User manual WELLTECH FXSO GATEWAY H.323 3702A

FXSO GATEWAY User Manual (3701A/02A) Notice © Copyright 2002 Welltech Computer Co., Ltd. All intellectual property rights in this publication are owned by Welltech Computer Co., Ltd. and are protected by Republic of China copyright laws, other applicable copyright laws and international treaty provisions. Welltech Computer Co., Ltd. retains all rights not expressly granted. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by Welltech Computer Co., Ltd. No representation of warranties for fitness for any purpose other than what is specifically mentioned in this guide is made either by Welltech Computer Co., Ltd. or its agents. Welltech Computer Co., Ltd. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. Welltech Computer Co., Ltd. may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time. If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document. If you are unable to locate a copy, please contact Welltech Computer Co., Ltd. and a copy will be provided to you. Unless otherwise indicated, Welltech Computer Co., Ltd. registered trademarks are registered in the Republic of China and other territories. For further information, contact Welltech or your local distributor or reseller. FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 STEPS IN CONFIGURATION ..................................................................................4 1. START UP ................................................................................................................5 1.1 INTRODUCTION......................................................................................................5 1.2 FEATURES AND SPECIFICATION ..............................................................................6 1.3 ACCESSORIES AND EQUIPMENT..............................................................................8 1.4 APPEARANCE.........................................................................................................9 2. HOW TO SETUP AND CONNECT BASICALLY.............................................12 2.1 SYSTEM REQUIREMENT.......................................................................................12 2.2 IP ENVIRONMENT SETTING .................................................................................13 2.2.1 For Windows 2000/NT ................................................................................13 2.3 NETWORK CONFIGURATIONS IN YOUR GATEWAY..................................................15 2.3.1 Static ip address ..........................................................................................17 2.3.2 DHCP mode ................................................................................................19 2.3.3 PPPoE mode ...............................................................................................20 2.4 MAKING A VOIP CALL ........................................................................................22 2.4.1 Configure the gateway into the Peer-to-Peer mode....................................22 2.4.2 Configure the gateway into the GK routed mode........................................26 2.4.2.1 The type in GK routed mode ....................................................................27 3. ADVANCED ...........................................................................................................30 3.1 IP SHARING .........................................................................................................30 3.2 NETWORK INTERFACE .........................................................................................34 3.3 H323 CONFIGURATION........................................................................................36 3.4 LINE ....................................................................................................................39 3.5 SYSTEM CONFIGURATION....................................................................................41 3.6 VOICE SETTING ...................................................................................................44 3.7 PHONE PATTERN ..................................................................................................46 3.8 TONE SETTING ....................................................................................................47 3.9 SUPPORT FUNCTIONS...........................................................................................48 3.10 PHONE BOOK ....................................................................................................49 3.11 PREFIX CONFIGURATION ...................................................................................51 3.12 ROUTING TABLE................................................................................................54 3.12.1 Change the default routing .......................................................................55 3.12.2 Add a new Routing Table ..........................................................................57 3.13 FXO PASSWORD................................................................................................59 3.14 IP PACKET TOS..................................................................................................60 Copyright (c) 2002 Welltech Computer Co. Ltd. 1 