User manual WACOM CINTIQ 20WSX

Installation Guide & Hardware Manual for Cintiq 20WSX (DTZ-2000W) Wacom Cintiq® 20WSX Installation Guide & Hardware Manual for Cintiq 20WSX (DTZ-2000W) English version 1.0, January 15, 2007 Copyright Wacom Company, Limited, 2007 All rights reserved. No part of this manual may be reproduced except for your express personal use. Wacom reserves the right to revise this publication without obligation to provide notification of such changes. Wacom does its best to provide current and accurate information in this manual. However, Wacom reserves the right to change any specifications and product configurations at its discretion, without prior notice and without obligation to include such changes in this manual. DuoSwitch is a trademark, and Cintiq and Wacom are registered trademarks of Wacom Company, Limited. Photoshop is either a registered trademark or a trademark of Adobe Systems Incorporated in the United States and/or other countries. Microsoft, Windows, and Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Apple, the Apple logo, and Macintosh are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. Any additional company and product names mentioned in this documentation may be trademarked and/or registered as trademarks. Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. Wacom assumes no responsibility with regard to the performance or use of these products. ExpressKey is a registered trademark of Ginsan Industries, Inc., and is used with permission. INTRODUCTION AND OVERVIEW The Wacom® Cintiq® 20WSX pen display combines the benefits of an LCD monitor with the control, comfort, and productivity of Wacom's cordless, battery-free pen technology. This gives you a direct pen-on-screen interface that can be used with a Personal Computer (PC) or Macintosh® computer. Cintiq's basic components include a Wacom pen tablet internally mounted behind a 20.1" wide format TFT color LCD monitor, and Wacom's Grip Pen. Cintiq comes with a modular display stand, which allows you to easily rotate the pen display to any orientation, and to adjust the incline of the working surface to any angle between 10 and 65 degrees. Refer to Unpacking your Cintiq on page 7 before setting up the Cintiq stand or unpacking the Cintiq pen display. Please follow all instructions carefully. This manual describes how to install the Cintiq hardware and software. It also describes how to use Cintiq, the Grip Pen, and the modular display stand. The information is common to Windows and Macintosh computers, and Windows screen captures are shown unless otherwise noted. Note that the computer treats the Cintiq pen display as two separate devices (the LCD monitor and the pen tablet). Therefore, the installation process is completed in two stages: · First install the Cintiq as a display. · Then install the Cintiq as a pen tablet. Both stages require hardware and software installations and adjustments. Please follow all instructions carefully. IMPORTANT: You MUST install the Wacom pen tablet driver software for full pen and tablet functionality, otherwise the Cintiq pen will only function as a mouse device and the extended pen and tablet features will not be available. The following kinds of information are not included with this product: information about your specific computer hardware or operating system, or information about your application software. Your best source for this information is the set of manuals and disks that came with your hardware, operating system, or application. For information on using the Wacom Tablet control panel to customize your pen display tablet and pen settings, refer to Customizing on page 32 and to the electronic Software User's Manual. See also Learning more about Cintiq on page 35. To use the pressure-sensitivity of the Grip Pen with your favorite drawing application, refer to instructions in that application's manuals. Introduction and overview Page 1 PRECAUTIONS ON USE AND HANDLING Be sure to follow all instructions, cautions, and warnings found within this manual. Failure to do so could cause the loss of data or damage to your computer. Failure to do so could also void your warranty, in which case Wacom shall have no responsibility to repair or replace the product. Physical location WARNING Do not use the Cintiq pen display in a facility control system that requires extremely high reliability; it may cause other electronic devices to malfunction, or other devices may cause the pen display tablet to malfunction. Where use is prohibited, power off Cintiq to prevent the possibility of it causing other electronic devices to malfunction. Wacom does not accept any liability for direct or consequential damages. For details, please refer to your Warranty located at the end of this manual. Environment Temperature and Humidity · Operating temperature and humidity: 5° to 35°C, 20 to 80% RH · Storage temperature and humidity: -10° to 60°C, 20 to 90% RH CAUTION Do not use or store Cintiq where: · Temperature changes are severe or exceed specifications (e.g., outdoors or inside a vehicle). · The pen display, the Grip Pen, and the Cintiq stand are exposed to direct sunlight or heat from an appliance, or are exposed to water or any other kind of liquid. Do not use Cintiq in a dusty environment; this may damage the unit. CAUTION Usage WARNING Only use the power adapter that came with Cintiq. If a different type of power adapter is used, Cintiq will not work properly or may be damaged. Using a different type of power adapter also has the potential to result in fire. Use of a different power adapter will void your warranty. Be sure to use a grounded power source when applying power to Cintiq. Do not connect or disconnect the video or power cables while Cintiq or your computer are turned on; this may damage the LCD monitor or computer video card. In this case, Wacom shall have no responsibility to repair or replace the product. This product is for use with a DVI or VGA video card; using an inappropriate video card may damage Cintiq. Do not block the rear panel ventilation holes; this may overheat and damage the unit. When not using Cintiq for long periods of time, unplug the power adapter from the AC outlet. CAUTION CAUTION CAUTION CAUTION Precautions on use and handling Page 2 Handling WARNING High Voltage. Do not open or disassemble the Cintiq pen display. There is a risk of electrical shock when the casing is open. This will also void your warranty and Wacom shall have no responsibility to repair or replace the product. Do not operate the display stand incline adjustment levers when Cintiq is not mounted on the stand, and do not lift the stand by the adjustment levers; the stand is springloaded and may cause injury or damage if released without the weight of Cintiq on the stand. Improper operation may lead to physical injury or damage to the stand. When moving Cintiq to a different location, either remove the display unit from the stand (see page 12 for details) and then move both items separately, use the lock screws to fix Cintiq to the stand (see page 56 for details), or hold onto both Cintiq and the stand to make sure that the stand does not separate from the display unit when moving them together. Before moving Cintiq, first adjust the stand to its full upright position; this will reduce the spring tension so that the stand will not accidentally release and snap shut. If the display unit is in landscape orientation, use one hand to grasp the bottom of the display and with your other hand grasp the back of the stand. Be sure to lift on both the display and the stand so that the stand will not separate from the display when moving Cintiq. If Cintiq is in portrait orientation or has been locked to the stand with the rotation lock screws (see page 56), the stand will not separate from the display unit and Cintiq can be safely lifted by grasping the display unit with both hands. Always follow the instructions on page 12 to remove the display unit from the stand. If the LCD screen has been damaged, DO NOT touch any liquid that may be leaking from it; this liquid is an irritant. In case of contact with skin, eyes, or mouth, rinse immediately with running water for at least 15 minutes or more. If contact is made with the eyes or mouth, also consult a physician. WARNING WARNING WARNING WARNING ­ LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. The Cintiq pen display has a backlight which contains mercury (Hg). Be sure to dispose of properly, and to manage any disposal of this unit in accordance with your local ordinances and laws. WARNING Do not disassemble the Cintiq stand. Improper disassembly could result in physical injury or damage to the stand. In this case, Wacom shall have no responsibility to repair or replace the product. Prevent children from swallowing the pen tip or side switch. The pen tip or side switch may accidentally be pulled out if children are biting on them. Do not disassemble the Grip Pen. This may cause the device to malfunction. In this case, Wacom shall have no responsibility to repair or replace the product. Do not scratch the display screen. Avoid placing sharp objects on the display screen surface. Avoid intensive shock or vibration to Cintiq, the Cintiq stand, or the Grip Pen. Hitting or dropping Cintiq may damage the display screen or other components. Hg WARNING CAUTION CAUTION CAUTION Precautions on use and handling Page 3 CAUTION CAUTION CAUTION CAUTION CAUTION Do not put heavy articles on the pen display or push against it with a strong force; this may damage the display screen or break the Cintiq stand locking mechanism. Do not place heavy articles on the Cintiq cabling, repeatedly bend the cables sharply, or apply heavy stress to the cable connectors; this may damage the unit or cabling. Do not store the pen display tablet on a surface that would excessively bend or crimp the cable. If the pen tip becomes sharp or angular, it may damage the coating on the display screen. Please replace the pen tip if necessary. Do not use any organic solvent (e.g., alcohol) or even mild detergent to clean the display screen. Use of these cleaners can damage the coating on the screen. Please note that damage of this kind is not covered by the manufacturer's warranty. · To clean the display screen, use an anti-static cloth or a slightly damp cloth. When cleaning, apply only a light amount of pressure to the display screen and do not make the surface wet. · To clean the Cintiq casing, Cintiq stand, or Grip Pen, use a soft cloth with mild detergent (such as dish washing liquid) diluted with water. Do not expose Cintiq to high voltage electrostatic discharges or to a build-up of an electrostatic charge on the LCD