CRW2260t SERIES User Guide Guide de I'utilisateur Bedienungsanleitung COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: FAX: Type of Equipment: Model Name: Yamaha Systems Technology, Inc. 100 Century Center Court San Jose, California 95112 (408) 467-2330 (408) 437-8791 CD Recorder CRW2260t-B CRW2260t-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/ s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the product "OFF" and "ON", please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the leadin to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Systems Technology, Inc. 100 Century Center Court, San Jose, CA95112, U.S.A. · This manual applies to the CRW2260t-B and CRW2260t-NB. The CRW2260t-B front panel displays the YAMAHA brand name. The CRW2260t-NB front panel does not display a brand name. Laser Diode Properties Material : GaAlAs Wavelength : 782-789 nm Emission Duration : Continuous Laser Output Power : Less than 44.6 µW* * This output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT This compact disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label must be located on the exterior. VORSICHT : UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEOFFNET. NICHT DEM STRAHL AUSSETZEN. VARNING : OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN ÄR FARLIG. VARO! : AVATAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTINA NÄKYMÄTTÖMÄLLE LASERS TEILYLLE. ÄLÄ KATSO SÄTESSEN. ADVARSEL : USYNLIG LASERSTRALNING VED ÅBNING NÄR SIKKERHETSAFBYDERE ER UDE AF FUNKTION. UNDGÅ UDSETTELS FOR STRÅLING. Varningsanvisning för laserstrålning. WARNING f WARNING f · The temperature where CRW2260t is located should be between 5ºC and 40ºC (41ºF ­ 104ºF), when used in a fan-cooled system. · Do not disassemble the CRW2260t cover to reduce the risk of electric shock. · Always remove the disc before transporting CRW2260t. i Important Precautions Important Precautions Please read the following precautions before attempting to operate the CRW2260t. · Before recording a disc, be sure to clean the disc and tray using an air aerosol-type dust remover. A dust particle on the disc may cause recording to fail, producing an unusable disc. · Always record in a dust-free environment. If the disc must be removed from the CRW2260t before recording is finished, store the disc in a clean, dust-free environment. · The CRW2260t contains no user serviceable parts. Refer all servicing to qualified personnel. · If any of the following should occur, the CRW2260t should be serviced by qualified personnel: Metal objects or liquids get inside the CRW2260t. The CRW2260t does not operate normally or a marked change in performance is noticed. · Do not place heavy objects on the CD-RW discs. · Do not subject the CRW2260t and computer to impact or shock when in use, as this may impair recording or playback. · Yamaha is not responsible for any data or information losses resulting from the operation of the CRW2260t. ii Table of Contents Table of Contents Introduction ............................................................................. 1 CRW2260t Features ...................................................... 1 Orange Book Compatible Recording ............................ 2 Chapter 1 - System Configuration ..................................... 3 Computer ....................................................................... 3 Software......................................................................... 3 Tools .............................................................................. 4 Discs .............................................................................. 4 Chapter 2 - Installing the Yamaha CRW2260t Chapter 2 - Drive ..................................................................... 5 CRW2260t drive settings............................................... 5 Installing the CRW2260t drive...................................... 8 Chapter 3 - Operation .......................................................... 13 Front Panel................................................................... 13 Loading a Disc............................................................. 14 Ejecting the Disc.......................................................... 15 Manual Eject (emergency use) .................................... 16 Troubleshooting ................................................................... 17 Appendix................................................................................. 18 Specifications............................................................... 