Detailed instructions for use are in the User's Guide.
is a registered trademark of Chengdu Xindak Electronic Co.,LTD All rights reserved by Chengdu Xindak Electronic Co. LTD.
Chengdu Xindak Electronic Co. LTD.
No. 13, Zone A, Dongsheng Industry Park, Huaishudian Road, Chengdu, Sichuan, China.
INSTRUCTIONS XF-1000ES
AC LINE - Conditioner
Tel/Fax: 86 28 84711593 www.xindak.com
XD3.834.048 SMS
Printed in China
Chengdu Xindak Electronic Co. LTD.
PURPOSE AND CHARACTERS
Thank you for purchasing this AC LINE - Conditioner specially designed for Hi-Fi acoustics.It solved the problem of scattering sound and impure tones caused by the interface of miscellaneouswaves in the electrical network when playing.Meanwhile,it can be used for other electrical appliances in conformity with the conditions of this appliance,which filters the miscellaneous waves produced by appliance itself,but does not pollute the electrical network.To better use this appliance,please read the following content carefully.
INSTRUCTIONS XF-1000ES
The switch for the power supply control: Through this switch can turn on or turn off the power of Group 2 and Group 3 two output power socket groups. Output Group 1: Supply output current of 3A (Max.) to the electric equipment. This socket group CAN NOT be controlled by the power switch.On the power supply of the input socket is being putting through, this socket group will output the power. Output Group 2: Supply 5A(Max.) current to the electro-equipment. This socket group is controlled by the power switch. Output Group 3: Supply the output power of 5.5A (Max.) to the electric equipment. This socket group is controlled by the power switch.
AC POWER LINE RECEPTACLE/FILTER XF-1000ES
INDICATION
ON
3 Power Amplifier
1 2
DETECT
OFF
Subtotal 5.5A Max. (Switchable)
3 4
Subtotal 3A Max. (Unswitchable)
The grounded connection: This unit uses single-phase 3-lines input. When using the power supply with single-phase 2-lines input which is not grounded, must ground this connection.
5
The power input socket: The power input interface of this machine, with the fuse box.
1 Digital Accessories
7
USING STEP
Subtotal 5A Max. (Switchable)
2 Preamplifier/Accessories
6
This unit requires single-phase 3-lines input. When using single-phase 2-lines power input, DO connect the grounded biding post on back of the unit to the ground and make sure the phase of the input power is correct. Plug the attached 3-lines power cable into the power input socket on the rear panel, the power indicator will be light on. Touch the phase detect touching terminal to detect the phase of the power output socket. If the phase detect indicator is not light, the power output socket will be: A: Ground, B: Natural, C: Live. (See fig4) Otherwise, if the indicator is light it will be A: Ground, B: Live, C: Natural.
CHENGDU XINDAK ELECTRONIC CO., LTD
CAUTION
Always remove mains plug from wall socket before any service unless qualified to do so. This unit contains dangerous voltages
AC INPUT
220V/230V ±10%
50/60Hz FUSE F10A
RISK OF ELECTRIC SHOCK DO NOT OPEN
Polarity
AC POWER LINE RECEPTACLE/FILTER
XF-1000ES
9
Ground
1
SPECIFICATION
2
10
NO.:
Made in China
8
Rating .......................................................................... AC 250V 10A max. Max.Spike Volt ............................................................................. 3000V Max.Clamping Volt (8x20 SEC) ......................................................... 470V Max.Surge Current (8x20 SEC) ........................................................ 1000A Noise Filter ........................................................ -10dB55dB(2100MHz)
A
B
(Fig 4)
C
NOTICE NAME AND FUNCTION
1 Power Indication 4 Power Switch 7 Output Group 1
10
Because of the high voltage and heavy current inside, please not dismantle by yourself. If there is any fault, please cut off the power supply and send it to examine and repair. Please disconnect this unit with the power supply and the connected electric equipment, before changing the fuse.
2 Polarity Detect Button 5 Output Group 3 8 Power Input Socket 3 Voltage Meter 6 Output Group 2 9 Polarity Switch
PARAMETERS
Max Spike Volt.........................................................................3000V Max Clamping Volt (8X20s).......................................................470V Max Surge Current (8X20s).....................................................1000A Noise Filter..................................................-10dB~55dB(2-100MHz) Rating...................................................................AC250V 10A Max.
Grounded Connection
The phase detecting indicatorIndicate whether the phase of the power supply is corresponding. If the indicator is on when touch the DETECT button or the indicator has been on before touching it, it means the phase of the power supply is not corresponding, should change the phase switch to change its phase. The phase detectPut through the power. When the phase switch is in the position 1 ,touch the detect. If the indicator is on, it means the phase of the power supply input is not corresponding, should change the phase switch; if the indicator is off, it means the phase of the power supply input is corresponding. Voltage Meter: Indicate the voltage of the power supply. The value is only for reference.
...
