LAN Phone 101 User Manual Guide Document Ver. 1.5 Notice © Copyright 2002 Welltech Computer Co., Ltd. All intellectual property rights in this publication are owned by Welltech Computer Co., Ltd. and are protected by Republic of China copyright laws, other applicable copyright laws and international treaty provisions. Welltech Computer Co., Ltd. retains all rights not expressly granted. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by Welltech Computer Co., Ltd. No representation of warranties for fitness for any purpose other than what is specifically mentioned in this guide is made either by Welltech Computer Co., Ltd. or its agents. Welltech Computer Co., Ltd. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. Welltech Computer Co., Ltd. may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time. If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document. If you are unable to locate a copy, please contact Welltech Computer Co., Ltd. and a copy will be provided to you. Unless otherwise indicated, Welltech Computer Co., Ltd. registered trademarks are registered in the Republic of China and other territories. For further information, contact Welltech or your local distributor or reseller. Welltech Computer Co., Ltd. 13F-4, No.150, Jian-Yi Road, Chung-Ho City, Taipei, Taiwan 235, R.O.C. Tel: +886-2-82265699 Fax: +886-2-82265799 E-mail: sales@mail.welltech.com.tw http://www.welltech.com.tw 1 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Chapter 1 Introduction .........................................................................................................................3 Product Description..................................................................................................................4 1.Features and Specification ................................................................................................4 2.Appearance........................................................................................................................7 Chapter 2 Operating Procedure ­ LCD Display Configuration......................................................... 11 1.Initialize LAN Phone 101 ....................................................................................................... 11 2.LCD Configuration .................................................................................................................12 Chapter 3 Advanced Configurations via Telnet .................................................................................18 1. [help] command .....................................................................................................................18 2. [quit] command ......................................................................................................................19 3. [reboot] command ..................................................................................................................19 4. [flash] command ....................................................................................................................19 5. [commit] command ................................................................................................................19 6. [ifaddr] command...................................................................................................................20 7. [time] command .....................................................................................................................21 8. [ping] command .....................................................................................................................21 9. [pbook] command ..................................................................................................................22 10. [sysconf] command ..............................................................................................................23 11. [h323] command ..................................................................................................................24 12. [voice] command..................................................................................................................25 13. [tos] command......................................................................................................................26 14. [tone] command ...................................................................................................................27 15. [support] command ..............................................................................................................28 16. [bureau] command ...............................................................................................................29 17.