screen. This may result in a temporary discoloration and blotching of the LCD monitor. If discolorations occur, leave Cintiq's display on and the discolorations should disappear within a few hours. Reuse, recycling, and recovery. You are urged to recycle this product when replacing it with a newer product or when it has outlived its useful life by bringing it to an appropriate collection point for recyclable materials in your community or region. By doing this, you can help improve the environment of your community as well as minimize the potential negative effects created should any hazardous substance that may possibly be present within waste material reach the environment during the disposal process. Within the European Union, users are required not to dispose of Waste Electrical and Electronic Equipment (WEEE) as unsorted municipal waste, according to the Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003, or the corresponding local laws of the Member States. Products for which this is applicable will be marked with the WEEE symbol shown at the beginning of this note unless this is not feasible because of the size or the function of the product. Wacom products are subject to the Directive 2002/96/EC and therefore you should always collect them separately and bring them to the appropriate collection point in your community or region. Wacom pen display products (Cintiq series) comply with the European Union RoHS Directive 2002/95/EC (RoHS Directive). CAUTION Precautions on use and handling Page 4 CONTENTS Introduction and overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Precautions on use and handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Physical location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking your Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Setting up the Cintiq stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Unpacking and mounting the Cintiq pen display . . . . . . . . . . . . . . . . 9 Cintiq pen display components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Step 1: LCD monitor installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Step 2: Pen tablet installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Working with your Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Using the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Working with the tablet controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Setting up your work area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Customizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Opening the control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Customization basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Adjusting the LCD monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Testing Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Testing your input tools and pen display controls . . . . . . . . . . . . . . 43 Display troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Pen tablet troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Technical support options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Obtaining driver downloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Contents Page 5 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Caring for Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optional display configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . Using an alternate mount or stand . . . . . . . . . . . . . . . . . . . . . . . . . Pen and digital ink capabilities in Windows Vista . . . . . . . . . . . . . . Uninstalling Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Purchasing parts and accessories . . . . . . . . . . . . . . . . . . . . . . . . . Radio and television interference . . . . . . . . . . . . . . . . . . . . . . . . . . Warranty (Worldwide, Except for Europe, Africa and Middle East) . . . . . . . . 54 54 56 57 60 61 62 65 66 67 Contents Page 6 UNPACKING YOUR CINTIQ Package contents You will find parts and accessories packed together in the accessories box. To avoid damaging your product, please review the instructions on the following pages before setting up or using Cintiq or the Cintiq stand. Your product came with the following items: Cintiq stand (MST-A103) *Patented Cintiq 20WSX (model DTZ-2000W) pen display, main unit with attached cable Parts and accessories Rotation lock screws (qty 2) (MNE-A067) Grip Pen with replacement nibs, pen stand, and nib removal set (ZP-501E, PST-A034, and FUZ-A131) Bearing hub recess cover plate and screws (PPL-A155 and NEM-A068) VGA to DVI-I adapter (STJ-A252) Installation Guide & Hardware Manual (this manual) DVI-D to DVI-I adapter (STJ-A253) Wacom Pen Tablet Driver CD (contains the driver software) Power supply (POW-A100) and power cable Notes: Images are not shown to scale. Some package configurations may include additional CDs or DVDs containing application software. To install these applications, review the instructions that came with those CDs or DVDs. Retain the package box for use when storing or shipping Cintiq. Next step: Set up the Cintiq stand. See page 8. Unpacking your Cintiq Page 7 Setting up the Cintiq stand Place the stand on your desktop or work surface, making sure the stand is stable and will not tip or fall when the pen display is mounted on it. Then familiarize yourself with the stand components. WARNING Do not operate the incline adjustment levers when Cintiq is not mounted on the stand, and do not lift the stand by the adjustment levers; the stand is spring-loaded and may cause injury or damage if released without the weight of Cintiq on the stand. Improper operation may lead to physical injury or damage to the stand. Be careful to avoid catching your finger in the gap of the movable portion of the stand. Incline adjustment levers When Cintiq is mounted on the stand, use these levers to adjust the display incline, as described in Adjusting the display incline on page 10. Bearing recess Front feet The front feet have rubber pads to reduce stand slippage on the desktop when adjusting incline. Rear feet The rear feet are on rollers, allowing the feet to move when adjusting incline. Next step: Unpack the pen display and mount it on the Cintiq stand. See page 9. Unpacking your Cintiq Page 8 Unpacking and mounting the Cintiq pen display Remove any packing materials from the back of the display unit and cabling. To mount Cintiq on the stand: · Make sure the stand is stable on your desktop or other work surface and will not tip or fall when Cintiq is mounted on it. · Securely grasp Cintiq with both hands so that the display faces toward you, with the power switch and LEDs located at the top. · Align Cintiq parallel to the front of the stand so that the bearing hub is located between the V-shaped upper edges of the stand's bearing recess. See ­ A ­ (The V-shaped edges of the stand will serve as a guide for positioning the bearing hub.) · With the back of Cintiq resting against the stand, lower Cintiq until the bearing hub rests securely in the bearing recess of the stand. See ­ B ­ on the next page. The display unit will be held in place by gravity; there will be no audible `snap' that indicates a mechanical lock. Note: If you do not need to rotate the Cintiq pen display, you may want to secure it to the stand with the rotation lock screws. For information on this, see Optional display configurations on page 56. To learn about other mounting options, see Using an alternate mount or stand on page 57. ­A­ Bearing hub Bearing recess Unpacking your Cintiq Page 9 WARNING When operating the incline adjustment levers, Cintiq must be mounted on the stand with the stand feet resting on a stable, flat surface. The stand is spring-loaded and can snap back quickly, causing injury or damage if not operated properly. ­B­ After the display unit has been mounted on the stand, remove the foam blocks that lock the adjustment levers in place. Save these blocks with the other packaging materials; you will need them if in the future you want to ship Cintiq. Adjusting the display incline To adjust the display incline, face the front of the Cintiq pen display and grasp it on the left and right side at approximately the same height as the Cintiq stand adjustment levers. Use your fingertips to gently pull the incline adjustment levers toward the display unit; this will release the stand's clutch mechanism. Tilt the display to adjust the incline setting. · To lower Cintiq, pull the left incline adjustment lever toward Cintiq and gently lower Cintiq to the desired incline angle. Release the lever to lock the stand in place. · To raise Cintiq, pull the right incline adjustment lever toward Cintiq and gently raise Cintiq to the desired incline angle. Release the lever to lock the stand in place. Note: The stand adjustment levers exhibit some natural play before the clutch mechanism engages. When adjusting the stand incline, set it slightly higher than you plan to work with, then lower the display to the desired position. WARNING Before moving Cintiq, first adjust the stand to its full upright position; this will reduce the spring tension so that the stand will not accidentally release and snap shut. If the display unit is in landscape orientation, use one hand to grasp the bottom of the display and with your other hand grasp the back of the stand. Be sure to lift on both the display and the stand so that the stand will not separate from the display when moving Cintiq. If Cintiq is in portrait orientation or has been locked to the stand with the rotation lock screws (see page 56), the stand will not separate from the display unit and Cintiq can be safely lifted by grasping the display unit with both hands. Unpacking your Cintiq Page 10 Adjusting rotation The pen display can be rotated on the display stand when the incline is less than or equal to 25 degrees. To adjust rotation, grasp Cintiq by the main body and rotate the unit to the desired position; it will move on the bearing hub. You can only rotate the display unit 180 degrees in either direction. If you do not plan to rotate the Cintiq, use the rotation lock screws to fasten the display to the stand in a horizontal position. See Optional display configurations on page 56 for more information. Using the pen holder The integrated pen holder is located at the back of the pen display tablet. Note: The pen holder is not available for use when routing the cable to exit through the top cable opening. Next step: Go to page 13 and familiarize yourself with the pen display. Unpacking your Cintiq Page 11 Removing Cintiq from the display stand To remove Cintiq from the display stand: · If the rotation lock screws are attached, remove them