CD 2203 CD 27 03 CD 2253 CD 2803 User manual Mode d'emploi Bedienungsanleitung Gebruiksaanwijzing Istruzioni d'uso Instrucciones de manejo Modo de emprego Bruksanvisning Betjeningsvejledning Käyttöohje 3139 166 10722.2 11/02 gm www.vdodayton.com A 2 4 6 15 16 1 3 5 7 8 9 10 11 12 13 14 17 B 1 2 C D E 1 3 SAM (Software Access Mode) SAM TAVOL 1 START 1 MUTE 0 NAV OFF* BEEP OFF SDVC OFF* TEL OFF CLK ON RDSCLOCK CLOCKSET 12HCLOCK BRIGHT 1 ANGLE -1 GRAPHOFF* LOGICON LED ON EUROPE AF ON ... ... ... ... ... ... ... ... ... ... ... ... ... TAVOL 2 START 2 MUTE 1 NAV LOW* BEEP 1 SDVC 1* MUTE HI CLK OFF MANCLOCK ... ... ... ... ... ... ... TAVOL 3 START 3 MUTE 2 NAV HIGH* BEEP 2 SDVC 2* MUTE LO ....................... ....................... ....................... TAVOL 31 START 31 MUTE 5 ....................... ... ... BEEP 5 SDVC 4* HFREE HI SDVC 3* HFREE LO ... ... 24HCLOCK BRIGHT 2 ANGLE 0 GRAPH 1* ... ... ... BRIGHT 3 ANGLE +1 GRAPH 2* ........................ BRIGHT 6 . . . LOGICOFF ... ... ... LED OFF AMERICA . . . AF OFF ASIA MANUTUNE . . . AUTOTUNE REG ON . . . REG AUTO . . . REG OFF ... RDS OFF FM SCAN . . . PRE SCAN SCANTIME . . . MWLW ON LOCAL ... ... 5 SEC MWLW OFF DISTANT AUX IN* NEWS OFF* ... 10 SEC ... 20 SEC CHANGER* . . . NEWS ON* * Depending on version 4 ... BEFORE YOU START.... Thank you for purchasing this VDO Dayton product which has been designed and manufactured to the highest standards and subjected to rigorous testing. Kindly familiarise yourself with the product by reading this user manual. Keep this manual handy in your car for future reference. This manual covers the following models: CD 2203, CD 2253, CD 2703, CD 2803. The main differences between them are as follows: MP3 playback - only CD 2703, CD 2803. Navigation mute - only CD 2703, CD 2803. Speed Dependant Volume Control (SDVC) only CD 2253, CD 2703, CD 2803. IR Remote Control included - only CD 2803. 3D surround sound - only CD 2803. 2 channel Pre-out - only CD 2203, CD 2253, 4 channel Pre-out - only CD 2703, CD 2803. News Function - only CD 2703, CD 2803. Separate Source equalization - only CD 2703, CD 2803. CD Changer control or Auxiliary - only CD 2203, CD 2253, CD 2803. Graph - only CD 2803. Note : We reserve the right to make changes and improvements to any of the products described in this guide without prior notice. CONTENTS PAGE INSTALLATION ................................................. 5 PREPARATION ................................................. 5 MOUNTING ...................................................... 7 FRONT PANEL PRESENTATION ..................... 8 SECURITY ........................................................ 9 AUDIO ............................................................... 9 RADIO ............................................................. 10 RADIO DATA SYSTEM (RDS) ON FM ........... 11 CD, MP3* AND CDC* ..................................... 12 SPECIAL FUNCTIONS ................................... 13 SAM (Software Access Mode) ........................ 14 TROUBLE SHOOTING ................................... 16 INSTALLATION If your car is equipped with ISO connectors, simply insert them in the connectors of the car radio. If not, you can use an adaptor cable (Refer to the table on the separate installation manual). Ensure all cables are installed so that they cannot be damaged by sharp edges or moving parts. PREPARATION Voltage and polarity: The set must be connected to a 12V car battery with negative terminal to earth (car chassis). Installation in vehicles not fulfilling these requirements could result in malfunction, damage or fire. Warning: To prevent short-circuiting, disconnect the negative car battery terminal until the set has been mounted and connected (fig. 1 See separate installation card). CONNECTOR A** (fig. 2) Power supply connections · Red wire A7 : Connect to a permanent 12V supply. This is the main power supply. Ensure this connection can handle a current of 10A. · Yellow/red wire A4 : Connect to a switched 12V supply (switched on/off by car ignition). · Brown wire A8: Connect to earth (car chassis). Optional connections (fig. 2) · SDVC (Speed Dependent Volume Control)*: SDVC automatically increases and decreases the volume as a result of the car's speed. · Connect pin A1 to a signal