LAVADORA-SECADORA WASHER-DRYER WDD 1022 WDD 1022 132995220 MANUAL DE USO USER MANUAL E GB Dear customer, Please read these operating instructions carefully and pay particular attention to the safety notes indicated in the first pages. We recommend that you keep this instruction booklet for future reference and pass it on to any future owners. Transport damages When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre. The symbols you will see on some paragraphs of this booklet have the following meaning: The information marked with this symbol provides additional instructions and practical tips on the use of the appliance. Tips and information about economical and ecological use of the machine are marked with this symbol. Our contribution to the protection of the environment: we use recycled paper. Contents Warnings Disposal Tips for environmental protection Technical specifications Installation Unpacking Positioning Water inlet Water drainage Electrical connection 22 23 23 23 24 24 24 24 24 25 Maximum loads Laundry weights Removing stains Detergents and additives Drying hints Load Garments not suitable for drying Drying symbols on garment labels Duration of the drying cycle Modification of the drying time Fibre residue Additional drying International wash code symbols Operating sequence - Washing only Washing programmes Drying programmes Operating sequence - Drying 28 28 28 29 30 30 30 30 30 30 30 30 31 32 33-34 35 35 Description of the appliance Door reversal Use Control panel Controls Washing hints Sorting the laundry Temperatures Before loading the laundry 25 26 27 27 27 28 28 28 28 Maintenance Bodywork Detergent dispenser drawer Drain filter Water inlet filter Emergency emptying out Frost precautions 36 36 36 36 36 37 37 Something not working? 21 38-39 ENGLISH The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly important for your safety or correct functioning of the appliance. Warnings The following warnings are provided in the interests of overall safety. You must read them carefully before installing or using the appliance. Installation · All internal packing must be removed before using the appliance. Serious damage may be caused to the machine or adjacent furniture if the protective transit devices are not removed or are not completely removed. Refer to the relevant paragraph in the instruction book. · Any electrical work required to install this appliance must be carried out by a qualified electrician. · Any plumbing work required to install this appliance must be carried out by a qualified plumber. · After having installed the machine, check that it is not standing on its electrical supply cable. · If the appliance is placed on a carpeted floor, ensure that air can circulate freely between the feet and the floor. · Always check that water has emptied out before opening the door. If not, drain the water following the instructions in the instruction book. · Always unplug the appliance and shut the water tap after use. General safety · Repairs to the machine must be carried out only by qualified personnel. Repairs carried out by inexperienced persons could cause serious danger. Contact your local Service Centre. · Never pull the power supply cable to remove the plug from the socket; always take hold of the plug itself. · During high temperature wash programmes and during the drying cycle the door glass may get hot. Do not touch it! Use · This appliance is designed for domestic use. It must not be used for purposes other than those for which it was designed. · Only wash and dry fabrics which are designed to be machine washed and dried. Follow the instructions on each garment label. · Do not overload the appliance. Follow the instructions in the instruction book. · Make sure that all pockets are empty. Objects such as coins, safety pins, pins and screws can cause extensive damage. · Do not machine wash garments saturated with petroleum, methylated spirits, trichlorethylene, etc. If such fluids have been used to remove stains prior to washing, wait until they have completely evaporated from the fabric before placing garments in the appliance. · Place small items such as socks, belts, etc. in a cloth bag or pillowcase to prevent them getting trapped between the drum and the tub. · Use only the recommended quantities of fabric softener. An excessive amount could damage the laundry. · If you use a liquid detergent with a dispenser which has to be placed directly in the drum, remember to remove this dispenser before drying. · Leave the porthole door slightly ajar when the appliance is not in use. This preserves the door seal and prevents the formation of musty smells. Child safety · Children are often not aware of how dangerous electrical appliances can be. When the machine is working, children should be carefully supervised and not be allowed to play with the appliance. · The packaging components (e.g. plastic film, polystyrene) can be dangerous to children - danger of suffocation! Keep them out of children's reach. · Keep all detergents in a safe place out of children's reach. · Make sure that children or pets do not climb into the drum. · When the appliance is to be scrapped, cut off the electrical supply cable and destroy the plug with the remaining cable. Disable the door catch in order to prevent children from becoming trapped inside while playing. 