Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. 2. 3. 4. 5. 6. Read and understand all instructions. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool). Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from overheating, these openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation where proper ventila-tion is not provided. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. take it to an authorized service facility. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently used. 7. 8. 9. 10. To reduce the risk of electric shock, do not disassemble this product, but 11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 12. Unplug this product from the wall outlet and refer servicing to a VTech authorized service facility under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage and will often require extensive work by a VTech authorized technician to restore the product to normal operation. E. If the product has been dropped and the cabinet has been damaged. F. If the product exhibits a distinct change in performance. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lighting. Do not use the telephone to report a gas leak in the vicinity of the leak. 13. 14. VTECH COMMUNICATIONS INC SERVICE DEPT. at 1-800-595-9511. In Canada, call VTech Telecommunications Canada Ltd. at 1-800-267-7377. SAVE THESE INSTRUCTIONS Introduction The v 2651 is an advanced cordless telephone that operates in the 2.4GHz frequency range. Your v 2651 is capable of supporting up to a maximum of 4 Handsets. Using additional Handsets, up to three people can be conferenced on a call (2 Handsets and the Base Speakerphone), or two extensions can be conferenced on a call, while two other extensions can be talking internally, using the Intercom feature. This manual is designed to familiarize you with the v 2651 cordless telephone. We strongly recommend you read the manual before using your phone. To order additional system Handsets(model#v 2600), battery packs, or headsets, call VTech Communications Inc at 1-800-595-9511. IMPORTANT Please record the Base ID#(BS ID) printed on the underside of the v 2651 Base in the space below. Please be certain to include all 15 digits/characters. Base ID # STOP!! If you have questions about this product, or if you're having difficulty with setup or operation, do not return your phone to the store. Call our Customer Support Center at 1-800-595-9511 In Canada, call 1-800-267-7377 ! Parts Check List Base Unit 5 Battery Pack Handset 6. User's Manual AC Power Adapter 7. Wall Mounting Bracket Telephone Cord To purchase replacement battery packs, call VTech Communications Inc at 1-800-595-9511. In Canada, call VTech Telecommunications Canada Ltd. at 1-800267-7377. 1. 2. 3. 4. Handset Base Unit Telephone Cord Wall mounting Bracket Users Manual Battery Pack AC Power Adapter " The Handset Layout 1 2 3 4 5 6 7 8 9 10 11 12 1. 2. 3. 4. 5. 6. 7. Antenna Earpiece Scroll Keys Headset Jack (2.5mm) On (Flash) Dialing Keys (0-9, *, #) Handsfree Speakerphone 8. LCD Display 9. Menu/Select 10. Off (Clear) 11. Battery Compartment 12. Intercom 13. Microphone # The Base Unit Layout 10 12 11 Speakphone Key Charge Contacts CORDLESS TELEPHONE VTECH TELECOMMUNICATIONS LTD. DC 9V 500mA CLASS 2 POWER SOURCE ONLY 7. 8. 9. 10. 11. 12. Telephone Jack DC Connector Volume In Use Flash 1. 2. 3. 4. 5. 6. Charging LED MODEL: 2651 VTECH TELECOMMUNICATIONS LTD. MANUFACTURED IN CHINA HAC FCC ID: EW72230P2 COMPLIES WITH 47 CFR PART 68 REGISTRATION NO.: US: 6BXWI01B80-XXXXXX RINGER EQUIVALENCE: 0.1B USOC JACK: RJ11C/W THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. Dialing Keys (0-9, *, #) Intercom Redial Mute 3 2 1 4 5 6 7 8 9 $ Setup Connecting Power to Base Unit CORDLESS TELEPHONE To AC outlet VTECH TELECOMMUNICATIONS LTD. DC 9V 500mA CLASS 2 POWER SOURCE ONLY To telephone outlet AC adapter To telephone jack Plug the AC power adapter into an electrical outlet, and the DC connector into the back of the base unit. CAUTION:Use only the VTech power supply provided with your VTech unit. IMPORTANT: FOR MAXIMUM PERFORMANCE OF YOUR CORDLESS TELEPHONE SYSTEM: 1. Choose a central location for your Base Unit. 2. Install your Base Unit and Extension Handsets away from electronic equipment, such as personal computers, television sets and microwave ovens. 3. In locations where there are multiple cordless telephones, separate Base units as much as possible. 4. Install your telephone equipment away from heat sources and sunlight. 5. Avoid excessive moisture,dust orextreme cold. % Getting Started Getting Started Setup Installation of Battery Pack in Handset Follow the steps below: 1. 2. 3. 