[rom] command.....................................................................................................................30 18.[passwd] command ...............................................................................................................32 Chapter 4 Upgrade the LAN Phone 101 ............................................................................................33 Download Procedure..............................................................................................................33 1.LCD Panel Control..........................................................................................................33 2.Remote Control: Telnet ...................................................................................................34 2 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Chapter 1 Introduction The Welltech LAN Phone 101 is a full-featured IP-based telephone system, which provides VoIP service on LAN or any IP based environment. By using IP environment for voice communication, company or individual can save lots of expenses and make data and voice network converged. LAN Phone 101 also supports PSTN analog line connection. Therefore, it can perform as the same as traditional POTS (Plain Old Telephone Service). 3 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Product Description 1.Features and Specification Basic Features: 4 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Caller ID: IP side display H323-ID and E.164. Display the count of total call received. Display un-answered call name, number. Show caller's name, number, date. Volume Adjustment: Speaker volume level adjustable. Handset Receiver volume level adjustable. LCD: 2 lines, 24 character Dot Matrix display. Indicator messages of HOLD, MUTE, PSTN, Directed Line 1~10. Display current date and time. Display of call duration. Audio features: 5 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Dial tone, busy tone, call-holding tone and ring-back tone Provide H.245 Outband DTMF message Firmware Upgrade: Firmware version displayed on LCD. Two ways to upgrade firmware: - Download by KEYPAD configuration. - Download by Telnet. Management Features: 6 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 2.Appearance 1.Front View and Keypad function C: Cancel and Clear : Move to left /previous and right/next . OK: Press OK to confirm the modification. Direct Line (DL) Button 1 ­ 10: User press DL button to do speed dial according to phone book data 1-10 (please refer to LCD configuration-Phone Address Book or Advanced Configurations via Telnet-[pbook] command ). Number 1 ­10, * and #: The function is as the same as the general phone set. 7 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Corresponding list of keypad and symbol: 1 2 3 4 5 6 7 8 9 * 0 # "Space" ; "," ; "." ; "!" ; "1" "A" ; " B" ; "C" ; "2" "D" ; "E" ; "F" ; "3" "G" ; "H" ; "I" ; "4" "J" ; "K" ; "L" ; "5" "M" ; "N" ; "O" ; "6" "P" ; "Q" ; "R" ; "S" ; "7" "T" ; "U" ; "V" ; "8" "W" ; "X" ; "Y" ; "Z" ; "9" "-" ; "?" ; "*" "0" "#" MUTE: Mute the voice of MIC and let others can't hear from user in communication. PSTN: Press PSTN to switch LAN Phone 101 as PSTN or IP Phone Mode. In PSTN mode, "PSTN" characters will be displayed on LCD left bottom side, then users can dial out as if standard telephone set in PSTN ; in IP Phone mode , "GK" characters will be displayed on LCD left bottom side. HOLD: To hold a call by H.450 hold function. SPEED: Press SPEED and number (Phone book index) to do speed dial according to phone book data (please refer to LCD configuration-Phone Address Book or Advanced Configurations via Telnet-[pbook] command ). FORWARD: Forward a incoming call to another IP device by H.450 forward function.(please refer to LCD configuration-Indicate Forward Type) MESSAGE and its indicated LED light: When missing the incoming calls, the message LED will be flashing. User can know the information of miss call by pressing the message button. TRANSFER: 1. Transfer a call by H.450 transfer function. Press TRANSFER button in communication and press phone No. which user want to transferred to can transfer this call . 2. Change characters to be capital or lowercase: when press TRANSFER before press letters can switch type of letters. REDIAL: Redial the last outgoing call. + and - : Adjust the voice volume in communication. SPEAKER: Speaking without picking up handset. Note: All function keys mentioned above (except Number 1 ­10, * and # ) are effective only in IP Phone mode. 8 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 2.Back View DC 9V: DC 9V power input outlet LAN: RJ-45 connector, connected directly to the Hub through the straight CAT-5 cable. PC: RJ-45 connector, connected directly to the PC through the straight CAT-5 cable Line: RJ-11 connector, connected directly to the PSTN analog line. Note: There are two LED indicated lights: LINK/ACT and 10/100 for LAN port and PC port. When network status is in normal, LED of LINK/ACT will be flashing; when transmit rate is in 10 mbps/100mbps, LED of 10/100 will light off/on . 