page 70 for more information. 46 Preprogrammed System Tips All systems preprogrammed into the scanner are assigned to a Quick Key. See "Preprogrammed Systems with Quick Keys" on Page 140 for a list of preprogrammed systems and their Quick Key assignments. Notes: · The systems preprogrammed into the scanner are located primarily in major metropolitan areas. · You might hear transmissions on frequencies assigned to very distant stations. This will happen if a local system also uses the same frequency. · The Nationwide system assigned to SQK 20 is enabled by default. Selecting Systems to Scan To select systems to scan, press Scan then press the quick key assigned to the system or systems you want to scan. For quick keys [0] - [9], press the quick key's number. For quick keys 10-99, press [.No] then press the quick key's 2-digit number. To stop scanning the system(s), press [.No] (if the quick key is a 2-digit quick key) then the number button or buttons again. The Sx: (system) indicators on the display show the systems that are currently selected. To select or lock out a system that is not assigned to a key, press Func then rotate the Scroll Control until the desired system is selected. Then, press [L/O] within 2 seconds to either lock out or unlock the system. Selecting System Channel Groups Within a system, you can assign groups of channels to a group quick key (see "Setting the Group Quick Key" on Page 84). Follow these steps to activate or deactivate a channel group within a system while scanning. 1. Tap F then turn the Scroll Control to switch to the Function Mode. Then to select the system that has the channel group ypu want to enable or disable. 2. While f still appears on the display, press the number key corresponding to the channel group you want to activate or deactivate. Operation 47 Locking/Unlocking Systems Follow these steps to lock out a system so that it does not scan even if its quick key is selected. 1. Tap F to switch to the Function Mode then rotate the control to select the desired system. 2. Press [L/O] to temporarily lock out the system. Temporary L/O appears. Or, quickly press [L/O] twice to permanently lockout the system. Locked Out appears. 3. To unlock temporarily locked out systems, turn power off and then back on. To unlock permanently locked out systems, repeat Steps 1 and 2. System Unlocked appears. Locking/Unlocking Channels If the scanner has stopped on a channel press [L/O] once to temporarily lock it out or quickly press [L/O] twice to permanently lock it out. Cycling power off/on automatically unlocks temporarily locked-out channels. To lockout a channel when the scanner has not stopped on the channel, or to unlock a permanently locked-out channel. 1. Press [HOLD/RESUME] to hold on a channel. 2. Tap F to switch to the Function Mode , then rotate the control system where the channel is stored. 3. Tap F or wait 2 seconds, then rotate the Scroll Control channel you want to lock or unlock. to select the to select the 4. Press [L/O] to temporarily lock or unlock the current the channel. Double-tap L/O to permanently lockout the current channel. ID Scan/ID Search Mode While you are scanning a trunked system, the scanner can be in either ID Scan or ID Search mode: · ID Scan -- the scanner only stops on talk group ID's (TGID) that you have programmed into the system that are unlocked. · ID Search -- the scanner stops on any unlocked talk group that becomes active. 48 To toggle between ID Scan and ID Search, press while the scanner is scanning the system. F then press [SCAN/SEARCH] If the scanner does not scan the system long enough for you to easily do this, press F and rotate the Scroll Control to select the changed system. Then, press [SCAN/SEARCH] within 2 seconds. Holding On a System To temporarily hold on a system, tap F. To hold on a different system, tap F then rotate the control to select the system. Normal scanning resumes 2 seconds after your last selection. To permanently hold on a site or system, press and hold the Scroll Control for 2 seconds. f flashes in the display's upper left corner. The scanner continues to scan only the current system. To hold on a different site or system, rotate the Scroll Control to select the new site or system then press [EYES]. Holding On a Channel To hold on a channel, press [HOLD/RESUME] while the channel is active. To select a different channel, turn the Scroll Control. If you scroll past the beginning or end of the current system, the scanner selects channels in the previous or next system. To resume scanning, press [SCAN/SEARCH]. Quickly Storing an ID During ID Search To quickly store an active talk group ID during ID search, press [EYES]. You see: Quick TGID Save? To save the ID into a channel, press [EYES]. Otherwise, press [.No]. If you press [EYES], the scanner stores the ID into a channel group called Qck Save Grp in the current system. Quick-Storing Channels or Talk Group ID's (TGID) 1. Hold on an existing channel in any system. 2. Enter the frequency or talk group ID you want to store (press twice to enter hyphens in talk group ID's). 3. To quick-store the channel or talk group ID, press [EYES]. Otherwise, press [.No]. Operation 49 If you enter a frequency then press [EYES], the scanner stores it in the Qck Save Grp group in a system called Qck Save Cnv Sys. These groups are created if they do not exist. Then, the scanner prompts you to save other channel settings. If you enter a talk group ID then press [EYES], the scanner stores it into a channel group named Qck Save Grp in the current system. If the talk group ID's format is not the type used by the current system, the scanner displays an error message and does not save the talk group ID. If you pressed [.No] in Step 3, the scanner prompts you to select the system and the group where you want to store the frequency or talk group ID. Note: The scanner will warn you if you try to store two channels in the same system that have the same frequency or Talk Group ID or if you try to store two systems with the same name. Trunking Activity Indicators To get a visual indication of the activity on trunking systems, press [HOLD/RESUME] to hold on any channel. Then tap F and then press [.No] The scanner replaces the third line on the display with trunking activity indicators. When the scanner is monitoring on EDACS or Motorola system, the activity indicators will show which system frequencies have activity. Note: For Motorola systems you must program all system frequencies (control and voice frequencies) for this feature to work. Trunking Activity Indicators. 50