User manual VIEWSONIC MW209 - QUICK START

Step 3 - ID Selection (Establishing a Wireless Connection) Press the Connect Button on the USB receiver and then on the mouse within 10 seconds. Note: Repeat this step when connecting the mouse for the first time and after replacing the batteries. MW209 ViewMateTM Wireless Travel Mouse Quick Start Guide Your ViewMate Wireless Travel Mouse is easy to use, and supports plug and play setup. Setup can be completed in 3 simple steps. Step 1 - Battery Installation: 1. Locate the two AAA sized 1.5 Volt batteries included in the ViewMate Wireless Travel Mouse package. 2. Remove the battery cover from the compartment on the back of your Optical Wireless Mouse. 3. Install the two batteries into the compartment. Make sure the + sign and the - sign on the batteries match the + sign and the - sign in the battery chamber. 4. Replace the battery compartment cover. Connect Button Connect Button Troubleshooting If your ViewMate Wireless Travel Mouse is not responding... 1. Make sure to install the batteries with correct polarity. 2. Make sure you have plugged in the USB receiver correctly. 3. Make sure the receiver is at least 8 inches (approx. 20 cm) away from other electrical devices such as computers, monitors, printers, etc. 4. Re-establish communication between the mouse and the receiver (see "ID Selection" above). Battery Life Like all battery-operated devices, the Optical Wireless Mouse is dependent on battery current for operation. Only alkaline batteries should be used. Since battery power is limited, batteries must be changed after a certain amount of time. Typically the batteries on this wireless device should last between 5 and 8 weeks, depending upon your own usage patterns and use of the on/off battery switch. Note: If the mouse pointer does not move after changing the batteries, verify you have inserted the batteries with the correct polarity. FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate your TV or radio receiving antenna. · Increase the separation between your TV and radio equipment and your mouse receiver. · Connect your computer equipment into a separate electrical outlet or circuit from your TV or radio equipment. · Consult the dealer or an experienced radio/TV technician for help. Important: FCC Radiation Exposure Statement This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. The device complies with the requirements of the EEC directive 89/336/EEC as amended by 92/31/EEC, R&TTE directive 1999/5/EC on Radio Equipment and Telecommunications Terminal Equipment Wireless and 93/68/EEC Art.5 with regard to "Electromagnetic compatibility," and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to "Safety." Caution: AVOID PROLONGED USE OF THE MOUSE WITHOUT BREAKS. Take regular breaks and keep a good posture. Consult your physician promptly if you notice any loss of motion or pain in your wrist when using the mouse. Step 2 - Connecting the Receiver: USB Installation (Note: If your computer uses Microsoft Windows 95 or Windows NT Workstation, please be aware that these operating systems do not support USB.) 1. Make sure that your computer is turned on. 2. Plug the USB receiver into an empty USB port and follow the on-screen instructions. USB Receiver Étape 3 ­ Choix d'identité (Établir une connexion sans fil) Appuyez sur le bouton du récepteur USB et puis celui de la souris dans un délai de 10 secondes. Note : Répétez cette étape lorsque vous branchez la souris pour la premiè. MW209 ViewMateTM Wireless Travel Mouse Guide Rapide De Début Votre ViewMate Travel Mouse est très facile à utiliser, et supporte l'installation branchez et ça marche. L'installation peut se faire en trois simples étapes. Étape 1 ­ Installation de la batterie: 1. Trouvez les deux batteries AAA de 1,5V comprises dans le paquet du ViewMate Wireless Travel Mouse. 2. Retirez le couvercle de la batterie du compartiment situé à l'arrière de votre Souris Optique sans Fil. 3. Installez les deux piles dans compartiment. Assurez-vous que les symboles + et ­ sur les batteries correspondent au symbole + et ­ dans le compartiment de la batterie. 