3.Specification of connector 1 Ethernet Port Ethernet port is for connecting LAN Phone to network, transmit rate supports 10/100 Base-T. Ethernet connector LAN 9 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 2 RJ11connector RJ11 connector is for connecting LAN Phone with PSTN. RJ11connector 10 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Chapter 2 Operating Procedure ­ LCD Display Configuration 1.Initialize LAN Phone 101 1. When power on the LAN Phone 101, the LCD screen shows as below. Lan Phone System initializing 2. Wait around one minute until the LAN Phone 101 finishes application program initialization. 3. User can see flashing greeting as below: Have a Nice Day 4. Then LAN Phone get into standby mode: IP-Phone GK 10:10:10 AM The main LCD screen would be shown as similar as above. The GK word means the LAN Phone 101 is in GateKeeper Mode, and when LAN Phone is connected to SNTP server, on LCD will show current time from SNTP server. 5. After pressing the PSTN button, the GK word will be replaced by PSTN. Then LAN Phone is in PSTN Mode. Please notice that in PSTN mode user must plug PSTN line in RJ-11 port. IP-Phone PSTN 10:10:10 AM Press or to enter into Configuration Mode and then press OK Bottom. There are ten selections for configuration. 1. Quick Setup(mandatory) 2. Connect Configuration (mandatory) 11 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 3. 4. 5. 6. 7. 8. 9. 10. User Line Number/Name (mandatory) Ring Configuration Indicate Forward Type Message Box Phone Address Book Firmware Upgrade Hardware Test Reboot Note: 1. LCD Panel of LAN Phone 101 is operated manually by moving or on the keypad. Press OK to enter separate configuration menu. Press C to go back to the main menu. 2.LCD Configuration User can set the following 10 configurations manually by operating the commands displayed on LCD. Note: Any configurations that have made for the LAN Phone 101, user has to do Reboot in the selection 10 "Reboot". 1. Quick Setup(mandatory) If it is the first time for user to configure LAN Phone 101 , suggest use this command to complete overall configuration .After finish each step please press ok button , system will save configuration and jump to next step. 1. Choose Connect Type: There are three types to select for LAN Phone 101 to connect to the other devices. They are GK, P2P and FXO. The default mode should be in GK mode. When user would like to connect via P2P mode, the LAN Phone 101 must change as well. Move the "~" symbol by press or on the keypad to select one type . FXO mode is not available in this version yet . 2. Please Enter IP Phone IP: In this configuration mode, user presses the prepared IP Address on the LAN Phone keypad. Please input IP address as format :xxx.xxx.xxx.xxx. Please Enter Subnet Mask IP: User has to press the subnet mask which meets IP Address on the LAN Phone keypad. 4. Please Enter Gateway IP: 12 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 3. Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 User has to press the default gateway IP which meets IP Address on the LAN Phone keypad. 5. Please Enter GateKeeper IP: User has to offer one available Gatekeeper server IP Address and set this IP Address on the LAN Phone keypad. Please Enter SNTP IP: LAN Phone 101 supports that user can assign one SNTP (Simple Network Time Protocol) Server in your country by setting in LAN Phone. User has to offer one available SNTP server IP Address and set this IP Address on the LAN Phone keypad. Choose DHCP (ON/OFF): User can set LAN Phone in DHCP mode, which means LAN Phone will get a dynamic IP automatically. Please Enter LINE NUMBER: User has to identify one number for the LAN Phone 101 to register to the Gatekeeper. Please Enter LINE NAME: User has to identify one ID name for the LAN Phone 101 to register to the Gatekeeper. 6. 7. 8. 9. 10. Please Enter TFTP /FTP IP: User has to offer one TFTP/FTP server IP Address and set this IP Address on the LAN Phone keypad and the IP is necessary for upgrading LAN Phone new version file. 11. Please Enter User Name: User has to press user name for FTP server login .It is necessary for upgrading LAN Phone new version file in FTP method. 12. Please Enter Password: User has to press password for FTP server login .It is necessary for upgrading LAN Phone new version file in FTP method. 