User manual WELLTECH FXO GATEWAY H.323 3806

FXO GATEWAY User Manual (3802/04/06) STEPS IN CONFIGURATION 1. START UP 1.1 Introduction 1.2 Features and specification 1.3 Accessories and equipment 1.4 Appearance 1.4.1 3802 1.4.2 3804 1.4.3 3806 2. HOW TO SETUP AND CONNECT BASICALLY 2.1 System Requirement 2.2 IP Environment Setting 2.2.1 For Windows 2000/NT 2.3 Network configurations in your gateway 2.3.1 Static ip address 2.3.2 DHCP mode 2.3.3 PPPoE mode 2.4 Making a VoIP Call 2.4.1 Configure the gateway into the Peer-to-Peer mode 2.4.2 Configure the gateway into the GK routed mode 2.4.2.1 The type in GK routed mode 3. COMMAND LIST 3.1 Hyper Terminal Setting 3.2 Command List 3.2.1 [help] command 3.2.2 [quit] command 3.2.3 [debug] command 3.2.4 [reboot] command 2 3 3 3 4 5 5 6 7 9 9 10 10 12 14 16 17 18 19 21 22 24 24 27 27 27 28 28 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 3.2.5 [flash] command 3.2.6 [commit] command 3.2.7 [ifaddr] command 3.2.8 [time] command 3.2.9 [ping] command 3.2.10 [greetrd] command 3.2.11 [pbook] command 3.2.12 [pppoe] 3.2.13 [ddns] command 3.2.14 [sysconf] command 3.2.15 [h323] command 3.2.16 [voice] command 3.2.17 [tos] command 3.2.18 [tone] command 3.2.19 [support] command 3.2.20 [group] command 3.2.21 [bureau] command 3.2.22 [prefix] command 3.2.23 [rom] command 3.2.24 [passwd] command 29 29 30 32 32 33 35 38 38 40 44 46 48 49 50 51 53 54 55 57 1 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Steps in configuration STEP 1 Start Up To check out the peripheral equipments and understand the feature of this gateway. Please read this step very carefully before starting the configuring. Connecting the gateway and computer to start configuring by WEB GUI. STEP 2 How to Setup and Connect basically Setting the ip address for this gateway to make sure that it could connect with the internet. Setting the configurations of dialing, including the Peer-To-Peer, GK mode and how to set these tables to make calls by this gateway easily. The other configurations of make call will be discussed in this step. STEP 4 Command List To explain the meaning of the command in the command line interface and example the usage of the command. To get more usages or configuration in this step and study about the command line configuration. 2 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 1. Start Up 1.1 Introduction The WellGate FXO gateway provides voice/fax service over IP network with H.323 v3 protocol. By connecting to your existing ADSL or cable modem service, which allows the use of a single, network for voice and fax services with consequent saving in network infrastructure and greatly reduced telephone charges. Ideal solution for providing low cost communications between headquarters and branch offices in the world, as well as for SOHO and office telephony applications. WellGate FXO GateWay provides analog lines to connect local PSTN/PTT interface (FXO), and converts voice/fax signal onto IP network. The management feature is via RS-232C COM port and TELNET. 1.2 Features and specification Features - ITU-T H.323 v3 compliance - Automatically Gatekeeper Discovery - Peer-to-Peer mode (non-Gatekeeper) - Support auto-attendant (2nddial Tone / Voice greeting) - Dimensions : 221mm(W)*42mm(H)*217mm(L) - Line hunting - 2(3802)/4(3804)/6(3806) RJ-11 FXO ports - E.164 (Telephone Number Plan) - DTMF dialing - DTMF detection/generation - TFTP software upgrade - Remote configuration/reset via Telnet - LED indication for system status - LAN interface : One RJ-45 connector of 10Base-T - Microsoft Netmeeting v3.0 compatible - Support static IP and DHCP - QoS by ToS (Type Of Service) 3 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 - SNTP (Simple Network Time Protocol) Security: Password setting Audio feature Codec -- G.711 a/ law, G.723.1 (6.3K/bps), G.729A (Optional) VAD (Voice Activity Detection), CNG (Comfort Noise Generate) G.168/165-compliant adaptive echo cancellation Dynamic Jitter Buffer Bad Frame Interpolation Call Transfer (H.450.2) Call Forward (H.450.3) Call Hold (H.450.4) Gain Settings Provide Call Progress Tone: Dial tone, busy tone, call-holding tone and ring-back tone Management Features: Two easy ways for system configuration - Console port: RS-232C port - TELNET - HTTP Brower (e.g. Internet Explorer) 1.3 Accessories and equipment The voice gateway in 2/4/6 FXO ports models and only one RJ-45 connector (WAN). The AC adapter. The CD of user manual. The connection cable in RS-232 interface. 