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3.15 DDNS CONFIGURATION....................................................................................61 3.16 RTP PAYLOAD TYPE CONFIGURATION...............................................................62 3.17 VERSION AND INFORMATION .............................................................................63 3.18 PASSWORD ........................................................................................................64 3.19 ROM UPGRADE ................................................................................................65 3.20 FLASH CLEAN ...................................................................................................69 3.21 COMMIT ............................................................................................................70 3.22 REBOOT SYSTEM...............................................................................................71 4. COMMAND LIST .................................................................................................72 4.1 HYPER TERMINAL SETTING.................................................................................73 4.2 COMMAND LIST ..................................................................................................76 4.2.1 [help]...........................................................................................................76 4.2.2 [quit] ...........................................................................................................77 4.2.3 [debug]........................................................................................................77 4.2.4 [reboot] .......................................................................................................77 4.2.5 [flash]..........................................................................................................78 4.2.6 [commit]......................................................................................................78 4.2.7 [ifaddr]........................................................................................................79 4.2.8 [time]...........................................................................................................81 4.2.9 [ping] ..........................................................................................................81 4.2.10 [sysconf]....................................................................................................81 4.2.11 [h323]........................................................................................................85 4.2.12 [line] .........................................................................................................88 4.2.13 [route] .......................................................................................................91 4.2.14 [prefix] ......................................................................................................94 4.2.15 [pbook]......................................................................................................95 4.2.16 [voice] .......................................................................................................97 4.2.17 [support] ...................................................................................................99 4.2.18 [phone]....................................................................................................101 4.2.19 [tone].......................................................................................................103 4.2.20 [fxopwd]..................................................................................................105 4.2.21 [record] ...................................................................................................106 4.2.22 [tos]......................................................................................................... 114 4.2.23 [ddns]...................................................................................................... 114 4.2.24 [pt] .......................................................................................................... 116 4.2.25 [rom] ....................................................................................................... 116 Copyright (c) 2002 Welltech Computer Co. Ltd. 2 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 4.2.26 [passwd].................................................................................................. 