13. Please Enter PWD Again: User has to press password for FTP server login again to confirm password. 14. System Will Reboot! Press OK To Continue: If user makes sure each configuration is correct, press OK then LAN Phone will reboot or user can press C to jump out this command. 15. After reboot, user can start to use LAN Phone. 13 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 2. Connect Configuration (mandatory) There are six sub-configurations included in Connect Configuration. It is necessary for user to set it in order to run the LAN Phone 101 correctly. In addition, user has to prepare one valid IP Address to meet your network environment. (Global public IP Address or Virtual IP Address) 1. IP Address In this configuration mode, user presses the prepared IP Address on the LAN Phone keypad, then press ok bottom. Subnet Mask User have to press the subnet mask which meets IP Address on the LAN Phone keypad. Gateway User have to the default gateway which meets IP Address on the LAN Phone keypad, then press ok bottom. Gatekeeper User has to offer one available Gatekeeper server IP Address and set this IP Address on the LAN Phone keypad, then press ok bottom. SNTP configuration (1) SNTP Mode: User can set different time can set SNTP function too be on/off/broadcast, which means LAN Phone will capture current time from SNTP server or not, or broadcast to find a SNTP server and capture current time. (2) SNTP Server:User can specify a SNTP server for LAN Phone to capture current time. (3) Time Zone: User can set time zone according to the location LAN Phone is.For example, in Taiwan the time zone should be set as 8,which means GMT+8.(user can press "*" as "-") Note: If user didn't set SNTP server, on LCD won't display current time. 6. Connecting mode There are three types for LAN Phone 101 to connect to the other devices. They are GK, P2P and FXO. The default mode should be in GK mode. When user would like to connect via P2P mode, the LAN Phone 101 must change as well. 14 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 2. 3. 4. 5. Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 FXO mode is not available in this version yet. 7. DHCP Mode User can set LAN Phone in DHCP mode, which means LAN Phone will get a dynamic IP automatically. 3. User Line Number/Name (mandatory) 1. Line Number User has to identify one number for the LAN Phone 101 to register to the Gatekeeper. Line Name User has to identify one ID name for the LAN Phone 101 to register to the Gatekeeper. 2. 4. Ring Configuration 1. Ring Selection There are three tone styles for LAN Phone 101. Move the "~" symbol by press or on the keypad to select the tone style preferred, then press OK to confirm it. Choose Tone Style: Low Middle High 2. Ring Volume Control User can adjust ring volume by by press or on the keypad to decrease or increase volume. 5. Indicate Forward Type There are two selections to activate or deactivate forward function. After selection please press OK (1).Activate : choose under which situation to forward call to another endpoint. After selection please press OK , then enter LINE NUMBER of another endpoint prepared to forward to. 1. Busy When LAN Phone 101 is in busy status, the incoming call will be directly forwarded to the assigned phone number. No response 15 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 2. Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 When LAN Phone 101 is continuing ringing around 10 seconds, the incoming call will be directly forwarded to the assigned phone number. 3. Unconditional It is included the above two types. Whether the LAN Phone is in which status, it will be automatically forwarded to the assigned phone number. (2).Deactivate : choose under which situation to deactivate forward function. After selection please press OK , then enter LINE NUMBER of the endpoint which is already configured to forward to. Note: The number that user prepares to forward to is E.164 number which is registered on the Gatekeeper. 6. Message Box If there is an unanswered IP call, it will be kept in message box . MESSAGE LED will be flashing until user press MESSAGE to check miss call and re-press MESSAGE to return to main screen. 1. 2. New Call History to see all incoming-call records in message box. to see all records in message box. 7. Phone Address Book 1. Display Display all name and telephone number recorded to the phone address book. 2. 3. 4. Add Add and save name, telephone number and IP address of the phone address book. Edit Edit name, telephone number, and IP address of Phone book. Delete Delete the record in the phone address book. Note: When key in IP address in Pbook table, please do not add 0 before IP address(ex.10.1.1.1 please do not key in 010.001.001.001). 