User manual YAMAHA DVD-S663

G DVD PLAYER LECTEUR DVD DVD-S663 Important notes for users in the U.K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1 Remove fuse cover and fuse. 2 Fix new fuse which should be a BS1362 5 Amp, A.S.T. 3 Refit the fuse cover. If the fitted plug is not suitable for your jack outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. Note: The severed plug must be disposed to avoid a possible shock hazard should it be inserted into a 13 Amp jack elsewhere. How to connect a plug The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L). · As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows: ­ Connect the blue wire to the terminal marked N or coloured black. ­ Connect the brown wire to the terminal marked L or coloured red. ­ Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green (or green and yellow). Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires. Copyright in the U.K. Recording and playback of material may require consent. See Copyright Act 1956 and The Performer's Protection Acts 1958 to 1972. VAROITUS Muiden kuin tässä esitettyjen toimintojen säädön tai asetusten muutto saattaa altistaa vaaralliselle säteilylle tai muille vaarallisille toiminnoille. DK Advarsel: Usynlig laserstråling ved åbning når sikkerhedsafbrydere er ude af funktion. Undgå utsættelse for stråling. Bemærk: Netafbryderen STANDBY/ON er sekundært indkoblet og ofbryder ikke strømmen fra nettet. Den indbyggede netdel er derfor tilsluttet til lysnettet så længe netstikket sidder i stikkontakten. N Observer: Nettbryteren STANDBY/ON er sekundert innkoplet. Den innebygdenetdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet nettkontakten. S Klass 1 laseraparat Varning! Om apparaten används på annat sättþän i denna bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1. Observera! Strömbrytaren STANDBY/ON är sekundärt kopplad och inte bryter inte strömmen från nätet. Den inbyggda nätdelen är därför ansluten till elnätet så länge stickproppen sitter i vägguttaget. SF Luokan 1 laserlaite Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. Oikeus muutoksiin varataan. Laite ei saa olla alttiina tippu-ja roiskevedelle. Toiminnanvalitsin STANDBY/ON on kytketty toisiopuolelle, eikä se kytke laitetta irti sähköverkosta. Sisäänrakennettu verkko-osa on kytkettynä sähköverkkoon aina silloin, kun pistoke on pistorasiassa. VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄ TEESEEN. VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN. i En CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. AVERTISSEMENT L'utilisation de commandes et l'emploi de réglages ou de méthodes autres que ceux décrits dans le présent document, peuvent entraîner une exposition à un rayonnement dangereux. VORSICHT Die Verwendung von Bedienelementen oder die Einstellung bzw. die Ausführung von anderen als in dieser Anleitung beschriebenen Vorgängen kann zu Gefährdung durch gefährliche Strahlung führen. OBSERVERA Användning av reglage eller justeringar eller utförande av åtgärder på annat sätt än så som beskrivs häri kan resultera i farlig strålning. ATTENZIONE L'uso di controlli, regolazioni, operazioni o procedure non specificati in questo manuale possono risultare in esposizione a radiazioni pericolose. PRECAUCIÓN El uso de los controles, los ajustes o los procedimientos que no se especifican enste manual pueden causar una exposición peligrosa a la radiación. LET OP Gebruik van bedieningsorganen, instellingen of procedures anders dan beschreven in dit document kan leiden tot blootstelling aan gevaarlijke stralen. OSTRZEENIE Uywanie regulatorów i nastawie w inny spos ób lub wykonywanie procedur innych ni tutaj podane moe by przyczyn niebezpiecznego promieniowania. CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING. UNDGÅ UDSÆTTELSE FOR STRÅLING. ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES. UNNGÅ EKSPONERING FOR STRÅLEN. VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN. VARO! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄ TEILYLLE. ÄLÄ KATSO SÄTEESEEN. VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETSEN. DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE. EXPOSITION DANGEREUSE AU FAISCEAU. OSTRZEENIE WIDZIALNE I NIEWIDZIALNE PROMIENIOWANIE LASEROWE PO OTWARCIU. UNIKA NARAENIA NA WIZK LASEROW. DANGER: INVISIBLE LASER RADIATION WHEN OPEN CAUTION:INVISIBLE LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM AVOID DIRECT EXPOSURE TO THE BEAM ii En CAUTION: READ THIS BEFORE OPERATING THIS UNIT. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this unit in a well ventilated, cool, dry, clean place -- away from direct sunlight, heat sources, vibration, dust, moisture, or cold. In a cabinet, allow about 2.5 cm (1 inch) of free space all around this unit for adequate ventilation. 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. 4 Do not expose this unit to sudden temperature changes from cold to hot, nor locate this unit in an environment with high humidity (i.e., a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. 