EN ARRAY FRAME PRECAUTIONS CAUTION PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. HAF2-2112(W) Owner's Manual Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Thank you for choosing this Yamaha product. Please read this manual carefully before using it in a speaker installation. Keep the manual in safe place for future reference. · Before doing any installation or construction work, consult with an installation expert. · Make sure that the surface this bracket is being mounted on has the strength to handle the weight of both the speaker and this bracket. · Use bolts and nuts as well as washers for installation and tighten them firmly so that the speaker is secure and does not move. · Always loosen the corresponding screw before adjusting the angle or direction of the speaker. Never force this adjustment with the screw still tightened. · Some fittings may deteriorate over extended periods of time due to wear and/or corrosion. For optimum safety, the installation should be checked thoroughly at regular intervals. Package Contents HAF2-2112(W) 3-1101 3-1104 3-0235 2-1432 3-0112 Angle indicator plates (3 pcs.) Suspension plate (1 pc.) M10-40mm button head socket screws (8 pcs.) M10 flat washers (10 pcs.) M10 L-key wrench (1 pc.) NOTE · Use only the eye bolts included with the speaker unit. · For information on load limits and the strength of the eyebolt, refer to the owner's manual of the speaker. · The load limits and strength of the suspension plate are 114.5 kg (maximum). Yamaha cannot be held responsible for damage or injury caused by insufficient strength of the support structure or improper installation. * Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation. * Company names and product names herein are trademarks or registered trademarks of their respective companies. * Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. Installation Instructions 1. Flip the speakers upside down. Remove the existing speaker screws. Angle Indicator Plate (3-1101) M10 EyeBolt [2X] M10 Flat Washer [TYP] M10 Screw [TYP] Dimensions 3-1101 Angle Indicator Plate 2. Determine the splay angle of the speaker and the holes to use on the front joiner plate. Suspension Plate (3-1104) 11.000 .402 DIA. X. 485 SLOT 2X 3. Install two angle indicator plates on the bottom (facing up) of the speakers. Use the two slots of the angle indicator plate for the rear inserts of the speaker, as shown in the illustration. Install another angle indicator plate on the front inserts using the corresponding holes for the appropriate splay angle. The hole closest to the center is 0 degrees and the farthest is 15 degrees. Use the provided M10 button head screws and washers. 1/2-13 TAPPED HOLE 3.561 4. Slowly flip the speaker assembly so that the tops of the speakers are facing up. .402 14X 5. Install an angle indicator plate on the top front insert using the provided screws and flat washers. Use the same holes as the bottom front joiner plate. Angle Indicator Plate (3-1101) [2X] M10 Flat Washer M10 Screw [TYP] 3-1104 Suspension Plate 6. Install a suspension plate on the rear insert using the slot on the joiner plate, as shown in the illustration. Tighten the screws permanently. 11.000 30 .402 DIA. X. 485 SLOT 2X 1.750 1.175 7. Install the M10 eye bolts to the top of the speaker as shown in the illustration. For a tight pack, use the two outer holes of the speaker; for maximum splay, use the center holes of the speakers. 60 4.705 4.705 8. Use the bar of the suspension plate and the two eye bolts to suspend the speaker cluster assembly. .402 14X 9. For steep tilt angles, move the suspension plate to the bottom rear of the cluster and use the suspension bar as a pull back point. 60 Maximun Splay Configuration Tight Pack Configuration 5.500 .500 .402 3X ...