from the speedometer of your car. Some cars are already prepared for it (e.g. certain VW & Vauxhall/Opel cars), please consult your dealer. If not, you may need a more detailed installation requiring extra equipment to enable your car to become compatible. Complies with 21 CFR 1040.10 5 ENVIRONMENT This booklet is printed on low-chlorine recyclable paper. IMPORTANT This device has been designed and produced according to applicable Safety Regulations. Please read carefully the instruction manual and use the device as intended. PREVENTIVE MAINTENANCE Cleaning the connectors To ensure good connection between the set and the detachable front, it is advisable to clean the connectors with a cotton swab slightly moistened with cleaning fluid or alcohol periodically. * Depending on version ** For this accessory, see your dealer This can only be accomplished by persons familiar with automotive electrical and mechanical systems. After Connection, see "SPECIAL FUNCTIONS' (page 13) for calibration procedure. · Electronic antenna/Motorised antenna : Green connector C2 (fig. 5) Steering wheel remote control You can connect certain car steering wheel mounted remote control to this set via an interface. Please consult your dealer for the correct interface. Pink wire (Telephone mute) · If your car telephone or the car kit of your mobile phone provides a mute signal, it can be used to automatically interrupt the set's sound output. ­ Connect the telephone mute wire to the Pink lead wire. ­ See 'SAM' (page 14); select option 'TEL' and set 'MUTE LO' or 'MUTE HI' (according to phone type) to automatically interrupt the set's sound output when using your car phone. Green wire (Navigation mute)* · If your car navigation computer provides a mute signal, it can be used to automatically interrupt the set's sound output during voice guidance. ­ Connect the Navigation mute wire to the Green lead wire. ­ See 'SAM' (page 14); select option 'NAV' and set 'LOW' or 'HIGH' according to the navigation computer's mute signal. Blue connector C3 for our analogue CD changer* or an Auxiliary equipment*. (available separately) · You can connect our analogue CD changer to this set (fig. 6) ­ Select option 'CHANGER' in 'SAM' (page 14). · You can connect the audio output of auxiliary equipment e.g. in-car video system (instead of a CD Changer) to this set (fig. 7) using a separate accessory cable. ­ Select option 'AUX IN' in 'SAM' (page 14). OTHERS CONNECTIONS Telephone in (fig. 8) · You can connect our hands-free phone kit (available separately) via the connector D. See mounting and connecting instructions for the hands-free kit. ­ Select option 'HFREE' and set 'HFREE LO' or 'HFREE HI' (according to phone type) in 'SAM' (page 14) to automatically interrupt the set's sound output when receiving or making a phone call. Connect pin A5 to the power supply for an electronic antenna or the control wire for the relay of an automatic motorised antenna. Use the small connector supplied. Do not use this connection for the supply lead of the aerial motor! · Pilot light : When the car headlights are switched on, the backlight to the power key remains illuminated (even when the radio is switched off). Connect pin A6 to the dashboard illumination wiring of the car. Use the small connector provided. Note : In certain car (e.g. VW Passat) the dashboard illumination is dimmed by a digitally modulated signal (PWM - Pulse Width Modulation). This PWM signal can disturb the illumination display of the car radio. In this case, connect pin A6 to the switch signal of the low beam headlight. Please consult your car dealers for more information. CONNECTOR B** (fig. 3) Loudspeakers (use 4 ohm loudspeakers only) · Do not connect any of the loudspeaker leads to earth or directly to a booster/amplifier without high level input or via an external fader! You can connect the loudspeaker leads directly to an amplifier with high level input. · Connecting 4 loudspeakers: Front Rear Left+ Green [B5] White [B7] LeftGreen/black [B6] White/black [B8] Right+ Grey [B3] Blue [B1] RightGrey/black [B4] Blue/black [B2] CONNECTOR C1 Yellow Connector C1 for Pre-out* (fig. 4) · Connect a power amplifier (with 2 or 4* additional loudspeaker) to this set with the RCA cable. ­ Connect Red socket to Right