5 Avoid installing this unit in a location where foreign objects may fall onto this unit or where this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: ­ Other components, as they may cause damage and/or discoloration on the surface of this unit. ­ Burning objects (i.e., candles), as they may cause fire, damage to this unit, and/or personal injury. ­ Containers with liquid in them, as they may fall, spilling the liquid and causing an electrical shock to the user and/or damage to this unit. 6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. 7 Do not plug in this unit to a wall outlet until all connections are complete. 8 Do not operate this unit upside-down. It may overheat, possibly causing damage. 9 Do not use excessive force on switches, knobs and/ or cords. 10 When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord. 11 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. 12 Use only the voltage specified on this unit. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than as specified. 13 Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reason. 14 When not planning to use this unit for long periods of time (i.e., vacation), disconnect the AC power plug from the wall outlet. 15 Be sure to read the "Troubleshooting" section on common operating errors before concluding that this unit is faulty. 16 Before moving this unit, press STANDBY/ON to set the unit in standby mode, then disconnect the AC power plug from the wall outlet. 17 Install this unit near the AC outlet and where the AC power plug can be reached easily. 18 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. The unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. LASER SAFETY This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device. DANGER This unit emits visible laser radiation when open. Avoid direct eye exposure to beam. When this unit is plugged into a wall outlet, do not place your eyes close to the opening of the disc tray and other openings or look inside. iii En Contents English Introduction ................................... 3 About this manual........................................ 3 Supplied accessories .................................. 3 Region codes ............................................... 3 Playable disc formats .................................. 4 Cleaning discs.............................................. 4 Patent information ....................................... 5 Playback Operation .................... 17 Basic operation.......................................... 17 Selecting a track/chapter ...................................17 Searching backward/forward ............................17 Repeat/Shuffle functions .......................... 17 Repeat/Shuffle playback ...................................17 Repeating a section within a chapter/track .......18 Operations for video playback (DVD/VCD/SVCD)..................................... 18 Using the disc menu..........................................18 Playback in slow motion ...................................18 Zooming pictures in/out....................................18 Resuming playback from the last stopped point ...........................................................................18 Using the on-screen display (OSD) ..................19 Special DVD features ................................ 20 Playing by title ..................................................20 Selecting an audio language/format and subtitle language ............................................................20 Special VCD/SVCD features...................... 20 Using the playback control (PBC) menu ..........20 Playing data discs (MP3/WMA/WMV/JPEG/DivX®)............... 21 Selecting a folder and track/file ........................21 Special picture disc features .................... 21 Using the preview function ...............................21 Zooming pictures in/out....................................22 Playback with multi-angles...............................22 Playing MP3 music and JPEG pictures simultaneously ..................................................22 Special DivX® features .............................. 22 Using the interactive menu ...............................22 Selecting an audio/subtitle language.................22 Using a USB device ................................... 23 Supported USB devices ....................................23 Playing data files...............................................23 Functional Overview ..................... 6 Front panel ................................................... 6 Rear panel..................................................... 7 Remote control............................................. 8 Connections................................... 9 General notes on connections ................... 9 Audio connections....................................... 9 Digital connection ...............................................9 Analog connection...............................................9 Video connections ..................................... 10 Component video jacks .............................10 S-video jack ...............................................10 Composite video jack ................................10 SCART terminal (Europe and Russia models only)......................10 HDMI connection........................................ 