Operating Instructions For 4-Function Cable Remote Control UR4U-MDVR2 1 Introduction This remote control is designed to operate all Motorola and Scientific Atlanta digital set top boxes (including HD and DVR), plus the majority of TVs, VCRs, DVDs and AUDIO equipment on the market as shown below. CABLE : Cable Converters TV : Televisions DVD : DVDs, TV/DVDs, VCRs and TV/VCRs AUX : Audio Receivers and DVRs, etc. 4 Button Functions STEP2 Press the [COMPONENT] button (TV, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED will light for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote control toward the Component and enter the 3-digit code number assigned to your brand. *Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off. STEP4 After you've entered the correct code number and the Component has turned Off, press the [POWER] button to turn the Component back On. Now it's time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand. STEP5 Once you have found the correct 3digit code, save it by pressing the same [COMPONENT] button one more time. The Component LED light will blink twice to confirm that the code was successfully stored. Now, program the rest of your Components by repeating STEPS 1-5. *Note : If the Pre-Programmed Method did not work, or if the Code Tables do not list your Component brand, use the Auto-Search Method as explained in Section B. STEP4 Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, repeat from STEP 3 using [CH ] or [CH ] buttons to find the correct code. STEP5 Save the code. (Same as for 3-Digit Code STEP4 Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code. STEP5 Once you have found the correct 3-digit To return to original state: If you wish to restore the CABLE channel control in TV mode, repeat the above steps but press [CBL] in STEP3 . Programming Method - Section A). Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method. code, save it by pressing the [AUX] button one more time. The Component LED light will blink twice to confirm the code was stored. Now when you press the AUX button, all the buttons will work with that 4th Component. G. Programming Volume Control You can program the volume controls (Volume Up, Volume Down and Mute) from one Component to operate in another Component mode. Default volume control settings on the remote control are as follows: CBL : TV DVD : TV T V : TV AUX : AUX 2 Replacing Batteries Before you program or operate this remote control, you must first install two new AA Alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover. C. Finding a Component Button's Setup Code Number If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference. STEP1 Press the [COMPONENT] button (TV, DVD or AUX) you want to verify and the [OK/SEL] button simultaneously for 3 seconds. The Component LED will light for 30 seconds. STEP2 Press the [INFO] button and count the number of times the Component LED light blinks. This number indicates the first digit of the code, followed by the second and third, each separated by a one second pause when the LED will turn off. *Note : 10 blinks represents the number zero. Example : One blink, (pause), eight blinks, (pause) and three blinks, indicates code number 183. E. Programming the System On/Off Button This allows you to program the System On/Off button so it can send up to four power On/Off commands with one button press. STEP1 Press the [CBL] button. STEP2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] Component LED will light for 30 seconds. STEP3 Press the first [COMPONENT] button you want to store in the [SYSTEM ON/OFF] button and then the [POWER] button. Repeat this for other Components until you have stored all the desired power commands into the [SYSTEM ON/OFF] button. STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the commands have been saved. If you wish to operate the CBL volume control in CBL mode, use the following steps. STEP1 Press the [CBL] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] Component LED will light for 30 seconds. STEP2 Press the [VOL +] button. STEP3 Press the [CBL] button. The Component LED will blink twice to confirm the programming. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps but press [TV] in STEP3 . H. Programming a Favorite Channel See on-screen Guide Menu. D. AUX Function: Programming a 4 th Component You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component. STEP1 Turn on the 4th Component you want to program (TV, VCR, DVD or Audio). STEP2 Press the [AUX] button and the [OK/SEL] button simultaneously for 3 seconds.The [AUX] Component LED will light for 30 seconds. STEP3 Press the [COMPONENT] button you want to setup. Point the remote control toward the Component and enter the 3-digit code number assigned to your brand. *Note : If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off I. Low Battery Warning When the batteries are low and need to be replaced with fresh batteries, the Component LED lights will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment. F. Programming Channel Control You can program the channel controls (Channel Up, Channel Down, Last and Numbers) from one Component to operate in another Component mode. Default channel control settings on the remote control are as follows: CBL : CBL DVD : DVD T V : CBL AUX : AUX 5 Programming the Remote Control 3 Operations DEFAULT STATUS: Component Default: CABLE Channel Default: CABLE channel +/- and numbers operate through the CABLE box. You have the option of controlling channel +/and numbers through the TV, VCR or DVD. Refer to