User manual WESTINGHOUSE MT90 ARM29 - INSTALL GUIDE

Installation and Assembly - Adjustable Flat Panel Wall Arm IMPORTANT! Read entire instruction sheet before you start installation and assembly. Model: MT90 ARM29 MAX LOAD CAPACITY: 90 lb (40.9 kg) R This product is UL Listed. It must be installed by a qualified professional installer. WARNING · Installer must verify that the wall will safely support four times the combined weight of all attached equipment and hardware. WARNING · Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. Installations: To Wood Stud Walls .......................................................................................................... page 3 To Solid Concrete, Cinder Block, or Brick Walls ................................................................. page 4 1 of 9 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. Parts List PART # A 200-4413 B 200-4418 C 200-1052 D 200-4483 E 200-0441 F 200-0547 G 590-1089 H 5M9-025-X02 I J 560-9641 5S1-015-C04 QTY. 1 1 1 1 1 1 4 1 1 4 4 4 8 4 4 1 1 6 6 Before you start make sure all parts listed are included with your product. DESCRIPTION wall bracket swivel weldment wall support arm axle swivel bracket swing arm assembly roll pitch assembly cable clip holding pin snap ring #14 x 2.5" hex head phillips screw 3/8" screw head cover M8 x 16 mm phillips screw M6 x 10 mm phillips screw alligator anchor M10 x 1.5" x 15 mm phillips screw adapter bracket - top plate adapter bracket - bottom plate M4 x .7 x 16 mm phillips screw .5 OD x .44 ID x .19 bushing A B C D E F K 560-2029 L 520-2051 M 520-9524 N 590-0097 O 520-2202 P 200-4289 Q 200-4340 R 520-2088 S 590-1116 Some parts may appear slightly different than illustrated. K G H J N I L P M Q R O S 2 of 9 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. Installation To Wood Stud Walls Use wall bracket (A) as a template to mark and drill four 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Make sure wall bracket (A) is level and attach using #14 x 2 1/2" (6 mm x 38 mm) wood screws (J) and screw head covers (K). Tighten screws (J) with phillips screwdriver (not provided) and push screw head cover over wood screw heads (J). J K WARNING · Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. · Never tighten in excess of 80 in · lb (9 N.M.). · Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended. A 3 of 9 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. WARNING · When installing wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. · Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. · Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components. For Concrete Surfaces use wall bracket (A), making sure that it is level, as a template to mark holes. Drill 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Insert anchors (N) in holes flush with wall as shown (right). Place wall bracket (A) over anchors (N) and secure with #14 x 2.5" (6 mm x 65 mm) wood screws (J) and screw head covers (K). Tighten screws (J) with phillips screwdriver (not provided) and push screw head covers (K) over wood screw heads (J). 1 concrete surface N Drill holes and insert anchors (N) WARNING · Tighten concrete anchor bolts firmly, but do not overtighten. Overtightening can damage the bolts, greatly reducing their holding power. · Never tighten in excess of 80 in · lb (9 N.M.). 2 A J N Place plate over anchors (N) and secure with screws (J) WARNING · Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/ drywall (up to 5/8" thick) must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. 3 Tighten all fasteners (J) J INCORRECT CUTAWAY VIEW K CORRECT mounting plate concrete mounting plate concrete plaster/ dry wall plaster/ dry wall A 4 of 9 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. WARNING · Failure to correctly mount swing arm with plastic cap at top as shown in detail 3 will result in product failure. · Improperly installed snap rings will result in product failure. · If you are uncertain that product is properly installed, call customer service. Insert holding pin (H) into wall support arm axle (C). Insert axle (C) through wall bracket(A)and lower swing arm (E). Lock axle (C) in place with holding pin (H). IMPORTANT: Be sure swing arm (E) is in correct position shown below with plastic cap at top. Next thread snap ring (I) into groove at bottom of axle (C) protruding from wall bracket (A) as shown. SNAP RING INSTALLATION: Pull snap ring (I) apart. Wind it around the tube while feeding it into the groove. Finish