4 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 1.4 Appearance 1.4.1 3802 Front panel: The LED light provides system message of WellGate3802. Power : Light on means WellGate3802 is power on. L1-L2 : Light on means the line is in use. Link : Light on means WellGate3802 is connected to the network correctly. Act : LED should be light on and in flash display when data is transmitting. Ready : 1. Light on and in slow flash means WellGate3802 is in operation mode. Status : 1. Light on means WellGate3802 successfully registered to Gatekeeper when it is set as Gatekeeper Mode. 2. LED flash means WellGate3802 is not registered to Gatekeeper when it is set as Gatekeeper Mode. 3. Or when WellGate3802 is in downloading mode, LED should be flash as well. 4. Light off means WellGate3802 is in Peer-to-Peer Mode. Back panel: 5 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 1.4.2 3804 Front panel: The LED light provides system message of WellGate FXO GateWay. Power : Light on means WellGate FXO GateWay is power on. L1-L4 : Light on means the line is in use. Link : Light on means WellGate FXO GateWay is connected to the network correctly. Act : LED should be light on and in flash display when data is transmitting. Ready : 1. Light on and in slow flash means WellGate FXO GateWay is in operation mode. Status : 1. Light on means WellGate FXO GateWay successfully registered to Gatekeeper when it is set as Gatekeeper Mode. 2. LED flash means WellGate FXO GateWay is not registered to Gatekeeper when it is set as Gatekeeper Mode. 3. Or when WellGate FXO GateWay is in downloading mode, LED should be flash as well. 4. Light off means WellGate FXO GateWay is in Peer-to-Peer Mode. Back panel: 6 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 1.4.3 3806 Front panel: The LED light provides system message of WellGate3806. Power : Light on means WellGate3806 is power on. L1-L6 : Light on means the line is in use. Link : Light on means WellGate3806 is connected to the network correctly. Act : LED should be light on and in flash display when data is transmitting. Ready : 1. Light on and in slow flash means WellGate3806 is in operation mode. Status : 1. Light on means WellGate3806 successfully registered to Gatekeeper when it is set as Gatekeeper Mode. 2. LED flash means WellGate3806 is not registered to Gatekeeper when it is set as Gatekeeper Mode. 3. Or when WellGate3806 is in downloading mode, LED should be flash as well. 4. Light off means WellGate3806 is in Peer-to-Peer Mode. Back panel: 7 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 1. Ethernet Port LAN/WAN: 10/100 Base-T; RJ-45 socket, complied with ETHERNET 10/100base-T. The pin-out is as following: PIN 1, 2: Transmit PIN 3, 6: Receive 2. COM: RS232 console port (DB-9pin male connector) Note: use straightforward cable to connect to your computer. PINOUTS Pin Name Dir 2 3 5 RXD TXD GND Description Receive Data Transmit Data System Ground 3. TEL: RJ-11 connector, FXS interface is for connecting the analog phone sets or trunk line of 8 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 PABX. 4. LINE: RJ-11 connector, FXO interface is for connecting the extension line of PABX or PSTN Line. 5. 12V DC: Input AC 100V~120V;output DC12V. 2. How to Setup and connect basically 2.1 System Requirement 1. One PC (a) Pentium 100 or above, 64 RAM, Windows 98 or above. (b) Ethernet card or COM port 2. One standard straightforward RS-232 cable (female connector to Gateway side). 3. PBX extension Lines or PSTN Lines. 4. Software tools (a) Hyper Terminal, TELNET, Web Browser. (b) Gatekeeper (optional). 9 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 2.2 IP Environment Setting User must prepare a valid IP address, complied with IP Network, for Gateway's proper operation. For testing the validation of chosen IP address, using the same IP configuration in other PC or Notebook, and then try to connect to Public Internet (go to well-known website, receive Internet mail, or ping a specific public IP address). If it works, use the same IP address and network configuration for Gateway. Please follow up the step for the configuration of your computer or notebook. 2.2.1 For Windows 2000/NT Please make sure that the network interface of your computer is working fine and the cross over line (RJ-45) is connecting with the computer correctly or you could use a hub to connect with your computer and this gateway. Turn on your computer and configure the network parameter as follow: Go to the start menu and enter the setting area. Click control panel. Enter the network configuration. 10 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Figure 2.1: Network Configuration Select the Property of the LAN card. Setup the ip address, subnet mask and default gateway as below: Figure 2.2: Configure the network Click OK after you finished the network setup. 11 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 The default ip address, netmask and default gateway address of the gateway is 10.1.1.3, 255.255.0.0, 10.1.1.254. 