from the back of Cintiq. · Position the pen display to landscape orientation before removing it from the display stand. The stand will not release unless Cintiq is in landscape orientation. · Next, raise the stand incline to the highest position. See Adjusting the display incline on page 10 for instructions. · Firmly grasp the pen display on both the left and right sides of the body, and lift the unit out of the display stand. Important: When removing Cintiq from the display stand, always lift Cintiq in a direction parallel to the front of the stand. You may also need to rotate Cintiq slightly so the stand will release. Note: When packing Cintiq for transport, first adjust the stand to its lowest position and place the foam packing blocks under the incline adjustment levers before removing Cintiq from the stand. The foam blocks will keep the stand from snapping shut while in its packaging. Always pack Cintiq and its stand in their original containers and protective cushions. Never pack Cintiq while it is mounted on the stand; this may damage the unit or stand during transportation. Unpacking your Cintiq Page 12 CINTIQ PEN DISPLAY COMPONENTS After the Cintiq pen display is safely mounted on the Cintiq stand, take some time to familiarize yourself with its features and components. The LCD monitor and tablet sensor function as an integrated input and output device. The LCD monitor supports resolutions up to 1680 x 1050 pixels at 16.7 million colors. The tablet sensor reports pen coordinates, pressure, tilt, switch, eraser, and other information. Front view Status LED Lights blue when the pen is in the active area of the pen display tablet and the pen tip, eraser, or side switch are pressed. Note that the USB cable connector must be plugged into an active USB port and a video signal must be present before the LED will light. Power switch Turns power to the unit on or off. Power LED Lights blue when power has been supplied to Cintiq and a video signal is present. Glows orange when no video signal is detected by Cintiq. (e.g., Your computer is turned off, starting up, or has entered a power management mode in which video signals are not sent.) ExpressKeys By default, the upper ExpressKeys on each side of the pen display support a TOUCH STRIP MODIFIER function not available to the lower ExpressKeys. ExpressKeys All ExpressKeys can be customized to simulate modifier keys, keystrokes, and other frequently used functions. A display toggle function is also available, enabling you to toggle the screen cursor between the Cintiq pen display and your other displays. See Working with the tablet controls on page 25. Integrated LCD monitor and tablet Cintiq pen display components Page 13 Rear view On Screen Display (OSD) controls These controls enable you to adjust a variety of display settings. See Adjusting the LCD monitor on page 36 for more information. Integrated pen holder and alternate cable exit The pen can be stored here. If you are not using the Cintiq stand supplied with the unit, you can route the cable to exit from this location. See Using an alternate mount or stand on page 57. Digital/Analog (DVI/VGA) switch Set this switch for the video connection you will be using. Touch Strip Kensington security slot Allows easy attachment of a security cable. Pen tether attachment point If you will be using a pen tether, connect it to the attachment point located on either side of the unit. Bearing hub Fits into the bearing recess on the Cintiq stand. Allows rotation of Cintiq, and easy mounting and removal from the stand. Touch Strip Slide your finger over the Touch Strips to zoom, scroll, or perform custom keystroke actions. See Working with the tablet controls on page 25. Cabling and connectors The connectors on the integrated cable are for DVI-I video, USB data, and power. Important: Always store the pen display on the Cintiq display stand or in its original packing carton when not in use. Do not store the display unit on a surface that would excessively bend or crimp the cable. Next step: Installation. See page 15. Cintiq pen display components Page 14 INSTALLATION System requirements Before installing Cintiq, make sure your computer meets the following minimum system requirements: · PC. Windows VistaTM, Vista x64, XP, XP x64, or 2000. DVI or VGA video connector, available USB port, and CD-ROM drive. · Macintosh. OS X, v10.3.9 or greater. DVI or VGA video connector, available USB port, and CD-ROM drive. ADC connectors require an ADC to DVI-I adapter, not included. (ADC to DVI-I adapters can be purchased at various retail outlets.) Cintiq supports both digital (DVI) and analog (VGA) video signals. If you are updating your video card, complete the video card hardware and software installation before connecting Cintiq. If you have another display that is compatible with your video card, you can connect that display to the card in order to verify the video card is operating correctly. Note: Cintiq can be used alone or with another display, such as a CRT monitor or LCD projector. To use Cintiq with another display, you will need two video cards or a video card with dual output. Depending on the capabilities of your video card and operating system, you may be able to set up Cintiq as a mirrored, extended, or independent display. Refer to your video card documentation for more information on its capabilities. When you are working with more than one monitor, Cintiq will map to the monitors based upon how your system is configured. By default, if you are in mirror mode, the pen tablet will map to the entire space on each display or monitor. Please refer to your hardware and operating system documentation for details on configuring your computer and operating system for use with multiple monitors. A display toggle function is available for use with multiple monitor systems. This enables you to toggle the screen cursor between the Cintiq pen display and your other displays. See Using the ExpressKeys on page 26 for more information. By using the VGA to DVI-I adapter, you can connect Cintiq to a VGA video card. However, connecting Cintiq to a DVI video card generally results in optimum performance because a digital video signal will display a better image and sharper text. There are two primary steps to the installation process: · Step 1: LCD monitor installation · Step 2: Pen tablet installation Be sure to follow ALL installation instructions carefully. Installation Page 15 Step 1: LCD monitor installation In the first stage of the installation process, Cintiq is installed as a monitor on your system. As you work through the first stage of the installation process, please refer to the LCD monitor cabling diagram on page 18 when making cable connections. Important: Do not connect the USB data cable until instructed to do so. · Turn off your computer. Caution: Never connect or disconnect the video or power cables while your computer or Cintiq are powered on ­ this can damage the LCD monitor or video card. If your computer has only one video connector, you will need to unplug your previous monitor. Determine if your computer has a digital (DVI-I or DVI-D) or analog (VGA) connector, and set the DIGITAL/ANALOG (DVI/VGA) switch located on the back of Cintiq for the video connection you are using. Move the switch toward the tablet edge for Digital (DVI-I or DVI-D), and move it toward the OSD buttons for ANALOG (VGA). See ­ A ­ in the connection diagram on page 18. Follow the instructions below for your video connector. See ­ B ­ in the diagram on page 18. If you are connecting to a DVI-I connector, plug the Cintiq video cable into the DVI-I connector of your video card. DVI-I connector · · If you are connecting to a DVI-D connector, plug the Cintiq video cable into the DVI-D to DVI-I adapter supplied with Cintiq, and then plug the adapter into the DVI-D connector on your video card. DVI-D connector If you are connecting to a VGA connector, plug the Cintiq video cable into the VGA to DVI-I adapter supplied with Cintiq, and then plug the adapter into the VGA connector on your video card. VGA connector Installation Page 16 If you are connecting to an Apple computer with one of the following video ports, you will need to use an adapter: If you are connecting to an ADC connector, you will need to obtain an ADC to DVI-I adapter. Plug the Cintiq video cable into the ADC to DVI-I adapter. Then plug the ADC adapter end into the ADC connector on your video card. If you are connecting to an Apple mini-VGA connector, you will need to obtain a mini-VGA to VGA adapter. Plug the Cintiq video cable into the VGA to DVI-I adapter (supplied with Cintiq). Plug the mini-VGA adapter into the computer's mini-VGA port. Then plug the male and female VGA connectors together. Apple ADC connector Mini-VGA port · · These adapters can be purchased at various retail outlets. Be sure to tighten the thumbscrews on the connectors. Connect the power adapter to Cintiq. See ­ C ­ on the next page. Then connect the adapter's power cable and plug the adapter into an AC outlet. See ­ D ­ Installation Page 17 LCD monitor cabling diagram ­A­ DIGITAL/ANALOG (DVI/VGA) switch CAUTION Make sure your video card has a DVI or VGA connector, and that you correctly set the Cintiq Digital/Analog (DVI/VGA) switch for the video connector you are using. Do not attach the USB data cable until instructed to do so. Cintiq, rear view ­B­ ­C­ DC INput Video card DVI or VGA DVI-I connector To connect to a DVI-D connector, use the DVI-D to DVI-I adapter cable. To connect to a VGA connector, use the VGA to DVI-I adapter cable. Rear panel of your computer ­D­ Power adapter To AC outlet CAUTION Use only the power adapter that came with Cintiq; use of an improper power adapter may damage the unit. Do not connect or disconnect the video or power cables while Cintiq or your computer are turned on ­ this can damage the LCD monitor or computer video card. Make sure that the display refresh rate does not exceed 75 Hz (60 Hz for WSXGA). Installation Page 18 · · Turn on Cintiq. The power LED will light orange. Next, turn on your computer. For Windows systems, Cintiq will automatically install as a default monitor. If you want Cintiq to be identified as a Cintiq display and if you want to install the color calibration profile for Cintiq, follow the instructions below to update the display driver for Cintiq: 1. From the CONTROL PANEL folder, open the DISPLAY PROPERTIES control panel. · For Windows Vista, select ADJUST SCREEN RESOLUTION. · For other Windows versions, select the SETTINGS tab. Click the IDENTIFY button if you need help in determining which display corresponds to Cintiq. If you have more than one display, select the display for Cintiq then click the ADVANCED button. 