Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. 2. 3. 4. 5. 6. Read and understand all instructions. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool). Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage. Slots and openings in the Handset and Base Unit are provided for ventilation. To protect it from overheating, these openings must not be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation where proper ventilation is not provided. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. Do not allow anything to rest on the power cord. Do not install this product where the cord might be damaged by anyone walking on it. Never push objects of any kind into this product through holes and slots in the Handset and Base Unit as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently used. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 7. 8. 9. 10. 11. 1 Important Safety Instructions 12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage and will often require extensive work by an authorized technician to restore the product to normal operation. E. If the product has been dropped and the cabinet has been damaged. F. If the product exhibits a distinct change in performance. 13. 14. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. SAVE THESE INSTRUCTIONS 2 Introduction The 2655 is an advanced cordless telephone that operates in the 2.4 GHz frequency range. This manual is designed to familiarize you with the 2655 cordless telephone. IMPORTANT Please record the Base ID code (BS ID) printed on the underside of the 2655 Base in the space below. Please be certain to include all 15 digits/ characters. Base ID# 3 Parts Check List 1. 2. 3. 4. Base Unit Handset AC Power Adapter Telephone Cord 5. 6. 7. Battery Pack Belt Clip User's Manual Base Unit Handset Battery Pack Telephone Cord Belt Clip AC Power Adapter 4 The Handset Layout 1 2 3 9 4 5 6 7 10 11 8 12 13 14 1. 2. 3. 4. 5. 6. 7. 8. Antenna Message Waiting Indicator Earpiece Headset Jack (2.5mm) Scroll Keys On/Flash Dialing Key (0 - 9, *, #) Handsfree Speakerphone 9. LCD Display 10. Select 11. Off/Clear 12. Intercom 13. Billed Services 14. Microphone 5 Dialing Keys (0 - 9, *, #) AC Power Jack Phone Cord Jack MODEL : 2652 HAC FCC ID: EW780-5001-00 MANUFACTURED IN CHINA COMPLIES WTH 47 CFR PART 68 REGISTRATION NO.: EW7 CHN-34723-WI-E RINGER EQUIVALENCE: 0.0B USOC JACK: RJ11C/RJ11W THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. Auto Callback Key 3-Way Calling Key Repeat Dialling Key Voicemail Key Charging Contacts Erase Key Skip Key Redial Key Flash Key Hold Key Page Key Charge Indicator Power Indicator In Use Indicator Volume Keys Speaker Key Mute Key Play Key The Base Unit Layout 6 Setup Plug the AC power adapter into an electrical outlet, and the DC connector into the back of the Base Unit. To AC outlet To telephone socket outlet To AC power jack To telephone jack Connecting to phone line Plug one end of the telephone line cord into the jack on the back of the Base Unit. Plug the other end of this cord into the wall jack. Checking for dial tone After the battery is charged press ON on the Handset. The Phone icon will appear on the Handset display, and you will hear dial tone. If not, see In Case of Difficulty. Tone/Pulse selection See BASE SETTINGS for details. CAUTION: Use only the power supply provided with your 2655 Unit. IMPORTANT: For best performance the 2655 should be installed as follows: In an elevated location, in the center of the room, with no obstructions nearby. In a location that is away from other electrical appliances such as microwave ovens, personal computers, or televisions. 7 MODEL : 2652 HAC FCC ID: EW780-5001-00 MANUFACTURED IN CHINA COMPLIES WTH 47 CFR PART 68 REGISTRATION NO.: EW7 CHN-34723-WI-E RINGER EQUIVALENCE: 0.0B USOC JACK: RJ11C/RJ11W THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. Getting Started Getting Started Installation of Battery Pack in Handset Follow the steps below: 1. Remove battery compartment cover by pressing on the indent and sliding downward. 2. Place the new battery pack in the Handset with the metal contacts aligned with the charge contacts in the battery compartment. Replace the battery compartment cover by sliding it upwards. If the new battery pack is not already charged, place the Handset in the Base Unit, or a charging stand, and allow it to charge for 10-12 hours. After initial charge, a maintenance charge of 8 hours should be sufficient. 3. 4. 