2.3 Network configurations in your gateway Key in the ip address of the gateway (http://10.1.1.3) with the browser 12 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 After key in the ip address, you have to enter the user name and password to enter the WEB configuration. (Username: root ; No password) Figure 2.3: Login the username and password You will enter the main page of the configuration after key in the login name and password correctly: 13 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Figure 2.4: The main WEB configuration Press the Network Interface to configure the networking of your gateway: Figure 2.5: The Network Interface 2.3.1 Static ip address 14 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Please get the correct ip address, netmask and default gateway address from your ISP first. Press the OK button if you finished. Figure 2.5: Configure the static ip address Press the commit if you finish the configuration. Figure 2.6: Commit the data 15 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Press the reboot if you want the configuration executed. Figure 2.7: Reboot the system 2.3.2 DHCP mode Enable the DHCP if you are using the cable modem or DHCP server. 16 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Figure 2.8: Enable the DHCP function Please commit the data and reboot the machine after you enable the DHCP function. 2.3.3 PPPoE mode Press the PPPoE Configuration and put the info of the PPPoE account and password in the configuration table. 17 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Figure 2.9: Configure the PPPoE function Please commit the data and reboot the machine after you finished the configuration of PPPoE. 2.4 Making a VoIP Call There are two modes that you could configure the gateway for making VoIP calls. One is the Peer-to-Peer mode, another is GK routed mode. The configurations and functions are different. Please make sure about the mode you want and follow up the step to configure your gateway. 18 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 2.4.1 Configure the gateway into the Peer-to-Peer mode Enter the H323 Configuration table and change the mode to Peer-to-Peer. Figure 2.10: Configure the Peer-to-Peer mode Press the OK button which is on the buttom of this page to save the configuration. Enter the Phone Book configuration table and configure the name, ip address and phone number of the destination. 19 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Figure 2.11: Phone Book Example Figure 2.12: The example of Phone Book configuration This is the first record of Phone Book. So the index is 1 The name of the destination: test 20 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 The E164 number (phone number) of the destination: 123 The ip address of the destination: 10.1.1.100 Press the "Add Data" button when you finished, and the new table will display on the first index if you press the Phone Book configuration button. Figure 2.13: To show the Phone Book record Please Commit it and Reboot the system if the configuration is finished. 2.4.2 Configure the gateway into the GK routed mode Enter the H323 Configuration table and change the mode from Peer-to-Peer to GK routed. To change the GK information from your service provider (Ex: The Gatekeeper IP, Registered Prefix and Registered Alias). 21 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Figure 2.14: Configure the GK info Press the OK button which is on the buttom of this page to save the configuration. Figure 2.15: Press OK to save the data Press the Commit Data and Reboot System buttons when you finished the configuration. 2.4.2.1 The type in GK routed mode There are two types in the GK routed mode you could choose. One is Gateway type and another is Terminal type. There are some different functions, applications and configurations between the Gateway type and Terminal type. 22 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 In FXO series gateway, the only difference between the Gateway and Terminal type is for registering on the Cisco GK. The Terminal type is needed if the endpoints want to register on the Cisco GK successfully. But all the configuration and function is the same if you set the gateway in Gateway or Terminal type. 23 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 3. Command List 3.1 Hyper Terminal Setting A terminal emulator is needed when using RS-232 port to configure Gateway. There are kinds of terminal emulator software. Here, we use Microsoft HyperTerminal to depict how to set up terminal emulator: 1. Execute the Hyper Terminal program, and then the following windows will pop-up on the screen. (START ­ Program files ­ Accessories ­ Communication ­ Hyper Terminal) Figure 3.1: Hyper Terminal 2. Define a name such as `wg37' for this new connection. 24 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Figure 3.2: Edit the name of the connection 3. After pressing OK button, the next window appear, and then choose COM1/2 Port, which you are going to use. Figure 3.3: Pick up the right interface to use 4. Configure the COM Port Properties as following: 25 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Bits per second: 9600 Flow control: None Figure 3.4: Configure the right Bps and control 5. Press `OK' button, and then start to configure Gateway. 26 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 3.2 Command List 3.2.1 [help] command Type help or man or ? to list all the available command. 