User manual VDO CYCLECOMPUTING C08

English Deutsch Français Italiano Español page Seite page 1-16 17-32 33-48 GB C 08 D C 08 F C 08 I C 08 E C 08 NL C 08 pagine 49-64 pagina 65-80 Nederlands pagina 81-96 ETRTO 47-305 47-406 34-540 47-507 23-571 40-559 44-559 47-559 50-559 54-559 57-559 37-590 20-571 16x1,75 20x1,75 24x1 3/8 24x1,75 26x1 26x1,5 26x1,6 26x1,75 26x1,9 26x2,00 26x2,125 26x1 3/8 26x3/4 WS in mm KMH 1272 1590 1948 1907 1973 2026 2051 2070 2089 2114 2133 2105 1954 WS in inch MPH 50,1 62,6 76,7 75,1 77,7 79,8 80,7 81,5 82,2 83,2 84,0 82,9 76,9 ETRTO 32-630 40-622 47-622 40-635 37-622 18-622 20-622 23-622 25-622 28-622 32-622 37-622 40-622 27x1 1/4 28x1,5 28x1,75 28x1 1/2 28x1 3/8 700x18C 700x20C 700x23C 700x25C 700x28C 700x32C 700x37C 700x40C WS in mm KMH 2199 2224 2268 2265 2205 2102 2114 2133 2146 2149 2174 2205 2224 WS in inch MPH 86,6 87,6 89,3 89,2 86,8 82,8 83,2 84,0 84,5 84,6 85,6 86,8 87,6 INSTALLATION AND OPERATION MANUAL - VDO CYTEC C 08 GB Preface Thank you for buying a VDO CYTEC bicycle computer. The more familiar you get with this model, the more enjoyable your trips are going to be. Please read thoroughly all the information provided in this manual. You are getting important and useful hints for operation to make you fully benefit from all the technical features of your VDO CYTEC bicycle computer. We wish you enjoyable trips and rides on your bike with VDO CYTEC CYCLE PARTS GMBH Mounting the system 1. Mounting the handlebar holder The handlebar holder fits handlebars of any diameter. Before mounting the system, decide if you will be using your left or right hand to operate the computer and then mount the handlebar holder on the respective side. Position the handlebar holder, insert the strap and adjust it by tightening the screw. Warning: Before tightening the handlebar holder, make sure to adjust the position of the computer head (inclination) when the LCDdisplay is best visible for you. Only when you find the best position tighten the screw. C 08 screw 1 2. Mounting the speed transmitter GB C 08 The sensor should be mounted on the same side of the fork as the holder is on the handlebar. Watch out: Do not tighten the cable ties yet! Accurately position the spoke magnet and the sensor first, then tighten the cable ties. 3. Mounting the spoke magnet Distance between magnet and sensor should be approx. 1-5 mm. 2 In case this distance is not achievable in the current positioning, slide the sensor and the magnet on the fork or spoke accordingly. GB C 08 1-5mm 1-5mm LOCK 4. Twist-Click mounting of computer onto holder UNLOCK The Twist-Click mounting has been exclusively developed for the new line of VDO CYTEC computers. The computerhead is put onto the handlebar and by a right turn of the computerhead (TWIST) fixed to the holder (CLICK). It is just as easy to remove the computerhead from the handlebar holder. Slightly push the computerhead down, twist it to the left, remove computerhead from handlebar holder. 1.LOCK 2.CLICK 1.PRESS 2.UNLOCK 3 5. Installing battery into computer head GB C 08 To save battery power, your VDO CYTEC comes with the battery not yet fitted. Prior to initial use you have to install the battery first. OPEN CLOSE If you find the computer is not functioning properly after a battery change, push the AC-button (Auto Clear) on the rear side of the computer to reset. 4 6. Information features of your VDO CYTEC C 08 Your VDO CYTEC C 08 provides you with following information: GB C 08 KMH-MPH TRP RID AVS MAX CLK ODO current speed indicated in either KMH or MPH, featuring automatic conversion into MPH trip counter, counts your trip distance up to 999,99 km or miles. trip timer, keeps track of the actual riding time featuring automatic start/stop function, up to 9:59:59 (hrs:min:sec) average speed, accurate to two decimal points. maximum speed, achieved during a ride, accurate to two decimal points. permanent comparison of current and average speed. Deviations are indicated by up/down arrows in the display. clock with 12 h or 24 h selectable display mode. odometer, counting distance ridden up to 99,999 KM or M. 5 GB C 08 7. Operating your VDO CYTEC C 08 Button / Key Covering Your VDO CYTEC C 08 has 2 buttons / keys Mode 1, Mode 2 Function TRP RID AVS MAX Function CLK ODO Mode 1 Mode 2 6 These buttons / keys have several functions. All functions of the respective buttons / keys outlined in the following chart below. Your display Button / Key indicates following to be pushed information TRP-AVS-RID-MAX MODE 1 CLK- ODO MODE 1 TRP-RID-AVS TRP CLK ODO CLK- ODO TRP-RID-AVS-MAX MODE 1 