2. Select the MONITOR tab and click the PROPERTIES button. 3. Select the DRIVER tab and click the UPDATE DRIVER button. The HARDWARE UPDATE WIZARD will display. 4. Insert the Wacom Pen Tablet Driver CD. If the Wacom Tablet installation menu displays, close it. Windows Vista: · Select the option BROWSE MY COMPUTER FOR DRIVER SOFTWARE. · Enter the drive letter for the Wacom Pen Tablet Driver CD and click NEXT. · After the installation is complete, close the DISPLAY PROPERTIES control panel. Windows XP: · If the driver was not found, click the BACK button, then select the option INSTALL FROM A LIST OR SPECIFIC LOCATION (ADVANCED), and click NEXT. · Select the option DON'T SEARCH. I WILL CHOOSE THE DRIVER TO INSTALL and click NEXT. · Click the HAVE DISK button, enter the letter of your CD-ROM drive (e.g., E:\), and click OK. · If the HARDWARE INSTALLATION dialog box displays, click CONTINUE ANYWAY to accept the driver. After the installation is complete, click the FINISH button to close the Wizard and then close the DISPLAY PROPERTIES control panel. Windows 2000: · Follow the prompts selecting the default options. · If a signing warning dialog box displays, click YES to accept the driver. After the installation is complete click the FINISH button to close the Wizard and then close the DISPLAY PROPERTIES control panel. For Macintosh systems, a Cintiq color profile will be added to your computer's color management system during the tablet software driver installation process. To activate this color profile for use with Cintiq, you may need to select the Cintiq 20WSX profile in the system's ColorSync Utility control panel. For more details, refer to the color management information in your operating system and application documentation. Installation Page 19 · · · As necessary, configure the display control panel settings for the proper size and color resolution. The maximum (native) resolution of the Cintiq 20WSX is 1680 x 1050 pixels with 24 bit color (8 bits per color). The display size and color resolution may be constrained by the capabilities of your video card. See the video card manufacturer's documentation for details. If you are using analog (VGA) mode, you may want to fine-tune the display. Please refer to Adjusting pitch and phase (VGA only) on page 39, and to Adjusting the LCD monitor beginning on page 36 for more information. For Windows: If you are using Cintiq as a secondary display, you may first need to enable Cintiq in your Display Properties control panel. After the LCD monitor portion of Cintiq is working to your satisfaction, move on to Step 2: Pen tablet installation to install the pen tablet portion of Cintiq. For troubleshooting tips, please refer to page 41. Notes: Each Cintiq LCD panel is produced under very stringent quality standards. Production techniques cannot guarantee an absolutely perfect TFT display, and some panels may exhibit a certain number of pixels that show an incorrect color. Refer to the specifications on page 62 for more information. If an image has fine striping (such as screen stripes), it may appear to flicker or display a moiré pattern. Do not apply excessive pressure on the display surface, it may cause the appearance of a moiré or pooling pattern. If you notice this action, use less pressure on the display screen when working with the pen. When a still image is displayed for a long period of time, an after-image may remain for a short time. To prevent this, Wacom recommends using a screen saver or other power management feature. Important: To extend the life of the backlight, set your computer's power management to turn off the display when it is not in use for an extended period of time. Installation Page 20 Step 2: Pen tablet installation USB cable installation Plug the USB connector into an available USB port on your computer or into a USB hub attached to your computer. Next, move on to the pen tablet Software installation on page 22. You must install the Wacom tablet driver software for full tablet functionality. Pen tablet cabling diagram To Cintiq To USB port Your computer Installation Page 21 Software installation IMPORTANT: You MUST install the Wacom pen tablet driver software for full pen and tablet functionality, otherwise the Cintiq pen will only function as a mouse device and the extended pen and tablet features will not be available. To install the tablet software: · Save your work and close all open applications before installing the tablet software. Temporarily disable any virus protection programs. · Insert the Wacom Pen Tablet Driver CD into your computer's CD-ROM drive. If the software installer menu does not automatically display, double-click on the INSTALL icon located on the CD. · Click on the INSTALL TABLET link and follow the prompts to install the driver software. · Reactivate your virus protection program. · After the software installation has been completed, make sure you can use your pen on the Cintiq display to move the screen cursor. When you place the pen tip on the display screen, the screen cursor should immediately jump to a corresponding position approximately beneath the pen tip. Lift the pen tip and place it on the display screen surface in a different location ­ the screen cursor should again jump to the new position. This is known as absolute positioning, and enables you to position the screen cursor without having to drag your pen across the display screen surface. To fine-tune the cursor-to-pen relationship, see Calibrating Cintiq on page 34. Be sure to check the Read Me file for late-breaking news. If you have trouble installing Cintiq, see the Troubleshooting section beginning on page 41 of this manual. Notes: · For Windows Vista, driver installation automatically activates the new pen input functions available within Windows Vista and Office 2007 (except for Windows Vista Home Basic). · For Windows Vista and XP, user-specific preferences are supported. After logging in, each user can customize their personal settings in the Wacom Tablet control panel. Switching to another user will automatically load the settings for that user. · The Windows Vista log-in screen does not support screen cursor movement with the pen tablet. Use the arrow keys or a standard mouse to select the user name for logging in. Next steps: Be sure to adjust the pen display tablet calibration to precisely align the screen cursor position with the location of the pen tip. See Calibrating Cintiq on page 34. To learn more about using Cintiq, proceed to Working with your Cintiq on page 23. Installation Page 22 WORKING WITH YOUR CINTIQ Using the pen As you work with Cintiq, you can rest your hand lightly on the display screen, just as if it were a drawing board or sheet of paper. The Grip Pen is cordless, battery-free, and sensitive to the tilt and pressure you exert upon it. Hold the Grip Pen as you would a normal pen or pencil. Make sure the DuoSwitch is in a convenient location where you can toggle it with your thumb or forefinger, but not accidentally press it while drawing. You can tilt the pen in any way that feels most comfortable for drawing. Eraser Note: When the Grip Pen is not in use, place it in the pen stand, the pen holder, or lay it flat on your desk. To maintain the sensitivity of your pen, do not store the pen in a container where it will rest on its tip or eraser. DuoSwitch (side switch) Tip Switch (replaceable nib) Pen components The components of your Cintiq Grip Pen function in the following manner: Pen tip: The pen becomes activated as soon as it is brought within 5 mm (0.2 inch) of the pen display screen. This allows you to position the screen cursor or use the DuoSwitch without touching the pen tip to the display screen. When pressure is applied to the pen tip, the tip switch is turned on and the pen simulates a primary mouse button click. The tip click pressure can be adjusted in the Wacom Tablet control panel. By default, the tip function is set to CLICK. DuoSwitch: The DuoSwitch is programmable, and can be used to perform the same click and doubleclick functions as the tip switch. Toggle the DuoSwitch in either direction to activate the upper or lower button functions. You can use the DuoSwitch whenever the pen tip is within 5 mm (0.2 inch) of the tablet surface; you do not need to touch the pen tip to the tablet in order to use the switch. By default, the upper switch is set to DOUBLE CLICK and the lower switch is set to RIGHT CLICK. Eraser: When the eraser is brought within 5 mm (0.2 inch) of the display the tablet reports the pen location. Pressure information is reported as you press down on the eraser. By default, the eraser function is set to ERASE. Important: Only use a pen that is compatible with Cintiq, such as the pen that shipped with the unit, or any of the pens from the Intuos3 product line (see Accessories on page 64). Other pens may not function properly. Also, the Cintiq pen tip is specifically designed for use with the Cintiq pen display ­ the tips on other pens could damage the protective coating on the Cintiq display screen. Refer to Customizing on page 32 and to the electronic Software User's Manual for information on customizing the pen settings. Working with your Cintiq Page 23 Pen operations The basic methods of working with the pen are as follows: Pointing and selecting: Move the Grip Pen above the Cintiq display screen to position the screen cursor. The pen tip needs to be within 5 mm (0.2 inch) of the pen display tablet surface; you do not need to touch the tablet surface to move the screen cursor. The cursor jumps to the location where you place the pen (absolute positioning). Press the pen tip on the display screen to make a selection. Note: You will need to calibrate the pen display tablet to correctly align the screen cursor with the pen tip. (See Calibrating Cintiq on page 34.) If the screen cursor does not jump to a position close to the pen tip when you place the pen on the display screen, then the pen tablet driver may not be installed or is not loading. Install the pen tablet driver software if necessary. Otherwise, refer to Troubleshooting, beginning on page 41. Clicking: Tap the display screen once with the pen tip, or touch the pen to the display screen with enough pressure to register a click. Windows tip: You can make navigating with the pen easier by configuring Windows to select when the pen is over an icon and to launch the icon with a single click. To turn on this feature first open a folder. For Windows Vista, from the ORGANIZE pull-down menu choose FOLDER AND SEARCH OPTIONS.... From the GENERAL tab select SINGLE-CLICK TO OPEN AN ITEM (POINT TO SELECT). For other Windows versions, from