4. Replacez le couvercle du compartiment de la batterie. Bouton de connexion Bouton de connexion Dépannage Si votre ViewMate Wireless Travel Mouse ne répond pas... 1. Assurez-vous que la polarité des batteries est bonne. 2. Assurez-vous d'avoir bien branché le récepteur USB. 3. Assurez-vous que le récepteur se trouve à au moins 20 cm (approx. 8 pouces) d'autres dispositifs électriques tels que des ordinateurs, des moniteurs, des imprimantes, etc. 4. Rétablissez la communication entre la souris et le récepteur (voir « Choix d'identité » ci-dessus) Durée de la pile Comme tous les dispositifs à batterie, la Souris Optique sans Fil dépend de l'alimentation par batterie pour son fonctionnement. Seules des batteries alcalines devraient utilisées. Puisque la puissance d'une batterie est limitée, les batteries devraient être remplacées au bout d'un certain temps. Typiquement, les batteries de ce dispositif devraient durer de 1.5 à 2 mois selon l'utilisation. Note : Si la flèche de la souris ne bouge pas après avoir changé les batteries, vérifiez leur polarité dans le compartiment. Étape 2 ­ Branchement du récepteur : Installation USB (Note : Si votre ordinateur utilise Microsoft Windows 95 ou Windows NT Station de Travail, veuillez noter que ces systèmes ne supportent pas l'USB.) 1. Assurez-vous que votre ordinateur est allumé. 2. Branchez le récepteur USB dans un port USB libre et suivez les instructions à l'écran. Récepteur USB Paso 3 ­Selección de ID (Estableciendo una Conexión Inalmbrica) Presione el Botón Conectar en el receptor USB y después en el ratón 10 segundos después. Nota: Repita este paso al conectar el ratón por primera vez y después de cambiar las pilas. MW209 ViewMateTM Wireless Travel Mouse Guía Rápida Del Comienzo Su Travel Mouse ViewMate Inalámbrico es facíl de usar, y soporta configuración "plug and play". La configuración puede ser completada en 3 simples pasos. Paso 1 ­ Instalación de las Pilas: 1. Ubique las dos pilas tamaño AAA 1.5 Volt. Incluidas en la caja del Travel Mouse View Mate Inalámbrico. 2. Quite la tapa de las pilas del compartimento en la parte traserla de su Ratón Óptico Inalámbrico. 3. Instale las dos pilas en el compartimento. Asegúrese de que los signos + y ­ en las pilas coincidan con los signos + y ­ en el hueco de las pilas. 4. Vuelva a colocar la tapa del compartimento. Botón Conectar Botón Conectar Solución de Problemas Si su Travel Mouse ViewMate Inalámbrico no está respondiendo... 1. Asegúrese de instalar las pilas con la polaridad correcta. 2. Asegúrese de haber enchufado el receptor USB correctamente. 3. Asegúrese de que el receptor esté al menos a 8 pulgadas (aprox. 20 cm) de otros dispositivos eléctricos como ordenadores, monitores, impresoras, etc. 4. Re-establezca la comunicación entre el ratón y el receptor (ver "Selección de ID" arriba) Vida de las Pilas Como todos los dispositivos que funcionan con pilas, el Ratón Óptico Inalámbrico depende de la corriente de las pilas para funcionar. Sólo se deberían usar pilas alcalinas. Debido a que la energía de las pilas es limitada, las pilas deben ser cambiadas después de un periodo de tiempo. Normalmente, las pilas en este dispositivo inalámbrico deberían durar entre 1.5 y 2 meses dependiendo del uso. Nota: Si el puntero del ratón no se mueve después de cambiar las pilas, compruebe que haya insertado las pilas con la polaridad correcta. Paso 2 ­ Conectando el Receptor: Instalación USB (Nota: Si su ordenador usa Microsoft Windows 95 o Windows NT Workstation, por favor tenga en cuenta que estos sistemas operativos no soportan USB.) 1. Asegúrese de que su ordenador esté encendido. 2. Enchufe el receptor USB en un puerto vacío USB y siga las instrucciones en pantalla. Receptor USB MW209 ViewMateTM Wireless Travel Mouse ViewMate Wireless Travel Mouse «plug and play» . 1. : 1. ( AAA, 1,5 , ViewMate Wireless Travel Mouse). 2. . 3. . , «+» «-» «+» «-» . 4. . 3. ( ) USB, ( , 10 ) . : , . ViewMate Wireless Travel Mouse ... 