by snapping the end of the snap ring into groove. NOTE: Fit of axle (C) into wall bracket (A) and lower swing arm (E) will be tight. Gently tap into place with a hammer if necessary. DETAIL 3 1 groove C H H C I E A E I pre-installed snap ring groove 2 3 I Insert swivel weldment (B) through swing arm (E). Align holes in swivel bracket (D) with holes in swivel weldment (B) and secure with four M6 x 10 mm phillips screws (M) as shown. B E M B D D 5 of 9 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. FOR VESA 100 MOUNTING PATTERN Use four M4 screws (R) and four bushings (S) to attach bottom plate (Q) to flat panel using phillips screwdriver (not provided). Use four center holes of bottom plate (Q) as shown below. FOR VESA 100 X 200 MOUNTING PATTERN Use six M4 screws (R) and six bushings (S) to attach bottom plate (Q) to flat panel using phillips screwdriver (not provided). Use six slots on bottom plate (Q) as shown below. Align upper end of slots with flat panel mounting holes. FLAT PANEL FLAT PANEL S R VESA 100 MOUNTING PATTERN S R Q 100 x 200 MOUNTING PATTERN Q Use four M6 screws (M) to attach top plate (P) to bottom plate (Q) using phillips screwdriver (not provided). NOTE: Top plate (P) will have one set of threaded holes on one side and a set of non-threaded holes on the other side. Bottom plate (Q) will also have one set of threaded holes on one side and a set of non-threaded holes on the other side. All four M6 screws (M) should pass through non-threaded holes first and into threaded holes. Q P Q M P 6 of 9 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. AT FL OF L CK ANE BA P Attach roll pitch assembly (F) to top plate (P) using four M10 x 15 mm phillips screws (O). P FLAT PANEL MAY APPEAR DIFFERENT THAN ILLUSTRATED F O WARNING · Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel. Insert two M8 screws (L) into roll pitch assembly (F). Leave approx. 1/4" of exposed thread as shown in detail. 1/4" L D L Hook roll pitch assembly (F)/flat panel onto swivel bracket (D). 7 of 9 Visit the Westinghouse Web Site at www.westinghousedigital.com Adjust tilt as needed and secure with two M8 x 16 mm screws (L). Use phillips screwdriver (not provided) to tighten screws (L). ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. Snap four cable clips (G) into swing arm assembly (E) as shown. G E 8 of 9 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. Limited Five-Year Warranty Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the "Product") that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5) years from the date of purchase by the original end-user, subject to the following terms and conditions: REPAIR OR REPLACEMENT ­ For a period of five (5) years from the original date of purchase, Westinghouse Digital Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product. Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90) days from the date of delivery to the end-user, whichever occurs last. OBTAINING WARRANTY SERVICE ­ To obtain warranty services, you must either personally deliver or ship the Product to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at (866) 287-5555 to obtain a Return Merchandise Authorization ("RMA") and for other instructions regarding return and replacement or repair of the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA. EXCLUSIONS TO WARRANTY ­ This warranty does not cover damage caused by (a) service or repairs by anyone other than personnel authorized by Westinghouse Digital Electronics, (b) the failure to utilize proper packing when returning the product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in transit or otherwise. PROOF OR ORIGINAL PURCHASE ­ A sales receipt, invoice, or other proof of purchase specifying the original date of purchase within the five (5) year warranty period must be presented to obtain warranty service. This warranty extends to the original purchaser and is not transferable. EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CLAIMED TO ARISE FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION AND SCOPE TO THE TERMS OF THIS WARRANTY. Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from State to State. Westinghouse Digital Electronics, LLC 16257 East Gale Ave. City of Industry, California 91745 Tel: (626) 333-9677. 9 of 9 Visit the Westinghouse Web Site at www.westinghousedigital.com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. and Westinghouse are trademarks of Westinghouse Electric Corporation and are used under license.