the TOOLS pull-down menu choose FOLDER OPTIONS.... From the GENERAL tab select SINGLE-CLICK TO OPEN AN ITEM (POINT TO SELECT). Double-clicking: Press the upper side switch, or quickly tap the display screen twice in the same place with the pen tip. Double-clicking is easier when the pen is perpendicular to the tablet screen. Refer to the electronic Software User's Manual for information on fine-tuning the double-click area. Dragging: Select an object, then slide the pen tip across the display screen to move the object. Using the side switch: The pen is equipped with a DuoSwitch. This switch has two programmable functions that can be selected by rocking the switch in either direction. You can use the DuoSwitch whenever the pen tip is within 5 mm (0.2 inch) of the tablet surface; you do not need to touch the pen tip to the tablet in order to use the switch. The upper switch is set to DOUBLE CLICK, and the lower switch is set to RIGHT CLICK by default. Drawing with pressure-sensitivity: The pen responds to the nuance and inflection of your hand movements, enabling you to create natural-looking pen and brush strokes within applications that support this feature. To draw with pressure, select a pressure-sensitive tool from your application's tool palette. As you draw on the screen surface, use various amounts of downward pressure on the tip of the pen. Press lightly for thin lines or softer color. Press harder for thick lines or dense color. Drawing with tilt: As with pressure-sensitivity, the pen display tablet recognizes when you tilt the pen from vertical to incline positions. In supporting applications, tilt can be used to control line shape and thickness. Erasing: In supporting applications, the pen's eraser works like the eraser on a pencil. In text applications, use the eraser to select text, then lift the eraser from the tablet to delete the text. Working with your Cintiq Page 24 Working with the tablet controls The customizable ExpressKeys and Touch Strips enable you to speed up your workflow in graphics or other applications. While using the pen with your dominant hand, you can simultaneously use your other hand to operate the ExpressKeys or Touch Strip. For example, use the ExpressKeys to quickly change your tool properties, or slide your finger over the Touch Strip to quickly zoom in or out. ExpressKeys By default, the upper ExpressKeys modify the function of the corresponding Touch Strip located directly behind the keys on the back of the Cintiq pen display. When you press a key that has been assigned to TOUCH STRIP MODIFIER, the Touch Strip function is changed according to the ExpressKeys setting in the Wacom Tablet control panel's TOUCH STRIP tab. See Using the ExpressKeys on page 26 and Using the Touch Strips on page 28. Note that an ExpressKey set for TOUCH STRIP MODIFIER can only change the function of the Touch Strip located on the corresponding side of your Cintiq pen display. ExpressKeys Press the keys to perform frequently used functions or keystrokes. By default, the ExpressKeys emulate keyboard modifier keys. In Photoshop, this provides quick access to the grabber hand and alternate tools. A display toggle function is also available for use on multiple monitor systems. This feature allows you to use your pen on the Cintiq pen display to navigate the screen cursor to any display on your system. See Using the ExpressKeys on page 26. Working with your Cintiq Page 25 Using the ExpressKeys Press the ExpressKeys with your secondary hand to toggle between tools or change tool properties while using your primary hand to work with your pen on the display tablet surface. All ExpressKeys can be customized. The default settings were chosen to optimize your workflow in Photoshop and other graphics applications using the following modifier functions: Button 1: CTRL modifier key for Windows. COMMAND (Apple key) for Macintosh. Button 2: SHIFT modifier key. Button 3: ALT modifier key for Windows. OPTION modifier key for Macintosh. Button 4: SPACE key (spacebar). Button 5: DISPLAY TOGGLE. This option is available for use only on multiple monitor systems. Button 6: Left and right outer TOUCH STRIP MODIFIER. Enables you to change Touch Strip functionality. Button 7: Left and right inner TOUCH STRIP MODIFIER. Enables you to change Touch Strip functionality. By default, the outer ExpressKeys will modify the Touch Strip to adjust the maximum tool size setting in Photoshop. Application-specific settings can be added to customize the keys for working with other applications. 67 76 5 2 1 3 4 3 2 5 1 4 The ExpressKeys are chordable. For example, pressing keys 1 and 3 together simulates CTRL+ALT in Windows, or COMMAND+OPTION on Macintosh systems. Working with your Cintiq Page 26 The ExpressKeys enable you to speed up many common tasks. You can work with the default settings, or choose from any of the other available functions. For example: · Quickly change the functionality of a Touch Strip by first pressing a corresponding ExpressKey that has been customized for the TOUCH STRIP MODIFIER function and then using the Touch Strip. · On multiple monitor systems only, set an ExpressKey or a pen side switch to DISPLAY TOGGLE. You can then press that button to toggle the screen cursor between the Cintiq pen display tablet and your other displays. For example, Cintiq can be used as a pen display where the screen cursor is positioned at the pen tip location, or toggled for use as a standard Wacom tablet where the screen cursor can be moved across the entire desktop or additional displays. · In Photoshop, pressing the spacebar (key 4 on your pen display tablet) switches the currently selected tool to the hand tool and lets you pan (move) the image within the application window. · In Photoshop and many other graphics applications, the ALT, CTRL, and SHIFT modifier keys modify a tool or switch to a complementary tool while the modifier key is pressed. Tips: · Set a pair of keys to commonly used keystrokes, such as [ and ] to decrease and increase your brush size in Photoshop. · Set a key to a commonly used keyboard shortcut in order to open files or start an application. · If you prefer not to (or cannot) use the side switches on your Grip Pen, then set a key to right- or double-click. See the electronic Software User's Manual for more details on the available key settings. Working with your Cintiq Page 27 Using the Touch Strips The customizable Touch Strips can be operated in several different ways: · Standard operation: Slide your finger up or down to zoom, scroll, or issue the assigned keystroke function. By sliding your finger over the Touch Strip you can quickly zoom in or out, scroll up or down, or perform other functions. You can do this with your secondary hand while using your primary hand to work with the Grip Pen. Each Touch Strip can also be set to issue custom keystrokes. For example, you might set a Touch Strip action to change brush sizes or cycle through layers when working in Photoshop. By default, the Touch Strips enable you to zoom in most graphics applications and to scroll in other applications. · · Continuous operation: Press and hold your finger at either end of the Touch Strip to continuously scroll. This is useful for scrolling through long documents or web pages. Single step operation: Press and release your finger at either end of the Touch Strip to zoom, scroll, or issue the assigned keystroke function one step at a time. Press and hold here for continuous operation, or press and release for single step operation. Working with your Cintiq Page 28 · Touch Strip Modifier operation: The upper pair of ExpressKeys located to the left and right of your pen display enable you to modify the function of the corresponding Touch Strip. To modify the Touch Strip function: 1. Press and hold the ExpressKey. 2. Then slide or press your finger on the Touch Strip. Note: In the Wacom Tablet control panel, the ExpressKey must be set to TOUCH STRIP MODIFIER in the EXPRESSKEYS 2 tab and an alternate function must be defined for that ExpressKey in the TOUCH STRIP tab. Each Touch Strip can be independently customized to meet your needs. Tip: Photoshop users who frequently change brush sizes may want to assign the [ and ] keys to a Touch Strip. Sliding your finger up or down the Touch Strip will then change the brush size without the need to reach for the keyboard or access the Photoshop BRUSHES palette. This is the default setting for the Touch Strip when pressing the outer ExpressKey in each upper pair group. Refer to the electronic Software User's Manual for detailed information on customizing the way your display tablet Touch Strips work. Working with your Cintiq Page 29 Setting up your work area The Cintiq 20WSX pen display and stand were designed to provide you with the widest possible range of flexibility and ergonomic work approach. The design allows you to quickly adjust Cintiq to a different position whenever the need arises. You may want to experiment with different height adjustments to determine which best fits your particular working style and tasks. As you work with Cintiq, you can rest your hand lightly on the display screen, just as if it were a drawing board or sheet of paper. To minimize fatigue, organize your work area so you can work comfortably. Position Cintiq, the Grip Pen, and your keyboard so they are easily accessible without unnecessary reaching. The pen display tablet and any other monitors should be positioned so you can view them comfortably with a minimum of eyestrain. Here are some other points to keep in mind: · Take short breaks between tasks to stretch and relax your muscles. · Use a gentle grip when working with the pen. · Alternate tasks throughout the day. · Minimize awkward postures and repetitive movements that cause discomfort. · Alternate between different modes of use. Note: Wacom makes no representation, promise or guarantee that Wacom products will cure or prevent, in whole or in part, mouse-induced repetitive stress symptoms, injuries or conditions. Individual results may vary. Always obtain competent medical advice to determine the most appropriate treatment for your specific situation. By adjusting the Cintiq stand to its lowest position, the pen display unit can be freely rotated on the display stand without touching the desktop. In this position, Cintiq emulates a traditional animator's table and gives you the freedom to rotate the display unit to any angle for the greatest comfort and accuracy of stroke while drawing or editing images. Adjusting the Cintiq stand to its highest position is common when your work requires a large amount of keyboard input. This position is also useful when presenting your