Operating Manual For Easy Clicker UR3-SR2 Universal Remote Control, Inc. www.universalremote.com 1 Introduction This remote control is designed to operate most Digital and Analog Cable Boxes, as well as TVs, and a VCR or DVD player. 2 Replacing Batteries Before you program or operate the remote control, you must install two new AAA alkaline batteries. STEP1 Remove the battery compartment cover from the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover. Install two AAA alkaline batteries as shown here 1 3 Button Functions STEP1 Turn on the equipment that you want the remote control to operate Cable Box, TV and VCR(DVD). STEP2 Press the [DEVICE] button and the [SELECT] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. *Note : You can verify that you have selected the correct code by pressing the [MUTE] button. The equipment should turn on or off. STEP4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored. *Note : Try all the functions on the remote control. If any of the functions do not operate as they should, repeat the instructions from Step 2 using the next three-digit code number from the same brand list. 4 Programming the Remote Control. *Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the CBL, TV, or VCR button, depending on which device you are programming the remote to operate. B. Auto Search Method If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps: A. Manual Programming The remote control can be programmed by entering a threedigit code number that corresponds to particular brands and models of equipment. The three-digit code numbers are listed in the code tables sections of this instruction manual. 2 STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, or DVD). 3 STEP2 Press the [DEVICE] button and the [SELECT] button simultaneously for three seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on. STEP3 Press the [CH+] or [CH-] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the [CH+] or [CH-] button as soon as the equipment turns off. *Note : You can verify that you selected the correct code by pressing the [MUTE] button. The equipment should turn On or Off. D. Programming a Second TV to the VCR Button STEP1 Press the [VCR] button and the [SELECT] button simultaneously for 3 seconds. The VCR LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [TV] button. STEP3 Point the remote control toward the TV and enter the three-digit code for your TV from the TV codes table. STEP4 Store the three-digit code by pressing the [VCR] button. The device LED will blink twice to confirm that the code has been stored. STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored. E. Programming for Advanced Functions. In the CABLE device mode, the A,B,C and blank macro buttons can be programmed to act as macro buttons to send out up to 10 commands with one button press. In this section, when you're instructed to press a [MACRO] button, you need to press either the A, B, C or blank macro button (depending on which button you are attempting to program). *Note : The A, B, and C buttons are not programmable if you have a Digital Cable Box made by Pace, Pioneer, or Scientific-Atlanta. C. To find the Thr ee-Digit Code that W as Pr ogrammed using the Auto Sear ch Method STEP1 Press the appropriate [DEVICE] button and the [SELECT] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [INFO] button. The device LED will blink a number of times indicating the number of each digit for the code. Each digit is separated by a one second interval of the LED being off. Example : One blink, then three blinks, then eight blinks indicates the code number 138. *Note : Ten blinks indicates the number 0. STEP1 Press the [CBL] button to select the CABLE mode. STEP2 Press a [MACRO] button and the [SELECT] button simultaneously for 3 seconds. The CBL device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP3 Press up to 10 buttons you wish to store. The CBL device LED will blink once for each command entered. 