8. Firmware Upgrade 16 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 1. Download method There are two methods to download new rom file, please move the "~" symbol by press or on the keypad to select TFTP or FTP method, then press OK to confirm it. Set File Server IP User has to offer one TFTP/FTP server IP Address and set this IP Address on the LAN Phone keypad. The IP Address is necessary for upgrading Lan Phone new application rom file. Set FTP user account User has to press user name and password for FTP server login .It is necessary for upgrading Lan Phone new application rom file in FTP method. Indicate file name User has to press the file name of new application rom file prepared for upgrading Start Download Press OK to start download new application rom file . Firmware Version Show versions of all rom files and hardware. Note: Download via LCD command can only upgrade new application rom file. 2. 3. 4. 5. 6. 9. Hardware Test LAN Phone 101 supports self-test for the all functions buttons. Please follow the direction from LCD panel to operate and verify it. 10. Reboot (mandatory) It is necessary and important for user to reboot it after any configurations has been made to the LAN Phone 101. 17 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Chapter 3 Advanced Configurations via Telnet After initializing the LAN Phone 101 IP Address setting (please refer to LCD Configuration: 1.Connect Configuration), user can enter into configuration mode via telnet. There are 18 commands listed below. Note: 1.After user enter LAN Phone configuration via telnet, please use login:"root", password:"press enter" to enter command line. 2.Each command user must key-in with lower case, but contents of configurations such as h.323 alias or user name etc, user can set as capital case. 3.User who changes any configuration needs to do the commit command then reboot command. 1. [help] command Type help or man or ? to display all the command lists. The following figure is shown all commands of LAN Phone 101. 18 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 2. [quit] command Type quit/exit/close will logout LAN Phone 101 and Program ­Telnet. 3. [reboot] command After doing commit command, type reboot to restart the LAN Phone 101. 4. [flash] command This command will clean the configuration stored in the flash rom to default value and reboot the LAN Phone 101. Note: After user upgrade new software version , suggested to execute this command to make sure new software work well on LAN Phone 101. Note: To execute the command flash ­clean, all configuration of LAN Phone 101 stored on flash rom will be cleaned. It is authorized for the user whose login name is "root" only. 5. [commit] command Save any changes after configuring the LAN Phone 101. 19 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 6. [ifaddr] command Configure and display the LAN Phone 101 IP information. 1. -ip, -mask, -gate: Set LAN Phone 101 IP Address, subnet mask and default gateway respectively. 2. -dhcp: When DHCP function enables (ifaddr ­dhcp 1), LAN Phone 101 will automatically search DHCP server after execute the commit and reboot command. Note: After LAN Phone catch a dynamic IP address form DHCP server, user can see this IP address on LCD connect configuration. 3. -sntp: When sntp server is available, enable LAN Phone 101 SNTP function and point to sntp server IP address. (ifaddr ­sntp 1 "xxx.xxx.xxx.xxx") 4. ­timezone: User can set different time zone according to the location LAN Phone is.For example, in Taiwan the time zone should be set as 8,which means GMT+8. (GMT-8: ifaddr ­timezone -8) 5.-ipsharing: If LAN Phone 101 is behind a IP-sharing , user can enable IP sharing function and specify public IP address.(ifaddr ­ipsharing 0/1 "public IP address of IP sharing" , 0 for disable and 1 for enable) 20 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 7. [time] command When sntp server is established as well as the sntp function of LAN Phone 101 is enabled, type time command should show the current time what is retrieved from the assigned sntp server. Note: Please refer to the Chapter 4.6 [ifaddr] command to configure sntp server.. 8. [ping] command Command ping can test the IP address which is reachable or not. Usage: ping "xxx.xxx.xxx.xxx(IP address)" The message will display packets transmitting condition or no answer from the IP address. 21 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 9. [pbook] command The command is for Peer-to-Peer Mode use only. Therefore, Welltech VoIP products such as LAN Phone 101 that support Peer-to-Peer Mode are also available to be addressed on the LAN Phone 101 phone book. 1.