4. Remove the battery cover by pressing on the indent and sliding downward. Align the two holes in the plug with the socket pins. Insert the plug into socket. Place the battery pack into the compartment with the wires coming out of one of the bottom corners of the pack. Replace the battery cover by sliding it upwards. If the new battery pack is not already charged, place the Handset in the Base unit, or a remote charging stand, and allow it to charge for 12 hours. After initial charge, a maintenance charge of 8 hours should be sufficient. The original Handset that is shipped with your v 2651 system will be automatically registered to the Base. This Handset is HANDSET 1. As you register additional Handsets to the system, they will be assigned extension numbers in the following order: HANDSET 2, HANDSET 3, and finally HANDSET 4. After a Handset battery pack is installed, the Handset will automatically begin SEARCHING FOR BASE (if previously registered), or it will prompt you to ENTER BASE ID to register the new Handset. & Charging Of Handset Battery Pack The Handset of your v 2651 cordless telephone is powered by a rechargeable battery pack. It charges automatically whenever the Handset is in the Base Unit. Maximum talk time on a full charge is 7.5 hours. Maximum standby time is over 5 days. You should charge the battery pack for 12 hours when you first receive your phone. You'll know the battery pack needs charging when: · The low battery message is displayed : · The handset seems completely dead, the LCD is completely clear and does not activate when you press the keys. IMPORTANT: 1. 2. 3. 4. Do not dispose of a battery pack in a fire, the cell may explode. Do not open or mutilate the battery pack. Toxic substances may be released, causing harm to eyes or skin. Exercise care in handling battery packs in order to prevent an accidental short of the charge contacts, potentially causing the battery pack to overheat. Do not dispose of this battery pack into household garbage. For information concerning proper battery recycling or disposal, please contact your local Recycling Center or Disposal Service. Connecting to phone line Plug one end of the telephone line cord into the jack on the back of the Base unit. Plug the other end of this cord into the wall telephone jack. Checking for dial tone After the battery is charged press ON on the Handset. The Phone icon will appear on the handset display, and you will hear dial tone. If not, see In Case of Difficulty. ' Getting Started Getting Started Walling Mounting The Wall Mount bracket is designed for use on standard Wall Mount plates only. 1. 2. 3. 4. Line up the tabs on the wall mount adapter with the holes on the bottom of the base unit. Snap the wall mount bracket firmly in place. Plug the AC adapter into an electrical outlet, and the DC connector to the bottom of the base unit. If the handset battery pack has not been charged previously, place the handset in the base unit cradle, and allow it to charge for 12 hours. Connect the telephone line cord to the jack on the bottom of the base unit, and the other end to the telephone jack. Mount the base unit on the wall. Position the base unit so the mounting studs will fit into the holes on the wall mount bracket. Slide base unit down on the mounting studs until it locks into place. 3 To telephone outlet 2 VTECH TELECOMMUNICATIONS LTD. DC 9V 500mA CLASS 2 POWER SOURCE ONLY To telephone jack CORDLESS TELEPHONE AC adapter 1 Registration of Additional Handsets Registration And Operation Of The VTech v 2600 Accessory Handset NOTE: Your v 2651 Handset comes registered to the Base Unit. The following information explains how to register additional Handsets to your v 2651 system. Your VTech v 2651 system can operate up to 4 Handsets. The VTech accessory Handset consists of the following: Setup Of The v 2600 Accessory Handset 1. 2. Plug the AC power adapter into an electrical outlet. Install the battery pack, as described previously. To order additional Handsets (model v 2600) Call 1-800-5959511. In Canada, call 1-800-2677377. Getting Started Getting Started Registration of Additional Handsets Enter Base ID Code 1. After charging the Handset, if the screen displays SEARCHING FOR BASE, press NEW. You will see ENTER BASE ID. If the screen already says ENTER BASE ID, go to step 2. 2. Enter the 15 digit BASE Unit ID Code, located on the underside of the Base Unit. 3. Press OK. The Handset will display: PLEASE WAIT!! 4. Wait approximately 15 seconds. The Handset will display: FOUND BASE NOTE: Occasionally, it will take longer than 15 seconds for the Handset to find the Base Unit.This is normal. If the Handset displays: BASE BUSY TRY LATER, this indicates that the system is in use. Wait until the Base Unit is in the idle (on hook) mode, and repeat steps 2 to 4. Congratulations! You can now enjoy the benefits of your VTech multi-Handset system. Handset and Base Indicators Handset Icons Icon Description Line In Use indicator On steady with no number next to it when a parallel set is in use. On steady with one or more numbers next to it, indicating which extensions are using the line. For example, 12 indicates that Handset 1 and Handset 2 are on an outside call. Intercom indicator On steady with the extension numbers currently on an intercom call. For example, 02 indicates that the Base and Handset 2 are on an intercom call. Battery indicator Cycles (Low, Medium, and High) when Handset battery is charging. Flashes when a low battery condition is detected. M H E Mute indicator On steady when the Handset microphone is muted. Hold indicator On steady when the line is on hold. Range Extender indicator On steady when the Range Extender is on. R Handset Registration indicator FF is displayed when a Handset is either not registered, or is searching for a Base unit. ! Basic Operation Handset and Base Indicators Base LEDs LED In Use Description · Lights when line is being used by any extension of the v 2651 system. · Flashes when another telephone on the same ...