4 5 STEP4 Press the [CH+] button to store the functions that are selected. The CBL device LED will blink twice to confirm the storage of functions. Example : If you wish to have the volume and mute keys operate your Cable Box, press the [CBL] button in Step3. To erase the Macro programming and return to the original function: STEP1 Press the [CBL] button to select the CABLE mode. STEP2 Press a [MACRO] button and the [SELECT] button simultaneously for 3 seconds. The CBL device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP3 Press the [CH+] button to erase the functions stored in the button. The CBL device LED will blink twice to confirm that the memory button has been erased. G. Assigning the Channel keys to a Different Device By default, the CH+, CH-, NUMERIC and LAST keys operate through your Cable Box. If you would like those keys to operate those functions on a different device, follow these steps. STEP1 Press the [SELECT] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [VOL -] button. The device LED will blink. F. Assigning the Volume and Mute keys to a Different Device By default, the VOL+, VOL- and MUTE keys operate through your TV. If you would like those keys to operate those functions on a different device, follow these steps. STEP3 Press the [TV] button. The device LED will blink twice to confirm the programming. *Note : If you wish to have the channel keys operate your Cable Box, press the [CBL] button instead of the [TV] button in Step 3. STEP1 Press the [SELECT] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on. H. Low Battery Warning When the battery is low (2.3V-2.0V) and needs to be replaced with fresh batteries, device LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on equipment. STEP2 Press the [VOL +] button. The device LED will blink. STEP3 Press the [DEVICE] button corresponding to the device that you would like the volume and mute buttons to control. The device LED will blink twice to confirm the programming. 6 I. Memory Lock System. This remote control is designed to retain programmed memory for 10 years -- even after batteries are removed from the remote control. 7 5 Set-up Code Tables CABLE TV MAKER(BRAND) NAME SCIENTIFIC ATLANTA TV MAKER(BRAND) NAME CODE No 001 011 021 022 023 008 002 005 006 012 024 025 002 048 042 043 044 005 046 047 037 038 039 040 004 030 031 001 013 028 029 045 003 035 036 032 033 034 AIWA AKAI AKIO ALARON AMARK AMERICA ACTION AMERICAN HIGH AMPRO ANAM AOC APEX DIGITAL AUDIOVOX AVION BAYSONIC BELL&HOWELL BRADFORD BROKSONIC CAIRN CANDLE CANON CAPEHART CARVER CELEBRITY CETRONIC CINERAL CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROSLEY CROWN CURTIS MATHES CXC DAEWOO DAYTRON DELL DENON DUMONT DWIN DYNASTY DYNATECH ELECTROBAND ELECTROHOME EMERSON CODE NUMBER (3 DIGIT) LIST 238 141 145 070 146 004 148 124 226 103 028 112 127 043 236 073 167 245 043 054 056 080 112 131 236 058 070 004 112 015 150 037 076 103 043 035 078 223 043 072 043 231 252 096 170 162 070 002 003 004 236 058 164 001 043 103 120 070 002 003 004 101 103 127 043 004 043 051 127 043 054 028 239 164 043 127 070 004 101 236 011 072 081 120 164 127 043 076 103 112 004 127 016 043 044 125 120 235 249 004 127 041 011 004 073 131 132 161 043 062 238 001 024 076 127 005 028 043 048 076 096 155 004 051 151 153 154 127 231 236 238 247 252 9 CONVERTER EXPLORER Series 8600X 8600 8540,8570,8590 8500 DCT Series (DVR Model) DCT Series,CFT2200 BMC9012/BMC9022 DSR470 CFT2000 DRZ DL4,DP(V),DQN(V),DPBB DRX Some Model CR6000 CR6600,6800,CR83 CRX5000 MOXI MEDIA CENTER IM781R