ARRAY FRAME EN PRECAUTIONS CAUTION PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. HAF3-2115(W) Owner's Manual Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Thank you for choosing this Yamaha product. Please read this manual carefully before using it in a speaker installation. Keep the manual in safe place for future reference. · Before doing any installation or construction work, consult with an installation expert. · Make sure that the surface this bracket is being mounted on has the strength to handle the weight of both the speaker and this bracket. · Use bolts and nuts as well as washers for installation and tighten them firmly so that the speaker is secure and does not move. · Always loosen the corresponding screw before adjusting the angle or direction of the speaker. Never force this adjustment with the screw still tightened. · Some fittings may deteriorate over extended periods of time due to wear and/or corrosion. For optimum safety, the installation should be checked thoroughly at regular intervals. Package Contents HAF3-2115(W) 3-1141 3-1144 3-1121 3-0235 Angle indicator plates (2 pcs.) Suspension plates (2 pcs.) Rear Joiner plates (2 pcs.) M10-40mm button head socketscrews (14 pcs.) 2-1432 3-0112 NOTE M10 flat washers (16 pcs.) M10 L-key wrench (1 pc.) Yamaha cannot be held responsible for damage or injury caused by insufficient strength of the support structure or improper installation. * Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation. * Company names and product names herein are trademarks or registered trademarks of their respective companies. * Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. · Use only the eye bolts included with the speaker unit. · For information on load limits and the strength of the eyebolt, refer to the owner's manual of the speaker. · The load limits and strength of the suspension plate are 114.5 kg (maximum). M10 EyeBolt [2X] M10 Flat Washer [TYP] Installation Instructions 1. Flip the speakers upside down. Remove the existing speaker screws. Dimensions Rear Joiner Plate (3-1121) [2X] M10 Screw [TYP] Suspension Plate (3-1144) [2X] 3-1141 Angle Indicator Plate 12.500 .402 DIA X 1.099 SLOT 2X 1/2-13 TAPPED HOLE 2. Determine the splay angle of the speaker and the holes to use on the front joiner plate. 3.731 3. Install a rear joiner plate on the rear inserts of the cluster with the provided screws and flat washers. Install two angle indicator plates on the front inserts using the corresponding holes for the appropriate splay angles with the screws and flat washers. Tighten permanently. .402 14X 4. Carefully flip the assembly to expose the top of the speakers. 3-1144 Suspension Plate 12.500 .402 DIA. X 1.099 SLOT 2X 1.750 1.175 5. Install a rear joiner plate on the rear inserts of the speaker using two M10 eye bolts and washers on the side speakers. Use the slot closer to the center hole as shown in the illustration. Install an M10 screw and washer on the center speaker. Tighten permanently. Angle Indicator Plate (3-1141) [2X] 4.750 4.705 6. Install two suspension plates on the front inserts of the speakers using the same holes as the angle indicator plates. Make sure to match the hole positions on the bottom and top suspension plates. 60 .402 14X 6.250 .500 17.701 .402 DIA X 30°SLOT 2X 1/2-13 TAPPED HOLE .402 3X 3-1121 Rear Joiner Plate 7. Use the two eye bolts on the rear and the front to suspend the speaker cluster assembly. 120 8. For steep tilt angles, move the rear eye bolts to the rear bottom insert of the speaker cluster and use as a pull back point. Make sure to replace the eye bolts with the provided screws and washers. Tight Pack Configuration 6.20 14.016 16.074 120 Maximun Splay Configuration ...