channel and white socket to Left channel. ­ Connect Blue wire to Amplifier Remote on/off. * Depending on version ** For this accessory, see your dealer 6 Infrared remote control You can use a VDO Dayton infrared remote control with this set. Please consult your dealer for the correct infrared remote control. MOUNTING METAL SLEEVE (fig. 10) · Install the metal sleeve (dimension 182x53 mm) in the dashboard. For optimal performance of the CD player, the metal sleeve should be positioned horizontally (between -10o and +30o). · Fix metal sleeve into place by pressing the metal tags outwards using a screwdriver. CONNECTING THE RADIO (fig. 9) · Ensure the battery is disconnected. · Insert aerial plug E into aerial socket (good reception is only possible with a good aerial). Fix antenna adaptor if needed. Use hook (J) on back of set to secure fixing. · Insert power supply connector A into socket A'. · Insert loudspeaker connector B into socket B'. · (optional) Remove the protective cover from socket C'. · (optional) Insert the yellow line-out connector C1 into socket C1'. · (optional) Insert the blue CD changer connector C3 into socket C3'. · (optional) Insert the green connector C2 into socket C2'. The green connector slides between the yellow connector C1 and the blue connector C3. You need at least one of these connections to keep C2 in place. MOUNTING RADIO This radio can be properly installed either from conventional Front Mounting or Rear Mounting. FRONT MOUNTING · Slide the radio into the metal sleeve until the springs at either side of the radio snap into the openings of the sleeve (fig. 11). · Finally reconnect the negative car battery terminal (fig. 12). REMOVING RADIO (using the two U- brackets supplied) · Remove the trimplate around the front panel. · Insert both U-brackets into the holes on the front of the set until they lock. Pull out the radio (fig. 13). REAR MOUNTING (fig. 14) · Remove the trimplate around the front panel and the side springs. · Select a position where the screw holes of the mounting bracket and the screw holes of the radio become aligned and tighten the screws at 2 places on each side. · Only use M5 screws that are not longer than 6mm. REPLACING FUSE (fig. 9) · Replace with a 10A blade-type fuse. The new fuse must be of exactly this value and type otherwise the set will not be adequately protected. Ignoring this procedure may lead to damage to the set, which will invalidate the guarantee. INTERFERENCE SUPPRESSION · Most modern cars have sufficient interference suppression. If you experience interference generated by the car, consult your garage. * Depending on version 7 FRONT PANEL PRESENTATION For illustration, see page 3, figure A. 1 ................ Short press: Switch on; mute/demute (when set is on) Long press: Switch off .................... Flip down the detachable panel .............. Desired sound source / / ...... Volume up / Audio mode ....... Volume down / Audio mode ............ Sound mode* ..... Short press: Sound mode, Long press: 3D sound* (only applicable for CD, CD changer* and MP3* mode) ...................... Traffic announcement ............... Waveband ............ Short press:Random playback on/off (CD or CD changer*) Short press: Toggle between Preset 1 & 2 (Tuner) Long press: Enter Preset store mode (Tuner) ........ Short press: Repeat track on/off (CD or CD changer*) Short press: Toggle between Preset 3 & 4 (Tuner) Long press: Enter Preset store mode (Tuner) ............ Short press: Track scan on/off (CD or CD changer*) Short press: Toggle between Preset 5 & 6 (Tuner) Long press: Enter Preset store mode (Tuner) .................. Autostore .............. Short press:Display mode Long press:Frequency scan or Preset scan (Tuner) / ............... Search lower/higher frequency (tuner); Next/previous track (CD, CD Changer* and MP3*) ................... Preset up/down (tuner); Next/previous disc (CD Changer*); Next/previous album (MP3*) ................... Software Access Mode ................ Bass Boost 2 3 4 5 6 7 8 9 10 11 12 13 14 15 / 16 17 * Depending on version 8 SECURITY For theft protection this set is provided with the following security features : DETACHABLE FRONT Take the detachable front with you when leaving the car. Keep it in its protective box. Al ...