3.2.2 [quit] command 27 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Type quit will quit the WellGate FXO GateWay configuration mode. And turn back to login prompt. Note: It is recommended that type the "quit" command before you leave the console. If so, WellGate FXO GateWay will ask password again when next user connects to console port. 3.2.3 [debug] command Open debug message will show up specific information while WellGate FXO GateWay is in operation. After executing the debug command, it should execute command debug -open as well. One example is demonstrated below. Parameters Usage: -status Display the enabled debug flags. -add Add debug flag. -- h323 : h323 related information -- vp : voice related information -delete -open -close Remove specified debug flag. Start to show debug messages. Stop showing debug messages. 3.2.4 [reboot] command After commit command, type reboot to reload WellGate FXO GateWay in new configuration. The procedure is as below: 28 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 3.2.5 [flash] command This command will clean the configuration stored in the flash rom and reboot WellGate FXO GateWay in factory default setting. Parameter Usage: -clean clean all the user-defined value, and reboot WellGate FXO GateWay in factory default mode. Note: It is recommended that use "flash ­clean" after application firmware id upgraded. Warning: Once users execute flash ­clean, all the configurations of WellGate FXO GateWay will be cleaned. This can only be executed by user who log in with root 3.2.6 [commit] command Save changes after configuring the WellGate FXO GateWay. ------------------------------------------------------------------------------------------------- 29 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Note: Users should use commit to save modified value, or they will not be activated after system reboot. 3.2.7 [ifaddr] command Configure and display WellGate FXO GateWay network information. 30 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Parameters Usage: -print print current IP setting -ip assigned IP address for WellGate FXO GateWay -mask internet subnet mask -gate IP default gateway -dhcp Dynamic Host Configuration (1 = ON; 0 = OFF) -sntp Simple Network Time Protocol (1 = ON; 0 = OFF) When SNTP function is activated, users have to specify a SNTP server as network time source. An example is demonstrated below: ------------------------------------------------------------------------------------------------while 10.1.1.1 stands for SNTP server's IP address. -http -dns Change http port. User can change default HTTP port(80) to another one for security or NAT application. Set DNS server IP address. User can set one or two sets of DNS server. (ifaddr ­dns 1 "primary DNS server IP address" ; ifaddr ­dns 2 "secondary DNS server IP address") Set timezone for WellGate FXO GateWay. User can set different time zone according to the location WellGate FXO GateWay is. For example, in Taiwan the time zone should be set as 8,which means GMT+8. Set management center IP address. IF user specifies management center IP address, WellGate FXO GateWay will send information to management center, let user can easily configure via management center interface. (sysconf ­cmcenter "IP address of management center") -timezone -cmcenter Note: management center is optional software to help user can easily configure WellTech products, please contact your reseller to know more about it. -ipsharing Specify usage of an IP sharing device and specify IP address. If WellGate 31 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 FXO GateWay is behind a IP-sharing , user can enable IP sharing function and specify public IP address of IP-sharing. 3.2.8 [time] command When SNTP function of WellGate FXO GateWay is enabled and SNTP server can be found as well, type time command to show current network time. ------------------------------------------------------------------------------------------------- 3.2.9 [ping] command Use ping to test whether a specific IP is reachable or not. For example: if 192.168.1.2 is not existing while 210.63.15.32 exists. Users will have the following results: 32 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 3.2.10 [greetrd] command This command is for user to record their own greeting and analyze disconnect tone. If WellGate FXO GateWay can't hang up call and release line correctly, please use this function to analyze disconnect tone of PSTN side. 1. Greeting Voice Record : please follow instructions on screen ; first, call in line1 of WellGate FXO GateWay from PSTN side(now can't hear greeting) and press "enter" to start record .After finishing recording, please press "enter" again to stop recording. Then choose "y/n" to replay and save or not. 33 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 2. Disconnect Tone Analysis : please follow instructions on screen ; first call in line1 of WellGate FXO GateWay from PSTN side(now can't hear greeting), hang up the phone and press "enter" to start record disconnect tone. Finally, choose "y/n" to save data analyzed or not. Notice that system will save one set of frequency analyzed and 4 set different on/off time in "busytone1","busytone2" , reordertone1" , "reordertone2" (Please refer to tone command) . If WellGate FXO GateWay still can't hang up call correctly, it could be tone cadence issue (on/off time). Please count on/off time and configure it into tone command. 