work to co-workers or clients. Working with your Cintiq Page 30 Hints: · If the rotation lock screws are attached to the back of Cintiq, they must be removed before Cintiq can be rotated. · Before rotating the display unit, be sure the cable is freely rotating behind the unit. · Because the Cintiq drawing surface will be a little higher than your desk, consider adjusting the height of your desk or chair to assure comfortable use of the device. · · · Maintain a good posture at all times, and change your position if you feel any discomfort due to your work position. Do not pull the cable out of its computer connections by accidentally moving the pen display tablet too far from the computer. An optional pen tether can be used to ensure your pen stays with your pen display tablet. Note: Cintiq can also be mounted to articulated arms or other third-party stands meeting the VESA 100 specification for monitor stands. See Using an alternate mount or stand on page 57 for details. Next step: If you have not already done so, learn about the basics of customizing the Grip Pen. See Customizing on page 32. Working with your Cintiq Page 31 CUSTOMIZING After you master the basics of using your Grip Pen on the Cintiq pen display, you may want to customize the way the pen or pen display works. The Wacom Tablet control panel makes it easy to customize Cintiq and the pen. Opening the control panel To open the control panel, use the Cintiq pen on the pen display tablet: Windows. Click on the Windows START button and choose ALL PROGRAMS. (For Windows 2000, choose the PROGRAMS group.) Then select WACOM TABLET and choose the WACOM TABLET PROPERTIES option. Macintosh. Open SYSTEM PREFERENCES from either the Dock, the Apple menu, or from the APPLICATIONS folder. Then click on the WACOM TABLET icon. After opening the control panel, see Customization basics on page 33. Customizing Page 32 Customization basics This manual only covers the basics of customizing Cintiq. For detailed information see the Cintiq Software User's Manual. If you installed the Wacom tablet software, just open the Wacom Tablet control panel and click on the HELP button to display the manual. You can also access the manual from the Installation menu on the Wacom Pen Tablet Driver CD. Open the Wacom Tablet control panel to customize your product. When you open the control panel, an icon for the Grip Pen is displayed in the TOOL list and the appropriate tabs are displayed. To customize the pen, make your changes to the tab controls. Experiment with different settings to find what works best for you. Any changes you make will take effect immediately, but you can always click DEFAULT to return to the factory settings. Tool Tips are available for most control panel items. Simply position the screen cursor over an item and let it rest there; in a few moments the Tool Tip will pop up. Additionally, your keyboard tab and arrow keys can be used to navigate the control panel. Note: Application-specific settings are for advanced users. This topic is covered in the Cintiq Software User's Manual. The upper portion of the control panel displays icons representing your TABLET, TOOLs, and the APPLICATIONs with customized tool settings. Closes the control panel. Tabs display customizable settings for the selected tool. Choose FUNCTIONS to customize your ExpressKeys, Touch Strips, and Pop-up Menu settings. Choose GRIP PEN to customize your Grip Pen settings. Displays a dialog box containing information about the tablet and tablet software, including an option to access the DIAGNOSTICS dialog box. Displays advanced options. The DEFAULT button resets the selected tab to its default settings. Displays the electronic Software User's Manual. Customizing Page 33 Calibrating Cintiq You will need to calibrate the pen display tablet in order to align the screen cursor position with the position of the pen on the display screen. This is required to adjust for parallax caused by the display screen cover glass and coating. Set Cintiq in its working position, then follow the procedure below. Important: When using a VGA connection with Cintiq, make sure the LCD monitor is properly adjusted before calibrating the tablet. See Adjusting pitch and phase (VGA only) on page 39, and Adjusting the LCD monitor beginning on page 36. · In the Wacom Tablet control panel, select the Grip Pen from the TOOL list and then select the CALIBRATE tab. If you are working with multiple monitors, select the MONITOR option corresponding to the Cintiq display. (Only monitors that are set to one of the resolutions supported by Cintiq will appear in the list.) Click on the CALIBRATE... button to activate the calibration screen. Hold the pen and position your head as you normally do when working with the tablet. Use the pen tip to click on the center of the crosshairs in the upper-left corner. Then click on the center of the crosshairs that are displayed in the lower-right corner. Test the alignment by positioning the pen at a few different points on the display. Click OK to accept the calibration. Click TRY AGAIN to recalibrate. Be sure to read the directions in the calibration screen for detailed instructions and additional options. The calibration setting applies to all applications. Note: If more than one pen display tablet is installed on your system, be sure to select the Cintiq unit you are working with from the control panel's TABLET list. · Crosshairs · · · · Adjustment pattern for pitch and phase. See Adjusting pitch and phase (VGA only) on page 39 for details. Tip: If you prefer to see the screen cursor slightly offset from the actual position of the pen tip, calibrate by clicking on a spot showing that offset from the crosshairs. For example, to have the screen cursor appear 1/10th of an inch above and to the left of the pen tip, calibrate by clicking on a spot 1/10th of an inch below and to the right of the crosshairs. Customizing Page 34 Learning more about Cintiq Refer to the electronic Software User's Manual for detailed information on customizing Cintiq. To view the manual, open the Wacom Tablet Control Panel and click on the HELP button. To read the Software User's Manual before installing Cintiq, first insert the Wacom Pen Tablet Driver CD into your computer's CD-ROM drive. When the software menu appears, select the USER'S MANUAL option. You will need Adobe Reader or another .pdf viewer to view the Software User's Manual. Customizing Page 35 Adjusting the LCD monitor Factory presets, auto-sync, and user settings Factory presets: For optimal display quality, set your video card to Cintiq's native resolution of 1680 x 1050 pixels (WSXGA). See page 62 for signal specifications. Auto-sync: When connected as a VGA display, Cintiq attempts to automatically synchronize to the incoming signal. At the native resolution of 1680 x 1050, the vertical refresh frequency must be set to 60 Hz. For other resolutions, auto-sync will function when the horizontal frequency is between 30 to 82 kHz and the vertical frequency is between 50 to 75 Hz. If a specific resolution and vertical refresh frequency are not supported, you will see an "out of scan range" message. In this case choose a different resolution or refresh frequency. The auto-sync function automatically sets the horizontal and vertical screen position, as well as pitch and phase. If Cintiq does not automatically synchronize with the incoming signal, you can open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option to initiate display synchronization. Additional screen display adjustments can be manually made using the OSD controls. Color calibration: Changing the color, color temperature, contrast, brightness, or backlight from their default settings will invalidate the ICC color profile that was included on the driver CD. Working with on screen display settings Cintiq is equipped with an On Screen Display (OSD) function. The OSD function enables you to adjust and optimize a variety of display settings at the touch of a button. The OSD controls are located on the back of the unit. Simply reach over the top of the display unit to locate the buttons with your fingers. Note: Braille-style dots above the buttons help you to identify each one by touch. Digital/Analog (DVI/VGA) switch (up) (down) MENU button Use this button to open or close the OSD menu. ENTER button Activates or deactivates the selected OSD menu option. Selection buttons Use these buttons to select an option that can then be activated when you press the ENTER button. After activating a selected option, press the up button to increase a selected item value, and press the down button to decrease it. Customizing Page 36 The basic process for working with the OSD is as follows: · Press the MENU button to open the OSD main menu. · Use the up or down buttons to select an option. When the option you want to adjust is highlighted, press the ENTER button. The current settings and adjustment sub-menu for that option will appear. · Use the up or down buttons to adjust the option settings. · When you have made your changes, press the ENTER button to save. To exit, press the MENU button. Note: All settings are automatically saved when the OSD menu closes and will be used the next time the unit receives a similar video signal. This is applicable to all display modes. If you make changes to the display appearance and cannot return to the original settings, use the RESET RECALL option to return Cintiq to its original factory defaults. When you open the On Screen Display (OSD), the following menu options are displayed as icons: CONTRAST. Select to increase or decrease image contrast. BRIGHTNESS. Select to increase or decrease image brightness. PHASE. (VGA only) Select to reduce or eliminate horizontal distortion lines. To automatically adjust, use the RESET option. PITCH. (VGA only) Select to reduce or eliminate vertical distortion lines. To automatically adjust, use the RESET option. HORIZONTAL CENTER. (VGA only) Select to move the screen image left or right. To automatically adjust, use the RESET option. VERTICAL CENTER. (VGA only) Select to move the screen image up or down. To automatically adjust, use the RESET option. MENU POSITION. Select to move the OSD menu around the display screen. LANGUAGE. Select to choose a language option for the OSD. Customizing Page 37 SETUP. Select to adjust the display screen backlighting and OSD menu display options. BACKLIGHT. Increases or decreases the backlight brightness level. TRANSPARENCY. Adjusts the transparency of the OSD menu. TIME OUT. Sets the display time of the OSD menu, in seconds. SCALE. Enables you to choose how the image is displayed when working at resolutions below 1680 x 1050. FULL resizes the image to fill the whole screen. 