18 Front Panel Indicator Key............................................ 19 ©1997 Yamaha Corporation. All Rights Reserved. This document may not, in whole or in part, be copied, photocopied, reproduced, translated, transmitted or reduced to any electronic medium of machine readable form without prior consent in writing from Yamaha. MS-DOS and Windows are registered trademarks of Microsoft, Inc. Unix is a registered trademark of UNIX System Laboratories. All other trademarks are the property of their respective companies. iii Introduction Introduction Thank you for purchasing a Yamaha CRW2260t drive. Please read this manual before using the drive in order to make the best use of the superior CRW2260t functions. After reading, please retain this manual for future reference. CRW2260t Features s 2xS Recording (Rewritable) - 2xS Recording (Recordable) 6xS Reading The CRW2260t is able to write (overwrite) CD-RW discs at double speed, and is able to write CD-R discs double speed or normal speed. For both types of media, this drive is able to read at 6X speed, quad speed, double speed, or normal speed, and any of these modes can be selected as desired. s Compatible with Seven Different Formats The CRW2260t can both record and read seven different formats: CD-ROM, CD-ROM XA, CD-I, CD-DA, CD-Bridge (multisession), CDExtra, and Video CD. The CRW2260t is also equipped with an analog audio output terminal (headphones) for CD-DA. s SCSI 2 for High-Volume, High-Speed Data Transfer The CRW2260t features SCSI 2, the second generation SCSI interface for connecting computers and peripheral devices. s Compatible with Windows 95 Plug and Play SCSI IDs are set automatically by the SCAM protocol (level 1). s Orange Book Part 2, Part 3 Compatible 5-Mode Recording The CRW2260t conforms to the five recording modes outlined in the Orange Book Part 2 and Part 3: Track at Once, Multisession, Disc at Once, Session at Once, and Packet Writing. 1 Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD-ROM drives other than a CD-RW or CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Additional data can be written later. Disc at Once In this mode, data can be recorded to an entire disc in one pass. It is not possible to write additional data later. Session at Once In this mode, data can be recorded to disc one session at a time. To use this mode, your software must support Session at Once recording. New sessions can be written later. Packet Writing This is useful for data back-up. Smaller units of data can be added to tracks. To use this mode, your software must support Packet Writing. The CRW2260t supports both sequential and random packet writing. 2 Chapter 1 - System Configuration Chapter 1 - System Configuration Before using the CRW2260t, make sure that you have all of the items on the list of included items. In order to use the CRW2260t, you will require the following. Computer The following operating environment is required: · An IBM/AT compatible computer with a 100 MHz or faster Pentium CPU (in order to write at 4x speed), or a 100 MHz or faster 486 CPU (in order to write at 2x speed) A vacant slot in which to install a SCSI card or a pre-installed SCSI card A vacant half-height bay Windows 3.1, Windows 95, Windows NT4.0 or Higher Sufficient hard disk space · · · · Note: You will need about twice as much space on your hard disk as that required by the data you wish to write to CD-ROM. SCSI card This is required in order to connect a SCSI device (the Yamaha CRW2260t) to your computer. We recommend the following: Adaptec SCSI cards: AHA-2940 (PCI), AHA-284x (VL), AHA-2740 (EISA), AHA-154x (ISA), etc. Software Use writing software or packet writing software which supports the CRW2260t. 3 Chapter 1 - System Configuration Tools · Phillips screwdriver This is used to remove the cover of your computer, and to install the Yamaha CRW2260t drive. · Long nose pliers Phillips screwdriver These are used to insert or remove the jumper pin when setting the SCSI ID and parity settings etc.of the Yamaha CRW2260t drive. Long nose pliers Discs On the CRW2260t, you can use conventional CD-RW and CD-R discs that conform to the Recordable Compact Disc Systems Part 2 and Part 3 (Orange Book). Yamaha recommends the following Yamaha CD-RW and CD-R discs: CD-RW Discs > CRWM74R (120mm, 74 minutes) CD-R Discs > CDM12Y63 > CDM12Y74 > CDM12Y74M > CDM12Y74T (120mm, 63 minutes) (120mm, 74 minutes) (120mm, 74 minutes) (120mm, 74 minutes) Read-only Discs You can use discs with the logo which conform to the Compact Disc Read Only Memory standard (CD-ROM standard, Yellow Book). If you wish to use the audio functions, use discs with the logo, which conform to the Compact Disc Digital Audio standard (Red Book). 4 Chapter 2 - Installing the Yamaha CRW2260t Drive Chapter 2 - Installing the Yamaha CRW2260t Drive CRW2260t drive settings Before installing the CRW2260t in your computer, you will need to set the following jumpers. You set these jumpers by inserting jumper connectors into the jumper switch located on the rear panel of the CD-RW drive. o o o o SCSI ID settings Parity setting Terminator setting Block size setting Important: Use long-nose pliers to remove or insert jumper connectors. In the diagrams in this manual, solid black fill is used to indicate locations where a jumper is used to short between pins. Rear Panel VZ49880-0 VZ49890-0 AUDIO OUT RGL 124 ID SELECT PARITY TERMINATOR BLOCK SIZE SCSI INTERFACE CONNECTOR 1 DC INPUT G + 5V +12V Jumper Switch o SCSI ID settings The SCSI ID number is used so that the computer will recognize a connected SCSI device. You can assign 0 thro ...