34 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 3. exit : exit this command 3.2.11 [pbook] command Phone Book function allows users to define their own numbers, which mapping to real IP address. It is effective only in peer-to-peer mode. When adding a record to Phone Book, users do not have to reboot the machine, and the record will be effective immediately. 35 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 ------------------------------------------------------------------------------------------------- Parameter Usages: -print print out current contents of Phone Book. Users can also add index number, from 1 to 100, to the parameter to show specific phone number. Note: means the sequence number in phone book. If users do request a specific index number in phone book, WellGate FXO GateWay will give each record a automatic sequence number as index. 36 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 -add -search -delete -insert -modify add a new record to phone book. When adding a record, users have to specify name, ip, and e164 number to complete the command. search a record in phone book. The searching criteria can be name, ip, or e164. delete a specific record. "pbook ­delete 3" means delete index 3 record. add a new record and force to assign a specific index number for it. modify an existing record. When using this command, users have to specify the record's index number, and then make the change. Phonebook Rules: To meet the requirements of communicating with trunk gateway or other applications, Phonebook has following characteristics to be noticed. When the destination side is a terminal, for ex: IP Phone or soft phone, e164 number stands for exact destination phone number. When the destination side is a gateway, for ex: T1/E1 gateway, e164 phone number stands only for gateway prefix. That is to say, users have to continue to dial destination number, following the prefix number. A example is as below: A WellGate FXO GateWay In Phonebook, there's a record : Index Name IP E164 1 B_gateway 192.168.1.2 0 ------------------------------------------------------------------------------------------B E1 trunk gateway, which connects to PSTN with E1 PRI. If users want to make a call to PSTN number "82265699", they have to pickup one of the phone connected to WellGate FXO GateWay, and then dial "082265699". After receiving the complete dialed number, WellGate FXO GateWay will search for its Phone Book, find "0" as matched prefix, and then dial out to B's IP address directly with destination e.164 (phone number) "82265699". Pleased be noted that "0" is eliminated from WellGate FXO GateWay itself. Note:1. Because of above characteristics, users have to take care of the number plan very well to avoid the numbering conflict. If users already defined "0" for specific trunk gateway, other terminal started with "0" shall be avoided, or the number will be routed to the trunk gateway defined "0". 2. If user wants to set 2 sets of similar e164 such as 123 and 1234, please be careful configure 123 first, or it may cause problem when user dial 1234, WellGate FXO GateWay may dials 37 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 out IP address of 123. 3. (1) If called party is FXO product, please set e164 of pbook as e.164 of called party, and remember to set sysconf ­drule in_drop "e.164"(refer to 5.12.)in called party. (2) If called party is FXS product, please set e164 of pbook as prefix of called party, when dialing to different line of FXS product, please dial line number. 3.2.12 [pppoe] Display PPPoE related information. --------------------------------------------------------------------------------------------------PPPoE device information and configuration Usage: pppoe [-print]|[-open]|[-close] pppoe [-dev on/off][-id username][-pwd password] -print Display PPPoE device information. -dev Enable(=1) or Disable(=0) device. -open Open PPPoE connection. -close Disconnect PPPoE connection. -id Connection user name. -pwd Connection password. -reboot Reboot after remote host disconnection. --------------------------------------------------------------------------------------------------Paremeter Usage: -print print PPPoE status. -dev Enable PPPoE Dial-up function -open Open the connection -close Close the connection -id Input the User name ID provided by ISP -pwd Input the User name password provided by ISP -reboot Reboot the PPPoE connection. 