IM781 SIGMAONE, P1,P2,P3, SIGMA 2000 RTC56,RKDM SIGMA 2001,2002 SIGMA 450,500,550 510 140,145,170,175 110,120,130,150,160 VOYAGER Series BA9000 BA4100,4200,4500 BA-V1000 ALL MODELS DHG-M55CV 5507 5503A MN2500 PM Z-TAC MOTOROLA GENERAL INSTRUMENT JERROLD HAMLIN MOXI NSC OAK PACE PANASONIC PIONEER REGENCY SONY TOCOM ZENITH TV MAKER(BRAND) NAME ADMIRAL ADVENT CODE NUMBER (3 DIGIT) LIST 072 081 160 161 096 147 8 TV MAKER(BRAND) NAME ENVISION ESA FISHER FUJITSU FUNAI FUTURETECH GATEWAY GE TV CODE NUMBER (3 DIGIT) LIST MAKER(BRAND) NAME MAGIN MAGNAVOX MAJESTIC MARANTZ MARTA MATSUI MATSUSHITA MAXENT MEGATRON MEI MEMOREX METZ MGA MIDLAND MINERVA MINTEK MINUTZ MITSUBISHI MOTOROLA MTC MULTITECH NAD NEC NIKEI NIKKO NTC OLEVIA ONKING ONWA OPTIMUS OPTOMA OPTONICA ORION PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND PRISM PROSCAN PROTON PROTRON CODE NUMBER (3 DIGIT) LIST 239 070 003 004 022 059 060 061 063 064 127 164 094 160 056 236 238 243 028 035 211 205 072 164 070 236 243 247 164 080 165 004 236 004 007 072 234 236 238 245 247 028 096 088 024 070 004 042 239 073 088 077 008 109 024 042 004 040 146 028 124 232 255 081 200 081 070 004 062 101 238 239 238 043 015 025 070 130 134 040 056 007 019 024 004 182 043 103 103 219 004 161 144 160 043 043 080 029 032 019 081 096 201 203 204 205 231 252 028 034 056 080 164 234 236 244 190 230 236 070 003 004 024 056 059 060 063 064 127 164 236 238 243 164 005 038 093 127 070 003 004 059 236 238 243 247 199 218 247 023 025 135 176 004 018 070 183 191 208 214 182 004 103 127 034 144 160 161 167 004 058 171 173 193 127 102 213 11 070 031 007 057 164 197 028 157 149 066 217 028 043 238 052 168 043 165 031 070 073 130 144 160 161 004 008 009 034 056 074 091 155 232 233 236 239 245 081 120 GEM 031 GIBRALTER 004 073 GO VIDEO 239 GOLDSTAR 004 106 112 127 247 250 GRUNPY 028 043 HALL MARK 004 HARLEY DAVIDSON 028 HARMAN KARDON 164 HARVARD 043 HISENSE 198 HITACHI 004 007 009 011 072 010 012 023 075 158 236 238 127 HP 027 039 098 HQ 238 HYUNDAI 049 067 INFINITY 164 INKEL 129 INSIGNIA 068 069 078 096 100 164 168 INSTANTREPLAY 236 INTEQ 073 JBL 164 JCB 001 JCL 236 JCPENNEY 004 008 024 030 065 070 101 160 156 234 236 239 247 127 JENSEN 013 JVC 038 001 034 083 195 236 242 159 227 KENWOOD 070 001 238 KLEGG 220 KLOSS 002 059 KTV 070 043 154 127 LG 004 106 112 127 247 250 LLOYD 238 LODGENET 072 LOEWE 196 164 LOGIK 072 LUXMAN 004 LXI 007 015 052 081 160 164 238 10 TV MAKER(BRAND) NAME QUASAR RADIO SHACK RCA REALISTIC RICO RUNCO SAMPO SAMSUNG SANSEI SANSUI SANYO SCEPTRE SCOTCH SCOTT SEARS SELECO SEMIVOX SEMP SHARP SIGNATURE SOLE SONY SOUNDESIGN SPECTRICON SQUAREVIEW SSS STARLITE SUPRE MACY SUPREME SVA SYLVANIA SYMPHONIC SYNTAX OLEVIA TANDY TATUNG TEAC TECHNICS TECHNOL ACE TECHWOOD TEKNIKA TELERENT TERA TV CODE NUMBER (3 DIGIT) LIST 034 056 234 236 244 004 019 127 043 250 160 161 144 156 065 070 004 023 024 056 074 152 232 233 236 238 239 081 007 019 236 238 239 247 241 072 073 130 179 180 181 182 216 194 070 004 058 165 004 101 127 133 160 089 105 070 237 239 184 185 192 120 238 252 096 007 053 057 082 020 239 036 004 004 005 028 043 048 127 004 007 015 028 030 057 082 094 160 238 247 052 164 127 189 043 015 081 014 019 028 004 022 236 251 127 072 238 177 178 001 085 126 139 236 240 241 003 004 028 043 238 112 052 004 043 043 002 001 046 070 003 059 060 063 064 127 160 164 044 056 236 238 243 168 052 238 168 219 004 161 144 160 081 238 056 062 238 034 080 236 244 028 004 002 003 004 024 028 043 072 101 103 236 238 247 164 127 072 172 12 MAKER(BRAND) NAME THOMPSON TNCI TMK TOSHIBA TOTEVISION UNITECH UNIVERSAL VIDEO CONCEPTS VIDEOSONIC VIDIKRON VIDTECH VIEWSONIC VIZIO WARDS WESTINGHOUSE YAMAHA YORK YUPITERU ZENITH ZONDA CODE NUMBER (3 DIGIT) LIST 166 073 004 015 030 007 040 062 101 142 045 ...