1. , . 2. USB. 3. , , 20 (8 ) (, , ..). 4. (. « 3. », ). ( ) , . . . . , , , , 1.5 2 , . : , . 2. : USB (. Microsoft Windows 95 Windows NT Workstation, , USB) 1. , . 2. USB USB. , . Customer Support/Service clientèle/Servicio de atención al cliente/ For technical support or product service, see the table below or contact your reseller NOTE: You will need the product serial number. Pour toute question relative au support technique ou à l'entretien du produit, reportez-vous au tableau ci-après ou contactez votre revendeur. REMARQUE: vous devrez fournir le numéro de série du produit. Para obtener asistencia técnica o para reparar el equipo, consulte la tabla siguiente o póngase en contacto con el distribuidor. NOTA: necesitará el número de serie del producto. . , , , . : . Country Australia / New Zealand Canada Chile / Mexico Office Name ViewSonic Australia ViewSonic Corporation ViewSonic Corporation Address Unit 3, 44 Dickson Ave., Artarmon, NSW 2064, Australia 381 Brea Canyon Rd., Walnut, CA 91789, USA 381 Brea Canyon Rd., Walnut, CA 91789, USA Phone 1800 880 818 (AUS) 0800 008 822 (NZ) 1-866-463-4775 1230-020-3464 (Chile) 866-823-2004 (Mexico) 0086-021-62375252 800-8820-3870 0086-021-62473182 Tel: +44(0)1293 643-900 Fax: +44(0)1293 643-910 +852 2268-6878 +65 6273-4018 0800-061-198 0800833648 1-800-888-8583 www.viewsonic.com.cn Web Site / Service Email www.viewsonic.com.au service@au.viewsonic.com www.viewsonic.com/contactus www.viewsonic.com/contactus China ViewSonic China Limited 1468 36 3608 200040 Europe, Middle East, Baltic countries, and North Africa Hong Kong Singapore Taiwan UK USA Contact your reseller ViewSonic Hong Kong Ltd. ViewSonic Singapore Pte Ltd. ViewSonic International Corporation ViewSonic Europe Limited/UK ViewSonic Corporation ViewSonic House Fleming Way, Crawley West Sussex RH10 9GA, United Kingdom Suite 811, East Wing, Tsimshatsui Centre, 66 Mody Road, TST East Kowloon, Hong Kong 221 Henderson Road, #04-08 Henderson Building. Singapore 159557 192 9 ViewSonic House Fleming Way, Crawley West Sussex RH10 9GA, United Kingdom 381 Brea Canyon Rd., Walnut, CA 91789, USA www.viewsoniceurope.com service-eu@viewsoniceurope.com www.hk.viewsonic.com www.viewsonic.com.sg service@sg.viewsonic.com www.viewsonic.com.tw service@tw.viewsonic.com www.viewsonic.co.uk service-eu@viewsoniceurope.com www.viewsonic.com/contactus Please register your product on the Internet at: www.viewsonic.com. Veuillez enregistrer votre produit par le biais d'Internet à l'adresse suivante: www.viewsonic.com Regístrelo a través de Internet en: www.viewsonic.com. : www.viewsonic.com. Step 3 - ID Selection (Establishing a Wireless Connection) Press the Connect Button on the USB receiver and then on the mouse within 10 seconds. Note: Repeat this step when connecting the mouse for the first time and after replacing the batteries. MW209 ViewMateTM Wireless Travel Mouse Quick Start Guide Your ViewMate Wireless Travel Mouse is easy to use, and supports plug and play setup. Setup can be completed in 3 simple steps. Step 1 - Battery Installation: 1. Locate the two AAA sized 1.5 Volt batteries included in the ViewMate Wireless Travel Mouse package. 2. Remove the battery cover from the compartment on the back of your Optical Wireless Mouse. 3. Install the two batteries into the compartment. Make sure the + sign and the - sign on the batteries match the + sign and the - sign in the battery chamber. 4. Replace the battery compartment cover. Connect Button Connect Button Troubleshooting If your ViewMate Wireless Travel Mouse is not responding... 1. Make sure to install the batteries with correct polarity. 2. Make sure you have plugged in the USB receiver correctly. 3. Make sure the receiver is at least 8 inches (approx. 