Handbuch Manual GB F D E Y akumo Recei ver XS DVBT Digi taler TV-Recei ver Safety Precautions WARNING: · TO REDUCE FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS YAKUMO RECEIVER XS DVB-T TO RAIN OR MOISTURE. · TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK PANEL. THERE ARE NO USERSERVICEABLE PARTS INSIDE. PLEASE REFER TO QUALIFIED SERVICE PERSONNEL. CAUTION:· Do not stack electronic components or other objects on top of the Yakumo Receiver XS DVB-T. The slots on top of the Yakumo Receiver XS DVB-T must be left uncovered to allow airflow to the unit. Blocking the air flow to the unit could impair performance or damage your Yakumo Receiver XS DVB-T and other components. · Do not stack the Yakumo Receiver XS DVB-T on top of a "hot component" such as an audio power amplifier. GB-1 Safety Precautions · Keep a clear space around the Yakumo Receiver XS DVB-T to allow for sufficient ventilation. · Use of cloth and mild solution of washingup liquid to clean the casing only when the yakumo receiver xs DVB-T is disconnected from the main power supply. · Do not connect / disconnect or modify cables when the Yakumo Receiver XS DVB-T is plugged in. · Do not cover the Yakumo Receiver XS DVB-T or place it on a unit that emits heat. · Avoid exposing the Yakumo Receiver XS DVB-T to direct sunlight. · Ensure that children do not poke objects into the ventilation slots. GB-2 Safety Information CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Please carefully study this manual and always keep it available. There are some installation and operation precautions which you should be aware of. 1.Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 2.Water and Moisture - Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. 3.A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 4.Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. GB-3 Safety Information c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. When the product exhibits a distinct change in performance - this indicates a need for service. 5. Do not connect or modify cables when the Yakumo Receiver XS DVB-T is plugged in. 6. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to per form saftey checks to determine that the product is in proper operating condition. GB-4 General Information Thank you for purchasing the Yakumo Receiver XS DVB-T. You have just purchased a fully DVB compliant digital terrestrial receiver. All functions can be carried out using the buttons on the remote control, and some of the functions can also be carried out using the buttons on the front panel. Please note that the actual controls and components, menu items, etc. of your Yakumo Receiver XS DVB-T may look somewhat different from those shown in theinstruction manual. Please be aware that new software may change the functionality of the Yakumo Receiver XS DVB-T. Should you experience any difficulties with the operation of your Yakumo Receiver XS DVB-T, please consult the relevant section of this manual or alternatively call your dealer or a customer service adviser. GB-5 Table of Contents Safety Precautions...........................................................1 Safety Information............................................................3 General Information.........................................................5 Table of Contents.............................................................6 Remote Control................................................................7 Panel Description...........................................................10 Systemic Connection.....................................................12 Basic Operation..............................................................13 Guide of Main Menu.......................................................14 Trouble Shooting............................................................30 Safety Warning...............................................................32 Service and Warranty.....................................................33 GB-6 Remote Control THE INSTRUCTIONS IN THIS MANUAL DESCRIBE THE FUNCTIONS ON THE REMOTE CONTROL. 1. POWER 2. NUMBERS 3. P/N 4. STB/VCR 5. INFO 6. CH+ 7. VOL8. CH9. GAME 10. EXIT 11. 16:9/4:3 12. P13. LANGUAGE 14. MUTE 15. R/L 16. TV/RADIO 17. VOL+ 18. OK 19. EPG 20. TELETEXT 21. MENU 22. P+ 1 14 5 3 15 2 4 6 7 21 11 12 22 16 19 17 10 18 20 8 9 13 GB-7 Remote Control 1. POWER: Switch between Operation and Standby modes. Press to change channel or enter your 2. NUMnumeric values on the menu. BERS: Select output mode for TV. 3. P/N: 4. STB/VCR: When VCR is playing, press to switch between VCR and STB; When VCR is closed, press to switch between CVBS and RGB. Display the information about the channel 5. INFO: and program. + Press to change channels or move up in 6. CH : the menus. Let up the volume. 7. VOL-: Press to change channels or move down 8. CH-: in the menus. Play the different game. 9. GAME: Exit the main menu or guide screen. 10. EXIT: 11. 16:9/4:3: Set video aspect ratio. Page down and let up the volume. 12. P-: Set the appropriate language 13. LANGUAGE: GB-8 Remote Control 14. MUTE: 15. R/L: 16. TV/RADIO: 17. VOL+: 18. OK: 19. EPG: 20. TELETXT: Press to mute/un-mute audio volume. Setup right or left channel. Press to switch between TV and RADIO. Advance the volume. Press to confirm choices. Display Electronic Program Guide menu. The servicer provided with text message transmitted to TV has Teletext decoder. The default setting is "OFF", press / and / button enter the Teletext or Teletext Subtitle. Display the main menu. Page up and advance the volume. 21. MENU: 22. P+: Note: Please take out of isolated plastic piece under battery, before you use the remove control for the first time. GB-9 Panel Description Front Panel 1 2 3 4 1. LED: Red light refers to the Yakumo Receiver XS DVB-T is in standby mode; Green light refers to the Yakumo Receiver XS DVB-T is on; Orange light refers to the VCR send the program to TV. 2. Channel up: Press to change channels or move up in the menus. 