Detailed instructions for use are in the User's Guide.
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 1
MILLENNIUMTM 4
Universal Remote Control
User's Guide
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 2
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features And Functions . . . . . . . . . . . . . . . . . . . . . . 4
Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programming TV Control . . . . . . . . . . . . . . . . . . . . . 8 Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . 8 Programming VCR/DVD Player Control. . . . . . . . 12 Setup Codes for VCRs. . . . . . . . . . . . . . . . . . . . . . 13 Setup Codes for DVD Players. . . . . . . . . . . . . . . . . 15 Programming TV/VCR Combo Control . . . . . . . . 16 Setup Codes for TV/VCRs . . . . . . . . . . . . . . . . . . . 17
Programming Cable Converter (or DBS Receiver) Control . . . . . . . . . . . . . . . . . . . 18
To Unlock the CBL Key. . . . . . . . . . . . . . . . . . . . . . 18 To Program the CBL Key . . . . . . . . . . . . . . . . . . . . 19 To Lock the CBL Key . . . . . . . . . . . . . . . . . . . . . . . 20 Setup Codes for Cable Converters. . . . . . . . . . . . . 20 Setup Codes for DBS Receivers. . . . . . . . . . . . . . . 20 Programming Channel Control Lock . . . . . . . . . . 21 To Activate Channel Control Lock . . . . . . . . . . . . . 21 To De-Activate Channel Control Lock. . . . . . . . . . . 21 Programming Audio Control . . . . . . . . . . . . . . . . . 22 Setup Codes for Audio Amplifiers . . . . . . . . . . . . . 22 Setup Codes for Audio Receivers. . . . . . . . . . . . . . 23 Searching For Your Code . . . . . . . . . . . . . . . . . . . . 24 Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . 25 Programming The Power Key . . . . . . . . . . . . . . . . 26 Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . 27 Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . 28 To Change Volume Lock to the Cable Mode . . . . . . 28 To Change Volume Lock to the TV Mode. . . . . . . . . 28 To Change Volume Lock to the VCR Mode . . . . . . . 28 To Change Volume Lock to the Audio Mode . . . . . . 29 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Additional Information . . . . . . . . . . . . . . . . . . . . . . 31
2
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 3
INTRODUCTION
The Universal Electronics MillenniumTM 4 is our latest generation universal remote control. It is designed with sophisticated technology that will allow you to finally consolidate the clutter of all of the original remote controls in your home entertainment system. It's packed with easyto-use features such as: · Preprogrammed to operate the cable converter supplied by your cable system provider · Preprogrammed technology for easy setup · Preprogrammable Power key for master on/off control of all of your equipment with a single keystroke · Convenient hide-away sliding door to conceal less-used functions · Color-coded keys to quickly locate popular functions · Cable ID Lock to lock your remote control for use only with the cable converter · Channel Lock to lock channel selection only to the cable converter · Code library for video and audio components · Code Search to help program control of older or discontinued components Before you can use your new remote control, you will need to program it to operate the specific home entertainment components you wish to control. Follow the instructions detailed in this manual to set up your Millennium 4 and enjoy your new remote control.
3
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 4
FEATURES AND FUNCTIONS
Use the illustration below to locate Millennium 4 features and then study the Key Charts (on the next two pages) to learn how they function.
4
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 5
Key Charts
The LED (red light) blinks to show that the remote control is working and is sending signals. Press AUDIO, VCR, TV, or CBL once to select a home entertainment component to control. Press POWER once to turn on or off the selected home entertainment component. Use SETUP for all programming sequences. Use the keypad (0 ~ 9) to directly select channels (e.g., 09 or 31).
Press MUTE once to turn sound off or on. Press ENTER once after entering channel numbers on some TV models. Use VOL+ (or VOL-) to raise (or lower) the sound volume. Use CH+ (or CH-) to select the next higher (or lower) channel. Press LAST once to recall the last channel and to page back one screen in the main menu. Use FAV to cycle through your favorite channels that are stored in your cable converter. Use GUIDE to display the program guide. Use EXIT to exit out of your cable converter's menu and guide.
continued on next page...
