User manual WESTINGHOUSE MT25 TILT - INSTALL GUIDE

Installation and Assembly - Flat/tilting wall mount for LCD screen IMPORTANT! Read entire instruction sheet before you start installation and assembly. Maximum Load Capacity: 25 lb (11.4 kg) Model: MT25 TILT R Parts List PART # A 095-4034 B 095-4140 C 504-2013 D 520-2005 E 500-2002 F 590-0097 G 520-2027 H 504-2014 I 590-5003 QTY. 1 1 4 4 2 2 4 4 4 DESCRIPTION wall bracket tilt bracket M4 x .7 x 12 mm phillips screw M5 x 10 mm phillips screw #10 X 1 1/2" wood screw concrete anchor M4 x .7 x 10 mm phillips screw M4 x .7 x 20 mm phillips screw retaining spacer B A C D G H E F I 1 of 5 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 04-16-04 SHEET #: 095-9193-1 For customer service call 1-866-287-5555. Insert two screws (D) into wall bracket (A). A D For Wood Stud Walls use a stud finder to locate center of stud. Drill two 1/8" (3 mm) dia. holes to a minimum depth of 1.5" (64 mm). Attach wall bracket (A) to center of wood stud using two screws (E). WARNING · Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. · Never tighten in excess of 80 in · lb (9 N.M.). · Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended. WOOD STUD WALL E A 2 of 5 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 04-16-04 SHEET #: 095-9193-1 For customer service call 1-866-287-5555. WARNING · When installing wall mounts on cinder block, verify that you have a minimum of 1 5/8" of actual concrete surface in the 1/4" diameter hole to be used for the concrete anchors. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. Do not drill into mortar joints, which are brittle and will not provide a stable anchorage! F For Concrete Walls drill one 1/4" (6 mm) dia. hole to a minimum depth of 1.5" (64 mm). Insert anchor (F) in hole flush with wall as shown (right). Place wall bracket (A) over anchor (F) and secure with #10 x 1.5" wood screw (E). Make sure wall bracket is level, mark other hole and repeat steps with other fasteners. Tighten all fasteners. E A WARNING · Tighten wood screws firmly, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. · Never tighten in excess of 80 in · lb (9 N.M.). 3A concrete wall F WARNING · Never use concrete expansion anchors for attachment of wall plate to concrete walls covered with a layer of plaster, drywall, or other finishing material. Drill hole and insert anchor (F) 3B E A F Place wall bracket (A) over anchor (F) and secure with screw (E) CUTAWAY VIEW 3C After repeating step one tighten all fasteners 3 of 5 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 04-16-04 SHEET #: 095-9193-1 For customer service call 1-866-287-5555. This product is designed to accommodate screens with Vesa® compliant hole pattern. For safe mounting, please make sure that mounting screws turns at least three complete turns in the screen inserts. FOR VESA 75 MOUNTING PATTERN: 1. Choose hole pattern indicated below. 2. Attach tilt bracket (B) to back of screen using four 10 mm screws (G) as indicated below. 3. If hole pattern is in a pocket, attach tilt bracket (B) to back of screen using four 20 mm screws (H) and four retaining spacers (I) as indicated below. FOR VESA 100 MOUNTING PATTERN: 1. Choose hole pattern indicated below. 2. Attach tilt bracket (B) to back of screen using four 10 mm screws (G) as indicated below. Note: If you don't get three complete turns in the screen inserts, use four M4 x 12 mm screws (C) instead of four M4 x 10 mm screws (G). For screens with a hole pattern in a pocket, spacers (I) go between tilt bracket (B) and screen. B B Note: Screen may appear slightly different than illustrated WARNING · The screen and bracket may be too heavy and bulky for one person to handle safely. Two or more persons, or mechanical lifting equipment, should always be used to securely attach the screen to the wall bracket. Refer to your screen's owner's manual for additional installation instructions. Hook tilt bracket (B) onto wall bracket (A). Adjust tilt (15° forward and 5° back) and secure with two M5 screws (D). SCREEN SCREEN D B A Note: Refer to your TV owner's manual for additional instructions which may pertain to the positioning of your specific TV. 4 of 5 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 04-16-04 SHEET #: 095-9193-1 For customer service call 1-866-287-5555. Limited Five-Year Warranty Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the "Product") that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5) years from the date of purchase by the original end-user, subject to the following terms and conditions: REPAIR OR REPLACEMENT ­ For a period of five (5) years from the original date of purchase, Westinghouse Digital Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product. Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90) days from the date of delivery to the end-user, whichever occurs last. OBTAINING WARRANTY SERVICE ­ To obtain warranty services, you must either personally deliver or ship the Product to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at (866) 287-5555 to obtain a Return Merchandise Authorization ("RMA") and for other instructions regarding return and replacement or repair of the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA. EXCLUSIONS TO WARRANTY ­ This warranty does not cover damage caused by (a) service or repairs by anyone other than personnel authorized by Westinghouse Digital Electronics, (b) the failure to utilize proper packing when returning the product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in transit or otherwise. PROOF OR ORIGINAL PURCHASE ­ A sales receipt, invoice, or other proof of purchase specifying the original date of purchase within the five (5) year warranty period must be presented to obtain warranty service. This warranty extends to the original purchaser and is not transferable. EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CLAIMED TO ARISE FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION AND SCOPE TO THE TERMS OF THIS WARRANTY. Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from State to State. Westinghouse Digital Electronics, LLC 16257 East Gale Ave. City of Industry, California 91745 Tel: (626) 333-9677. 5 of 5 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 04-16-04 SHEET #: 095-9193-1 For customer service call 1-866-287-5555. and Westinghouse are trademarks of Westinghouse Electric Corporation and are used under license.