section F for programming steps. Volume Default: CABLE volume +/- and mute operate through the TV. You have the option of controlling volume through the Cable box, VCR or DVD. Refer to section G for programming steps. There are two ways you can program your remote control: rogrammed * The Pre-Programm 3-Digit Code Method * The Auto-Search Method The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-Search Method scans through all the codes in the remote control, one at a time. IMPORTANT SETUP NOTES: This pertains to all programming steps. When you are in setup mode in each component, a component LED will light up for 30 seconds. If you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to start over. When programming a combo unit, program as a VCR or DVD first. B. Auto-Search Method STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX). STEP2 Press the [COMPONENT] button (TV, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED will light for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote toward the Component and press the [CH ] or [CH ] button one step at a time or keep it pressed. The remote will emit a series of ON/OFF commands. Release the [CH ] or [CH ] button as soon as the Component turns Off. J. Memory Lock System This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control. Universal Remote Control, Inc. www.universalremote.com OCE-0053B REV 01 (07/09/07) A. Pre-Programmed 3-Digit Code Method STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) . If you wish to operate the TV channel control in TV mode, use the following steps. STEP1 Press the [TV] button and the [OK/SEL] button simultaneously for 3 seconds. The [TV] Component LED will light for 30 seconds. STEP2 Press the [VOL -] button. STEP3 Press the [TV] button again. The Component LED will blink twice to confirm the programming. K. Record Your Component Set-up Codes TV DVD AUX Set-up Code Number: Set-up Code Number: Set-up Code Number: 6 Set-up Code Tables CABLE Converter Remote UR4U-MDVR2 TV Manufacturer/Brand GATEWAY GE GEM GIBRALTER GOLDSTAR GRUNPY HALL MARK HARLEY DAVIDSON HARVARD HAVERMY HELLO KITTY HIMITSU HISENSE HITACHI HP ILO INFINITY INFOCUS INSIGNIA INTEQ JANEIL JBL JCB JCPENNEY JENSEN JVC KAWASHO KEC KENWOOD KLEGG KLOSS KLOSS NOVABEAM KMC KONKA KTV KURAZAI LG LODGENET LOEWE LOGIK LUXMAN LXI MAGNAVOX MAJESTIC MARANTZ MATSUI MATSUSHITA MAXENT MEGATRON MEMOREX METZ MGA MIDLAND MINERVA MINTEK MINUTZ MITSUBISHI MONTGOMERY WARD MOTOROLA MTC MULTITECH NAD NEC NET TV NIKEI NIKKO NTC NUVISION OLEVIA ONKING ONWA OPTIMUS OPTONICA OPTOMA ORION PANASONIC PHILCO PHILIPS PILOT PIONEER POLAROID TV Set-Up Code Number 242 268 160 144 165 073 197 008 009 034 056 074 130 155 161 363 391 116 073 113 116 102 106 112 119 127 143 363 028 043 363 028 043 081 076 043 419 442 011 166 009 010 012 023 075 143 158 072 363 378 316 327 421 472 164 333 230 330 350 400 052 402 403 454 457 073 002 164 070 024 197 008 009 030 065 101 143 160 363 013 038 034 070 083 145 199 210 240 406 116 070 197 043 197 070 466 002 059 002 143 457 043 197 143 154 072 363 113 116 102 106 112 119 127 143 284 072 164 072 363 166 007 015 052 160 164 251 164 059 197 003 060 061 063 064 127 022 160 094 226 390 363 467 161 072 197 164 164 080 242 116 197 011 007 072 363 088 197 024 028 042 363 161 073 088 362 008 124 109 024 028 040 042 146 191 363 161 072 081 197 062 101 363 043 015 025 272 130 134 197 040 016 024 056 019 236 237 262 242 043 116 197 103 351 432 363 161 144 160 043 043 025 019 251 265 270 096 080 034 056 092 164 208 197 003 059 060 064 164 024 056 063 363 164 005 093 038 197 003 059 127 206 431 363 116 234 135 025 197 018 023 116 374 393 272 388 323 328 353 354 355 356 494 387 391 DVD Set-Up Code Number 143 363 034 144 160 161 165 167 131 058 143 171 173 193 363 392 398 116 073 034 056 092 019 143 043 127 363 333 160 165 065 144 161 197 024 056 152 023 074 363 007 019 043 047 186 168 169 178 179 180 181 182 073 395 416 197 058 242 363 258 050 089 101 105 127 143 160 228 229 363 197 076 096 166 007 020 053 057 082 187 276 116 197 028 043 048 143 363 015 030 007 028 057 143 094 160 082 165 166 363 189 200 205 011 251 019 014 028 029 022 143 175 363 081 116 088 072 003 231 232 001 139 147 126 185 085 213 277 028 003 043 363 112 052 043 043 363 116 002 070 328 197 003 052 059 060 063 064 164 044 160 127 052 432 363 161 144 160 251 056 062 034 080 028 363 002 003 24 028 043 072 101 143 363 037 046 072 172 363 073 138 015 030 007 040 062 101 325 143 096 008 009 145 146 174 188 192 164 363 242 389 002 472 363 386 387 008 009 019 028 060 061 063 064 072 074 143 164 034 363 015 076 280 435 147 001 197 371 372 363 363 043 363 073 072 095 103 284 112 DVD-DVD Recorder Set-Up Code Number 098 087 111 115 111 130 091 260 271 080 173 138 091 017 091 143 074 147 143 027 091 137 091 220 221 222 111 084 140 101 087 268 111 142 180 280 084 012 151 279 135 104 264 265 148 091 057 074 066 096 083 095 267 153 027 206 111 282 017 102 134 088 103 111 076 141 180 023 266 130 021 042 138 144 150 285 066 083 095 105 166 276 141 066 023 099 131 304 233 141 066 086 027 027 091 269 056 070 165 137 159 275 154 147 130 222 094 033 091 001 033 118 145 191 286 143 143 102 023 270 042 088 023 027 034 130 141 164 188 035 149 027 206 042 089 166 197 138 057 074 091 DVD-VCR Set-Up Code Number Manufacturer/Brand ELECTROHOME ELECTROPHONIC EMERSON FISHER FUJI FUNAI GARRARD GE GO VIDEO GOLDSTAR GRADIENTE HARLEY DAVIDSON HARMAN KARDON HARWOOD HITACHI HQ INSTANTREPLAY JCL JCPENNEY JENSEN JVC KEC KENWOOD KLH KODAK LG LLOYD LOGIK LXI MAGIN MAGNAVOX MARANTZ MARTA MAT ...