11 HDMI jack.........................................................11 Other connections ..................................... 12 USB port............................................................12 Remote control jacks .........................................12 Getting Started ............................ 13 Step 1: Inserting batteries into the remote control ...................................................... 13 Using the remote control ...................................13 Step 2: Turning on the power ................... 13 Step 3: Setting a TV type/display and language................................................... 14 Setting a color system for your TV ...................14 Setting an aspect ratio for your TV ...................15 Setting the OSD Language................................15 Setting the audio, subtitle, and disc menu languages (DVD-Video only) ...........................16 Continued 1 En Contents Setup Menu .................................. 25 Menu overview ........................................... 25 Setup menu operation ............................... 27 General setup menu .................................. 28 Locking/Unlocking the disc for viewing...........28 Recording CD tracks onto your USB device ....28 Programming disc tracks (except MP3/WMA/WMV/JPEG/DivX®)........30 Dimming the front panel display.......................30 OSD language ...................................................30 Setting the screen saver .....................................31 Setting the sleep timer .......................................31 Displaying the DivX® VOD registration code ...........................................................................31 Audio setup menu...................................... 31 Setting the analog output...................................31 Setting the digital output ...................................32 Turning the HDMI audio on/off........................32 Turning the night mode on/off ..........................33 Video setup menu ...................................... 33 TV type..............................................................33 Setting the TV display.......................................33 Turning the progressive scan function on/off ...34 Adjusting picture settings..................................34 Turning the black level on/off ...........................35 Turning the closed caption on/off .....................35 Switching YUV/RGB (Europe and Russia models only)......................36 Setting the HDMI video ....................................36 Preference setup menu ............................. 37 Audio, subtitle and disc menu ...........................37 Restricting playback with parental control........37 Selecting playback of VR format ......................38 Selecting the data disc menu .............................38 Selecting DivX® external subtitle group (except Korea model) ........................................38 Selecting the PBC (playback control) function ...........................................................................39 Setting the auto standby function ......................39 Changing the password .....................................40 Resetting the system..........................................40 Language Codes ......................... 41 Troubleshooting.......................... 42 Glossary....................................... 46 Specifications.............................. 48 Europe model Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/ 96/EC and 2006/66/EC. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [Information on Disposal in other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. 2 En Introduction Introduction English About this manual Thank you for purchasing this unit. This owner's manual explains the basic operation of this unit. · Illustrations in this manual are based on the Europe model unless otherwise specified. · Notes contain important information about safety and operating instructions. · y indicates a tip for your operation. · This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priority. Region codes This unit is designed to support the region management system. Check the regional code number on the DVD disc package. If the number does not match the region code of this unit (see the table below or the back of this unit), this unit may be unable to play the disc. Region code of this unit Playable discs Destination U.S.A., Canada 1 2 1 2 3 4 5 ALL Europe Supplied accessories For Europe and Russia models ALL · Remote control · Two batteries (AAA, R03, UM-4) for the remote control · RCA stereo cable · Composite video cable For U.S.A., Canada, Central and South America, Australia, Asia, and Korea models Asia, Korea 3 4 5 ALL Australia, Central and South America Russia ALL ALL · Remote control · Two batteries (AAA, R03, UM-4) for the remote control · Audio/video cable 3 En Introduction Playable disc formats This unit is designed for use with discs having the logos shown below. Do not attempt to load any other type of disc into this unit. Notes · CD-R/RW, DVD-R/RW/R DL, and DVD+R/RW/ R DL cannot be played unless finalized. · Progressive JPEG, copyright-protected