-print: display phone book data. User can print all data in phone book by command (pbook ­print). Furthermore, user can also print only a section of data by indicate parameter 'start_record' and 'end_record' (pbook ­print "start frefix" "end prefix"). If parameter 'end_record' is omited, only record 'start_record' will be display (pbook ­print "start frefix"). 2.-add: add a new record in phone book table by give a name and e164 number for the Gateway / Terminal IP address . (pbook ­add name "X" ip "xxx.xxx.xxx.xxx" e164 "X") 3. -search: search any record such as ip address, name and e164 addressed on the phone book. 4. -delete: delete a record with index listed in phone book table. (pbook ­delete "index number") 5. -insert: insert an record in specified index of phone book. 6. -modify: modify any record that has addressed to index number. The name, IP address and e164 number should be modified together in one modify command. (pbook ­modify "index" name "X" ip "xxx.xxx.xxx.xxx" e164 "X") Note: Please dial "#" after dial e.164 of pbook . 22 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 10. [sysconf] command This command displays the system information and configuration. 1. -print: display system overall information and configuration. 2. -plan: It is for setting dial numbering plan. While e164 number is three digits, the plan should be set as 3 or 0. The plan 0 is for any positive digits use. 3. ­callalive: Enable or disable auto-disconnection after 10 seconds not receiving packets from remote party(sysconf ­callalive 0/1, 0 for disable and 1 for enable) 4.-keypad:set DTMF type .User can select DTMF type LAN Phone receive and transmit.(sysconf ­keypad 0/1/2/3 , 0 for inband ,1 for H.245 alaphanumaric, 2 for H.245 signal type, 3 for Q.931 user info, 4 for RFC2833.) 5.-idto:set the duration(in second) of two pressed digits in dial mode as timed out. If after the duration user hasn't pressed next number, LAN Phone will dial out all number pressed. 6.-eod:select end of dialing key, e.g set end of dial key as OK button , after finished pressing dialing number then press OK will dial out. (sysconf ­eod 0/1/2/3 , 0 for no end of dial key , 1 for "OK" button , 2 for "#" button , 3 for " " button ) 5.-h450:Enable or disable H.450 related features, which include transfer, hold and forward. 23 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 11. [h323] command 1. ­print: display H.323 stack information and configuration. 2. ­mode: configure LAN Phone 101 as GateKeeper or Peer-to-Peer Mode. Usage:h323 ­mode 0/1(0 for GateKeeper mode ,1 for Peer-to-Peer mode) 3. ­gk: set Main GateKeeper IP address(h323 ­gk "xxx.xxx.xxx.xxx") 4. ­algk:set IP address alternative GateKeeper. If LAN Phone tries to register to main GateKeeper for 10 times but still fail, LAN Phone will try to register to alternative GateKeeper. 5. ­e164: identify one number for the LAN Phone 101 to register to the Gatekeeper (h323 ­e164 "X"). 6. ­e164-x:user can assign other 2 telephone numbers and LAN Phone will has different ring tone according to different called number. For example, 3 users share the same LAN Phone, they can assign phone numbers as 100, 200, 300.(h323 ­e164 100 ­e164-1 200 ­e164-2 300) When user dial 100/200/300, ring tone style of LAN Phone will be low/middle/high. To cancel other phone number, user can use "x".(ex.h323 ­e164-1 x) 7. ­alias: identify ID for the LAN Phone 101 to register to the Gatekeeper(h323 ­alias "X").. 8. ­multi: set GateKeeper auto discovery function on or off. If this function is enabled, Lan Phone will multicast to search a GateKeeper on network without assigned GateKeeper IP address. Usage:h323 ­multi 0/1(0 for off ,1 for on) 9. ­rtp: assign RTP port number(1024-65535) 10. ­ttl:set RAS TTL time(0-3600 second) 11. ­gkfind: assign GateKeeper finding port number(1024-65535) 12. ­ras: assign GateKeeper RAS port(1024-65535) 13. ­range: assign dynamically allocated port range(1500-65535) 14. ­respto: set max waiting time for first response to a new call. After dial phone No. without getting response in max waiting time, user will hear busy tone.(1-200 seconds) 15. ­connto: set max waiting time for call establishment after receiving first response of a new call (1-20000 seconds). Note: 1.Items form 6-12 are for advanced user only. 2.In Peer-to-Peer mode, h323 ­print will only display e164,alias, mode ,RTP port, and allocated port range. 3.In P2P mode, please dial "#" after press IP address(ex.10.1.1.1 please dial 10*1*1*1#) or e.164 of Phone book(Please refer to chapter 3.9 Pbook command). 