5
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 6
FEATURES AND FUNCTIONS
Key Charts (continued)
Use cursor keys to move the cursor in the program guide and menu screens. Use SELECT/OK to choose options, PPV events, and to tune programs from the program guide. Use INFO to display current channel and program information. Press SETTINGS once to display your cable converter's screen menu. Use PAGE L (or PAGE M) to page up or down) through menu screens and the program guide. AÂBÂC "Cable Converter Features" (see converter manual. Slide the door open to reveal less-often used keys such as VCR transport buttons and cable converter features. In the VCR and TV modes, use the REW, PLAY, FF, REC, STOP, and PAUSE keys to control your VCR. To record a program, press REC twice. Reserved for cable converter features (see converter manual). Press TV/VCR once to switch the VCR to view TV channels or tape. This key will also control the input select feature on most TVs.
6
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 7
INSTALLING BATTERIES
1. 2. On the back of the Millennium 4, push the tab and lift off the battery cover. Obtain two (2) fully-charged AA alkaline batteries. Match the + and  marks on the batteries to the + and  marks in the battery case, then insert the new batteries. Press the battery cover back into place. The tab should click when the cover is locked. Test the unit by pressing POWER and any mode key (e.g. AUDIO, VCR, TV, or CBL). If the batteries are inserted correctly, the LED will blink once.
3. 4.
NOTE: Whenever batteries need replacement, the Millennium 4 will blink twice with every key press. Simply replace the batteries and the Millennium 4 will be restored to its full functionality, complete with your favorite settings.
7
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 8
PROGRAMMING TV CONTROL
NOTE: If you own a TV/VCR combination, skip this section and perform "Programming TV/VCR Combo Control" on page 16.
Locate the brand name of your TV in the Setup Codes for TVs in the next section, and write it in the space below. TV Brand: __________________________________ The brands are listed in alphabetical order with the most popular codes listed first.You will use one of these codes to program the Millennium 4 to operate your TV: 1. 2. Turn on the TV. On the Millennium 4, press TV once. Press and hold SETUP until the LED blinks twice, then release SETUP. Enter the first four-digit code for your TV. If you perform this procedure correctly, the LED will blink twice.
NOTE: If the LED did not blink twice after entering the code's last digit, then repeat steps 2 through 3 and try entering the same code again.
3.
4.
Aim the Millennium 4 at your TV and press POWER once. The TV should turn off. If it does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try searching for the code (see Searching For Your Code on page 24). Write your TV code in the boxes below for future reference.
5.
NOTE: Remember, to use the Millennium 4 to operate your TV, press TV first.
Setup Codes for TVs:
AOC Admiral Aiko Akai Alaron America Action Anam Audiovox Baysonic 0030, 0019 0093, 0463 0092 0030 0179 0180 0180 0451, 0180, 0623, 0092 0180
8
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 9
Belcor Bell & Howell Bradford Brockwood Broksonic CXC Candle Carnivale Carver Celebrity Cineral Citizen Concerto Contec Craig Crosley Crown Curtis Mathes Daewoo Daytron Denon Dumont Electroband Emerson Envision Fisher Fujitsu Funai Futuretech GE Gibralter GoldStar Gradiente Grunpy Hallmark Harley Davidson Harman/Kardon Harvard Hitachi Infinity Inteq JBL JCB JVC KEC KTV Kenwood Konka LG
0019 0154, 0016 0180 0019 0236, 0463 0180 0030, 0056 0030 0054 0000 0451, 0092 0060, 0030, 0056, 0092, 0280 0056 0180 0180 0054 0180 0047, 0747, 0054, 0154, 0051, 0451, 0093, 0060, 0030, 0056, 0145, 0016, 0166 0451, 0019, 0623, 0624, 0092 0019 0145 0017, 0019 0000 0154, 0236, 0463, 0180, 0178, 0179, 0019, 0623, 0624, 0282, 0280 0030 0154 0179, 0683 0180, 0179, 0171 0180 0047, 0747, 0051, 0451, 0093, 0178, 0021, 0282 0017, 0030, 0019 0030, 0178, 0056, 0019 0053, 0056 0180, 0179 0178 0179 0054 0180 0056, 0145, 0016 0054 0017 0054 0000 0053 0180 0180, 0030, 0280 0030, 0019 0707, 0628, 0632, 0638, 0703 0056 continued on next page...