118 Copyright (c) 2002 Welltech Computer Co. Ltd. 3 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Steps in configuration STEP 1 Start Up To check out the peripheral equipments and understand the feature of this gateway. Please read this step very carefully before starting the configuring. Connecting the gateway and computer to start configuring by WEB GUI. STEP 2 How to Setup and Connect basically Setting the ip address for this gateway to make sure that it could connect with the internet. Setting the configurations of dialing, including the Peer-To-Peer, GK mode and how to set these tables to make calls by this gateway easily. The other configurations of make call will be discussed in this step. STEP 3 Advanced Advanced configurations and special functions of this gateway. Using the WEB GUI to show how to set this table and explain the meaning of these tables. STEP 4 Command List To explain the meaning of the command in the command line interface and example the usage of the command. To get more usages or configuration in this step and study about the command line configuration. Copyright (c) 2002 Welltech Computer Co. Ltd. 4 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 1. Start Up 1.1 Introduction WellGate 3701A/3702A is a one-port/two-port FXS+FXO gateway. It supports an innovative intelligent call rouging function that transparently routes calls to destination either through PSTN or Internet. WellGate 3701A/3702A provides voice over IP and FAX over IP services for ITSP/ISP Internet Telephony Services Provider and Office/SOHO IP-PBX application. Application Architecture PBX Extension port FXO IP Network FXS FXS FXS FXS FXO Trunk side PBX Extension FXO ports can connect with PSTN Line or Extension Line of PBX FXS ports can connect with Phone Set or Trunk Line of PBX Copyright (c) 2002 Welltech Computer Co. Ltd. 5 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 1.2 Features and specification Features ITU-T H.323 v2/v3/v4 compliance Automatically Dial Path Selection (IP or PSTN) PSTN Line switch to telephone set when power is failure PPPoE support Behind NAT router or IP sharing device DNS server inquiry Automatically Gatekeeper Discovery Provide Peer-to-Peer Mode (Non Gatekeeper needed) selection E.164 Dial Plan TFTP/FTP software upgrade Remote configuration/ reset LED indication for system status MS-NetMeeting v3.0 compatible Support Fix IP and DHCP Parameters of VoIP packet Audio feature Codec -- G.711 a/law, G.723.1 (6.3kbps), G.729, G.729A G.168/165-compliant adaptive echo cancellation Dynamic Jitter Buffer Completed voice band signaling support Provide In-band or Out-band DTMF generation/detection Provide call progress tone Management Feature - TELNET/Console port and Web Browser configuration Certification - UL, CE, FCC FXS Features Copyright (c) 2002 Welltech Computer Co. Ltd. 6 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 - 2-wire loop start Programmable On-Hook voltage, Ring voltage/Cadence/Frequency, Loop current Line polarity reversal generation FXO Features - 2-wire loop start - Support auto-attendant (Tone or voice greeting) - PSTN polarity reversal detection - Provide 2nd dial tone to PSTN - Disconnect tone detection - Asking ping function with the inside or outside calls Environmental Operation temp:0°C to 40°C Humidity: 10% to 90% (Non-condensing) Copyright (c) 2002 Welltech Computer Co. Ltd. 7 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 1.3 Accessories and equipment The voice gateway in 2/4 FXS ports models and two RJ-45 connector (WAN and LAN). The AC adapter. The CD of user manual. The connection cable in RS-232 interface. Copyright (c) 2002 Welltech Computer Co. Ltd. 8 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 1.4 Appearance Front panel: The LED lights provide related system messages of the gateway. WellGate 3701A WellGate 3702A Power: Light on means Gateway is power on, and vice versa. TEL: Light on means the line is in use (off-hook), and vice versa. LINE: Light on means the line is in use (off-hook), and vice versa. Status: 1. LED light on means Gateway has successfully registered to Gatekeeper when it is in Gatekeeper Mode. 2. LED flash means Gateway is not registered to Gatekeeper when it is in Gatekeeper Mode. 3. Or when Gateway is in downloading mode, LED should be flash as well. 4. LED light off means Gateway is in Peer-to-Peer Mode. Ready: 1. Light on and slow flash means Gateway is in normal mode. 2. Light on and fast flash means Gateway is in downloading mode. WAN: Connected to Public Ethernet 1. Line- LED light on means Gateway is physically connected to the Ethernet correctly. 2. ACT- LED light on and flash when Ethernet data is being transmitted / received. LAN: Switch to another device, such as PC 1. Line- LED light on means Gateway is physically connected to the Ethernet Copyright (c) 2002 Welltech Computer Co. Ltd. 9 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 correctly. 2. ACT- LED light on and flash when Ethernet data is being transmitted received. Back panel: WellGate 3701A WellGate 3702A 1. Ethernet Port LAN/WAN: 10/100 Base-T; RJ-45 socket, complied with ETHERNET 10/100base-T. The pin-out is as following: PIN 1, 2: Transmit PIN 3, 6: Receive 2. COM: RS232 console port (DB-9pin male connector) Note: use straightforward cable to connect to your computer. Copyright (c) 2002 Welltech Computer Co. Ltd. 10 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 PINOUTS Pin Name Dir 2 3 5 RXD TXD GND Description Receive Data Transmit Data System Ground 3. TEL: RJ-11 connector, FXS interface is for connecting the analog phone sets or trunk line of PABX. 4. LINE: RJ-11 connector, FXO interface is for connecting the extension line of PABX or PSTN Line. 5. 12V DC: Input AC 100V~120V;output DC12V. Copyright (c) 2002 Welltech Computer Co. Ltd. 11 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 2. How to Setup and Connect basically 2.1 System Requirement 1. One PC (a) Pentium 100 or above, 64 RAM, Windows 98 or above. (b) Ethernet card or COM port 2. One standard straightforward RS-232 cable (female connector to Gateway side). 