3. Channel down: Press to change channels or move down in the menus. 4. Standby button: Press to be (off) in standby mode. GB-10 Panel Description Rear Panel 8 1 2 3 4 5 6 7 1.RF IN: Aerial signals input. 2.RF LOOP THROUGH: Output signals to the next Yakumo Receiver XS DVB-T. 3.VCR: Connection to VCR. 4.TV: Connection to TV. 5. AUDIO: Audio signal to Hi-Fi system. 6. Coaxial: Connect the coaxial cable from the coaxial of the Yakumo Receiver XS DVB-T to the wired TV's jack. 7.RS232: Serial cable connector for downloading data, etc. 8. POWER CABLE: Connect to power source. GB-11 Systemic Connection The following figure is a simple guideline for installing the Yakumo Receiver XS DVB-T. If you have any problem about connection and need help, please contact your local dealer. · Install the antenna appropriately. Note: · To avoid damaging the Yakumo Receiver XS DVB-T, please make sure of antenna selecting "Off", if the sort of antenna is uncertain; then connect the antenna to the Yakumo Receiver XS DVB-T. GB-12 Basic Operation Switching Channel When the Yakumo Receiver XS DVB-T is turned on, the default setting is the TV program status. You can switch the current channel using one of the following methods. · Enter your desired channel numeric using the "NUMERICAL(0~9)" buttons to move the channel directly. · Press the "TV/RADIO" button to switch between TV channel and Radio channel. · Press the "OK" button to display Channel list, use the "CH+/CH-" and the "OK" button to select channel. Volume Control · Press the "V-/V+"or "P+/P-" button to adjust the audio volume. GB-13 Guide of Main Menu To display the Main Menu, press the "MENU" button. Program List TV Program List Music Program List Sort Automatic Search Manual Search Channel Lock Parental Setting Change PIN TV Standard Display Type Antenna Power Regional Setting Language Time Setting System Schedule Program Search Parental Control System Setting GB-14 Guide of Main Menu Game Mine Tetris GomoKu Calendar System Information Factory Default System Update Menu Color Transparency Level Border Pattern Entry Animation Accessory Personal Style Use the / button to move up or down from one item to another. The corresponding sub menu will be displayed on the TV screen as long as the "OK" button is pressed on the selected item.To escape the menu system at anytime, press "EXIT" or "MENU" button on the remote control. NOTE: If you use the Yakumo Receiver XS DVB-T for the first time, you will see the dialog on the TV screen as follows. GB-15 Guide of Main Menu First Time Installation First Time Installation Do you want to start first time Installation Wizard? YES NO The default setting is "YES", press either the "EXIT" or "MENU" button on the remote control to exit the dialog. When you press "OK" button on the remote control to select "YES", and then enter the "First Time Installation(1)" dialog. First Time Installation (1) Country Language Time Zone Antenna Power BACK Deutschland Deutsch GMT+00:00 OFF NEXT Press / button to select item desired. Select "NEXT" button to enter "First Time Installation (2)"dialog. GB-16 Guide of Main Menu First Time Installation (2) Do you want to start Auto search? Previous channel list will be replaced. BACK YES NO BACK: return to the upper menu. YES: start auto search. NO: cancel auto search, and enter the mail menu. Automatic Search Progress Channel No Frequency TV List: 000 50% 20 546MHz Music List 000 GB-17 Guide of Main Menu Program List TV Program List Under the main menu, moving / button of remote control to highlight the program list menu, then press the"OK" button to enter the TV Program List, and then will display the following list: No. Program edit table Program Name Favor Move Del The default highlight menu bar is the one on the first line or the one operated lastly. Moving / button of remote control to change the setting. GB-18 Guide of Main Menu Music Program List Under the main menu, moving / button of remote control to highlight the program list menu, then press the "OK" button to enter the Music Program List, and then will display the following list: No. Program edit table Program Name Favor Move Del The default highlight menu bar is the one on the first line or the one operated lastly. Moving / button of remote control to change the setting. GB-19 Guide of Main Menu Sort Under the main menu, moving / button of remote control to highlight the program list menu, then press the "OK" button to enter the Sort item, a sub-menu will appear on the TV screen. By Name By Service ID By Channel No. To select the desired in the program list, you should firstly display the Program list by directly pressing "OK" button on the remote control at the non-menu mode. When you use / button to switch from one channel to another, the video from the selected channel will be displayed on the screen. In order to make it convenient to find your required program in the list, press "OK" button on the remote control to sort all the programs in name, service ID, channel number. Switching between TV and radio programs is as easy as pressing "TV/RADIO" button on the remote control. The program list will disappear after pressing "EXIT" or "MENU" button. GB-20 Guide of Main Menu Program Search Under the main menu, moving / button of remote control to highlight the Program Search menu, then press the "OK" button to enter the sub-menu. For beginners, Auto Search is the best choice. First use / button to select Auto item in the program search menu and then press "OK" button to display Auto Search menu. Before here, you should select right country and default by using / button. If country is selected, the UHF band and VHF band used in your local will be scanned during searching. After finishing your settings, move cursor to the last item and press "OK" button to start the auto search. In this mode al ...