Operating Manual For Easy Clicker UR3-SR3 Universal Remote Control, Inc. www.universalremote.com 1 Introduction This remote control is designed to operate most Digital and Analog Cable Boxes, as well as TVs, and a VCR or DVD player. 2 Replacing Batteries Before you program or operate the remote control, you must install two new AAA alkaline batteries. STEP1 Remove the battery compartment cover from the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover. Install two AAA alkaline batteries as shown here 1 3 Button Functions 4 Programming the Remote Control. *Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the CBL, TV, or DVD button, depending on which device you are programming the remote to operate. A. Manual Programming The remote control can be programmed by entering a threedigit code number that corresponds to particular brands and models of equipment. The three-digit code numbers are listed in the code tables sections of this instruction manual. 2 STEP1 Turn on the equipment that you want the remote control to operate Cable Box, TV and DVD(VCR). STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. *Note : You can verify that you have selected the correct code by pressing the [MUTE] button. The equipment should turn on or off. STEP4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored. *Note : Try all the functions on the remote control. If any of the functions do not operate as they should, repeat the instructions from Step 2 using the next three-digit code number from the same brand list. B. Auto Search Method If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps: STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, or DVD). 3 STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on. STEP3 Press the [CH+] or [CH-] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the [CH+] or [CH-] button as soon as the equipment turns off. *Note : You can verify that you selected the correct code by pressing the [MUTE] button. The equipment should turn On or Off. STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored. C. To find the Thr ee-Digit Code that W as Pr ogrammed using the Auto Sear ch Method STEP1 Press the appropriate [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [INFO] button. The device LED will blink a number of times indicating the number of each digit for the code. Each digit is separated by a one second interval of the LED being off. Example : One blink, then three blinks, then eight blinks indicates the code number 138. *Note : Ten blinks indicates the number 0. D. Programming a Second TV to the DVD Button STEP1 Press the [DVD] button and the [OK/SEL] button 4 simultaneously for 3 seconds. The DVD LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [TV] button. STEP3 Point the remote control toward the TV and enter the three-digit code for your TV from the TV codes table. STEP4 Store the three-digit code by pressing the [DVD] button. The device LED will blink twice to confirm that the code has been stored. E. Programming for Advanced Functions. In the CABLE device mode, the A,B,C,D and blank macro buttons can be programmed to act as a 'Macro' or Favorite Channel button. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed with on button press. *Note : The A,B,C and D buttons are not programmable if you have a Digital Cable Box made by Pace, Pioneer or Scientific-Atlanta. STEP1 Press the [CBL] button to select the CBL mode. STEP2 Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds. STEP3 Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. Repeat this process for the third channel. The [CBL] button will blink once for each channel entered. STEP4 Press the [CH+] button to store the channels that were selected. The [CBL] button will blink twice to confirm the storage of commands. 5 To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third channel. To erase the Macro programming and return to the original function: STEP1 Press the [CBL] button to select the CABLE mode. STEP2 Press a [MACRO] button and the [OK/SEL] button simultaneously for 3 seconds. The CBL device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP3 Press the [CH+] button to erase the functions stored in the button. The CBL device LED will blink twice to confirm that the memory button has been erased. F. Assigning the Volume and Mute keys to a Different Device By default, the VOL+, VOL- and MUTE keys operate through your TV. If you would like those keys to operate those functions on a different device, follow these steps. STEP1 Press the [OK/SEL] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [VOL +] button. The device LED will blink. STEP3 Press the [DEVICE] button corresponding to the device that you would like the volume and mute buttons to control. The device LED will blink twice to confirm the programming. Example : If you wish to have the volume and mute keys operate your Cable Box, press the [CBL] button in Step3. 