WMA and WMV files cannot be played with this unit. · This unit is not compatible with WMV Advanced profile. · Only the first session of DVD-R/RW/R DL and DVD+R/R DL can be played. · Discs without logos shown left are not guaranteed to function. · Some discs cannot be played depending on disc characteristics or recording conditions even if they have the logos shown left. · Do not use any non-standard shaped discs (heart-shaped, etc.). · Do not use discs with tape, seals, paste or many scratches on their surface. This unit can play: · DVD-R/RW/R DL and DVD+R/RW/R DL discs recorded in DVD-Video compatible format · DVD-R/RW discs recorded in VR format (compatible with CPRM) · MP3, WMA, WMV, and JPEG files recorded on CD-R/RW, DVD-R/RW, DVD+R/RW, and USB device · KODAK picture CDs, FUJICOLOR CDs · ISO 9660 Level1/Level2 for CD-R/RW · Up to 298 folders per disc/USB device and up to 648 files per folder with up to 8 hierarchies · DivX® files recorded on CD-R/RW, DVD-R/RW, DVD+R/RW, and USB device ­ Official DivX® Ultra Certified product ­ Plays all versions of DivX® video (including DivX® 6) with enhanced playback of DivX® media files and the DivX Media Format y For details about playable formats, see "Specifications" on page 48. Cleaning discs · When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out. Do not wipe in a circular motion. · Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analog records. 4 En Introduction English Patent information Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license under U.S. Patent No's : 5,451,942 and other U.S. and worldwide patents issued and pending. DTS and DTS Digital Out are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. Copyright 1996-2007 DTS, Inc. All Rights Reserved. DivX, DivX Ultra Certified, and associated logos are trademarks of DivX, Inc. and are used under license. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. 5 En Functional Overview Functional Overview Front panel 1 1 STANDBY/ON 2 3 45 6 7890 q 6 Front panel display Shows the current status of this unit. Turns on this unit or sets it to the standby mode (see page 13). In the standby mode, this unit consumes a small amount of power in order to receive infrared signals from the remote control. 7 Remote control sensor Receives infrared signals from the remote control (see page 13). 2 Disc tray Loads a disc in the disc tray (see page 17). 8 PLAY ( p ) Starts playback. 3 OPEN/CLOSE ( 4 HDMI indicator ) Opens or closes the disc tray (see page 17). Lights up when an HDMI component is connected and signals output via the HDMI jack of this unit. 9 PAUSE ( ) Pauses playback. Frame-by-frame playback (see page 17). 0 STOP ( s ) Stops playback. 5 PROGRESSIVE indicator Lights up when this unit is in the progressive mode (see page 34). q USB port Connect the USB connector of your USB device (see page 12). 6 En Functional Overview English Rear panel PR / CR COMPONENT Y VIDEO MAINS REMOTE CONTROL OUT IN HDMI AUDIO OUT COAXIAL DIGITAL OUT PB / CB S VIDEO VIDEO OUT AV 1 1 AC power cable 2 3 4 5 678 9 (Europe model) 5 DIGITAL OUT - COAXIAL jack Connect to the coaxial input jack of your AV receiver (see page 9). Plug the power cable into the AC wall outlet. 2 REMOTE CONTROL (IN, OUT) jacks Connect the REMOTE CONTROL (IN) jack of this unit to the remote control output jack of your Yamaha AV receiver (see page 12). Connect the REMOTE CONTROL (OUT) jack of this unit to the remote control input jack of your Yamaha component. 6 VIDEO OUT - COMPONENT (Y, PB/CB, PR/ CR) jacks Connect to the component input jacks of your AV receiver (see page 10). 7 VIDEO OUT - S VIDEO jack Connect to the S-video input jack of your AV receiver (see page 10). 3 HDMI jack Connect to the HDMI input jack of your HDMI component (see page 11). 8 VIDEO OUT - VIDEO jack Connect to the composite video input jack of your AV receiver (see page 10). 4 AUDIO OUT (L, R) jacks Connect to the audio input jacks of your AV receiver or stereo system (see page 9). 9 AV terminal (Europe and Russia models only) Connect to the SCART input terminal of your TV (see page 10). Caution: Do not touch the inner pins of the jacks on the rear panel of this unit. Electrostatic discharge may cause permanent damage to this unit. 7 En Functional Overview Remote control 67 Stops playback (see page 17). Opens the disc tray.* 1 2 3 4 5 6 7 8 9 7 Numeric buttons (0-9) 0 Selects numbered items in the currently displayed menu. 8 SUBTITLE Selects the subtitle language (see pages 20 and 22). q w e r 9 ZOOM Enlarges or shrinks the video image (see pages 18 and 22). 0 ON SCREEN Accesses or exits from the on-screen display (OSD) menu of this unit (see page 19). t y u q SET UP Accesses or exits from the setup menu of this unit (see pages 14 and 27). w 33l Moves to the next chapter or track (see page 17). Searches forward (see page 17).* 1 Turns on this unit or sets it to the standby mode (see page 13). In the standby mode, this unit consumes a small amount of power in order to receive infrared signals from the remote control. e 3/ 8 Starts or pauses playback (see page 17). r USB Accesses the contents of the connected USB device or exits from the USB mode (see page 23). 