Operating Instructions For 1 Introduction The CLIKR -5 UR5U-8820 is designed to operate the Motorola, Scientific-Atlanta, Pioneer, Pace Micro and Samsung digital set tops, plus the majority of TV, VCR, DVD and AUDIO equipment on the market as shown below. CABLE : Cable Converters TV : Televisions VCR : VCRs and TV/VCRs DVD: DVD Players AUX : Audio Receivers and DVRs, etc. TM 4 Button Functions Cable Remote Control UR5U-8820L CLIKR -5 TM STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote control toward the Component and enter the 3-digit code number assigned to your brand. *Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off. STEP4 After you've entered the correct code number and the Component has turned Off, press the [POWER] button to turn the Component back On. Now it's time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand. STEP5 Once you have found the correct 3-digit code, save it by pressing the same [COMPONENT] button one more time. The Component LED light will blink twice to confirm that the code was successfully stored. Now, program the rest of your Components by repeating STEPS 1-5. *Note : If the Pre-Programmed Method did not work, or if the Code Tables do not list your Component brand, use the AutoSearch Method as explained in Section B. STEP5 Save the code. (Same as for 3-Digit Code Programming Method - Section A). Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method. E. Programming the System On/Off Button This allows you to program the System On/Off button so it can send up to five power On/Off commands with one button press. STEP1 Press the [CBL] button. STEP2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds. STEP3 Press the first [COMPONENT] button you want to store in the [SYSTEM ON/OFF] button and then the [POWER] button. Repeat this for other Components until you have stored all the desired power commands into the [SYSTEM ON/OFF] button. STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the commands have been saved. STEP2 Press the [VOL +] button. STEP3 Press the [TV] button. The Component LED will blink twice to confirm the programming. To return to original state: If you wish to restore the CBL volume control in CBL mode, repeat the above steps but press [CBL] in STEP3 . C. Finding a Component Button's Setup Code Number If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference. STEP1 Press the [COMPONENT] button (TV, VCR, DVD or AUX) you want to verify and the [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds. STEP2 Press the [INFO] button and count the number of times the Component LED light blinks. This number indicates the first digit of the code, followed by the second and third, each separated by a one second pause when the LED will turn off. *Note : 10 blinks represents the number zero. Example : One blink, (pause), eight blinks, ( pause) and three blinks, indicates code number 183. H. Programming a `Macro' button In CABLE mode, the M button can be programmed to act as a `Macro' . This allows you to program from one up to three separate channels that can be accessed by simply pressing the programmed Macro button. STEP1 Press the [CBL] button to select the CBL mode. STEP2 Press the [M] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds. STEP3 Enter the 3 or 4-digit code for the channel you want programmed first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. Repeat this process for the third channel. The [CBL] button will blink once for each channel entered. STEP4 Press the [CH+] button to store the channels that were selected. The [CBL] button will blink twice to confirm the storage of commands. To access the programmed channels, press the [M] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third channel. 2 Replacing Batteries Before you program or operate the remote control, you must install two new AA alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover. F. Programming Channel Control You can program the channel controls (Channel Up, Channel Down, Last and Numbers) from one Component to operate in another Component mode. Default channel control settings on the remote control are as follows: CBL : CBL DVD : DVD T V : CBL AUX : AUX VCR : CBL D. AUX Function: Programming a 5 Component th If you wish to store the TV channel control in TV mode, use the following steps. STEP1 Press the [TV] button and the [OK/SEL] button simultaneously for 3 seconds. The [TV] Component LED will turn on for 30 seconds. STEP2 Press the [VOL -] button. STEP3 Press the [TV] button again. The Component LED will blink twice to confirm the programming. To return to original state: If you wish to restore the CABLE channel control in TV mode, repeat the above steps but press [CBL] in STEP3 . You can take advantage of the AUX function to program a 5th Component such as a second TV, VCR, DVD or Audio Component. STEP1 Turn on the 5 th Component you want to program (TV, VCR, DVD or Audio). STEP2 Press the [AUX] button and the [OK/SEL] button simultaneously for 3 seconds.The [AUX] Component LED will turn on for 30 seconds. STEP3 Press the [COMPONENT] button you want to setup. Point the remote control toward the Component and enter the 3-digit code number assigned to your brand. *Note : If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off STEP4 Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code. STEP5 