3.2.13 [ddns] command Support the DDNS function ------------------------------------------------------------------------------------------------- 38 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Parameter Usages: -enable enable the DDNS function -server enter the server address of the DDNS server you use -hostname enter the domain name address which you get from the DDNS server -id key in your id -passwd key in your password -checkIP enable or disable the check current user's IP address 39 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 -checkIPsrv1 enter the IP address of the check server -checkIPsrv2 the secondary IP address of the check server -delay service delay time -force execute the DDNS function all the times Note: Support DDNS Server: www.3322.org, www.dyndns.org. 3.2.14 [sysconf] command This command displays the system information and configuration. ------------------------------------------------------------------------------------------------- 40 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 - service: 0 Dial In Service in Dial In Service, WellGate FXO GateWay will pick up incoming calls from PSTN, 41 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 play pre-recorded voice greeting or, and then have users to make a 2nd dial to destination. 1/2 HotLine Service (this feature must be implemented after set bureau ­table command) HotLine Service provides Hot Line function, which connects directly to pre-defined destination. For ex: if L1 of WellGate FXO GateWay is assigned to destination address 192.168.1.12 in Hot Line Mode. When users from PSTN make a call to L1 of WellGate FXO GateWay, it will directly connect to 192.168.1.12 without a 2nd dial. 3 The connect signal will sent to IP side if gateway detect the reverse signal. It is using the billing application. - ringdet: to define ring detection method. (0 is for old hardware version; 1 for new hardware version) - plan: It is for setting dial-numbering plan. While e164 number is three digits, the plan should be set as 3 or 0. The plan 0 is for any positive digits use. - port: This command can enable or disable individual port. The default value is set to enable all ports. - idto: The duration of two pressed digits in dial mode -eod: Digit type of end of dialing. ( 0:No end of dialing, 1:[*] button, 2:[#]button ) - seizure: line seizure mode. None (0) when calling from IP side, choose L1 every time if it is available. UCD (1) when calls from IP side, choose L1 for the first time, and L2 for the 2nd time, (cyclic) Note: Do not enable this function together with group (please refer to 5.18). - 2nddial: This command is necessary for setting one time dial method use. While user would like to skip 2nddial process, WellGate FXO GateWay must close 2nddial and set as 0 (2nddial off). The default value is set as 1 (2nddial on). - drule: This command only works while 2nddial is off. When user would like to make an outgoing call or receive an incoming call shortly, it is necessary to set the following 42 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 three commands belonged to drule. drop: drop the dial digit. insert: insert the dial digit filter: filter the dial digit. Note: 1. out: Through WellGate FXO GateWay to dial out to another Gateway's e164 number. When making an outgoing call, it is necessary to set three commands in order, filter, insert then drop. Example: sysconf ­drule out_filter 002886 out_insert 0 out_drop 02 2. in: Through pass WellGate FXO GateWay in order to connect with PSTN / PBX side. When making an incoming call from other Gateway, the three commands is necessary to be set in order, drop, insert, then filter. Example: sysconf ­drule in_drop 002886 in_insert 0 in_filter 02 3. While the specified digit would like to be deleted, use the character x instead of any digits have configured. -askpin: 0 disables ASKPIN function 1 enables ASKPIN function, and apply to the whole unit. Every channel uses the same PINCODE. 2. enables ASKPIN function, and apply to each channel respectively. Every channel uses a different pincode. -ring: To set when dial in WellGate FXO GateWay from PSTN side, WellGate FXO GateWay will pick the call immediately or rings for specific times before picks up. 0 disable: pick up immediately 1-5 times of ring before WellGate FXO GateWay picks up. - keypad: keypad type when relay DTMF signal. 0 In-Band 1 h.245 alphanumeric 2 h.245 signal type 3 q.931 user info 4 RFC2833. - pincode: to specify 2 sets of pincode. - cid : to disable or enable Bellcore format caller ID. If user enables this function, gateway 43 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 will receive caller ID and pass it through. (Note: only FSK type of caller ID is available.) - faxrdd: To add the redundancy depth in fax when the network is not in a good quality. (sysconf -faxrdd 2 ;0:default / 1:first level in depth / 2:highest level in depth) Note: It's will take more bandwidth if the depth level is the highest in 2. 