2 TOP MENU/RETURN Displays the top-level disc menu (DVD). Moves back to the previous menu (DVD*/VCD) (see page 20). t AUDIO Selects the audio language or format (see pages 20 and 22). 3 2 / 3/5/a Selects an item in the currently displayed menu. Search or slow playback (see page 27). ENTER Confirms the menu selection (see page 27). y REPEAT Accesses or exits from the repeat/shuffle mode (see page 17). u REPEAT A-B Repeats a specified segment (see page 18). * Press and hold the button for about two seconds. 4 MENU Displays the menu of a disc (DVD/JPEG) (see pages 18, 20, 21 and 22). Switches PBC on or off (VCD) (see page 20). 5 l22 Moves to the previous chapter or track (see page 17). Searches backward (see page 17).* 8 En Connections Connections English Notes · You need to set [DIGITAL OUTPUT] to [ALL] (see "DIGITAL OUTPUT" on page 32). · If the audio format of the digital output does not match the capabilities of your receiver, the receiver produces a distorted sound or no sound at all. Make sure to select the appropriate audio format from the menu screen on the disc. Pressing AUDIO on the remote control once or more may change not only the audio languages but also the audio format. The selected format appears on the TV screen for several seconds. · If you want to enjoy Dolby Digital and DTS formats, you must connect this unit to an AV receiver that supports these formats. General notes on connections Be sure to turn off this unit and unplug the power cable before you make or change connections. · Depending on the component you want to connect, there are various ways to make connections. Possible connections are described below. · Refer to the manuals supplied with your other components as necessary to make the best connections. · Do not connect this unit via your VCR. The video quality could be distorted by the copy protection system. · Do not connect the audio out jack of this unit to the phono in jack of your audio system. Analog connection This unit has 2-ch analog output jacks. Connect the AUDIO OUT (L, R) jacks of this unit to the corresponding input jacks of your audio component (such as a stereo amplifier) using the supplied RCA stereo cable (Europe and Russia models) or audio/video cable (other models). This unit (Europe model) PR / CR COMPONENT Y VIDEO Audio connections Digital connection This unit has a digital coaxial output jack. Connect the DIGITAL OUT - COAXIAL jack of this unit to your AV receiver equipped with a Dolby Digital or DTS decoder using a commercially available coaxial digital audio cable. This unit (Europe model) PR / CR COMPONENT Y VIDEO AUDIO OUT COAXIAL DIGITAL OUT PB / CB S VIDEO VIDEO OUT AV L R RCA stereo cable (Europe and Russia models) or audio/video cable (other models) (supplied) L AUDIO OUT COAXIAL DIGITAL OUT PB / CB S VIDEO VIDEO OUT AV R Stereo amplifier C Coaxial digital audio cable C L R AV receiver Speakers Speakers 9 En Connections Video connections Make video connections to your receiver and TV so that you can use one TV for several different video sources (LD, VCR, etc.) by simply switching the input source selector of your receiver. This unit has several types of video output jacks. Use the one that corresponds to the input jacks of the component to be connected. This unit (Europe model) PR / CR COMPONENT Y VIDEO commercially available component video cable. Observe the color of each jack when you make connections. If your receiver does not have component output jacks, you can achieve a better video image by connecting the component output jacks of this unit directly to the component input jacks of your TV. S-video jack S-video connections achieve a clearer picture than composite video connections by transmitting video signals on separate wires for luminance (Y) and chrominance (C). Connect the VIDEO OUT - S VIDEO jack of this unit to an S-video input jack of your AV receiver and then to that of your TV using a commercially available S-video cable. AUDIO OUT COAXIAL DIGITAL OUT PB / CB S VIDEO VIDEO OUT AV PR PB Y S V Component video cable S-video cable Composite video cable (Europe and Russia models) or audio/video cable (other models) (supplied) Composite video jack Connect the VIDEO OUT - VIDEO jack of this unit to a video input jack of your AV receiver and then to that of your TV using the supplied composite video cable (Europe and Russia models) or audio/video cable (other models). PR PB Y V S PR/CR PB/CB Y COMPONENT VIDEO IN S VIDEO INPUT VIDEO INPUT AV receiver COMPONENT VIDEO OUT COMPONENT VIDEO IN S VIDEO OUT S VIDEO IN VIDEO OUT VIDEO IN SCART cable SCART terminal (Europe and Russia models only) You may connect the TV directly to this unit. Connect the AV terminal of this unit to the SCART input terminal of your TV using a commercially available SCART cable. The AV terminal outputs composite and RGB video signals together with 2-ch audio signal. Set the output of the video signal in "Switching YUV/RGB (Europe and Russia models only)" on page 36. TV Component video jacks Component video connections achieve higher fidelity color reproduction than S-video connections by transmitting video signals on separate wires for luminance (Y: green) and chrominance (PB: blue, PR: red). Connect the VIDEO OUT - COMPONENT (Y, PB/CB, PR/CR) jacks of this unit to component input jacks of your AV receiver and then to those of your TV using a 10 En Connections English HDMI connection HDMI jack HDMI (High-Definition Multimedia Interface) provides high quality digital audio and video on a single connection. Connect the HDMI jack of this unit to an HDMI input jack of your AV receiver, and then to that of your TV using a commercially available HDMI cable. If your receiver does not have an HDMI input jack, you can achieve a better video image by connecting the HDMI jack of this unit directly to the HDMI input jack of your TV. This unit can display High-Definition JPEG images (720p, 1080i, or 1080p) when you connect this unit to an HDTV via the HDMI jack. For details, see "HD JPEG" on page 37. This unit (Europe model) PR / CR COMPONENT Y VIDEO Notes · You need to set [HDMI AUDIO] (see page 32) and [HDMI VIDEO] (see page 36) properly. · You need to make appropriate audio connections if the connected component does not output audio signals (see "Audio connections" on page 9). · This unit is not compatible with HDCPincompatible HDMI or DVI components. · You need a commercially available HDMI/DVI conversion cable when you connect this unit to other DVI components. In this case, the HDMI jack of this unit does not output any audio signals. · Depending on the connected DVI component, black and white in the image may not be distinct. In that case, adjust the picture setting of the connected DVI component. · Do not disconnect or turn off the power of the HDMI/DVI component connected to the HDMI jack of this unit during playback. Doing so may disrupt playback or cause noise. y When connecting an HDMI component, refer to the manual supplied with your component. HDMI AUDIO OUT COAXIAL DIGITAL OUT PB / CB S VIDEO VIDEO OUT HDMI cable HDMI IN AV receiver HDMI OUT HDMI IN TV 11 En Connections Other connections USB port This unit has a USB port and can access MP3, WMA, WMV, JPEG, and DivX® files saved on your USB device. Connect a USB connector of your USB device to the USB port on the front panel of this unit. When your USB device is connected to the USB port of this unit, you can record tracks on a CD onto your USB device in MP3 format. For details, see "Recording CD tracks onto your USB device" on page 28. To disconnect the USB device, press 7 to stop playback, press USB to return to the disc mode, and then disconnect the device from this unit. This unit Monaural 3.5 mm mini plug cable Remote control jacks This unit has remote control input/output jacks. If your AV receiver is a Yamaha product and has the capability to transmit SCENE control signals, you can use the SCENE function. Connect the REMOTE CONTROL (IN) jack of this unit to a remote control output jack of your receiver using a commercially available monaural 3.5 mm mini plug cable so that this unit starts playback automatically by simply pressing a SCENE button of your receiver. This unit MAINS REMOTE CONTROL OUT IN HDMI REMOTE OUT AV receiver USB device y · For details about the SCENE function, refer to the owner's manual supplied with your Yamaha AV receiver. · You can connect a Yamaha component (such as DVD player and CD player) corresponds with the SCENE function to the REMOTE CONTROL (OUT) jack of this unit. Note This unit may not recognize some USB devices. y For details about the USB features, see "Using a USB device" on page 23. 12 En Getting Started Getting Started English Step 1: Inserting batteries into the remote control 3 1 2 Using the remote control Use the remote control within 6 m (approximately 20 ft) of this unit and point it toward the remote control sensor. Within 6 m (approximately 20 ft) 1 Open the battery compartment. 2 Insert the two supplied batteries (AAA, R03, UM-4) following the indications (+/­) inside the compartment. Notes · Do not spill water or other liquids on the remote control. · Do not drop the remote control. · Do not leave or store the remote control in the following types of conditions: ­ places of high humidity, such as near a bath ­ places of high temperature, such as near a heater or stove ­ places of extremely low temperature ­ dusty places · When the remote control works unstably, point it at an angle upward to the sensor. 3 Close the cover. Notes · Insert batteries correctly according to the polarity markings (+/­). Batteries inserted in the opposite orientation may leak. · Replace the exhausted batteries immediately with new ones to prevent leakage. · Remove the batteries from the compartment if the remote control is not used for more than a month. · If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. · Do not use old batteries together with new ones. · Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. · Dispose of the batteries correctly in accordance with your local regulations. Step 2: Turning on the power 1 Plug the power cable into the AC outlet. 2 Turn on your TV and AV receiver. 3 Select the appropriate input source of the AV receiver (refer to the manual supplied with your AV receiver). 