6 G. Assigning the Channel keys to a Different Device By default, the CH+, CH-, NUMERIC and LAST keys operate through your Cable Box. If you would like those keys to operate those functions on a different device, follow these steps. STEP1 Press the [OK/SEL] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [VOL -] button. The device LED will blink. STEP3 Press the [TV] button. The device LED will blink twice to confirm the programming. *Note : If you wish to have the channel keys operate your Cable Box, press the [CBL] button instead of the [TV] button in Step 3. H. Assigning the VCR/DV D VOD keys to control your VCR or DVD By default, the REW, Play, FF, Record, Stop and Pause keys operate VOD (Video On Demand) through your Cable Box. If you would like those keys to operate those functions on your DVD or VCR, press the PLAY button for 3 seconds until the DVD/VCR button lights. To return to your Cable Box control, press the PLAY key again for 3 seconds until the CBL button lights. I. Low Battery Warning When the battery is low (2.3V-2.0V) and needs to be replaced with fresh batteries, device LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on equipment. J. Memory Lock System. This remote control is designed to retain programmed memory for 10 years -- even after batteries are removed from the remote control. 7 5 Set-up Code Tables CABLE TV MAKER(BRAND) NAME SCIENTIFIC ATLANTA CONVERTER EXPLORER Series 8600X 8600 8540,8570,8590 8500 IPN Series DCT Series (DVR Model) VIP Series DCT Series,DCH Series, CFT2200 BMC9012/BMC9022 DSR470 CFT2000 DRZ DL4,DP(V),DQN(V),DPBB DRX Some Model ADB Series ADB5810WX AmiNET Series U-VERSE RNG200 IPN Series RNG200 2056-MSX HR20, HR21 CR6000 CR6600,6800,CR83 CRX5000 MOXI MEDIA CENTER MOXI HD DVR 2056-MSX Evo Series NOWTV IM781R IM781 SIGMAONE, P1,P2,P3, SIGMA 2000 RTC56,RKDM SIGMA 2001,2002 SIGMA 450,500,550 500 Series TDC Series DTA Series 140,145,170,175 110,120,130,150,160 VOYAGER Series BA9000 BA4100,4200,4500 BA-V1000 ALL MODELS SKY+HD DHG-M55CV 5507 5503A SMD 515 MN2500 PM Z-TAC CODE No 001 011 021 022 023 051 002 053 008 006 005 012 024 025 002 048 054 055 115 049 051 113 051 113 153 229 042 043 044 006 052 153 054 055 114 046 047 037 038 039 040 001 002 113 030 031 001 013 028 029 045 230 003 035 036 050 032 033 034 MOTOROLA GENERAL INSTRUMENT JERROLD ADB AMINO AT&T CISCO COMCAST DIGEO DIRECTV HAMLIN MOXI MYRIO NOW TV NSC OAK PACE PANASONIC PIONEER REGENCY SKY SONY TOCOM WEGENER ZENITH 8 TV MAKER(BRAND) NAME ADMIRAL ADVENT AIWA AKAI AKIO ALARON AMARK AMERICA ACTION AMPRO ANAM AOC APEX DIGITAL AQUAVISION AUDIOVOX AVION BAYSONIC BELL&HOWELL BRADFORD BROKSONIC CAIRN CANDLE CAPEHART CARVER CELEBRITY CETRONIC CINERAL CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROSLEY CROWN CURTIS MATHES CXC DAEWOO DAYTRON DELL DENON DIGITAL PROJECTION DUMONT DWIN CODE NUMBER (3 DIGIT) LIST 072 081 160 161 096 147 141 145 070 146 004 148 124 226 104 108 103 028 112 127 043 073 167 043 054 056 080 112 131 058 070 004 112 015 150 037 097 100 076 103 043 035 078 224 223 043 072 043 096 170 162 070 002 003 004 058 164 001 043 103 120 070 002 003 004 101 103 127 043 004 043 051 127 043 054 028 164 043 127 070 004 101 011 072 081 120 164 127 043 076 103 112 004 127 016 043 044 125 120 004 127 041 011 090 004 073 131 132 161 9 TV MAKER(BRAND) NAME DYNASTY DYNATECH FISHER ELECTROBAND ELECTROHOME ELEMENT EMERSON CODE NUMBER (3 DIGIT) LIST 043 062 007 057 001 024 076 127 004 110 005 028 043 048 076 096 155 004 051 151 153 154 127 121 ENVISION 070 EPSON 087 ESA 031 FUJITSU 164 197 028 157 149 066 217 FUNAI 028 043 052 168 FUTURETECH 043 GATEWAY 165 031 GE 070 073 130 144 160 161 004 008 009 034 056 074 091 155 081 120 GEM 031 GIBRALTER 004 073 GOLDSTAR 004 106 112 127 GRUNPY 028 043 HAIER 004 116 HALL MARK 004 HANNSPREE 099 HARLEY DAVIDSON 028 HARMAN KARDON 164 HARVARD 043 HISENSE 198 021 HITACHI 004 007 009 011 072 010 012 023 075 158 127 HP 027 039 098 HUMAX 122 HYUNDAI 049 067 ILO 055 INFINITY 164 INFOCUS 046 215 225 INKEL 129 INSIGNIA 068 069 078 096 164 168 INTEQ 073 JBL 164 JCB 001 JCPENNEY 004 008 024 030 065 070 101 160 156 127 JENSEN 013 JVC 038 001 034 083 195 159 227 10 TV MAKER(BRAND) NAME KENWOOD KLEGG KLOSS KREISEN KTV LG LODGENET LOEWE LOGIK LUXMAN LXI MAGNAVOX MAJESTIC MARANTZ MATSUI MATSUSHITA MAXENT MEGATRON MEMOREX METZ MGA MIDLAND MINERVA MINTEK MINUTZ MITSUBISHI MOTOROLA MTC MULTITECH NAD NEC NIKEI NIKKO NIKO NORCENT NTC NUVISION OLEVIA ONKING ONWA OPTIMUS OPTOMA CODE NUMBER (3 DIGIT) LIST 070 001 220 002 059 202 070 043 154 127 004 106 112 127 086 072 196 164 072 004 007 015 052 081 160 164 070 003 004 022 059 060 061 063 064 127 164 094 160 056 028 035 211 205 218 050 138 072 164 070 164 080 165 004 004 007 072 028 096 088 024 070 004 042 073 088 077 008 109 024 042 004 040 146 028 124 081 200 081 070 004 062 101 043 015 025 070 130 134 040 056 007 019 024 004 182 140 043 103 175 211 103 084 219 004 161 144 160 043 043 080 029 032 11 TV MAKER(BRAND) NAME OPTONICA ORION PANASONIC PHILCO PHILIPS PIONEER POLAROID PORTLAND PRISM PROSCAN PROTON PROTRON PROVIEW PROX QUASAR RADIO SHACK RCA REALISTIC REVOLUTION HD RUNCO SAMPO SAMSUNG SANSEI SANSUI SANYO SCEPTRE SCOTCH SCOTT SEARS SELECO SEMIVOX SEMP SHARP SHERWOOD SIGNATURE SOLE SONY SOUNDESIGN SOYO SPECTRICON SPECTRONIQ SQUAREVIEW CODE NUMBER (3 DIGIT) LIST 019 081 096 201 203 204 205 028 034 056 080 164 190 230 248 070 003 004 024 056 059 060 063 064 127 164 164 005 038 093 127 070 003 004 059 199 218 161 023 025 135 176 004 018 070 183 191 208 214 182 026 118 119 006 004 103 127 034 144 160 161 167 004 058 171 173 193 127 163 102 213 004 115 110 092 034 056 004 019 127 043 160 161 144 156 065 070 004 023 024 056 074 152 081 007 019 220 072 073 130 179 180 181 182 216 194 070 00 ...