24 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 12. [voice] command The voice command is associated with the voice codec setting information. 1.-print: display voice codec information and configuration. There are five voice codecs included in LAN Phone 101:G.723.1, G.711u, G.711A, G.729a, G.729. 2. -send: three voice packet size can be configured as 20 ms, 40 ms or 60 ms.(only 30 and 60 ms for G..723) 3. -priority: set codecs priority in order.Please notice that user can set from 1 to 5 codecs as their need, for example, voice ­priority g723 or voice ­priority g723 711a g711u g729a g729 means LAN Phone can support only one codec or five codecs. 4. -volume: There are three types can be adjustable, voice volume, input gain and DTMF volume. 5. -nscng: enable or disable sound compression and comfort noise generation. It is only for codec G.723.1. (0 for off ,1 for on) 6. -echo: echo canceller can be made to each specified port. The default value is on to 6 ports. 7.-mindelay:set minimum delay of jitter buffer(0~150) 8.-maxdealy:set maximum delay of jitter buffer(0~150) 25 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Note: It is for advanced administrator use only. Please ask your distributor before changing any settings of this command. 13. [tos] command This command is for setting IP packet TOS values to determine IP Packets priority on network. 1. -print : display current TOS values configurations. 2. -sigtype : configure TOS type of signaling packets from 0 to 7 3. -rtptype : configure TOS type of RTP packets from 0 to 7 4. -rtcptype : configure TOS type of RTCP packets from 0 to 7 5. -sigdelay : configure signaling packets as normal delay or low delay 6. -rtpdelay : configure RTP packets as normal delay or low delay 7. -rtcpdelay : configure RTCP packets as normal delay or low delay 8. -sigthruput : configure signaling packets as normal throughput or high throughput 9. -rtpthruput : configure RTP packets as normal throughput or high throughput 10. -rtcpthruput : configure RTCP packets as normal throughput or high throughput 11. -sigreliab : configure signaling packets as normal reliability or high reliability 12. -rtpreliab : configure RTP packets as normal reliability or high reliability 26 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 13. -rtcpreliab : configure RTCP packets as normal reliability or high reliability Note: This command won't be functional until network environment can be capable with TOS function. 14. [tone] command LAN Phone 101 is configurable of busy tone, reorder tone, ring tone and dial tone. However, only ring tone and dial tone is functional for now, busy tone and reorder tone are for FXO function in the future. Usage tone ­ringtone1/ringtione2/dialtone "low frequency" "high frequency" "low frequency level" "high frequency level" "low frequency on time" "low frequency off time" "high on time" "high frequency off time"; user must key in 8 sets of number to finish this configuration. If it is single-frequency tone, please set high frequency and related items as 0. Furthermore, unit of on/off time is 1/100 second, and suggest to keep level as default value (8).User can also increase the value of level to increase the volume. 27 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 15. [support] command 1. -print : display current SUPPORT values configurations. 2.-fstart: enable or disable fast start (support ­fstart 0/1 , 0 for disable and 1 for enable.) 2.-tunnel: enable or disable H.245 tunnel function.(support ­tunnel 0/1 , 0 for disable and 1 for enable) 3.-h245fs:set if open H.245 separate channel after fast start or not. (support ­h245fs 0/1 , 0 for open and 1 for not.) 28 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 16. [bureau] command Type bureau to display the commands. 1. -print: display bureau line information and configuration. 2. -hold: set hold tone generation on or off. If other terminals support H.450 hold function, and execute hold function when connecting with LAN Phone 101 , user will hear hold tone from LAN Phone 101. (0 for off ,1 for on) 29 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 17.[rom] command 1. -print: show versions of all rom files. 2. -app,-boot, -dsptest, -dspcore, -dspapp, -rbpcm and -htpcm: upgrade main boot code, main application code, DSP testing code, DSP kernel code, DSP application code, Ring Back Tone PCM file and Hold Tone . 3. -boot2m:to upgrade 2mb rom file, which includes all firmware file mentioned in item 2. Note: 1. After 2mb file download is finished, all configurations might change to default value, user has to configure again. 2. MAC address might change to default value also, please MUST use command setmac: Usage: key in command setmac key in MAC address (which you can see on a label attached at the bottom of LAN Phone )with format: 00 01 a8 00 0x xx (It means to press enter each time after key in two characters.) 