3. Analog telephone sets. 4. PBX extension Lines or PSTN Lines. 5. Software tools (a) Hyper Terminal, TELNET, Web Browser. (b) Gatekeeper (optional). Copyright (c) 2002 Welltech Computer Co. Ltd. 12 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 2.2 IP Environment Setting User must prepare a valid IP address, complied with IP Network, for Gateway's proper operation. For testing the validation of chosen IP address, using the same IP configuration in other PC or Notebook, and then try to connect to Public Internet (go to well-known website, receive Internet mail, or ping a specific public IP address). If it works, use the same IP address and network configuration for Gateway. Please follow up the step for the configuration of your computer or notebook. 2.2.1 For Windows 2000/NT Please make sure that the network interface of your computer is working fine and the cross over line (RJ-45) is connecting with the computer correctly or you could use a hub to connect with your computer and this gateway. Turn on your computer and configure the network parameter as follow: 1 Go to the start menu and enter the setting area. Click control panel. 2 Enter the network configuration. Copyright (c) 2002 Welltech Computer Co. Ltd. 13 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Figure 2.1: Network Configuration 3 Select the Property of the LAN card. 4 Setup the ip address, subnet mask and default gateway as below: Figure 2.2: Configure the network 5 Click OK after you finished the network setup. Copyright (c) 2002 Welltech Computer Co. Ltd. 14 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 The default ip address, netmask and default gateway address of the gateway is 10.1.1.3, 255.255.0.0, 10.1.1.254. 2.3 Network configurations in your gateway 1 Key in the ip address of the gateway (http://10.1.1.3) with the browser Copyright (c) 2002 Welltech Computer Co. Ltd. 15 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 2 After key in the ip address, you have to enter the user name and password to enter the WEB configuration. (Username: root ; No password) Figure 2.3: Login the username and password 3 You will enter the main page of the configuration after key in the login name and password correctly: Copyright (c) 2002 Welltech Computer Co. Ltd. 16 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Figure 2.4: The main WEB configuration 4 Press the Network Interface to configure the networking of your gateway: Figure 2.5: The Network Interface 2.3.1 Static ip address 1 Please get the correct ip address, netmask and default gateway address from your ISP first. Press the OK button if you finished. Copyright (c) 2002 Welltech Computer Co. Ltd. 17 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Figure 2.5: Configure the static ip address 2 Press the commit if you finish the configuration. Figure 2.6: Commit the data 3 Press the reboot if you want the configuration executed. Copyright (c) 2002 Welltech Computer Co. Ltd. 18 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Figure 2.7: Reboot the system 2.3.2 DHCP mode 1 Change to the DHCP mode if you are using the cable modem or DHCP server. Figure 2.8: Enable the DHCP function Copyright (c) 2002 Welltech Computer Co. Ltd. 19 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 2 Please commit the data and reboot the machine after you enable the DHCP function. 2.3.3 PPPoE mode 1 Chang the PPPoE mode in the IP mode table. Figure 2.9: Chage to PPPoE mode 2 Please commit the data and reboot the machine after you finished the configuration of PPPoE. Copyright (c) 2002 Welltech Computer Co. Ltd. 20 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Figure 2.10: Enter the PPPoE connection info Copyright (c) 2002 Welltech Computer Co. Ltd. 21 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 2.4 Making a VoIP Call There are two modes that you could configure the gateway for making VoIP calls. One is the Peer-to-Peer mode, another is GK routed mode. The configurations and functions are different. Please make sure about the mode you want and follow up the step to configure your gateway. 2.4.1 Configure the gateway into the Peer-to-Peer mode 1 Enter the H323 Configuration table and change the mode to Peer-to-Peer. Figure 2.10: Configure the Peer-to-Peer mode 2 Press the OK button which is on the buttom of this page to save the configuration. Figure 2.11: Press OK to save the data Copyright (c) 2002 Welltech Computer Co. Ltd. 22 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3 Enter the Phone Book configuration table and configure the name, ip address and phone number of the destination. Figure 2.12: Phone Book Copyright (c) 2002 Welltech Computer Co. Ltd. 23 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Example Figure 2.13: The example of Phone Book configuration The name of the destination: test The E164 number (phone number) of the destination: 123 The ip address of the destination: 10.1.1.100 The call signal port of the destination: 1720 (The port will be 1720 if you don' t define it) Drop prefix: Enable ­ The e164 number you define will be deleted Disable ­ The e164 number you define will be kept Insert prefix: To add a number you define in this table Press the "Add Data" button when you finished, and the new table will display on the first index if you press the Phone Book configuration button. 