4 Press STANDBY/ON on the front panel or on the remote control to turn on this unit. The front panel display lights up. 5 Set the TV to the correct video input (refer to the manual supplied with your TV). The default screen appears on the TV. 13 En Getting Started Step 3: Setting a TV type/display and language You can customize this unit using the setup menu displayed on the TV screen. Note Unless stated otherwise, all operations described here are carried out using the supplied remote control. PAL Select this if the connected TV is a PAL system TV. It will change the video signals of NTSC discs and output them in PAL format. NTSC Select this if the connected TV is an NTSC system TV. It will change the video signals of PAL discs and output them in NTSC format. MULTI y · To return to the previous menu, press 2. · If the setting you have selected are not appropriate, you can reset all settings to the initial factory settings (see "Resetting the system" on page 40). Select this if the connected TV is compatible with both NTSC and PAL formats (such as a multi-system TV). The output format will be in accordance with the video signals of the disc. 5 Select an item, and then press ENTER. 6 Press SET UP to exit from the menu. Notes · Before changing the current TV standard setting, ensure that your TV supports the selected TV type. · When making HDMI connections, you cannot change or select [TV TYPE]. Setting a color system for your TV This unit is compatible with both NTSC and PAL video formats. Select the color system that matches your TV. VIDEO SETUP PAGE TV TYPE TV DISPLAY PROGRESSIVE PICTURE SETTING BLACK LEVEL CLOSED CAPTION ....... COMPONENT HDMI SETUP PAL NTSC MULTI y If the picture is not displayed properly on your TV, wait for 15 seconds for this unit to activate automatic recovery. * *: [COMPONENT] is only for Europe and Russia models. 1 Press SET UP. 2 Press 3 repeatedly to select "VIDEO SETUP PAGE". 3 Press 5/a to highlight [TV TYPE], and then press 3. 4 Press 5/a to highlight one of the following options. 14 En Getting Started English Setting an aspect ratio for your TV You can set the aspect ratio of this unit to match your TV. If the aspect ratio of your TV is 16:9, you do not need to change this setting. For details, see "Setting the TV display" on page 33. Setting the OSD Language You can select your own preferred language for the setup menu. This setting remains once selected. GENERAL SETUP PAGE DISC LOCK MP3 RECORD PROGRAM DISPLAY DIM OSD LANGUAGE SCREEN SAVER SLEEP DIVX(R) VOD CODE ENGLISH DANSK DEUTSCH ESPAÑOL FRANÇAIS ITALIANO NEDERLANDS NORSK VIDEO SETUP PAGE TV TYPE TV DISPLAY PROGRESSIVE PICTURE SETTING BLACK LEVEL CLOSED CAPTION ....... COMPONENT HDMI SETUP 4:3 PAN SCAN 4:3 LETTER BOX 16:9 * * menu items *: Themodels. may change depending on the *: [COMPONENT] is only for Europe and Russia models. 1 Press SET UP. 2 Press 3 repeatedly to select "VIDEO SETUP PAGE". 1 Press SET UP. 2 Press 2 / 3 to select "GENERAL SETUP PAGE". 3 Press 5/a to highlight [OSD LANGUAGE], and then press 3. 3 Press 5/a to highlight [TV DISPLAY], and then press 3. 4 Press 5/a to select a language, and then press ENTER. 4 Press 5/a to highlight the desired setting, and then press ENTER. 5 Press SET UP to exit from the menu. 5 Press SET UP to exit from the menu. 15 En Getting Started Setting the audio, subtitle, and disc menu languages (DVD-Video only) You can select your own preferred language for the audio, subtitle, and disc menu. This unit automatically switches to the selected language whenever you load a disc. If the selected language is not available on the disc, the default language of the disc will be used instead. To select a language not in the list 1 Select [OTHERS] in [AUDIO], [SUBTITLE], or [DISC MENU], and then press ENTER. 2 Use the numeric buttons (0-9) to enter the 4-digit language code (see "Language Codes" on page 41), and then press ENTER. 3 Press SET UP to exit from the menu. PREFERENCE PAGE AUDIO SUBTITLE DISC MENU PARENTAL VR LIST DATA DISC NAV DIVX SUBTITLE PBC ENGLISH CHINESE (SIMP) FRENCH SPANISH RUSSIAN POLISH ITALIAN TURKISH * menu items *: Themodels. may change depending on the 1 Press 7 twice to stop playback (if necessary), and then press SET UP. 2 Press 3 repeatedly to select "PREFERENCE PAGE". 3 Press 5/a to highlight one of the options below, and then press 3. · AUDIO (audio language) · SUBTITLE (subtitle language) · DISC MENU (disc menu language) 4 Press 5/a to select a language, and then press ENTER. 5 Repeat steps 3-4 for other language settings. 6 Press SET UP to exit from the menu. 16 En Playback Operation Playback Operation English Notes · If the prohibited icon ( ) appears on the TV screen when a button is pressed, the function for that button is not available on the current disc or at the current time. · Depending on the disc, some operations may operate differently or be restricted. Refer to the instruction supplied with the disc. · Do not push on the disc tray or put any objects other than discs on the disc tray. Doing so may cause this unit to malfunction. Selecting a track/chapter 1 Press l22 / 33l or use the numeric buttons (0-9) to select a track/chapter number. 