1:1 displays the image at the actual resolution. ASPECT resizes the image to fill as much of the screen as possible while maintaining the correct aspect ratio. RESET. Provides two options. · Use AUTO ADJUST to reset only the image parameters. · Use RECALL to reset all screen options to the factory default. Selecting the exit icon exits the RESET window without resetting anything. COLOR. Provides settings for 9300°, 6500°, and 5000° Kelvin. DIRECT displays the colors directly from the video card without any adjustment. When selected, the BRIGHTNESS and CONTRAST settings are also set to DIRECT and cannot be adjusted manually. Also provides a CUSTOM option that enables you to adjust Red, Green, and Blue independently. Choose a setting to work with and press ENTER to activate your selection. Change the CUSTOM setting by selecting the enter icon. In the custom COLOR window, change Red, Green, or Blue to calibrate color. To exit, select the exit icon. Note: Manual changes to the color settings will invalidate the Cintiq color profile. Customizing Page 38 Adjusting pitch and phase (VGA only) Some computers and video cards may not allow the auto-sync function to fully work when Cintiq is first connected. If some portion of text appears blurred, open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option. If the image is still blurred, adjust the pitch and phase manually by following the procedure below. For optimal display quality, set your video card to Cintiq's native resolution of 1680 x 1050 pixels. · · In the Wacom Tablet control panel, select the CALIBRATE tab. If you are working with multiple displays, be sure the display corresponding to Cintiq is selected in the MONITOR menu. Click on the CALIBRATE... button to activate the calibration screen. Using the OSD controls, open the OSD menu and select the Pitch icon. Then adjust the pitch level so that the pattern of fine vertical stripes displays evenly. (For details on changing the OSD settings, see Working with on screen display settings on page 36.) Next, in the OSD menu select the Phase icon and adjust the phase level so that the adjustment pattern shows clearly. After completing these adjustments, press the ENTER and MENU buttons to exit the OSD menu. Click on the CANCEL button or press ESC to exit the calibration screen. · · · · · Adjustment pattern for pitch and phase. Customizing Page 39 Power saving Cintiq conforms to VESA and ENERGY STAR® power saving guidelines. When using Cintiq with a Display Power Management Signaling (DPMS) compliant computer or video card, the display will automatically comply with the below power saving parameters. Computer mode Power ON Standby mode Suspend mode OFF Mode H-sync Yes No Yes No V-sync Yes Yes No No Video Active Blanked Blanked Blanked Power consumption 50 W 2W 2W 1W Power lamp Blue Orange/Blue Orange/Blue Orange Customizing Page 40 TROUBLESHOOTING Most of the time your pen display tablet will work flawlessly. But if you are having trouble, Wacom recommends you do the following: 1. If Cintiq does not function properly, refer to the troubleshooting section below. See also Display troubleshooting on page 45, or look in the Pen tablet troubleshooting on page 47. Your problem may be described there and you can try the solution offered. 2. Open the Wacom pen display Read Me file for late-breaking information. 3. If you are having a compatibility conflict between Cintiq and a new hardware or software product, check if a newer pen tablet software driver is available. See Obtaining driver downloads on page 53 for information on downloading an updated software driver. Wacom periodically updates the software driver to maintain compatibility with new products. 4. Check the FAQs (Frequently Asked Questions) on the Wacom web site for your region. 5. If you have tried the suggestions in this manual and still cannot resolve the problem, then contact Wacom for Technical Support. See the Read Me file for information on where to obtain support for your region. Testing Cintiq 1. If the Cintiq power LED does not light, check the following: · First verify that the green light on the power adapter is on. If the light is not on, check that the power cable is properly connected to the power adapter and to an active AC outlet. · Check that the power adapter cable is securely connected to the Cintiq power cable and that the Cintiq power switch is turned on. The Cintiq power LED will glow orange or blue whenever Cintiq is on. Important: Use only the AC adapter that came with your pen display. Other adapters may cause damage to your product. 2. If there is no display: · Make sure that your computer is turned on. The power LED will light blue when the proper video signal is received, and orange if there is no video signal or if the computer is in a power saving mode. · Verify that Cintiq is connected to an active DVI-I, DVI-D, or VGA connector and that the DVI/VGA switch on the back of Cintiq is set to the correct video setting. · Check that your video card has been properly installed and is functional. If you have another display that is compatible with your video card, you can connect that display to the card in order to verify that the video card is operating correctly. Troubleshooting Page 41 3. Verify that the tablet and Grip Pen are working: · Press the Grip Pen tip against the display and verify that the status LED lights blue. · If the LED does not light, verify that Cintiq's USB cable is plugged into an active USB port. If Cintiq is plugged into a USB hub, try plugging Cintiq directly into the USB port on your computer. · Be sure that the USB port to which you are connecting Cintiq has not been disabled. It may be necessary to check your system BIOS setting to verify that you have connected Cintiq to an active USB port. · The status LED will light blue when Cintiq is registered as a USB device and the pen tip is pressed against the display. 4. Check the pen. If you cannot make a selection on the display screen with the pen: · Test the pen by pressing the pen tip or the eraser against the surface of the pen display tablet. The status LED should light blue. · Now, without applying pressure to the pen tip but keeping the pen within 5 mm (0.2 inch) of the pen display tablet surface, press the side switch. The status LED should again light blue. · If the status LED does not light blue for these tests, be sure you are using the correct pen that came with Cintiq. · See Testing your input tools and pen display controls on page 43 and Testing a pen on page 44 for more information. If you are still having problems, you may have a defective pen or pen display tablet. Troubleshooting Page 42 Testing your input tools and pen display controls If the Grip Pen, or the Cintiq ExpressKeys or Touch Strips do not work as you expect, it is a good idea to first check the assigned functions or reset them to their default conditions. A quick way to reset a pen to its default settings is to remove it from the TOOL list by clicking on the list's [ ­ ] button. After the pen has been removed, place it back onto the display screen surface and the pen will be re-added to the TOOL list with its default settings. Open the Wacom Tablet control panel and click on the ABOUT button. In the dialog box that appears, click on the DIAGNOSE... button to open the DIAGNOSTICS dialog box. The DIAGNOSTICS dialog box displays dynamic information about the Cintiq pen display tablet and pen. This information is used when testing Cintiq and your input tool(s). If more than one Cintiq unit is connected to your system, be sure to select the unit for which you are testing in the TABLET INFO column. Note: When testing your tool buttons, if a button is set to POP-UP MENU or OPEN/RUN..., that function will occur when the button is pressed. In this case you may want to change that button's function before testing. Testing the ExpressKeys 1. With the DIAGNOSTICS dialog box open, observe the TABLET INFO column as you test the ExpressKeys. If you have more than one Cintiq unit connected to your system, be sure to select the unit you are testing from the TABLET INFO column. 2. Test the ExpressKeys by pressing them one at a time. Each time you press a key, its number will be displayed next to either the LEFT KEYS or RIGHT KEYS category, depending on which keys group you are testing. When you are done, click the CLOSE button to exit the dialog box. Testing the Touch Strips 1. With the DIAGNOSTICS dialog box open, observe the TABLET INFO column as you test each Touch Strip. If you have more than one Cintiq unit connected to your system, be sure to select the unit you are testing from the TABLET INFO column. 2. Slide your finger up or down along the entire length of the Touch Strip you want to test. As you touch and move your finger along the Touch Strip, a number will indicate the current finger position for the respective Touch Strip next to LEFT TOUCH STRIP or RIGHT TOUCH STRIP. When you are done, click the CLOSE button to exit the dialog box. Troubleshooting Page 43 Testing a pen 1. While observing the POINTING DEVICE INFO column, bring your pen within 5 mm (0.2 inch) of the display screen. A value for PROXIMITY, the DEVICE NAME, DEVICE TYPE, and a DEVICE S/N (serial number) should be displayed. If you have more than one Cintiq unit connected to your system, be sure to select the unit for which you are testing a pen in the TABLET INFO column. 2. Move your tool along the tablet surface. The X and Y DATA values should change to reflect the tool position. 3. Test your pen switches. The Cintiq status LED should light blue each time you click with the tool tip, press the side switch, or press the tool's eraser to the display screen. · Press on the display screen surface with the tool tip ­ the SWITCHES state and PRESSURE value should change. (PRESSURE should change from approximately 0% with no pressure applied to approximately 100% when full pressure is applied.) · Next, press the side switch without pressing the tip to the tablet ­ the SWITCHES state should change. (For the Grip Pen, do this for both positions of the DuoSwitch.) Pen Airbrush Tip = 1, DuoSwitch (lower position) = 2, DuoSwitch (upper position) = 3, Eraser = 1 Tip = 1, Side Switch = 2, Eraser = 1 · · Press the tool's eraser to the display screen ­ the SWITCHES state and PRESSURE value should change. (PRESSURE should change from approximately 0% with no pressure applied to approximately 100% when full pressure is applied.) For the optional Airbrush, move the fingerwheel forward ­ the WHEEL value should decrease to a value of approximately 0 when the fingerwheel is all the way forward. Move the fingerwheel backward ­ the WHEEL value should increase to approximately 1000 when the fingerwheel is all the way back. 4. Test tilt for the x-axis by moving the pen from a vertical position toward the right; the X TILT value should change from approximately 0 to +60. Now move the tool to the left of vertical; the X TILT value should change from approximately 0 to -60. 