® Electric Washer/Dryer OVERALL DIMENSIONS PRODUCT MODEL NUMBER LTE6234D Electrical: A 3 or 4 wire, single phase, 120/240volt, 60-Hz., AC-only electrical supply (or 3 or 4 wire, 120/208-volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line must be provided. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit. Exhaust venting: Exhaust your dryer to the outside. Four-inch diameter vent is required. Rigid or flexible metal exhaust vent must be used. Do Not use plastic or metal foil vent. Exhaust outlet hood must be at least 12 inches from the ground or any object that may be in the path of the exhaust. The dryer can be converted to exhaust out right or left side. 71/" (181.9 cm) 23³/" (60.3 cm) 32¹/" (81.9 cm) * Most installations require a minimum 5¹/" (14 cm) clearance behind the dryer for the exhaust vent with elbow. *32" (81.3 cm) 27" (68.6 cm) RECESSED AREA AND CLOSET INSTALLATION Additional clearances might be required for wall, door and floor moldings. Rear clearance may be 0" (0 cm) when house exhaust system is lined up directly with dryer exhaust. A EXHAUST VENTING Select the route that will provide the straightest and most direct path outdoors. Plan the installation to use the fewest number of elbows and turns. Use the fewest 90° turns possible. Do not use vent runs longer than specified in vent length chart. Determine the number of elbows you will need. Recommended hood styles B B 6" (15.2 cm) 48 in.2 (310 cm2) C 3" (7.6 cm) 24 in.2 (155 cm2) 1" 32" 27" 0" 0" (0 cm) (68.6cm) (0 cm) (2.5 cm) (81.3 cm) 5¹/" (14 cm) 3" (7.6 cm) Angled hood style is acceptable. 4" (10.2 cm) A A. Recessed area B. Side view - closet or confined area C. Closet door with vents 2.5" (6.4 cm) 4" (10.2 cm) 4" (10.2 cm) DRAIN SYSTEM Standpipe drain system - wall or floor The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe adapter kit is available. The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (2.4 m) from the bottom of the washer. Laundry tub drain system The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 34" (86.4 cm) above the floor and no higher than 96" (2.4 m) from the bottom of the washer. Floor drain system The floor drain system requires a siphon break that may be purchased separately. The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses might be needed. A. Louvered hood style B. Box hood style Vent Length Chart No. of 90° turns or elbows 0 Type of Vent Box or Louvered hoods 37 ft (11.3 m) 25 ft (7.6 m) 32 ft (9.7 m) 21 ft (6.4 m) 24 ft (7.3 m) 15 ft (4.6 m) Angled hoods 35 ft (10.7 m) 20 ft (6.1 m) 27 ft (8.2 m) 16 ft (4.9 m) 19 ft (5.8 m) 10 ft (3.0 m) Rigid metal Flexible metal Rigid metal Flexible metal Rigid metal Flexible metal 1 2 NOTE: Side exhaust adds a 90° turn inside the washer/dryer. To determine maximum exhaust length, add one 90° turn to the chart. Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice. Ref. 8577199 08-24-05 ...