4. -s: it is necessary to prepare TFTP/FTP server IP address for upgrading firmware rom file. 5. -f: the file name prepared for upgrading is necessary as well. 6. ­server: specify TFTP/FTP server IP address. It is corresponding to LCD configuration -firmware upgrade-Set file Server IP. 7. ­method: specify download method to be TFTP or FTP(0 for TFTP.1 for FTP) 8. ­ftp: specify user name and password for FTP download method 30 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 For example: User prepares to upgrade the latest app rom file ­ wtlp.103c, the TFTP server is 192.168.4.101. rom ­app ­s 192.168.1.1 ­f lp.109 (If ­server is specified , can just type rom ­app ­f lp.109) Command rom ­print to show current version installed in LAN Phone 101. 31 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 18.[passwd] command For security protection, user has to input the password before entering application user/config mode. Two configurations of login name/password are supported by the system. 1. ­set: set password of "root" users or "administrator" users. (password ­set root/administrator "password") 2.­clean: clean up password restored before, and user can login :"root/adminstrator", password:"press enter". User who requests authorization to execute all configuration commands needs to login with "root". If a user login with "administrator", two commands are not functional: 1. password ­set root: set password of login : "root". 2. passwd ­clean: clean up password restored before, and user can login :"root/adminstrator", password:"press enter". 3. flash ­clean:only "root" users can clean all configurations stored in flash. 4. rom ­boot :only "root" users can upgrade LAN Phone boot rom version. 5. rom ­boot2m : only "root" users can upgrade LAN Phone 2mb firmware. Furthermore, there is permanent login and password for LAN Phone 101: login:"mac", password:"Mac address of Lan Phone(Please refer to label at the back of LAN Phone 101)" 32 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Chapter 4 Upgrade the LAN Phone 101 LAN Phone 101 supports two methods to upgrade the new version released from Welltech Computer Co. Both methods are necessary to prepare the TFTP program on the host PC as TFTP server. After installing TFTP program on one PC and connecting to network, LAN Phone 101 is ready to be upgraded. 1. LCD Panel Control 2. Remote Control: Telnet Download Procedure 1.LCD Panel Control 1.Choose the 8th selection-Firmware Upgrade. Press OK to enter into the sub-selection as below. 2.Download method There are two methods to download new rom file, please move the "~" symbol by press or on the keypad to select TFTP or FTP method, then press OK to confirm it. 3.Set File Server IP User has to offer one TFTP/FTP server IP Address and set this IP Address on the LAN Phone keypad. The IP address is necessary for upgrading Lan Phone new application rom file. 4.Set FTP user account User has to press user name and password for FTP server login .It is necessary for upgrading Lan Phone new application rom file in FTP method. 5.Indicate file name User has to press the file name of new application rom file prepared for upgrading 6.Start Download Press OK to start download new application rom file . 7.Firmware Version Show versions of all rom files. 33 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 Note: Download via LCD command can only upgrade new application rom file. 2.Remote Control: Telnet Associated with the Chapter 3.15 [rom] command: 1. -print: show versions of all rom files. 2. -app,-boot, -dsptest, -dspcore, -dspapp, -rbpcm and -htpcm: upgrade main boot code, main application code, DSP testing code, DSP kernel code, DSP application code, Ring Back Tone PCM file and Hold Tone . 3. -s: it is necessary to prepare TFTP/FTP server IP address for upgrading rom file. 4. -f: the file name prepared for upgrading is necessary as well. 9. ­server: specify TFTP/FTP server IP address. It is corresponding to LCD configuration -firmware upgrade-Set file Server IP. 10. ­method: specify download method to be TFTP or FTP(0 for TFTP.1 for FTP) 11. ­ftp: specify user name and password for FTP download method For example: User prepares to upgrade the latest app rom file ­ wtlp.103c, the TFTP server is 192.168.4.101. rom ­app ­s 192.168.1.1 ­f lp.109 (If ­server is specified , can just type rom ­app ­f lp.109) 34 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07 LAN Phone 101 User Manual Guide Document Ver. 1.5 35 Copyright (c) 2002 WellTech Computer Corporation LAN Phone Ver 109 Release 2002/06/07