MODE 1 MODE 1 MODE 1 MODE 2 MODE 2 Length of pushing the button / key brief (0.1 sec) brief (0.1 sec) What is going on? GB C 08 TRP-RID-AVS-MAX MODE 2 next information from MODE 1 is indicated. computer changes display information from MODE 2 data to TRP-data of MODE 1 normal (1.5 sec.) TRP-RID-AVS are automatically rotated, one at a time displayed for 1.5 sec. long (5 sec) enter set-up mode for wheelsizes. long (5 sec) enter set-up mode for clock. long (5 sec) enter set-up mode for odometer. brief (0.1 sec) next information from MODE 2 is indicated. brief (0.1 sec) computer changes display information from MODE 1 data to MODE 2 data. CLK always being the first information indicated. long (5 sec) TRP-AVS-RID-MAX information reset to zero. 7 GB 8. Scroll function C To provide any information at a glance, your VDO CYTEC 08 C 08 features a scroll function. Calling up the scroll function automatically displays information for a period of 1.5 sec. Scroll function may be called upon if any of the following information is on display: TRP-AVS-RID. Scroll function is activated by pressing the MODE 1 button for 1.5 sec. SCROLL 9. Comparison of current and average speed Press MODE 1 1,5 sec. Start Scroll Your VDO CYTEC C 08 compares your current speed with your average speed. The outcome of this comparison can be seen in your display by the use of symbols. No matter which information is currently displayed, this data keeps you updated on the relation of your current speed and your average speed. Your current speed is faster than your average speed. Accuracy +/- 1 KMH/MPH 8 You are currently riding as fast as your average speed. Accuracy +/- 1 KMH/MPH Your current speed is slower than your average speed. Accuracy +/- 1 KMH/MPH 10. Set-up mode GB Your VDO CYTEC C 08 features the following set-up procedures wheelsize = WS clock = CLK odometers = ODO set-up starts out of TRP in display set-up starts out of CLK in display set-up starts out of ODO in display C 08 No matter which set-up mode is used for your VDO CYTEC , the procedure is the same. You can start the set-up mode for a certain display by pressing the MODE 1 button for 5 sec. With this MODE button you may also exit the set-up mode at any time. Once the set-up mode is activated, MODE 1 and MODE 2 buttons are covered with following instructions: MODE1 MODE2 changing from one enter display to the next enter display selection of figure to be entered, changing from KMH to MPH mode 11. Entering your wheelsize Your VDO CYTEC identifies wheelsize as WS = wheelsize. following default is entered wheelsize = WS = 2155 mm Watch out: Above default is automatically applied after a battery change. After a battery change, the correct wheelsize for your bike has to be re-entered How is the wheelsize precisely determined? Place the front wheel of your bike with the valve at the bottom, mark this position with a line and push your bike ahead until exactly one rotation of the front wheel is completed. Draw another line where the valve now is. Take a ruler and measure the distance between marks 1 and 2 which reflects the wheelsize = wheel-circumference. The figure measured (inches or mm) is the wheelsize to be entered into your computer 9 GB C 08 1x WS in mm / inch Programming (setting up) your wheelsize Step 1: Call TRP information in your display. Step 2: Press MODE 1 button for 5 sec. "WS" is displayed along with an alternating flashing symbol for KMH and MPH. Step 3: By pressing the MODE 2 button you can choose whether you want MPH or KMH readout on your display. Step 4: Once you have chosen your measuring unit, continue by pressing the MODE 1 button briefly (0.1 sec). Now, either the default value or the wheelsize value previously entered (WS) is displayed with the last number flashing. Step 5: With buttons MODE 1 and MODE 2 you can enter the wheelsize previously determined. (see set-up mode). Step 6: Once you have entered the last number for wheelsize, the computer automatically goes back to normal mode. You may also exit the set-up mode at any time by pressing the MODE 1 button. Watch out: When you exit set-up without having completed entering your data, the computer may well work with faulty values leading to misinformation in your display. 10 GB MODE 1 5sec. MODE 2 0,1sec. to change from KMH to MPH MODE 1 5sec. to quit C 08 MODE 1 0,1sec. switch to next MODE 1 to start to switch to quit MODE 2 to increase to change from KMH to MPH MODE 1 0,1sec. switch to next MODE 1 0,1sec. switch to next MODE 2 0,1sec. to increase MODE 1 0,1sec. switch to next MODE 1 0,1sec. switch to next 11 12. Setting the clock CLK GB C 08 Your VDO CYTEC C 08 features a clock with hour and minute display. 