INTRODUCTION Congratulations! You have purchased one of the most sophisticated cordless telephones on the market! The SBC9030 has been designed to offer a new standard in cordless telephone technology. Unlike most other cordless phones, the SBC9030 digitizes your voice using advanced digital voice coding to provide noise and distortion free performance. In most conditions you will not be able to tell you are using a cordless phone. Gone are the annoyances of static, interference and having to listen to other people's conversations on your cordless phone. The SBC9030 scrambles your voice before it transmits it. This allows you the security of knowing that no one can tune in and eavesdrop on your conversations. The SBC9030 decodes and displays name and number Caller ID (CID) information where available and when subscribed to. The alpha-numeric display will show both the name and number of the calling party (when available). Up to 15 name characters and/or 11 phone number digits can be displayed on the LCD. With the SBC9030, the user can easily answer a call by pressing any key other than the OFF, VOLUME keys or 3 PPU keys. In addition, the handset keypad and LCD illuminate while the handset rings to signal an incoming call. This is very useful in a dark environment. The SBC9030 includes a Speakerphone and keypad on the Base Unit. This enables you to make and receive calls hands-free at the Base. In 1 addition, the Intercom feature allows twoway communication between the Handset and Base Unit. Pressing INTERCOM on the Base can also assist you in locating a misplaced Handset. The SBC9030 uses special memory in both the Base Unit and Handset which is not susceptible to power failures. This provides permanent storage of all speed dial numbers, CID information as well as the Base Unit and Handset security codes. When a spare battery(not included) is installed in the Base Unit, the SBC9030 uses this battery to provide operational backup in case of power failure. In this way, you have access to all normal phone functions during a total power outage. Calls can still be placed and received without interruption. More than 4 hours backup will be possible with a fully charged battery in the Base Unit. The phone will also alert you when you are Out of Range even when you're not using the phone! INTRODUCTION SPECIAL FEATURES · 900 MHz Operation. · Direct Sequence Spread Spectrum - Digital Cordless Telephone. · Digitally-Scrambled Voice Communication. · Simultaneous display of Name, Number, and Time/Date stamp for Caller ID. · 50 Caller ID memory locations. · Voice announce Caller ID · 4-row by 16-character dot matrix alphanumeric display. · Backlit display on handset. · Backlit handset keypad. · Three Soft Keys which allow the user to access different functions, depending on which mode the phone is currently in (i.e. Caller ID, Memory Programming, etc.). · Smart Dialing from Caller ID memory eliminates the need to pre-program your local area code. · 25 locations Programmable Memory for 16-Digit Phone Number. Each location can also be assigned up to a 15 character name. · Out of Range indication while the handset is in use or in standby mode. · Handset speakerphone. · Speakerphone and keypad on the Base Unit. · Two-way intercom between Handset and Base Unit. · Removable handset battery pack. · Spare battery charger in the base unit. · Complete battery back-up in case of power failure (with additional battery pack installed in base). · Face up or down Handset charging. · Easy answer - When the phone 2 rings, simply press any key other than OFF, the Volume keys or the 3 PPU keys on the handset to answer. Pressing the OFF key on handset during incoming ring will stop the ringing. Auto hang up when returning the handset to the base cradle. 24-Bit Digital Security Code. Low Battery Detect and Warning indicator. Tone or Pulse dialing. Visual Message Waiting Indication (VMWI) for use with voicemail service. Up to 7 hours of continuous talk time or 14 days standby time. 8-level Volume control on Handset. Programmable Ringer Tones and Volume. Headset Compatible, for use with 2.5mm headsets. · · · · · · · · · · This manual is designed to familiarize you with the SBC9030. We strongly recommend you read the manual before using your phone. INTRODUCTION PARTS CHECK LIST 1.Base Unit, Handset, Belt Clip and AC adapter 2.One-Line Telephone Cord 3.Battery Pack 4.Wall mount accessory To purchase replacement battery packs, call Customer Service at 800667-2118. MEMORY AUTO CALL RETURN *69 3-WAY CALLING AUTO BUSY REDIAL *66 MESSAGE POWER IN-USE CHARGE SPARE BATT FLASH PHONE FLASH OFF 1 2 abc ghi 3 def MEMORY 1 2 ABC GHI 3 DEF 4 5 jkl 8 tuv 0 oper 6 mno REDIAL 4 5 8 JKL 6 MNO 9 WXYZ 7pqrs tone 9wxyz HOLD 7 PQRS TONE TUV 0 OPER 3-WAY CALLING AUTO BUSY REDIAL *66 MUTE VOL AUTO CALL RETURN *69 INTERCOM INTERCOM SPEAKER SPEAKERPHONE MIC Handset Base Unit Telephone Cord Belt Clip Wall mount accessory Battery Pack AC Adapter 3 FCC REGULATIONS This equipment complies with Parts 15 and 68 of the Federal Communications Commission (FCC) rules for the United States. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The underside of the Base Unit containing engravements of either the FCC registration number and Ringer Equivalence Number (REN), or the IC registration number . You must, upon request, provide this information to your local telephone company. This equipment is compatible with inductively coupled hearing aids. Should you experience trouble with this telephone equipment, please contact: Customer Service at 800-667-2118 The telephone company may ask you to disconnect this equipment from the line network until the problem has been corrected. rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Part 15 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance's could void the user's authority to operate the equipment. The equipment has been tested and found to comply with part 15 of the FCC 4 FCC REGULATIONS FCC Part 68 The FCC requires that you connect your cordless telephone to the nationwide telephone network through a modular telephone jack (USOC RJ11C, RJ11W or RJ14). Your telephone company may discontinue your service if your equipment causes harm to the telephone network. They will notify you in advance of disconnection, if possible. During notification, you will be informed of your right to file a complaint with the FCC. Occasionally, your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the operation of your equipment. If so, you will be given advance notice of the change to give you an opportunity to maintain uninterrupted service. The Base Unit contains no user serviceable parts. The Handset contains a user replaceable battery pack. If it is determined that your telephone equipment is malfunctioning, the FCC requires that it not be used and that it be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents or by others who may be authorized by the FCC. For repair procedures, follow the instructions outlined under the Limited Warranty. This equipment may not be used on coin service provided by the phone company or Party Lines. The REN is useful in determining the number of devices you may connect to your telephone line and still enable the devices to ring when you receive a call. The general rule is that the REN value should not exceed 5.0 total; however, contact your local telephone company for the specific number in your area. 5 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1.Read and understand all instructions. 2.Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4.Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool). 5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 6.Slots and openings in the cabinet on the back or bottom are provided for ventilation.To protect it from overheating, these openings must not be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation where proper ventilation is not provided. 7.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. 6 8.Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it. 9.Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 10.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltage or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently used. 11.Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C.If the product has been exposed to rain or water. TIONS IMPORTANT SAFETY INSTRUCTIONS D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage and will often require extensive work by an authorized technician to restore the product to normal operation. E. If the product has been dropped and the cabinet has been damaged. F. If the product exhibits a distinct change in performance. 13.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lighting. 14.Do not use the telephone to report a gas leak in the vicinity of the leak. SAVE THESE INSTRUCTIONS 7 INSTALLING THE BATTERY PACK The Handset of your SBC9030 is powered by a rechargeable battery pack. It charges automatically whenever the Handset is in the Base Unit. You should charge the battery pack for 16 hours when you first receive your phone. You'll know the battery pack needs charging when: · The low battery message is displayed: Alternatively, if a spare battery pack has been charging in the Base Unit, simply exchange the drained Handset battery pack with the fully charged replacement battery pack from the Base Unit charger. Place the drained Handset battery pack into the Base Unit charger so that it will charge. The Base Unit spare battery charger does NOT charge a battery pack as quickly as the main Handset battery charger. A full charge requires 24 hours. A WORD ABOUT RECHARGEABLE BATTERIES · The Handset seems completely dead, the LCD is completely clear and does not activate when you press the keys. Your Ni-Cd battery pack recharges whenever the Handset is returned to the Base Unit. TO CHARGE THE BATTERY ...