3.2.15 [h323] command This command is to configure H.323 related parameters. ------------------------------------------------------------------------------------------------ 44 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Parameters Usage: -print print current h323 related settings -mode alternatives for gatekeeper or peer-to-peer mode (0=gatekeeper mode; 1=peer-to-peer mode). If users select gatekeeper mode, a extra gatekeeper is need when WellGate FXO GateWay is in operation. -gk to assign gatekeeper's IP address when WellGate FXO GateWay is in gatekeeper mode. -gkname to assign Gatekeeper ID when WellGate FXO GateWay is in gatekeeper mode. -dfgw to set IP address of default gateway, this function is the same as Microsoft NetMeeting. A.To implement this feature both endpoints must be under peer-to-peer mode. B.If the other endpoint is FXO products, such as WellGate 38xx, which have to set as sysconf ­2nddial 0 to make one-stage dialing. From PSTN side dial in WellGate FXO GateWay, when hearing greeting user can dial remote PSTN number under default gateway, WellGate FXO GateWay will automatically dial to default gateway, then default gateway will dial this number to PSTN side. For example, user wants to dial from WellGate FXO GateWay A to ext.888 under WellGate FXO GateWay B, user only have to dial 888 after hearing greeting of WellGate FXO GateWay . C.If the other endpoint is FXS products such as WellGate 35xx : From PSTN 45 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 side dial in WellGate FXO GateWay, when hearing greeting user can dial line number of WellGate 35xx. For example ,user wants to dial from WellGate FXO GateWay to WellGate 3502 the configuration of 3502 is h323 ­line1 101 ­line2 102 user can press 101 or 102 dialing to line1 or line2 of WellGate 3502 after hearing greeting of WellGate FXO GateWay. -e164 -alias e164 number, which is registered as phone number in gatekeeper. h323 ID, a identification in h323 world for other parties' recognition. The field might be used as a key of authorization or accounting in some VoIP application. It is recommended to assign a special name, or it might conflict with other devices. Switch ON or OFF gatekeeper discovery function (1 = ON; 0 = OFF). When it's ON, WellGate FXO GateWay will send GRQ with GK ID to default gatekeeper. If the GK ID didn't matched, GW will send GRQ with GK ID in multicast. to allocate RTP port range--NOT RECOMMENDED. This may be used when RTP port range conflicts with Firewall policy. Configure H225 RAS port number manually.(N/A). Configure H225 Signal port number manually.(N/A). to set timer for TTL(Time To Live). WellGate FXO GateWay would send RRQ, with keepAlive, to gatekeeper periodically according to TTL timer. gatekeeper finding port. Port number, which WellGate FXO GateWay uses it to discover a gatekeeper. Default value is 1718. to set WellGate FXO GateWay register mode as terminal or gateway,0 as terminal 1 as gateway. Please notice that if set WellGate FXO GateWay as terminal mode, must set sysconf ­2nddial 1(refer to 5.12). to set default gatekeeper RAS port number. Default value, 1719, is well-known port for RAS communication. to allocate dynamic port range, which WellGate FXO GateWay might be using. response timeout. Max waiting time for 1st response to a new call (1~200). connection timeout. Max waiting time for call establishment after receiving 1st response of a new call (1~20000). -gkdis -rtp -h225 -q931 -ttl -gkfind -gwtype -ras -range -respto -connto 3.2.16 [voice] command 46 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 The voice command is associated with the audio setting information. There are four voice codecs (g.729a optional) supported by WellGate FXO GateWay. ------------------------------------------------------------------------------------------------ 47 FXSO H.323 Gateway User Manual Document Ver.: 177A Release OCT., 2003 Parameters Usage: -print print current voice information and configurations. -send to define packet size for each codec. 20/40/60ms means to send a voice packet per 20/40/60 milliseconds. The smaller the packet size, the shorter the delay time. If network is in good condition, smaller sending packet size is recommended. In this parameter, 20/40/60ms is applicable to G.711u/a law, and G.729a codec, while 30/60/90ms is applicable to G.723.1 codec. -priority codec priority while negotiating with other h323 device. This parameter determines the listed sequence in h.245 TCS message. The codec listed in left side has the highest priority when both parties determining final codec. -volume There are three adjustable value. voice volume stands for volume, which can be heard from WellGate FXO GateWay side; input gain stands for volume, which the opposite party hears. dtmf volume stands for DTMF volume/level, which sends to its own Line1 or Line2. -nscng silence suppression and comfort noise generation setting (1 = ON; 0 = OFF). It is applicable to G.723 codec only. An example is demonstrated below: ------------------------------------------------------------------------------------------------- -mindelay the minimum jitter buffer size. (Default value= 90 ms) -maxdelay the minimum jitter buffer size. (Default value= 150 ms) ------------------------------------------------------------------------------------------------- -echo activate each canceller (1 = ON; 0 = OFF). Note: be sure to know well the application before you change voice parameters because this might cause incompatibility. 3.2.17 [tos] command 48