12 h or 24 h display selectable. To access the clock set-up mode proceed as follows: Step 1: call in the CLK information into your display Step 2: Press the MODE 1 button for 5 sec. The set-up mode for the clock starts. You will either see the figure "24" or "12" flashing reflecting the hour-mode programmed. To set up your clock use MODE 1 and MODE 2 buttons. (see set-up mode). MODE 1 5sec. to start MODE 2 0,1sec. MODE 1 0,1sec. switch to next MODE 2 MODE 1 0,1sec. switch to next MODE 1 5sec. to quit MODE 2 0,1sec. to increase MODE 1 0,1sec. switch to next 12 13. Programming (setting-up) your odometer ODO You can enter individual odometer values into your VDO CYTEC C 10 at any time, i.e. transferring data from your old computer into your new VDO CYTEC C 10 or after a battery change. Watch out: after a battery change, your data for total ODO is reset to zero. TIP: If you want to re-enter your totals after a battery change, take down the value for ODO before removing the battery. GB C 08 Step 1: Call information for ODO into your display. Step 2: Start the set-up mode for odometer by pressing the MODE 1 button for 5 sec. The last number is flashing. MODE 1 5sec. MODE 1 5sec. to quit MODE 2 0,1sec. to increase Entering data is done by MODE 1 and MODE 2 buttons. (see set-up mode) MODE 1 0,1sec. switch to next 13 GB C 08 14. Resetting information to zero The following information may be reset to zero with your VDO CYTEC C 08. TRP-RID-AVS-MAX These information here is simultaneously reset to zero. Information must be reset to zero by pressing the MODE 2 button for 5 sec. Watch out: Take care that the exact information to be reset is on display. If either of the following information, TRP, RID, AVS or MAX are displayed and you want to reset to zero by pressing the MODE 2 button, be aware that the remaining three information are simultaneously zeroed. 15. Stand-by-mode Your computer VDO CYTEC C 08 features a stand-by-mode in order to save battery power. Your computer changes into stand-by-mode if it has not received any speed impulses for 5 min or no button has been pressed in the same period of time. The time of day (CLK) is still displayed in stand-by-mode, though. By pressing any button or just continuing your ride, this will end stand-by-mode and return you to the appropriate mode. 16. Battery change Tip: Take down your totals and wheelsize prior to battery change. Changing the battery in the computer head. see 5 In case the computer is not properly functioning after a battery change, push the AC-button (Auto Clear) on the rear side of the computer to reset. Watch out: old batteries require special disposal Hg 14 17. Troubleshooting This chart outlines possible malfunctions, their causes and solutions. malfunction irregular LCD readout (i.e. after battery change) speed display does not appear possible cause computer software is not running smoothly check for proper distance between sensor and magnet cable from sensor to computer broken computerhead is incorrectly twisted on handlebar holder no wheelsize entered battery in computer empty temperatures below 5° C (40° F) dull display readout solutions press AC-button at the rear of computer head. readjusting distance between sensor and magnet. check cable and replace if necessary. place computerhead on handlebar holder and twist until detent (CLICK) enter your wheelsize check battery power and replace it if necessary. back in normal temperatures, display picks up working correctly. GB C 08 display fades or disappears 15 GB 18. Warranty We warrant VDO CYTEC models (sensor, computer head and handlebar holder) to the original purchaser for five years from date of C 08 purchase against defects in material and workmanship. This does not cover the batteries and defects resulting from normal wear and tear, improper care, accidents, abuse or alteration. Please take care to retain your receipt of purchase. In case of legitimate complaints, you are entitled to receive a comparable replacement model. Due to possible model changes, your model might not be available any more. You may contact your retailer or store where you purchased your VDO CYTEC or send the computer directly to us: CYCLE PARTS GMBH Grosse Ahlmuehle 33 D-76865 Rohrbach Technical specifications are subject to change. 19. Contents 1 computer head 1 handlebar holder with sensor, cable and screw 1 rubber shim for sensor mount 1 spoke magnet 5 cable ties 1 battery 3 V Type CR 2032 1 installation and operation manual 16