4 Please Commit it and Reboot the system if the configuration is finished. Copyright (c) 2002 Welltech Computer Co. Ltd. 24 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Figure 2.14: To show the Phone Book record Phone Book is only for the Peer-to-Peer mode. Fifty index support. The application in the drop and insert function Input (E164) 100 200 300 400 Drop Disable Disable Enable Enable Insert X 0 X 500 Output 100 0200 X 500 X ­ Do not enter any numbers Copyright (c) 2002 Welltech Computer Co. Ltd. 25 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 2.4.2 Configure the gateway into the GK routed mode 1 Enter the H323 Configuration table and change the mode from Peer-to-Peer to GK routed. To change the GK information from your service provider (Ex: The Gatekeeper IP, Registered Prefix and Registered Alias). Figure 2.15: Configure the GK info 2 Press the OK button which is on the buttom of this page to save the configuration. Figure 2.16: Press OK to save the data 3 Press the Commit Data and Reboot System buttons when you finished the configuration. Copyright (c) 2002 Welltech Computer Co. Ltd. 26 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 2.4.2.1 The type in GK routed mode There are two types in the GK routed mode you could choose. One is Gateway type and another is Terminal type. There are some different functions, applications and configurations between the Gateway type and Terminal type. Please get more info from the table as below: Gateway Type Prefix number is necessary The E164 number of each port should be follow the prefix number Support the one-stage dialing Terminal Type Prefix number is not necessary The E164 number of each port could be different Do not support the one-stage dialing The default type of the all series Welltech gateway are Gateway type. But the LanPhone is the terminal type. You could change the type for your gateway but the LanPhone couldn't. Please pick up the type you want to use with your gateway and pay more attentions about the rules as above. There are two example for the Gateway type and Terminal type as below: Copyright (c) 2002 Welltech Computer Co. Ltd. 27 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Example ­ Gateway type Figure 2.17: Gateway Type configuration The prefix number is necessary if you configure it to be a gateway. The number of ports must be followed the prefix number. Example ­ Terminal type Copyright (c) 2002 Welltech Computer Co. Ltd. 28 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Figure 2.18: Terminal Type configuration The prefix number is only for the gateway type and the number of ports could be configured in the different numbers. Copyright (c) 2002 Welltech Computer Co. Ltd. 29 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3. Advanced There are too many advanced commands for the advanced users. The following chapters are based on the application layer. Please get the info what you need. If you need the command, please watching the chapter of Command Line Interface. 3.1 IP Sharing The function is only for the user who is using the IP Sharing device. It is said Gateway is connected to the IP Sharing device. The IP Sharing Device must support the DMZ or Virtual server functions An example such as ADSL network is in the following. ATU-R ADSL Modem WAN IP Sharing device LAN LAN Gateway PC The WAN IP Address obtained from ADSL has two kinds of methods. One is fixed IP Address, while user applies for one or more fixed IP Addresses. Another is dynamic IP Address while user applies for dial-up connection way. Copyright (c) 2002 Welltech Computer Co. Ltd. 30 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 The LAN IP Address of User's PC can be set as DHCP client in order to gain a valid one. Another IP Address for Gateway must be set as an fixed one in order for that IP Sharing device pass forwarding the relevant information from WAN to LAN. Besides, a valid IP Address meets the IP Sharing device (LAN site) is the element. Please configure your gateway just like below: 1 Enter the IP address, Netmask and the default gateway in the network table. Please follow up your IP Sharing device. Figure 3.1: Network configuration 2 Enable the ip sharing function and put the static ip address in the server address table. Copyright (c) 2002 Welltech Computer Co. Ltd. 31 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Figure 3.2: Enable the ip sharing function 1. Fixed IP ­ Please put the ip address of the ip sharing device in the IP Sharing Server Address table. 2. Dynamic IP ­ Just leave it if the IP sharing device is using PPPoE or DHCP protocol to connect with the internet. 3 The IP change function is only for the special usage Figure 3.3: IP Change IP Change Function: The ip address of the IP Sharing Server Address will use what you configured in that table if you disable the IP Change function. 