5. Test the tilt for the y-axis by moving the pen from a vertical position toward the bottom of the tablet; the Y TILT value should change from approximately 0 to +60. Now move the tool toward the top of the tablet; the Y TILT value should change from approximately 0 to +60. 6. For the optional 6D Art Pen, test the rotation feature by placing the pen tip on the display screen surface and slowing rotating the pen on its axis. The ROTATION value should change as you rotate the pen. 7. When you are done, click on the CLOSE button to exit the dialog box. Troubleshooting Page 44 Display troubleshooting If you encounter problems with the Cintiq display, refer to the following tables; your problem may be described here and you can try the solution offered. For additional information about color issues, refer to the documentation that came with your operating system or applications. General display problems No display. The power LED is off. No display. The power LED is lit blue. The power LED is lit orange. No display or a "no input signal" message briefly appears on your display screen. · Verify that the light on the AC power adapter is on and the power cable is securely plugged into Cintiq's power receptacle. Check that Cintiq's power switch is turned on. Check the contrast, brightness, and backlight controls. Adjust as necessary, or open the OSD menu, go to the RESET menu and select the RECALL option. Your computer may be in a power management mode. Touch the pen tip to the Cintiq display screen, move the mouse, or depress any key on your keyboard. Turn off both your computer and the Cintiq pen display, and check the video cable for bent or broken connector pins. Then properly reconnect the video cable and turn on Cintiq and your computer. Verify that the DIGITAL/ANALOG (DVI/VGA) switch is properly set. Restart your computer after changing the position of the switch. Verify that the video card is properly installed. Check that your computer is turned on. Verify that the video cable is properly connected. Turn off both your computer and the Cintiq pen display, and check the video cable for bent or broken connector pins. Then properly reconnect the video cable and turn on Cintiq and your computer. The input signal frequency is incorrectly set or not compatible with Cintiq. Set the refresh rate (vertical frequency) to 60 Hz (or between 50 and 75 Hz if you are using a resolution of less than 1680 x 1050 pixels). If your video card driver supports adjustment of the horizontal frequency, make sure it is set to some value between 30 and 82 kHz. On a single monitor system you will need to connect a different display to change the refresh rate. The resolution is set too high (1680 x 1050, maximum). Set the display properties to detect plug and play monitors. Do not extend the video cable. Do not use an input selector switch box. · · · · No display or a "cable disconnect" message briefly appears on your display screen. · · · · An "out of range" message briefly appears on your display screen. · The image appears multiple times on the display. · · · Troubleshooting Page 45 When a still image is displayed for a long period of time without refreshing the screen, an afterimage remains for a short period of time. Color quality is inaccurate. · Use a screen saver or other power management feature. · · · The color white does not display as white. · · · Open the OSD menu, go to the RESET menu and select the RECALL option. Be sure the Cintiq color profile has been installed and is selected as the profile for use with your operating system and applications. Any changes to the contrast setting should be made in small increments as changes in contrast may affect color accuracy. Be sure the Cintiq color profile has been installed and is selected as the profile for use with your operating system and applications. Verify also that the display is operating at the factory default settings. If that is not sufficient, then adjust color as necessary. For details on color management, refer to your operating system and application documentation. Verify that the video cable and connector are fully connected. VGA problems The display ripples or flickers. · Open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option. If necessary, manually adjust the pitch and phase settings. Verify that the display adapter or video card matches the specifications for Cintiq. Adjust the refresh rate in the Display Properties control panel. Set the display resolution of your video card to 1680 x 1050. Turn off the Cintiq, then turn it back on. Open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option. If necessary, manually adjust the brightness, pitch and phase settings. Open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option. If necessary, manually adjust the pitch and phase settings. Open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option. If this does not solve the problem, go to the RESET menu and select the RECALL option to set the display back to the factory default settings. Open the OSD menu, and as necessary adjust pitch and phase. · · · · · The display is not clear. Text or other portions of the screen appear blurred. The display and LCD panel are not lined up. The display size is not correct. The display ripples or shows a moiré pattern. The display color is not even. · · · Troubleshooting Page 46 Pen tablet troubleshooting If you encounter problems with the Cintiq pen display tablet, refer to the following tables. Your problem may be described here, and you can try the solution offered. Be sure you refer to the Cintiq Read Me file for the latest information. For additional information, visit Wacom's web site at http://www.wacom.com/productsupport and follow the links to the FAQs. General problems The computer does not have an available USB port. The pen display power LED is off. Check if there is an available USB port on a USB hub. If not available, you will need to add a USB hub or USB card. Make sure the pen display power switch is turned on. Check that the AC power adapter is plugged into both the pen display and an active power outlet and that the green light on the power adapter is on. Use only the power adapter that came with the pen display; other adapters may cause damage to your product. The tablet driver software was not installed or did not load properly. Make sure the tablet driver software is installed and functioning. Install the pen tablet driver software in accordance with the instructions found in the Installation section of this manual. Some applications require that you turn on the pressure capabilities within the application or selected tool before the pen will respond as a pressure-sensitive tool. Open the Wacom Tablet control panel and go to the PEN tab. Try using a lighter TIP FEEL. Open the Wacom Tablet control panel and go to the PEN tab. Move the TIP FEEL slider toward FIRM, or select the DETAILS... button and increase the CLICK THRESHOLD setting. If this does not help, see Testing Cintiq on page 41. Be sure you are quickly tapping the display screen twice in the same place on the pen display tablet's active area. Wacom recommends using the side switch to double-click. Open the Wacom Tablet control panel and go to the PEN tab. Try increasing the TIP DOUBLE CLICK DISTANCE or using a lighter TIP FEEL. Windows: Try setting your system to launch programs with a single click. See Pen operations on page 24. The pen works only in mouse mode, and does not draw with pressuresensitivity. The pen does not draw with pressure-sensitivity. Clicking is difficult. The pen selects everything or will not stop drawing. Double-clicking is difficult. Troubleshooting Page 47 The eraser selects everything or will not stop erasing. You notice a delay at the beginning of pen strokes. You have to press hard with the pen when clicking or drawing. The pen tip does not function. Changing the function settings for an input tool has no effect. The side switch does not work. Open the Wacom Tablet control panel and go to the ERASER tab. Move the ERASER FEEL slider toward FIRM, or select the DETAILS... button and increase the CLICK THRESHOLD setting. If this does not help, see Testing Cintiq on page 41. Open the Wacom Tablet control panel and go to the PEN tab. Try decreasing the TIP DOUBLE CLICK DISTANCE. If that does not work, try dragging the TIP DOUBLE CLICK DISTANCE slider to the OFF position in order to turn off double-click assist. Open the Wacom Tablet control panel and go to the PEN tab. Move the TIP FEEL slider toward SOFT, or select the DETAILS... button and decrease the SENSITIVITY and CLICK THRESHOLD settings. Be sure you are using the pen that originally came with your pen display tablet, or an Intuos3 pen. Other pens may not function properly on the Cintiq pen display. Make sure the status LED lights blue when the pen tip is pressed. If the LED does not light, verify that the USB cable is plugged into an active USB port on your computer or on a USB hub. If the LED still does not light, you may have defective hardware (see Troubleshooting on page 41). Open the Wacom Tablet control panel. Check the control panel's PEN tab and verify that the tip is assigned to a CLICK function. Make sure that you change the settings for the tool and application that you are using. See the electronic Software User's Manual for details on working with multiple tools and with application-specific settings. Be sure you are using the pen that originally came with your pen display tablet, or an Intuos3 pen. Other pens may not function properly on the Cintiq pen display. Be sure you press the side switch when the pen tip is within 5 mm (0.2 inch) of the pen display tablet's active area ­ do this without pressing down on the pen tip. From the Wacom Tablet control panel, verify that the side switch is set to the proper function you are expecting to occur for the application (and input tool) you are using. Check also which SIDE SWITCH MODE option is selected. (These options are accessed by clicking on the control panel OPTIONS... button.) Make sure the status LED lights blue when you press the side switch. If the LED does not light, verify that the USB cable is plugged into an active USB port on your computer or on a USB hub. If the LED still does not light, you may have defective hardware (see Troubleshooting on page 41). Troubleshooting Page 48