User manual XINDAK XA8800MNU

® INSTRUCTIONS XA8800MNu POWER AMPLIFIER XA8800MNu Chapter 1 Important Safety Instruction CAUTION ! Dangerous Voltage The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to presence of uninsulated "Dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. ! Important Instructions The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Marking by the "CE" symbol (shown left) indicates compliance of this device with the EMS (Electrornagnetic Compatibility) and LVD (low voltage directive) standards of the European Community. 1 XA8800MNu Chapter 1 Important Safety Instruction 1.1 Before Use Please read all instructions and precautions carefully and completely before operating your power amplifier. 1.Read these instructions. 2.Keep these instructions. 3.Heed all warnings. 4.Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Always keep this unit out of the reach of children. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus ( including produce heat. 9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Unplug this apparatus during lightning storms or when unused for a long time. 11. Always disconnect your entire system from the AC mains before connecting or disconnecting any cable, or when cleaning any component. 12. This product must be terminated with a three conductor AC mains power cord which includes an earth ground connection, to prevent shock hazard, all three connections must always be used. 13. AC extension cords are not recommended for use with this product. 14. Never use flammable or combustible chemicals for cleaning audio components. 15. Never operate this product with any cover removed. 16. Never pour or spill liquids directly onto this unit. 17. Never block air flow through ventilation slots or heat sinks. 18.Never by pass any fuse. 19. Never replace any fuse with a value or type other than those specified. 20. Never attempt to repair this product, if a problem occurs, contact your dealer. 21. Never expose this product to extremely high or low temperatures. 22. Never operate this product in an explosive atmosphere. amplifiers) that 1.2 Check Accessory Unpack your XA8800MNu power amplifier and keep all packing materials for future transport or service, locate and remove all accessory items from the accessory box within the controller shipping carton. Accessories Included: 1. AC power cord × 1 2. User manual (This manual) 2 XA8800MNu Chapter 2 Introduction 2.1 Product Features POWER POWER XA8800MNu is a mono power amplifier, with full symmetric current negative feedback structure. This model offers the user quality sound reproduction and elegant styling also features excellent look. The amplifying circuitry design follows the well appraised current negative feedback structure, featuring the full symmetric and full complementary circuit. The most outstanding advantages of this circuitry are powerful drive, low distortion, rich dynamics, excellent controlling ability, reliable work and good sound. The whole amplifying circuitry can be divided into three stages: the first stage adopts quality Motorola MJE350/MJE340 geminate transistors, the second stage adopts Toshiba 2SC517/2SA1930 geminate transistors and the output stage uses three pair of Sanken 2SC3264/2SA1295 high current geminate transistors. Therefore, this amplifier is ensured of power driving current. The materials are very select, especially some audio-use-only and world famous capacitances are choicely used in the audio loop. It uses imported relay to switch the coaxial channel and balanced channel. The whole power supply system is consisted of the 350W high quality annular transformer as the core, the 50A high speed bridge rectifier and 60,000 F Rubycon capacitance. The power supply for voltage amplifying is supplied by the filtered and rectified separate windings of the transformer, which have high speed, low noisy, low impedance and strong shielding ability. Besides, the separate design of the two windings can rapidly reduce the intermodulation disturbance and thus increase the purity of the sound. Additionally, this unit has perfect self-protection function. The core of the protect circuitry takes charge of the protect functions against output over current, over voltage and on/off surge with an indicator which will glitter in case of protect. IC was used as the controlling core, therefore, the general sensitivity and reliability is rapidly increased. Sound features: The excelsior circuitry and select materials endow this unit with mellow sound, excellent bounce in low and powerful drive. Besides, it is also dynamic, with extended soundstage. Sound of this unit is transparent, noble, elegant and vivid, especially full of rich changes. 3 XA8800MNu Chapter 2 2.2 Front Panel Introduction POWER uv u v The power supply on-off button Press this button, the current will be put through; press it again, the current will be cut off. Power Indicator After getting through, this indicator will wink for 8 seconds and then light. 2.3 Rear Panel NO.: u v wxy u v w The speaker binding post Connect it to the speaker by the speaker cable. x Signal Input Switch Switch between the coaxial and balance input channel Signal input jack Connect the input signal by signal cable. y Balance signal input jack Connect the input signal by the balanced signal cable. Power supply input jack and safety cutout jack Connect it to the power supply by attached power cord. 4 XA8800MNu Chapter 3 Operation Instruction 3.1 Connection Pre-Amplifier NO.: NO.: Right Channel XA8800MNu Power Amplifier Left Channel Connection to Power Supply 1.Before using this machine, you have to connect it to sound sources (such as CD player, DVD player, SACD player) by signal cable. Also you need to check if the signal connection of the left and right channel is correct and reliable. 2.Before connecting the machine to the right and left channel speaker by speaker cables, it's strongly suggested that you consult the dealer if your speaker cable is available for this machine and make sure of the right channel and polarity. 3.Please be very careful when connecting the power cable. Make sure the power supply has been cut off before connecting to the accessory power cable. If you do have to use other power cables, please check if the specifications are up to the requirements of this machine. We claim that we are not reliable for the damages caused by the use of other power cables. ! Please make sure all the power supplies have been cut off before connecting any cable to this machine. If you have no ability to install this machine, please ask those who are guided or are capable to accomplish the installation or connection. 5 XA8800MNu Chapter 3 3.2 General Problems and Trouble-shootings Operation Instruction Problem the machine is not electrified Possible cause Power connector not plug well Trouble-shootings Plug the power connector again. Change the fuse coincide with the prompt requirement. Turn on the sound source. Fuse has fused Sound source turned off Signal cable is broken Check and change signal cable. Speaker no sound Speaker cable is broken Check and change speaker cable. Tune input selection button according to sound source. Change a higher SNR sound. Signal selector switch wrong Root noise of sound source too big Noise too big Signal shielding effect badly Change eligible signal cable Left and right channel confused Signal source input phase opposed Speaker wire to channels has exchanged or positive negative reversed Connect according to the indication of left and right channel. Notice: if you have been confronted any problems when using this product or have any suggestion to tell us, please visit the wesite of xindak: http://www.xindak.com, you may access our instant technique support here. 6 XA8800MNu Chapter 4 4.1 Dimensions Unit: mm Specifications 240 POWER 7 XA8800MNu Chapter 4 4.2 Specifications Specifications < Power output 160W/ch (8ohm Load) < Rated power consumption < Frequency response < Signal-to-noise ratio < Distortion < Dimensions (W×D×H) < Input sensitivity < Net weight < Supply voltage 240W/ch 10Hz - 100KHz 100dB Typical(A Weight) <0.03% 240mm×148mm×430mm 1.7V 13Kg/ch Specified on rear panel decal * All specifications, dimensions and weights are subject to change without notice. 8 No.126, Section 2, East 1 Round Chengdu, Sichuan, China P.C. 610051 You can find your nearest authorized distributor and more product information on our website: www.xindak.com © 2006 XD3.834.065 SMS