32 Copyright (c) 2002 Welltech Computer Co. Ltd. FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 It supports the static ip address. If user is using the dynamic ip address, this function has to be enabled. If the wan port of the ip sharing device is using the dynamic ip address, the gateway couldn't get the ip address if the GK isn't from ours, too. 4 Please Commit it and Reboot the system if the configuration is finished. This chapter is focus on the DMZ function of the IP Sharing Device, Please get another application from our web site. Copyright (c) 2002 Welltech Computer Co. Ltd. 33 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3.2 Network Interface User could configure the networking environment in this web page or change some default setting for networking. Please get more info from the following description. (see figure 3.4) Figure 3.4: Network Interface IP Mode ­ Users could define the networking type for this gateway. It could support the Static, DHCP and PPPoE function. IP Address ­ Define the ip address for your networking if it is the fixed ip. Please get this info from your ISP. Subnet Mask ­ Define the mask address for your networking. Please get this info from your ISP. Default Gateway ­ Define the default gateway for your networking. Please get this info from your ISP. HTTP Port ­ This port is for the WEB configuration. The default port for the WEB is users could change it by this table. DNS primary ­ Users could define the primary DNS server address. DNS secondary ­ Users could define the primary DNS server address. SNTP ­ Enable the SNTP server registering function if user wants to get 34 Copyright (c) 2002 Welltech Computer Co. Ltd. FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 the correct time from the Command Line Interface. SNTP Server Address ­ Enter the correct ip address of the SNTP server or get the incorrect time from the Command Line Interface. GMT ­ Configuring the time area for the time display in the Command Line Interface. IP Sharing ­ Enable this function if the gateway is behind the IP sharing device. IP Sharing Server Address ­ Enter the WAN IP address of the IP sharing device if it is the fixed ip. IP Change ­ Enable this function if the WAN IP address of the IP sharing device is dynamic address. The IP change function could support the GK from Welltech only. Please pay more attentions about this function if your IP sharing device is using the dynamic IP address. PPPoE User Name ­ Put the PPPoE connection account in this table. Please get this info from your ISP. PPPoE Password ­ Put the PPPoE connection password in this table. Please get this info from your ISP. PPPoE IP Address ­ After the connection success, this table will show you the IP address which the gateway got from the ISP. PPPoE Destination ­ After the connection success, this table will show you the default gateway address, which the gateway got from the ISP. PPPoE DNS primary ­ After the connection success, this table will show you the DNS ip address from the ISP. Reboot After Remote Host Disconnection ­ Enable this function will make the gateway restart automatically if the PPPoE connection is disconnected or the IP address was taken back by the ISP. Copyright (c) 2002 Welltech Computer Co. Ltd. 35 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3.3 H323 Configuration This page could support user configure the info about GK or change the mode from GK mode to Peer to Peer mode. Please get more detail info from below. (see figure 3.5) Figure 3.5: Network Interface Mode ­ Change the mode for this unit using. GK routed : Users have to registered on the GK if users picked up this option. Peer-to-Peer : It only supports the peer-to-peer mode and users have to define the phone book for this mode. Gatekeeper IP Address ­ Enter the GK ip if users pick up the GK routed mode. Support the GK mode only. 2nd Gatekeeper IP ­ It's for the back up using. Gateway will send RRQ to this GK if didn't receive the RCF from the First GK about one minute. Support the GK mode only. Default Gateway IP ­ All the calls will be routed to this destination if the destination couldn't be found in the Phone Book configuration. Support the Peer-to-Peer mode only. 36 Copyright (c) 2002 Welltech Computer Co. Ltd. FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Gateway Type ­ Pick up the type for gateway. Support the GK mode only. Gateway : Could support one-stage-dialing function. Terminal : Couldn't support one-stage-dialing function. Registered Prefix ­ The phone number for the GK registering. Support the GK mode only. Line1 (TEL 1) Number ­ Configure the number for the 1st FXS port. Line2 (TEL 2) Number ­ Configure the number for the 1st FXO port. Line3 (TEL 3) Number ­ Configure the number for the 2nd FXS port. Line4 (TEL 4) Number ­ Configure the number for the 2nd FXO port. Registered Alias ­ The name of this gateway for the GK registering. Support the GK mode only. Display Information ­ For the display name in the packets. Gatekeeper Discovery ­ Gateway will send the GRQ message and it will register on the GK if it had received the GCF message. When users enable this function, the GK name is necessary for this. User could enable this function first and define the name of the GK. Gateway will send the GRQ message by broadcast if users define the IP address of GK is 255.255.255.255. If the gateway receive GCF message that's meaning the GK accept the request from gateway, so the gateway could register on that GK successfully who reply the GCF message. Gatekeeper ID ­ The name of the GK. It