9
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 10
PROGRAMMING TV CONTROL
Setup Codes for TVs (continued):
LXI Logik Luxman MGA MTC Magnavox Majestic Marantz Matsushita Megatron Memorex Midland Minutz Mitsubishi Motorola Multitech NAD NEC NTC Nikko Onwa Optimus Optonica Orion Panasonic Penney Philco Philips Pilot Pioneer Portland Prism Proscan Proton Pulsar Quasar RCA RadioShack Realistic Runco SSS Sampo Samsung Sansei Sansui Sanyo Scimitsu 0047, 0747, 0054, 0154, 0156, 0178 0016 0056 0150, 0030, 0178, 0019 0060, 0030, 0056, 0019 0054, 0030, 0179 0016 0054, 0030 0250 0178, 0145 0154, 0250, 0463, 0150, 0178, 0179, 0056, 0016 0047, 0747, 0017, 0051 0021 0093, 0150, 0178, 0019 0093 0180 0156, 0178, 0166 0030, 0056, 0019 0092 0030, 0178, 0092 0180 0154, 0250, 0166 0093, 0165 0236, 0463, 0179 0051, 0250 0047, 0747, 0156, 0051, 0060, 0030, 0178, 0021, 0056, 0019 0054, 0463, 0030, 0145, 0019 0054 0030, 0019 0166 0019, 0092 0051 0047, 0747 0178 0017, 0019 0051, 0250, 0165 0047, 0747, 0090, 0051, 0093, 0019, 0278 0047, 0747, 0154, 0180, 0030, 0178, 0056, 0019, 0165 0154, 0180, 0030, 0178, 0056, 0019, 0165 0017, 0030 0180, 0019 0030 0060, 0030, 0178, 0056, 0019 0451 0463 0154 0019
10
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 11
Scotch Scott Sears Semivox Semp Sharp Shogun Signature Sony Soundesign Squareview Starlite Supreme Sylvania Symphonic TMK TNCi Tandy Technics Technol Ace Techwood Teknika Telefunken Toshiba Vector Research Victor Vidikron Vidtech Wards White Westinghouse Yamaha Zenith
0178 0236, 0180, 0178, 0179, 0019 0047, 0747, 0054, 0154, 0156, 0178, 0179, 0056, 0171 0180 0156 0093, 0688, 0165 0019 0016 0000 0180, 0178, 0179 0171 0180 0000 0054, 0030 0180, 0171 0178, 0056 0017 0093 0051, 0250 0179 0051, 0056 0054, 0180, 0150, 0060, 0179, 0056, 0019, 0016, 0092 0056 0154, 0156, 0060 0030 0053 0054 0178, 0019 0054, 0030, 0178, 0021, 0179, 0056, 0019, 0016, 0165 0463, 0623, 0624 0030, 0019 0017, 0463, 0624, 0016, 0092
11
Millennium 4 Mnl M4094 rev
12/27/02
11:00 AM
Page 12
PROGRAMMING VCR/DVD PLAYER CONTROL
NOTE: If you own a TV/VCR combination, skip this section and perform "Programming TV/VCR Combo Control" on page 16.
Locate the brand name of your VCR in Setup Codes for VCRs on the next page, or your DVD player in Setup Codes for DVD Players on page 15, and write it in the appropriate space below. VCR Brand: ________________________________ or DVD Player Brand: ____________________________ The brands are listed in alphabetical order with the most popular codes listed first.You will use one of these codes to program the Millennium 4 to operate your VCR or DVD player: 1. 2. Turn on your VCR and insert a video cassette, or turn on your DVD player and insert a DVD. On the Millennium 4, press VCR once. Press and hold SETUP until the LED blinks twice, then release SETUP. Enter the first four-digit code for your VCR or DVD player. If you perform this procedure correctly, the LED will blink twice.
NOTE: If the LED did not blink twice after entering the code's last digit, then repeat steps 2 through 3 and try entering the same code again.
3.
4.
Aim the Millennium 4 at the VCR or DVD player and press POWER once. The device should turn off. If your VCR remote control does not have a POWER key, press PLAY. If the device does not respond, repeat steps 2-3, trying each code listed for your brand until you find one that works. If the device still does not work, try searching for the code (see Searching For Your Code on page 24). For future reference, write your device's code and type in the boxes and space below.
5.
Device Type:________________________
NOTE: Remember, to use the Millennium 4 to operate your VCR or DVD player, press VCR first.
12
Millennium ...