8 Spare Battery Charger/Power Backup Function The 2655 can use the spare battery in the Base Unit to provide operational backup in the event of a power failure. With a fully charged battery pack in the spare battery charger, you will still be able to place and receive calls from the Handset for up to 3 hours. The spare battery pack can also be used to replace a drained Handset battery, ensuring uninterrupted use. A spare battery can be purchased from most retail stores that carry electronic equipment. NOTE: When using the 2655 during Power Backup mode, audio quality may be compromised due to reduced Power availability. The Base Unit can't be used when in power backup mode. 1. Open the spare battery charger by pressing the release button, located on the right-hand side of the Base Unit. A drawer will open to reveal the spare battery compartment. MODEL : 2652 HAC FCC ID: EW780-5001-00 MANUFACTURED IN CHINA COMPLIES WTH 47 CFR PART 68 REGISTRATION NO.: EW7 CHN-34723-WI-E RINGER EQUIVALENCE: 0.0B USOC JACK: RJ11C/RJ11W THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. 2. 1 Place a battery pack in the drawer with the charge contacts facing up and to the left. Push the drawer closed. 3. The spare battery takes 24 hours to fully charge a drained battery. BATTERY INSTALL THIS SIDE UP CAUTION: TO REDUCE RISK OF FIRE, USE ONLY VTECH 80-5017-00-00 3 2 BATTERY INSTALL THIS SIDE UP CAUTION: TO REDUCE RISK OF FIRE, USE ONLY VTECH 80-5017-00-00 9 Getting Started Getting Started Charging Of Handset Battery Pack The Handset of your 2655 cordless telephone is powered by a rechargeable battery pack. It charges automatically whenever the Handset is in the Base Unit. You should charge the battery pack for 12 hours when you first receive your phone. You'll know the battery pack needs charging when: · The low battery message is displayed: The Handset seems completely dead, the LCD is completely clear and does not activate when you press the keys. · CAUTION: to reduce the risk of fire or injury to persons by battery, read and follow these instructions. 1. Use only the appropriate type and size battery pack specified in the instruction manual provided for this product. Do not dispose of the battery pack in a fire. The cell may explode. Check with State and local codes for possible special disposal instructions. Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. Exercise care in handling battery in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns. Charge the battery pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in theinstruction manual. Observe proper polarity orientation between the battery pack and battery charger. 2. 3. 4. 5. 6. 10 Handset and Base Indicators Handset Icons Icon Description Line In Use indicator On steady with no number next to it when a parallel set is in use. On steady with one or more numbers next to it, indicating which extensions are using the line. For example, 12 indicates that Handset 1 and Handset 2 are on an outside call. Intercom indicator On steady with the extension numbers currently on an intercom call. For example, 02 indicates that the Base and Handset 2 are on an intercom call. Battery indicator Cycles (Low, Medium, and High) when Handset battery is charging. Flashes when a low battery condition is detected. M H E Mute indicator On steady when the Handset microphone is muted. Hold indicator On steady when the line is on hold. Range Extender indicator On steady when the Range Extender is on. Handset Registration indicator is displayed when a Handset is either not registered, or is searching for a Base Unit. 11 Basic Operation Handset and Base Indicators Handset LEDs LED Message Waiting Description · Flashes to indicate that you have new messages in your voicemail. Service must be subscribed to through your local telephone company. Basic Operation Base LEDs LED VOICEMAIL Description · Flashes to indicate that you have new messages in your voicemail. Service must be subscribed to through your local telephone company. · Lights when Base unit is receiving power from wall outlet. · Flashes when unit is in Power Backup mode. · Lights when line is being used by any Handset of the 2655 system. · Flashes when another telephone on the same line (parallel extension) is in use. · Flashes following ringing cadence while the phone is ringing. · Lights whenever the Handset is placed in the Base Unit charging cradle. · Flashes briefly when put a spare battery in the spare battery compartment. · Lights when Base microphone is muted. · Flashes when HOLD function is activated. · Lights when Base speaker is in use. Power In Use Charge Mute Speaker 12 Soft Menu Functions The 2655 has an advanced design that uses a menu structure and soft keys to access all of the built-in features. Example of the idle mode display: RDL (Redial) Press RDL to display the last 5 telephone numbers dialed. The number on top line is the most recent number dialed. · · Use the scroll keys to select the desired number. To dial the number, you can simply press the ON or HANDSFREE key. To Save Redial to Memory: Use the scroll keys to select the desired number. Then press SELECT. Press SAVE. Use the steps from 3 to 5 of To Store a Number/Name. To Erase Redial: Use the scroll keys to select the desired number. Then press SELECT. Press ERASE. MENU With the Handset in the idle (OFF) mode, press the MENU key to access the following options: · · · · · · · CALLS LOG ...