Operating Instructions For 1 Introduction The CLIKR -5 UR5U-8700L-IP is designed to operate ADB, Amino, AT&T, Myrio, Motorola and Wegener IPTV set tops, plus the majority of TV, VCR, DVD and AUDIO equipment on the market as shown below. STB : Set top boxes TV : Televisions VCR : VCRs and TV/VCRs DVD: DVD Players AUX : Audio Receivers and DVRs, etc. TM 4 Button Functions SYSTEM ON/OFF Designed to send Power On/Off commands for up to five Components with one button press. Refer to section E for details. Cable Remote Control UR5U-8700L-IP CLIKR -5 TM POWER Allows you to turn your TV, VCR, DVD, AUX and Set top box On and Off. AUX, DVD, VCR, TV, STB Used to select the component you want to operate and signals remote control activity. MENU Displays the Applications Menu. INFO GUIDE Displays the program guide listings. Displays information about the program currently playing or highlighted in the program guide. STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote control toward the Component and enter the 3-digit code number assigned to your brand. *Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off. STEP4 After you've entered the correct code number and the Component has turned Off, press the [POWER] button to turn the Component back On. Now it is time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand until you find the best Component code. STEP5 Once you have found the correct 3-digit code, save it by pressing the same [COMPONENT] button one more time. The Component LED light will blink twice to confirm that the code was successfully stored. Now, program the rest of your Components by repeating STEPS 1-5. *Note : If the Pre-Programmed Method did not work, or if the Code Tables do not list your Component brand, use the AutoSearch Method as explained in Section B. STEP4 Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, repeat from STEP 3 using [CH ] or [CH ] buttons to find the correct code. STEP5 Save the code. (Same as for 3-Digit *Note : If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off. STEP4 Test functions. (Same as for 3-Digit STEP1 Press the [TV] button and the STEP1 Press the [STB] button to select the STB Code Programming Method - Section A). Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method. [OK/SEL] button simultaneously for 3 mode. seconds. The [TV] Component LED STEP2 Press the [MACRO] button and [OK/SEL] will turn on for 30 seconds. button simultaneously for 3 seconds. STEP2 Press the [VOL ] button. The [STB] button will turn on for 30 seconds. STEP3 Press the [TV] button again. The Component LED will blink twice to confirm the programming. To return to original state: If you wish to restore the STB channel control in TV mode, repeat the above steps but press [STB] in STEP3 . STEP3 Enter the the 2, 3 or 4-digit code for the 6 Set-up Code Tables CBL-IPTV Manufacturer/Brand ADB AMINO AT&T CISCO COMCAST DIGEO MYRIO MOTOROLA MOXI NOW TV PACE SCIENTIFIC ATLANTA WEGENER TV Manufacturer/Brand BELCOR BELL&HOWELL BENQ BOXLIGHT BRADFORD BROCKWOOD BROKSONIC BYDESIGN CANDLE CAPEHART CARY AUDIO DESIGN CELEBRITY CENTURION CETRONIC CHANGHONG CITIZEN CLARION CLASSIC CLP CLASSIC COLORTYME CONCERTO CONCIERGE CONTEC CORNEA CORONADO CRAIG CROSLEY CROWN CURTIS MATHES CXC CYBERHOME DAEWOO DAYTRON DELL DIGITAL PROJECTION DIMENSIA DREAMVISION DUKANE DUMONT DURABRAND DWIN DYNASTY DYNEX EIKI ELECTROBAND ELECTROGRAPH ELECTROHOME ELEKTRA ELEMENT EMERSON TV Set-Up Code Number Manufacturer/Brand HARVARD HAVERMY HELLO KITTY HIMITSU HISENSE HITACHI HP HUMAX HYUNDAI ILO INFINITY INFOCUS INITIAL INSIGNIA INTEQ JANEIL JBL JCB JCPENNEY JENSEN JVC KAWASHO KEC KENWOOD KLEGG KLOSS KMC KNOLL SYSTEMS KONKA KREISEN KTV KURAZAI LG LITEON LODGENET LOEWE LOGIK LUXMAN LXI MAGNAVOX Set-Up Code Number Set-Up Code Number 254 255 315 249 251 313 251 313 153 254 255 253 153 314 313 251 250 OK/SELECT Selects highlighted screen options. EXIT Exit from current screen. SETTINGS Displays settings menu. PAGE Accesses pages above or below the information currently displayed. 2 Replacing Batteries Before you program or operate the remote control, you must install two new AA alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover. MUTE Silences the audio. Press to activate. Press again to restore sound to the previous level. CURSOR NAVIGATION PAD Navigate to and highlight an item from the on-screen choices. C. Finding a Component Button's Setup Code Number If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference. STEP1 Press the [COMPONENT] button (TV, VCR, DVD or AUX) you want to verify and the [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds. STEP2 Press the [INFO] button and count the number of times the Component LED light blinks. This number indicates the first digit of the code, followed by the second and third, each separated by a one second pause when the LED will turn off. *Note : 10 blinks represents the number zero. Example : One blink, (pause), eight blinks, (pause) and three blinks, indicates code number 183. VOLUME Raises or lowers the sound level. A, B, C, D Make direct selections from on-screen menus. FAV Displays favorite channels. CHANNEL Selects the next higher or lower channel. ON DEMAND Provides direct access to On Demand channel. LAST Returns to the previously tuned channel. Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code. STEP5 Once you have found the correct 3digit code, save it by pressing the [AUX] button one more time. The Component LED light will blink twice to confirm the code was stored. Now when you press the AUX button, all the buttons will work with that 5th Component. G. Programming Volume Control channel you want programmed first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. Repeat this process for the third channel. The [STB] button will blink once for each channel entered. CBL-CABLE Converters Manufacturer/Brand SCIENTIFIC ATLANTA PIONEER PACE SAMSUNG MOTOROLA GENERAL INSTRUMENT HAMLIN HITACHI JERROLD MAGNAVOX MEMOREX MOXI PANASONIC PHILIPS PULSAR RCA REGAL REGENCY SKY SONY SPRUCER TOCOM TOSHIBA VIEWSTAR ZENITH Set-Up Code Number 001 003 041 042 045 046 001 103 034 051 063 076 105 001 005 002 001 030 002 111 148 005 103 104 049 050 055 103 055 005 004 103 005 003 008 009 010 069 010 012 052 111 252 044 047 006 012 013 020 085 052 047 049 050 057 230 108 047 039 040 056 052 012 015 052 060 093 100 BACK Takes you to the screen you visited previously. INTERACTIVE Displays the IPTV interactive. E. Programming the System On/Off Button This allows you to program the System On/Off button so it can send up to five power On/Off commands with one button press. STEP1 Press the [STB] button. STEP2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [STB] button will turn on for 30 seconds. STEP3 Press the first [COMPONENT] button you want to store in the [SYSTEM ON/OFF] button and then the [POWER] button. Repeat this for other Components until you have stored all the desired power commands into the [SYSTEM ON/OFF] button. STEP4 Press the [CH ] button to save the power commands you stored. The [STB] button will blink twice to confirm the commands have been saved. Volume and Mute control are factory- STEP4 Press the [CH ] button to store the channels that were selected. The [STB] programmed to automatically transfer to the button will blink twice to confirm the respective Component mode you select, as storage of commands. follows: To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will However, you can program the volume controls bring up the second channel. Press again and (Volume Up, Volume Down and Mute) from one it will bring up the third channel. Component to operate in another Component. STB : STB DVD: TV T V : TV AUX: AUX VCR: TV If you wish to store the TV volume control in I. Low Battery Warning STB mode, use the following steps. When the batteries are low and need to be STEP1 Press the [STB] button and the replaced with fresh batteries, the Component [OK/SEL] button simultaneously for 3 LED lights will blink 2 times in sequence seconds. The [STB] Component LED whenever a [POWER] button is pressed to turn will turn on for 30 seconds. on equipment. STEP2 Press the [VOL ] button. STEP3 Press the [TV] button. FWD M BUTTONS IPTV company custom-programmable Macros. Refer to Section H for programming steps. Forward ahead in stored or recorded programs. VCR/DVD/VOD KEYS Perform standard VCR and DVD functions when in VCR and DVD mode, and Video-On-Demand functions when in STB mode. Replays the previous few seconds of a program. NUMBER PAD Enter numbers to tune to channels. Also, make numeric entries on on-screen menus. NOTE: You can also use the CH or the program guide as alternate ways to tune to channels. RECORD TV Record a program on your TV ASPECT/# Reserved for future use. Changes the HD screen viewing aspect ratio through the IPTV STB. ON-OFF Opens or closes the PIP (Picture-In-Picture) window through the IPTV STB. PIP CH +/Selects the next higher or lower channel in the PIP (Picture-In-Picture) window through the IPTV STB. VIDEO SOURCE Selects the video source from available video Components through the IPTV STB. MOVE Moves the PIP (picture-In-Picture) window to another location on the screen through the IPTV STB. SWAP Swaps the contents of the PIP (Picture-In-Picture) window and the main viewing screen through the IPTV STB so that the PIP window displays on the main screen. LIGHT BUTTON Press to backlight all keypad buttons. Press again to turn off (or simply wait 10 seconds for automatic shut-off). J. Memory Lock System This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control. TV Manufacturer/Brand A MARK ABEX ACCURIAN ADMIRAL ADVENT ADVENTURA AIKO AKAI ALBATRON ALERON AMERICA ACTION AMPRO AMSTRAD ANAM AOC APEX DIGITAL AQUAVISION ASTAR AUDIOVOX AVENTURA AVION AXION 3 Operations DEFAULT STATE: Component Default: Set top box (STB) Channel Default: STB channel and numbers through the STB. You have the option of controlling your STB channel and numbers through the TV or VCR. Refer to section F for programming steps. Volume Default: Volume and Mute control are automatically transferred to the respective Component mode you select, as follows: STB: Set Top Box / TV: TV / AUX: AUX. Volume and Mute control for VCR and DVD are automatically transferred to the TV. However, you have the option of controlling STB Volume and Mute through the TV, VCR or AUX. Refer to section G for programming steps. 5 Programming the Remote Control There are two ways you can program your CLIKRTM-5 remote: * The Pre-Programmed 3-Digit Code Method * The Auto-Search Method The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-Search Method scans through all the codes in the remote control, one at a time. IMPORTANT SETUP NOTE! This pertains to all programming steps. When you are in setup mode, a component LED will light for 30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to start over. B. Auto-Search Method STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX). STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button simult ...