Installation and Assembly: Universal Flat Wall Mount for 22" - 37" Screens Model: MT80 THIN Features: · Universal design for 22" to 37" plasma and LCD screens · Low-profile design keeps the screen close up against the wall Visit the Westinghouse Web Site at www.westinghousedigital.com R Max Load Capacity: 80 lb (36.3 kg) For customer service call 1-866-287-5555. ISSUED: 03-02-05 SHEET #: 201-9323-1 Note: Read entire instruction sheet before you start installation and assembly. WARNING · Do not begin to install your Westinghouse product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer service at 1-800-729-0307. · Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components. · Never exceed the Maximum Load Capacity of 90 lb (40.8 kg). · If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended. · Always use an assistant or mechanical lifting equipment to safely lift and position equipment. · Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power. Tools Needed for Assembly · stud finder ("edge to edge" stud finder is recommended) · phillips screwdriver · drill with 1/4" and 5/32" drill bits Table of Contents Parts List .............................................................................................................................................................................. 3 Installation to Single Wood Stud Wall ................................................................................................................................... 4 Installation to Double Wood Stud Wall .................................................................................................................................. 5 Installation to Solid Concrete or Cinder Block ....................................................................................................................... 6 Installing Flat Panel Screen to Wall Plate ............................................................................................................................. 7 Adding Safety to Mount ........................................................................................................................................................ 7 For customer service call (800) 729-0307 or (708) 865-8870. 2 of 8 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Before you begin, make sure all parts shown are included with your product. Parts List AA BB CC DD EE FF Description Qty wall plate 1 adapter bracket 2 #14 x 2.5" wood screw 4 M5 x .8 x 25 mm socket head cap screw 2 Alligator® anchor 4 4 mm security allen wrench 1 MT80 THIN Part # 200-4629 200-4628 5S1-015-C04 520-9567 590-0097 560-1145 AA BB FF DD EE CC 3 of 8 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Installation to Single Wood Stud Wall WARNING · Installer must verify that the wall will safely support four times the combined weight of all attached equipment and hardware. 1 Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center of studs with pencil. Drill three 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Attach wall plate (AA) using three #14 x 2.5" wood screws (CC). Skip to step 2 on page 7. WARNING · Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. · Never tighten in excess of 80 in. · lb (9 N.M.). · Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended. · Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations. AA CC 4 of 8 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Installation to Double Wood Stud Wall WARNING · Installer must verify that the wall will safely support four times the combined weight of all attached equipment and hardware. 1 Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center of studs with pencil. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Attach wall plate (AA) using four #14 x 2.5" wood screws (CC). Skip to step 2 on page 7. WARNING · Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. · Never tighten in excess of 80 in. · lb (9 N.M.). · Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended. · Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations. AA CC 5 of 8 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Installation to Solid Concrete or Cinder Block WARNING · When installing Westinghouse wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. · Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. · Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components. 1 Use wall plate (AA), making sure that it is level, as a template to mark holes. Drill four 1/4" (6 mm) dia. holes to a minimum depth of 2-1/2" (64 mm). Insert anchors (EE) in holes flush with wall as shown (right). Place wall plate over anchors and secure with #14 x 2.5" screws (CC). Tighten all fasteners. 1 concrete surface EE Drill holes and insert anchors (EE). WARNING · Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power. · Never tighten in excess of 80 in. · lb (9 N.M.). 2 AA CC EE Place plate (AA) over anchors (EE) and secure with screws (CC). 3 WARNING · Always attach concrete expansion anchors directly to load-bearing concrete. · Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. Tighten all fasteners. so lid co nc ret e AA CC EE cin de rb loc k INCORRECT CUTAWAY VIEW wall plate concrete wall plate CORRECT concrete plaster/ dry wall plaster/ dry wall 6 of 8 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Note: Before starting this step refer to accompanying instruction sheet to install adapter brackets to flat panel screen. Installing Flat Panel Screen to Wall Plate 2 Insert two M5 x 25 mm socket head cap screws (DD) into mounting brackets (BB) and tighten a few turns to hold in place as shown in detail 1. Hang screen by the mounting brackets (BB) on wall plate (AA) as shown below. Make sure screen is safely hooked on mount before letting go. Screen can be adjusted horizontally if desired. WARNING · Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. BB BB AA detail 1 Adding Safety to Mount 3 Secure mounting brackets to wall plate (AA) with socket head cap screws as shown below and in detail 1. Tighten screws with 4 mm security allen wrench (FF). BB DD AA DETAIL 1 7 of 8 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Limited Five-Year Warranty Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the "Product") that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5) years from the date of purchase by the original end-user, subject to the following terms and conditions: REPAIR OR REPLACEMENT ­ For a period of five (5) years from the original date of purchase, Westinghouse Digital Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product. Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90) days from the date of delivery to the end-user, whichever occurs last. OBTAINING WARRANTY SERVICE ­ To obtain warranty services, you must either personally deliver or ship the Product to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at (866) 287-5555 to obtain a Return Merchandise Authorization ("RMA") and for other instructions regarding return and replacement or repair of the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA. EXCLUSIONS TO WARRANTY ­ This warranty does not cover damage caused by (a) service or repairs by anyone other than personnel authorized by Westinghouse Digital Electronics, (b) the failure to utilize proper packing when returning the product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in transit or otherwise. PROOF OR ORIGINAL PURCHASE ­ A sales receipt, invoice, or other proof of purchase specifying the original date of purchase within the five (5) year warranty period must be presented to obtain warranty service. This warranty extends to the original purchaser and is not transferable. EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CLAIMED TO ARISE FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION AND SCOPE TO THE TERMS OF THIS WARRANTY. Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from State to State. Westinghouse Digital Electronics, LLC 16257 East Gale Ave. City of Industry, California 91745 Tel: (626) 333-9677. 8 of 8 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. and Westinghouse are trademarks of Westinghouse Electric Corporation and are used under license. Installing Adapter Brackets to the Flat Panel Screen Begin with product installation and assembly manual before reading this instruction manual. Model: MT80 THIN Parts List A C E F G H I K O S V Description Qty. Part # M4 x .7 x 12 mm phillips screw 6 504-9013 M4 x .7 x 25 mm phillips screw 6 504-1015 M5 x 40 mm pan head phillips scew 4 520-1199 M6 x 25 mm pan head phillips screw 4 520-1208 M6 x 1 x 20 mm pan head phillips screw 4 520-9402 M5 x .8 x 12 mm pan head phillps screw 4 520-1027 M6 x 1 x 12 mm pan head phillips screw 6 520-1128 M5 x 25 mm pan head phillips screw 6 520-9543 multi-washer 6 580-1036 .25" ID x .5" OD x .625" H nylon spacer 4 590-1106 .251" ID x .5" OD x 1.25" H aluminum spacer 4 580-1067 BB Note: This part is listed on the product installation and assembly manual. A C E F G H K I O S V 1 of 4 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 01-18-05 SHEET #: 201-9325-1 For customer service call 1-866-287-5555. To assemble the ada ...