2 During repeated playback, press l22 / 33l to replay the same track/chapter. Searching backward/forward 1 Press and hold l22 / 33l or press 2 / 3. 2 While searching, press l22 / 33l or 2 / 3 repeatedly to select the desired speed. Basic operation 1 Make sure this unit is turned on. 2 Press OPEN/CLOSE ( panel to open the disc tray. ) on the front 3 To resume normal playback, press 3 / 8. Note The 2 / 3 key may not be available with some discs. 3 Place the disc in the disc tray with the printed side up. 4 Press OPEN/CLOSE ( y ) again to close For MP3, WMA, WMV, and DivX®, the search function allows you to search the track currently being played. the disc tray. After recognizing the disc, this unit starts playback automatically. · If you press 3 / 8 when the disc tray is open, the disc tray closes and playback starts automatically. Repeat/Shuffle functions Repeat/Shuffle playback Each time you press REPEAT during playback, the front panel display changes as follows: DVD-Video RPT ONE (repeat chapter) RPT TT (repeat title) RPT ALL (repeat all) SHUFFLE (shuffle) RPT SHF (shuffle repeat) RPT OFF (repeat off) DVD VR format RPT ONE (repeat chapter) RPT TT (repeat title) RPT ALL (repeat all) RPT OFF (repeat off) 5 To pause playback, press 3 / 8 during playback. Playback is paused and the sound is muted. · Frame-by-frame playback can be done by pressing PAUSE ( ) on the front panel repeatedly. 6 To resume normal playback, press 3 / 8 again. 7 To stop playback, press 7. 17 En Playback Operation VCD/SVCD/CD RPT ONE (repeat track) RPT ALL (repeat all) SHUFFLE (shuffle) RPT SHF (shuffle repeat) RPT OFF (repeat off) MP3/WMA/WMV/DivX® RPT ONE (repeat file) RPT FLD (repeat folder) SHUFFLE (shuffle) RPT OFF (repeat off) Note For VCD/SVCD, repeat playback is not available when the PBC mode (see "Special VCD/SVCD features" on page 20) is on. To select a playback feature or item Use 2 / 3/5/a or the numeric buttons (0-9), and then press ENTER to start playback. To access or exit from the menu Press MENU. Playback in slow motion You can play back video in slow motion. 1 During playback, press 5 for reverse slow motion or a for forward slow motion. 2 During slow motion, press 5/a repeatedly to select the desired speed. 3 To resume normal playback, press 3 / 8. Repeating a section within a chapter/track 1 While playing a disc, press REPEAT A-B at the desired starting point. "SET A" appears in the front panel display. Note For VCD and SVCD, reverse slow motion is not available. Zooming pictures in/out You can enlarge or shrink the picture on the TV screen and pan through the enlarged picture. 2 Press REPEAT A-B again at the desired end point. · A and B can only be set within the same chapter/track. "RPT AB" appears in the front panel display and the selected section repeats continuously. 1 During playback, press ZOOM repeatedly to display the picture at different scales. · Use 2 / 3/5/a to pan through the enlarged picture. Playback continues. 3 To exit from the sequence, press REPEAT A-B. 2 Press ZOOM repeatedly to return to the original size. Operations for video playback (DVD/VCD/SVCD) Using the disc menu Depending on the disc, a menu may appear on the TV screen once you load the disc. Resuming playback from the last stopped point You can resume playback of the last ten discs, even if the discs were ejected or this unit was set to the standby mode. 18 En Playback Operation 1 Load one of the last ten discs. "LOADING" appears on the TV screen. 2 Press 5/a to scroll the information, and then press ENTER to access the selected item. English 2 Press 3 / 8 while "LOADING" is displayed on the TV screen. "RESUME PLAY" appears on the TV screen and the disc is played back from the last point. To cancel the resume mode When playback is stopped, press 7 again. Note For DVD VR format, resume playback is not available. 3 Use the numeric buttons (0-9) to input the number/time or press 5/a to make a selection, and then press ENTER. Playback changes to the selected time/ title/chapter/track. Changing the Title/Chapter/Track (DVD/VCD) 1 Press 5/a to select [TITLE], [CHAPTER] (DVD), or [TRACK] (VCD). 2 Press ENTER. 3 Select a title, chapter, or track number using the numeric buttons (0-9). Time search (DVD/VCD) Using the on-screen display (OSD) The OSD menu shows disc playback information (e.g., the title or chapter number, elapsed playing time or audio/subtitle language). A number of operations are possible without interrupting disc playback. 1 Press 5/a to select [TT TIME] / [CH TIME] (DVD) or [DISC TIME] / [TRACK TIME] (VCD). · [TT TIME] refers to the total time of the current title, and [CH TIME] refers to the total time of the current chapter. 1 During playback, press ON SCREEN. A list of available disc information appears on the TV screen. DVD MENU TITLE CHAPTER AUDIO SUBTITLE BITRATE 16 02/14 02/14 5.1CH ENG TITLE ELAPSED 0:02:25 2 Press ENTER. 3 Enter hours, minutes and seconds from left to right using the numeric buttons (0-9) (e.g. 0:34:27). Changing the Audio/Subtitle/Angle (DVD) You can change [AUDIO], [SUBTITLE], or [ANGLE] if these functions are available on the disc you are playing. VCD/SVCD MENU TRACK DISC TIME TRACK TIME REPEAT BITRATE 16 02/14 0:49:17 0:03:43 OFF TOTAL ELAPSED 0:02:25