has used with the Gatekeeper Discovery function. Support the GK mode only. RTP Port ­ The UDP port for the voice sending. RTP ports support a range of the UDP. The line 1 is using UDP(RTP) 16384 and (RTCP) 16385. The line 2 is using UDP(RTP) 16386 and (RTCP) 16386....etc. This configuration is defining the start port for the RTP packets. Support the GK and Peer-to-Peer mode both. From 1024 to 65535. Time To Live(TTL) ­ The time for the registered confirm. Support the GK mode only. From 0 to 3600. Gatekeeper finding port ­ The port for the Gatekeeper Discovering function for this gateway. Support the GK mode only. From 1024 to 65535. Gatekeeper RAS Port ­ The GK registering port of this gateway. Support the GK mode only. From 1024 to 65535. H225 RAS Port ­ The RRQ sending port of this gateway. Support the GK mode only. From 1024 to 65535. H225 Call Signal Port ­ The Call Signal Port sending of this gateway. 37 Copyright (c) 2002 Welltech Computer Co. Ltd. FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Support the GK and Peer-to-Peer mode both. From 1024 to 65535. Destination H225 Call Signal Port ­ The destination Call Signal Port. Support the GK and Peer-to-Peer mode both. From 1024 to 65535. Allocate Port Range Start ­ The port range for this gateway. From 1024 to 19999. Allocate Port Range End ­ The port range for this gateway. From 1024 to 19999. Response Timeout ­ The call will be timed out if the call proceeding message didn't received from the remote side. Support the GK mode only. From 1 to 200. Connection Timeout ­ The call will be timed out if the connect message didn't received from the remote side. Support the GK mode only. From 1 to 20000. H.235 Security Token ­ Support H235 security password for the registration. Copyright (c) 2002 Welltech Computer Co. Ltd. 38 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3.4 Line The Line configuration will show the status of the registrations and the ports. It includes the hunt group, hotline, and no answer forward configuration. Press the Line configuration button to enter configuration table (see figure 3.6) Figure 3.6: Line Configuration Type ­ Show the type of this port. There are only two types of this gateway. One is FXS type another is FXO type. It couldn't be changed. Hunting Group ­ Define the group number of this port. When the port is busy, the call could be transferred to another port in the same group. Only the same type could be configured in the same group. Hotline ­ Enable or Disable the hotline mode. The hotline mode will be enabled if you enter the hotline number. The default setting is disabled. No Answer Forward ­ When the port didn't answer the call, this call will be forwarded to the number you configured. This is only for the E164 number or the phone number you want to transfer. This function should be used with the forwardtime command (in the System configuration table). The range of the forward time is 5 to 65535. If the function is enable, the No Answer forward number is 123, and the forward time (c) 5 Welltech Computer call forwarded to the destination with 123 Copyright is 2002seconds. TheCo. Ltd. will be 39 numbers when the origin port didn't answer the call. FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Registration ­ To show the gateway registered on the GK or not. Status ­ To show the port is busy or ready. Copyright (c) 2002 Welltech Computer Co. Ltd. 40 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3.5 System Configuration Figure 3.7: System Configuration Keypad Type ­ User could define the keypad for the DTMF sending. In-Band : The DTMF signal sending by RTP. Out-Band : The DTMF signal sending not by RTP. Including the H.245(Alpha), H.245(Signal), Q.931 and RFC 2833. Inter Digit Time ­ The call will be sent out if user didn't enter the digits after this timer. From 1 to 10. Forward time ­ It supports the No Answer Forward function. If users configure it for 10, the call will be forwarded when it rings about 10 seconds. From 5 to 65535. Prefix ­ This will be added in the first digits of the numbers that users had dialed. Prefix Switch ­ Users could enable or disable this function. Prefix Disable Digits ­ Users could enter this digits for disable this function in this dialing. The Prefix, Prefix Switch and Prefix Disable Digits is a function. Users have to configure these three tables if this function is needed. Copyright (c) 2002 Welltech Computer Co. Ltd. 41 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Ring Time ­ It for the ring detection from the PSTN. The ring detection will be failed if users configure it too long. Ring Before Answer ­ This will help the users to answer the calls from PSTN into this gateway quickly. The call will be connected by one time ring if users configure this for 1. From 1 to 10. Codec Select Method ­ This could support that the codec will follow the MSD (MasterSlaveDetermination) or the caller side. Master : Follow the result from the MasterSlaveDetermination. Caller : Follow the caller side. It's only for the special requirement. Please contact with your vendor before you configure this. Local Generate Ring Back Tone ­ To enable or disable the ring back tone generation from the local side. End of Dial ­ To enable or disable the end of dial function. This