MEMORY DIALING To store a number in memory: 1. Press MEM . 2. Enter the name. Then press 3. Enter the phone number . Then press SELECT. The number is now stored. To dial a number from memory: 1. Press until you see the desired number. 2. Press PHONE. The displayed number will be dialed. Press OFF to end your call. SELECT CID OFF OFF PHONE FLASH HOLD HOLD PHONE 1 4 GHI 7PQRS TONE 2 ABC 5 JKL 8 TUV 0 OPER PROG CHAN 3 DEF 6 MNO 9WXYZ CHANGING CHANNELS If you experience noise or interference during a conversation, press PROG/CHAN to switch to a clear channel. MEM NEW REDIAL PAUSE FLASH You can use your VT9161 cordless telephone with services such as Call Waiting. Press PHONE/FLASH to swith to the incoming call. REDIAL PROG/CHAN MEM PAGE From the base unit, press PAGE to signal the person at the handset. Quick Reference Guide FOR VT 9161 SELECT CID PHONE FLASH HOLD OFF 1 4 GHI 7PQRS TONE 2 ABC 5 JKL 8 TUV 0 OPER PROG CHAN 3 DEF 6 MNO 9WXYZ 900 VT 9161 MH z WER ANS F ON /OF REC /ME MO MEM NEW REDIAL PAUSE MES CA LL SAG E NEW E MA ILBO X 3 /CH IN USE ARG MA ILBO X X 2 MA ILBO 1 OP /ST PLAY MEN U TIM DEL ETE E/SE T SEL ECT VOL SKIP /QU ICK REP EAT /SLO W PAG E MIC VTECH COMMUNICATIONS LTD. VTECH COMMUNICATIONS LTD. 1. POWER UP: ANSWER ON/OFF LED illuminates at power up 2. ITAD Programing Overview 1.Set Outgoing Message. 2.Set Security Code 900MHz VT 9161 REC/MEMO ANSWER ON/OFF MESSAGE NEW CALL IN USE/CHARGE MAILBOX MAILBOX MAILBOX 3 1 2 PLAY/STOP DELETE TIME/SET SELECT MENU REPEAT/SLOW SKIP/QUICK VOL PAGE ANSWER ON/OFF REC/MEMO DELETE TIME/SET SELECT MENU SKIP/QUICK REPEAT/ SLOW PAGE 3.Set Day and Time 4.Set Audible Message Alert 5.Set Announce Only 6.Set Base Ringer 7. Set Number of Rings TELEPHONE WALL JACK MIC AC ELECTRICAL OUTLET RECORDING OUTGOING ANNOUNCEMENTS 1. Press MENU ( "--" LED flashes during set-up). Prompt : "Set Outgoing Message ". 2. Press REC/MEMO to record announcement. Prompt: "Now Recording ". Record your announcement. 3. Press MAILBOX X(1,2 or 3) to stop recording. Your announcement will automatically be played back, followed by a beep. SET SECURITY CODE 1. Press MENU twice. Prompt: "Set Security Code" (default setting is 19). 2. Press SELECT. Prompt will give current security code. Continue to press SELECT until desired security code is reached (00-99). Short press increase code by 1. Holding SELECT continuously will increment code by 10. 3. Press TIME/SET. Prompt: "Security Code is XX". SET DAY & TIME 1. Press MENU 3 times. Prompt: "Set Day & Time". 2. Press SELECT. Voice cycles through days of the week as you keep pressing SELECT. Stop at desired day. 3. Press TIME/SET. Voice cycles through the hours as you keep pressingSELECT. Stop at desired hour. 4. Press TIME/SET. Voice cycles through the minutes as you keep pressing SELECT. Stop at desired minute.NOTE: holding SELECT key continuously increases minutes by 10. 5. Press TIME/SET. Voice will repeat the selected DAY & TIME. SET AUDIBLE MESSAGE ALERT 1. Press MENU 4 times Prompt: "Set Audible Message Alert ". 2. Press SELECT. Prompt: "ON " (or "OFF" ). 3. Pressing SELECT toggles between ON and OFF. 4. Press TIME/SET. Prompt: "Audible message Alert ON" (or "OFF"). SET ANNOUNCE ONLY 1. Press MENU 5 times. Prompt: "Set Announce Only". 2. Press SELECT until desired setting "on" or "off" is declared. 3. Press TIME/SET. Prompt: "Announce Only" is ON (or OFF). SET BASE RINGER 1. Press MENU 6 times. Prompt: "Set Base Ringer". 2. Press SELECT. Prompt: "ON" (or "OFF"). 3. Press SELECT to toggle between ON and OFF. 4. Press TIME/SET. Prompt: "Base Ringer is on (or off)". SET # OF RINGS 1. Press MENU 7 times. Prompt: "Set Number of Rings ". 2. Press SELECT. Voice cycles through "2, 4, 6, Toll Saver ". Press SELECT until you reach desired setting. 3. Press TIME/SET. Voice will repeat selected Ring setting. Press any MAIL BOX key to exit set-up mode at any time. ...