User s Manual (English Edition) Model : ZM-2HC2 NP Heatpipe HDD Cooler * Please read before installation http:// www.zalman.co.kr http:// www.zalmanusa.com 1. Product Features Cools HDD for more stable operation Reduces HDD noise and vibration Fanless design ensures noiseless, maintenance-free operation NP is an Acronym for "Noise Prevention". 2. Specifications Name Weight Materials Dimensions Heat Dissipating Area NP Heatpipe HDD Cooler 270g Aluminum, Copper, Rubber 143.5(L) X 146.5(W) X 36.5(H) mm 415 cm2 3. Patent Applications Patent Applications Pending in over 20 nations around the world, including the U.S.A., EU, and Japan Korean Patent Applications : No. 03-26421 4. Compatible HDDs 3.5-inch Hard Disk Drive for PCs Standard Size : 146 X 101.6 X 25.4 (20) mm 1 5. Exploded View Damper Heatpipe Al Bar Damper A-Type Bolt B-Type Bolt Ground Wire Mounting Hole Sticker Manual 2 6. Components Assembed NP Heatpipe HDD Cooler - Two (2) Al Bars - Eleven (11) Heatpipes Four (4) A-Type Bolts : For fastening the HDD Four (4) B-Type Bolts : For installing the HDD Cooler Four (4) Dampers : For reducing the HDD noise and vibration One (1) Ground Wire : For Grounding the HDD Spare Parts : A-Type Bolt, B-Type Bolt, Damper (One of Each) Mounting Hole Sticker : For indicating the drilling positions on the case User's Manual See the on page 2 to identify the above components. 7. Before Installing 1) Use a small amount of force : if excessive force is used when installing, the product may warp or be deformed. 2) Zalman Tech. Co., Ltd. is not responsible for any problems arising from using the product outside its intended purpose. 3) HDD coupled with NP Heatpipe HDD Cooler should always be installed in the case with the heatpipes facing up. [Refer to pictures below] (O) (X) 3 8. Installing the HDD 1) Seat the NP Heatpipe HDD Cooler Seat the NP Heatpipe HDD Cooler on the HDD as shown in the diagram. (Note the locations of the holes) Holes HDD A-Type Bolt 2) Fasten the HDD Screw the 4 A-Type Bolts into the holes and firmly tighten. Al Bar HDD 9. Installing the HDD Cooler in the 5.25-inch Drive Bay 1) Install the Dampers & the Ground Wire Install the 4 Dampers in the NP Heatpipe HDD Cooler. Insert the thread of one of the dampers through the ground wire's round terminal for the ground. [Refer to arrow A] Damper A Ground Wire 4 2) Install into 5.25-inch Drive Bay Slide the completed assembly into the PC's 5.25-inch drive bay and firmly fasten with 4 B-Type Bolts. Use one of the B-Type Bolts to link the ground wire's Y-terminal to the chassis. [Refer to arrow B] Note) Tighten the B-type bolts enough so that they are firm, but do not cause distortion of the dampers. B-Type Bolt B 10. Installing the HDD Cooler in the Case 1) Install the Dampers & the Ground Wire Install the 4 Dampers in the holes on the bottom side of the HDD. Insert the thread of one of the dampers through the ground wire's round terminal for the ground. [Refer to arrow C] Ground Wire Damper C 5 Attach the Mounting Hole Sticker to the case in which you wish to install the HDD Cooler and drill 4 holes with 4 drill. Power Supply Mounting Hole Sticker Power Supply B-Type Bolt Put the HDD Cooler on the frame of the case and firmly fasten with 4 B-Type Bolts. Use one of the B-Type Bolts to link the ground wire's Y-terminal to the chassis. Note) Tighten the B-type bolts enough so that they are firm, but do not cause distortion of the dampers. 6 11. To Build a Noiseless System ZM300A-APF : Power Supply ZM-NB47J : Northbridge Cooler CNPS Series CPU Coolers ZM-F1 : Case Fan ZM80X-HP : Heatpipe VGA Cooler ZM300A-APF ZM-NB47J ZM-F1 CNPS7000 Series ZM80X-HP CNPS6000 Series For more information on our products, visit our website at www.zalman.co.kr. 7 ...