function key will be the digit "#". Gateway Prefix ­ To keep or drop the prefix number of this gateway. This only support the Gateway type in the GK routed mode. Please get more detail useful as below : The gateway could keep or drop the prefix number if the call is coming from the ip side and bring the prefix number of this gateway. The usage of this command is about the one-stage-dialing function. Of course it must work with the Routing table. Source 10012345 10012345 Gateway Prefix Keep Drop Receive 10012345 10012345 Transfer 10012345 12345 If the incoming call (From IP side) with the number is 10012345, and the prefix number of the destination gateway is 100. The gateway will receive 10012345. But the number it transfer will be 10012345 (Gateway Prefix Keep). The transfer number will be 12345 if the Gateway Prefix function is enabled. FXO type ­ Users could configure all the calls need the 2nd stage dialing or not. 42 Copyright (c) 2002 Welltech Computer Co. Ltd. FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 Normal : The 1st or 2nd stage dialing will depend on the dialing plan from the users. If user dial the number of the FXO port, that will be the 2nd stage dialing. Force 2nd dial : Every calls will need the 2nd stage dialing type. Hardware Type ­ This will show the hardware detection type. Copyright (c) 2002 Welltech Computer Co. Ltd. 43 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3.6 Voice Setting Users could configure the voice codec or gain level in this web page. Please get more detail info from the following description. (see figure 3.8) Figure 3.8: Voice Setting Codec Priority ­ This could help users configure the codec priority for using. Please pay more attentions about the firmware you use. If the firmware only support G.729 series codec, the G.723 codec in this table will be useful. Frame Size ­ To configure the packet size for the codec that users want. G723 Silence Suppression ­ To enable the VAD and CNG function for the G.723 codec. Line1 (TEL 1) Volume ­ To configure the output gain (voice), input gain (input) and DTMF gain (DTMF) of the first FXS port. Line2 (LINE 1) Volume ­ To configure the output gain (voice), input gain (input) and DTMF gain (DTMF) of the first FXO port. Line3 (TEL 2) Volume ­ To configure the output gain (voice), input gain (input) and DTMF gain (DTMF) of the second FXS port. Line4 (LINE 2) Volume ­ To configure the output gain (voice), input gain 44 Copyright (c) 2002 Welltech Computer Co. Ltd. FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 (input) and DTMF gain (DTMF) of the second FXO port. Echo Canceller ­ To enable or disable the echo cancellation function. Jitter Buffer ­ TO configure the Min or Max delay for the Jitter Buffer. The min is from 0ms and the max is 150ms. Copyright (c) 2002 Welltech Computer Co. Ltd. 45 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3.7 Phone Pattern This WEB will show the tone generation value from this unit. Please don't configure it if you got some correct value for sure. (see figure 3.9) Figure 3.9: Phone Setting Ring Cadence ­ TO configure the frequency and cadence for the local ring tone. The cadence is for ms. Ring Back Tone ­ To configure the value of the local ring back tone generation Busy Tone ­ To configure the value of the local busy tone. Dial Tone ­ To configure the value of the local dial tone. 2nd Dial Tone ­ To configure the value of the local 2nd dial tone. Flash Frequency ­ To configure the High and Low frequency for the Flash sending. Copyright (c) 2002 Welltech Computer Co. Ltd. 46 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3.8 Tone Setting Users could configure the tone pattern of the gateway in this page. If the disconnect tone from PSTN side is match the one of the Busy tone table, the call will be dropped. (see figure 3.9) Figure 3.10: Phone Setting Disconnect Tone ­ To configure the frequency, level gain and on/off time for the busy tone from PSTN side. The busy tone supports 4 tables. Remote Ring Back Tone ­To configure the frequency, level gain and on/off time for the ring tone from PSTN side. The gateway won't connect the calls if the ring tone value is incorrect. Dial Tone ­ To configure the frequency, level gain and on/off time for the dial tone. Ring Back Tone ­ To configure the frequency, level gain and on/off time for the dial tone. Copyright (c) 2002 Welltech Computer Co. Ltd. 47 FXSO H.323 Gateway User Manual Document Ver.: 2.2 Release Mar., 2004 3.9 Support Functions This gateway support the FAX over IP, fast start function and others function. Please enable or disable these in the Support WEB page. (see figure 3.10) Figure 3.11: Support Functions T.38 FAX ­ Enable this function to support the FAX function. T.38 ECM ­ This function could support the error correction mode during the high-speed function. T.38 FAX ASN.1 Support ­ Support the ASN.1 function. Fax Redundancy depth ­ This support function could make the data for the FAX sending for twice. But this will take more bandwidth. Fast Start ­ Enable this function will support the Fast start function. H.245 Tunneling ­ Enable or disable the Tunneling support. H.245 after faststart ­ Enable or disable the H.245 after fast start function. Early H.245 ­ Copyright (c) 2002 Welltech Computer Co. Ltd. 48