20 cm) away from other electrical devices such as computers, monitors, printers, etc. 4. Re-establish communication between the mouse and the receiver (see "ID Selection" above). Battery Life Like all battery-operated devices, the Optical Wireless Mouse is dependent on battery current for operation. Only alkaline batteries should be used. Since battery power is limited, batteries must be changed after a certain amount of time. Typically the batteries on this wireless device should last between 5 and 8 weeks, depending upon your own usage patterns and use of the on/off battery switch. Note: If the mouse pointer does not move after changing the batteries, verify you have inserted the batteries with the correct polarity. FCC Statement Step 2 - Connecting the Receiver: USB Installation (Note: If your computer uses Microsoft Windows 95 or Windows NT Workstation, please be aware that these operating systems do not support USB.) 1. Make sure that your computer is turned on. 2. Plug the USB receiver into an empty USB port and follow the on-screen instructions. USB Receiver This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate your TV or radio receiving antenna. · Increase the separation between your TV and radio equipment and your mouse receiver. · Connect your computer equipment into a separate electrical outlet or circuit from your TV or radio equipment. · Consult the dealer or an experienced radio/TV technician for help. Important: FCC Radiation Exposure Statement This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. The device complies with the requirements of the EEC directive 89/336/EEC as amended by 92/31/EEC, R&TTE directive 1999/5/EC on Radio Equipment and Telecommunications Terminal Equipment Wireless and 93/68/EEC Art.5 with regard to "Electromagnetic compatibility," and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to "Safety." Caution: AVOID PROLONGED USE OF THE MOUSE WITHOUT BREAKS. Take regular breaks and keep a good posture. Consult your physician promptly if you notice any loss of motion or pain in your wrist when using the mouse. ( ) USB MW209 ViewMateTM Wireless Travel Mouse ViweMate 1. ViewMate 1.5 (AAA) 2. 3. 4. ViewMate ... 1. 2. USB 3. 8 20 4. 1.5~2 : LED USB USB ( Windows 95 Windows NT workstation USB) 1. 2. USB USB USB 3 ID USB 10 MW209 ViewMateTM Wireless Travel Mouse ViewMate 3 1 1. View Mate 2 1.5 AAA 2. 3. 4. View Mate ... 1. 2. USB 3. 8 20 4. " ID" 1.5 2 2 USB USB ( Windows 95 Windows NT Workstation USB ) 1. 2. USB USB USB Customer Support/ / For technical support or product service, see the table below or contact your reseller NOTE: You will need the product serial number. : Country Australia / New Zealand Canada Chile / Mexico Office Name ViewSonic Australia ViewSonic Corporation ViewSonic Corporation Address Unit 3, 44 Dickson Ave., Artarmon, NSW 2064, Australia 381 Brea Canyon Rd., Walnut, CA 91789, USA 381 Brea Canyon Rd., Walnut, CA 91789, USA Phone 1800 880 818 (AUS) 0800 008 822 (NZ) 1-866-463-4775 1230-020-3464 (Chile) 866-823-2004 (Mexico) 0086-021-62375252 800-8820-3870 0086-021-62473182 Tel: +44(0)1293 643-900 Fax: +44(0)1293 643-910 +852 2268-6878 +65 6273-4018 0800-061-198 0800833648 1-800-888-8583 www.viewsonic.com.cn Web Site / Service Email www.viewsonic.com.au service@au.viewsonic.com www.viewsonic.com/contactus www.viewsonic.com/contactus China ViewSonic China Limited 1468 36 3608 200040 Europe, Middle East, Baltic countries, and North Africa Hong Kong Singapore Taiwan UK USA Contact your reseller ViewSonic Hong Kong Ltd. ViewSonic Singapore Pte Ltd. ViewSonic International Corporation ViewSonic Europe Limited/UK ViewSonic Corporation ViewSonic House Fleming Way, Crawley West Sussex RH10 9GA, United Kingdom Suite 811, East Wing, Tsimshatsui Centre, 66 Mody Road, TST East Kowloon, Hong Kong 221 Henderson Road, #04-08 Henderson Building. Singapore 159557 192 9 ViewSonic House Fleming Way, Crawley West Sussex RH10 9GA, United Kingdom 381 Brea Canyon Rd., Walnut, CA 91789, USA www.viewsoniceurope.com service-eu@viewsoniceurope.com www.hk.viewsonic.com www.viewsonic.com.sg service@sg.viewsonic.com www.viewsonic.com.tw service@tw.viewsonic.com www.viewsonic.co.uk service-eu@viewsoniceurope.com www.viewsonic.com/contactus Please register your product on the Internet at: www.viewsonic.com. www.viewsonic.com : www.viewsonic.com