22 Disposal Packaging materials The materials marked with the symbol recyclable. >PE<=polyethylene >PS<=polystyrene >PP<=polypropylene are This means that they can be recycled by disposing of them properly in appropriate collection containers. Machine ENGLISH Use authorised disposal sites for your old appliance. Help to keep your country tidy! Tips for environmental protection To save water, energy and to help protect the environment, we recommend that you follow these tips: · Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!). · The machine works more economically if it is fully loaded (for both washing and drying cycles). · The machine will consume less energy if the laundry is adequately spun before being dried. · With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature. · Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed. Technical specifications DIMENSIONS Height Width Depth 85 cm 60 cm 60 cm WASHING 5 kg 2.5 kg 2.5 kg 2 kg 1000 rpm max. 220-230 V/50 Hz 2200 W 10 A 50 kPa 800 kPa DRYING 2.5 kg 2 kg MAXIMUM LOAD Cotton Synthetics Delicates Woollens SPIN SPEED POWER SUPPLY VOLTAGE/FREQUENCY TOTAL POWER ABSORBED MINIMUM FUSE PROTECTION WATER PRESSURE Minimum Maximum This appliance complies with the following EEC Directives: 73/23/EEC of 19/02/73 relating to low voltage 89/336/EEC of 03/05/89 relating to electromagnetic compatibility. 23 Installation Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 1. Using a spanner, unscrew and remove the rear right-hand bolt and lay the machine on its back, taking care not to squash the hoses. This can be avoided by placing one of the corner packing pieces between the machine and the floor. Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units. Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. P1051 P0255 Water inlet Connect the water inlet hose supplied with the machine to a tap with a 3/4" thread. Do not use already employed hoses. The other end of the inlet hose which connects to the machine can be turned in any direction. Simply loosen the fitting, rotate the hose and retighten the fitting, making sure there are no water leaks. 2. Remove the polystyrene block from the bottom of the machine and release the two plastic bags. 3. Carefully remove the right-hand bag (1) then the left-hand bag (2) by pulling them towards the centre of the machine. 2 P1068 P1066 1 4. Set the machine upright and remove the two remaining bolts from the back. 5. Pull out the three plastic spacers from the holes into which the bolts were fitted. 6. Plug the open holes with the plugs which you will find in the envelope containing the instruction booklet. P1088 P0021 The inlet hose must not be lengthened. If it is too short and you do not wish to move the tap, you will have to purchase a new, longer hose specially designed for this type of use. Water drainage The end of the drain hose can be positioned in three ways: Hooked over the edge of a sink using the plastic hose guide supplied with the machine. In this case, make sure the end cannot come unhooked when the machine is emptying. P0256 P0020 24 This could be done by tying it to the tap with a piece of string or attaching it to the wall. Electrical connection This machine is designed to operate on a 220-230 V, single-phase, 50 Hz supply. Check that your domestic electrical installation can take the maximum load required (2.2 kW), also taking into account any other appliances in use. Connect the machine to an earthed socket. The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution. Should the appliance power supply cable need to be replaced, this should be carried out by our Service Centre. Important! When the appliance is installed the power supply cable must be easily accessible. P0022 In a sink drain pipe branch. This branch must be above the trap so that the bend is at least 60 cm above the ground. Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm. The end of the drain hose must always be ventilated, i.e. the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose. The drain hose must not be kinked. Run it along the floor; only the part near the drainage point must be raised. P0023 Description of the appliance 1 3 1 Detergent dispenser drawer 2 Programme chart WDD 1022 3 Control panel 4 Door handle 5 Drain filter 6 Adjustable feet 2 4 5 6 25 ENGLISH Door reversal The opening direction of the outer door on this washing machine can be reversed. To carry out this operation, proceed as follows: 1) Disengage the end of the opening stop (1) from the door and turn it through 90° to remove it from its seat (Fig. A). 2) Using a screwdriver, turn plastic plug (2) through 90° to remove it from its seat (Fig. A). 3 ) Fit plug (2) in the hole left free by opening stop (1 ) and turn it through 90° to lock it into place (Fig. B). 4) Fit opening stop (1) into the hole from which plug (2) was removed and turn it through 90°, making sure that the latching tooth is facing towards the right (Fig. B). 5) Remove the door by unscrewing the screws securing it to the bottom hinge (3 - Fig. A). 6) Unscrew the two plastic screws (4 - Fig. A) and fit them on the opposite side (4 - Fig. B). 7) Remove the catch hook (5 - Fig. A) by inserting a screwdriver into the upper hole and pushing downwards. 8) Remove plate (6) by inserting a screwdriver into the bottom hole and pushing upwards (Fig. A). 9) Refit the catch hook (5) and plate (6) on the opposite sides.(Fig. B). 10) Remove the door catch (7) and plate (8) as explained in paragraph 7. 11) Turn the door through 180°. 12) Refit the door catch (7) and plate (8), reversing their position and pressing firmly to engage the hook (Fig. B). 13) Fit the door onto the washing machine. Insert the top pin first, then the bottom pin into the hinge (3 - Fig. B); finally screw the hinge onto the washing machine. 14) Check that the door is aligned with the appliance. To do this, loosen screw (9 - Fig. B) by a couple of turns and re-tighten when alignment is correct. 15) Fit the flexible end of the door opening stop into the location provided in the door (1 - Fig. B). P0535 6 7 2 5 8 1 93 1 5 4 A P0534 6 7 2 4 39 8 B Fitting a door panel The door of this washing machine has mouldings to allow fitting of a decorative panel (stainless steel sheet, laminated plastic, wood, etc.) to match with the existing kitchen units. The dimensions of the panel must be as follows: Width Height Maximum thickness 588 mm 588 mm 4 mm To fit the panel, remove the moulding by unscrewing its fixing screws. Position the panel, then refit the moulding, making sure that it comes into contact with and firmly clamps the panel. 26 Use Control pane ...