Once you have found the correct 3-digit code, save it by pressing the [AUX] button one more time. The Component LED light will blink twice to confirm the code was stored. Now when you press the AUX button, all the buttons will work with that 5th Component. B. Auto-Search Method STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX). I. Low Battery Warning When the batteries are low and need to be replaced with fresh batteries, the Component LED lights will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment. 5 Programming the Remote Control 3 Operations DEFAULT STATE: Component Default: CABLE Channel Default: CABLE channel and numbers through the CABLE. You have the option of controlling your CABLE channel and numbers through the TV or VCR. Refer to section F for programming steps. Volume Default: CABLE volume and mute through the CABLE. You have the option of controlling your CABLE volume and mute through the TV, VCR or DVD. Refer to section G for programming steps. There are two ways you can program your CLIKRTM-5 remote: * The Pre-Programmed 3-Digit Code Method * The Auto-Search Method The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-Search Method scans through all the codes in the remote control, one at a time. IMPORTANT SETUP NOTE! This pertains to all programming steps. When you are in setup mode, a component LED will light for 30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to start over. STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote toward the Component and press the [CH ] or [CH ] button one step at a time or keep it pressed. The remote will emit a series of ON/OFF commands. Release the [CH ] or [CH ] button as soon as the Component turns Off. STEP4 Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, repeat from STEP 3 using [CH ] or [CH ] buttons to find the correct code. G. Programming Volume Control You can program the volume controls (Volume Up, Volume Down and Mute) from one Component to operate in another Component mode. Default volume control settings on the remote control are as follows: CBL : CBL DVD : TV T V : TV AUX : AUX VCR : TV J. Memory Lock System This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control. If you wish to store the TV volume control in CBL mode, use the following steps. STEP1 Press the [CBL] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] Component LED will turn on for 30 seconds. K. Record Your Component Set-up Codes TV VCR DVD AUX Set-up Code Number: Set-up Code Number: Set-up Code Number: Set-up Code Number: Universal Remote Control, Inc. www.universalremote.com OCE-0052D REV 02 (04/30/07) A. Pre-Programmed 3-Digit Code Method STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX). 6 Set-up Code Tables CABLE Converter Remote Motorola UR5U-8820L Scientific-Atlanta, Pioneer, Pace Micro, Samsung 001 TV Manufacturer/Brand GE TV Set-Up Code Number Manufacturer/Brand PORTLAND PRISM PROSCAN PROTON PROTRON PULSAR QUASAR RADIO SHACK RCA REALISTIC ROCTEC RUNCO SAMPO SAMSUNG SAMSUX SANSEI SANSUI SANYO SCEPTRE SCOTCH SCOTT SEARS SELECO SHARP SHENG CHIA SHOGUN SIEMENS SIGNATURE SIMPSON SOLE SONY SOUNDESIGN SPECTRICON SQUAREVIEW STARLITE SSS SUPRA SUPRE MACY SUPREME SVA SYLVANIA SYMPHONIC SYNTAX OLEVIA TANDY TATUNG TECHNICS TECHNOL ACE TECHWOOD TEKNIKA TELEFUNKEN TELERENT TERA TMK TNCI TOSHIBA TOTEVISION TVS UNIVERSAL VICTOR VIDEO CONCEPTS VIDIKRON VIDTECH VIEWSONIC VIKING VIZIO WARDS WAYCON WESTINGHOUSE YAMAHA YORK YUPITERU ZENITH ZONDA VCR Set-Up Code Number 143 363 034 144 160 161 165 167 131 058 143 171 173 193 363 392 398 116 073 034 056 092 019 143 043 127 363 333 160 165 065 144 161 197 024 056 152 023 074 363 007 019 043 047 186 168 169 178 179 180 181 182 073 395 416 197 058 242 363 258 050 089 101 105 127 143 160 228 229 363 197 076 096 166 007 020 053 057 082 187 276 116 197 028 043 048 143 363 015 030 007 028 057 143 094 160 082 165 166 363 189 200 205 011 251 019 014 028 029 022 143 175 363 081 116 088 072 003 231 232 001 139 147 126 185 085 213 277 028 003 043 363 112 052 043 043 363 116 002 070 328 197 003 052 059 060 063 064 164 044 160 127 052 432 363 161 144 160 251 056 062 034 080 028 363 002 003 24 028 043 072 101 143 363 037 046 072 172 363 073 138 015 030 007 040 062 101 325 143 096 008 009 145 146 174 188 192 164 363 242 389 002 386 387 008 009 019 028 060 061 063 064 072 074 143 164 034 363 015 076 280 435 147 197 371 372 363 363 043 363 073 072 095 103 284 112 VCR Set-Up Code Number 034 117 034 161 016 146 043 046 124 125 117 031 072 145 040 012 023 039 043 101 040 035 037 129 101 028 145 108 024 117 101 117 024 003 022 102 041 145 040 111 116 117 005 007 010 065 108 110 120 108 012 023 039 043 034 053 059 101 006 029 035 017 025 027 034 036 037 046 101 129 131 153 162 116 145 003 010 008 009 145 034 034 072 147 063 107 109 144 145 132 136 155 115 102 101 106 114 020 012 123 034 034 012 045 024 004 026 150 018 034 043 063 137 160 020 034 145 145 012 015 066 101 020 102 043 048 043 130 150 055 060 012 050 152 145 101 014 048 034 047 024 101 145 101 106 114 020 012 123 034 024 034 003 009 017 106 102 067 034 068 041 156 164 145 067 069 012 156 145 101 027 030 145 145 101 003 010 014 034 053 072 102 134 139 145 045 046 059 040 020 059 061 151 020 045 046 051 049 168 053 145 034 102 024 034 012 023 039 043 048 101 040 043 031 ...